User manual PYLE PLVS7HM

7INCH WIDE TFT LCD MONITOR Precautions Please read this manual completely and carefully prior to attempting to install your new car video equipment. Install correctly, your new equipment will provide you with year of enjoyable and safe usage. Installation of this equipment in any portion of a vehicle which impairs or distracts the driver is improper and dangerous. We assumes no liability whatsoever for failure to follow the proper installation of this products. 1.Do not operate this equipment while driving-safe driving should always be your highest priority. 2.Do not install components in areas which are susceptible to rain, moisture direct sunlight, extreme heat or cold, excessive dust, dirt or humidity. 3. Immediately unplug the power cord and send the monitor to your local dealer or service center as soon as possible: a) if there is smoke or any peculiar odor present during use b) if there is damage to any of the internal components 4. To avoid damage to the monitor and risk of electronic shock, do not permit any of this equipment to become damp or wet from water or liquid. If this does occur, immediately unplug the power cord and send the monitor to your local dealer or service center as soon as possible. 5. Do not attempt to repair, open or dissemble any of the components. Dangerous high voltages are present which may result in electric shock. 6. Use only a power source with 12 volts DC (negative ground). 7. Do not place objects on or suspend objects from the power cord, as this may damage the cord. 8. Do not twist or place the power cord near any source of heat in the vehicle. 9. Do not attempt to repair a damaged, broken or faulty power cord. Replace it with a new one immediately. 10. Avoid dropping any metal objects or inflammable items into the monitor ventilation slots. 11. After the monitor is installed, do not arbitrarily pull it down or strike it. This may loosen the mounting screws and cause it fall down. 1. Control and layout for the monitor Notice: some functions are work by remote control. 2 Control and layout for the remote control 2. Notice: If the monitor does not have the function, the button would not be work. 3 Function Press FUNCTION button< > on the remote or press manual button< the monitor to call out the function menu. > twice from PRESS UP < > OR DOWN < > BUTTON TO SELECT FUNCTION Fixed Press left < > or right < > button to select your favorite display language Press left button < >to adjust hours & press right button < >to adjust minute Press left or right button < > to select auto on/off Press left or right button < > to call out the calender Press the left or right button < to call out the game Press < > to invert the picture left or right Press < > to invert the picture up or down > Games Press < > to enter the games. Start --Menu Button < > Move --Down Button < > Roll --Up Button < > Exit --Mute Button < > Level --AV Button < > Pause --Menu Button < > Move Left --Volume Button < > Move Right --Volume Button < > Calendar Press FUNCTION < >to call out the function menu, then Press < > to select CALENDAR and press left or right to < > to call out the CALENDAR Adjust increase of year, press < > button Adjust decrease of year, press < > button Adjust increase of month, press < > button Adjust decrease of month, press < > button Installation Power Cord (Female) Video 1 input (red) Video 2 input (yellow) Ground (black) DC 12V power input (red) Remote Control replacing batteries PULL OUT PUSH 1) Always use new batteries when replacing the old set. 2)Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 3)Battery replacement is necessary when remote control acts sporadically or stops operating. 4)Do not drop, apply shock or step on the remote control 5)Do not spill water on the remote control 6) Do not place objects between the remote control and remote sensor. 7)Do not use remote controls for other equipments at the same time. 8)If the MONITOR does not operate even when operating the remote control from a close range, it is time to replace the batteries (use CR-2025), refer to the label on back of the basic control. 4 Unscrew it and takeaway the back cover before install to headrest housing or sun-visor housing CAUTION: make sure the screw are not long enough to go through the headrest! If you have any doubts about this type of installation, please consult your local mobile electronics retailer. Cutting and make holes in the headrest will cause damage which is expansive to repair. Step of install headrest housing Setup work remove the headrest and set it in an uncluttered work area. Take the appropriate precautions to ensure that it is not damaged during the installation. 6 Measurements Push on the headrest with your fingers to make sure there are no obstructions that would hinder the installation. Use the paper template to mark the area to be cut. Cut the headrest using an adjustable-depth blade, start your cut 1/4 inch inside one corner and cut diagonally across, stopping 1/4 inch in from the other corner. Repeat the procedure for the other two corners. Remove foam & obstructions Carefully peel back the material. Set the adjustable blade to one inch depth and cut around the edges of the hole, staying 1/4 inch inside the edge. Pull up one corner of the foam and use the blade to cut underneath. Remove small section at a time, using the pull up and cut method for uniform depth. Use a dremel or other appropriate tool to remove other obstructions. Insert the monitor to measure the fit and make adjustments if necessary 7 Step of install sun-visor housing Setup work remove the visor and set it in an uncluttered work area. Take the appropriate precautions to ensure that it is not damaged during the installation. Measurements Push on the headrest with your fingers to make sure there are no obstructions that would hinder the installation. Use the paper template to mark the area to be cut. Cut the visor using an adjustable-depth blade, start your cut 1/4 inch inside one corner and cut diagonally across, stopping 1/4 inch in from the other corner. Repeat the procedure for the other two corners. 9 Remove foam & obstructions Carefully peel back the material. Set the adjustable blade to one inch depth and cut around the edges of the hole, staying 1/4 inch inside the edge. Pull up one corner of the foam and use the blade to cut underneath. Remove small section at a time, using the pull up and cut method for uniform depth. Use a dremel or other appropriate tool to remove other obstructions. Insert the monitor to measure the fit and make adjustment if necessary Route the cable through the visor Run the supplied cable through the opening and out the top of the visor. If possible, conceal the wires using a shaft covering. Connect the power, ground and video leads to test the MONITOR. Before connecting the monitor, pull the connecting cable assembly through the visor housing as shown in diagram. Place visor housing into the opening and secure with correct fasteners. Install the sun-visor housing Pull the connecting cable through the center of the housing as shown in diagram, and secure with correct fasteners 10 Technical parameter s LCD Drive Method: TFT Active Matrix Display Size: 7 Inch Wide Screen (Diagonal) Aspect: 16:9 Display Format: 480 x RGB x 234 Number of Pixels: 1440 x 234 Video System Input: NTSC/PAL Auto-select Back Light: High Brightness Type U Shaped CCFT Power Source: DC12V Current Consumption: 8W Dimension (H x W x D): 113 x 182 x 25 (mm) Stand Style Dimension (H x W x D): 128 x 195 x 24 (mm) Headrest Style Dimension (H x W x D): 127 x 236 x 25 (mm) Sun Visor Style