VEHICLE SECURITY SYSTEM Optional Remote Start Module and 2-way Transmitter Instructions Included SYSTEM MANUAL Button 1 STANDARD FEATURES Some of the system's standard features include: · 4-button remote transmitter · LED Status indicator · Valet switch · Extended Range Receiver · 125dB Multi-tone siren · Dual stage impact detector · Remote panic · Remote Valet mode · Remote chirp delete · Remote sensor bypass · Passive or active arming · Flashing parking lights · Auto Rearming OPTIONAL FEATURES This system has many optional features that may require additional parts and/or labor. Please contact your dealer for more details. · Remote keyless entry (door lock/unlock) · Illuminated entry · LCD 2-way Remote · Hood & trunk protection · Trunk/hatch release · Window roll-up · Additional sensors · Remote Start (optional plug-in module) · Stop & Go Feature · Auto Cold Start Note: Some features may not be appropriate for certain vehicles. 1 REMOTE TRANSMITTER BUTTONS Button 2 Button 3 Button 4 Transmitter Icons NOTE: Transmitter cosmetics may differ between models and between standard 1-way and LCD 2-way transmitters, but button functions remain the same as described below. Each transmitter button has two operating modes: standard and level shifted. Pressing a transmitter button for less than one second activates the standard function associated with that button (such as arm or disarm). Pressing a button for more than one second changes the color of the standard transmitter's LED to green and activates the level shift feature. While the LED is green (level shifted), pressing any transmitter button accesses another level of commands providing expanded operation. ARMING OPERATION To arm the system press transmitter button 1: · The siren will chirp once. · The parking lights will flash once.* · The doors will lock.* · The LED will turn solid for 10 seconds then start flashing slowly. After 10 seconds the system is armed. During Arming, if an open hood or trunk is detected, the system will wait 10 seconds for the zone to close. If a door is open the system will wait up to 60 seconds for the zone to close (depending on door zone setting during installation). If a zone remains open after the wait period, the siren will chirp, the parking lights will flash 4 times to indicate the zone is still open. The system will then ignore that zone, but keep all other areas protected. While Armed, the system will trigger if: · The door, hood, or trunk is opened. · The shock sensor detects an impact. · An optional sensor is disturbed. When triggered by the door or hood/trunk input the siren will sound, the horn will honk, and the parking lights will flash for 30 seconds. If triggered by a sensor, the alarm cycle will last 15 seconds. If the alarm is triggered while the optional remote start is engaged, the remote start will immediately shut down. If a zone triggers the system 3 times during a single arming cycle, the system will bypass that zone, keeping the other zones protected, until the next time the system is armed. If the shock sensor detects a light impact to the vehicle or an optional sensor is disturbed, the system will chirp and the parking lights will flash 5 times to warn away the potential intruder. *Optional Feature 2 PASSIVE ARMING OPERATION The passive arming feature allows the system to arm automatically without user intervention.This feature can be toggled on/off using the transmitter. To turn passive arming on/off: 1. Press and hold button 2 for level shift. 2. Press button 4. · The system will enter passive arming operation mode. · The optional 2-way LCD transmitter display will show "LAST DOOR ARM". To arm the system passively: 1. Turn the ignition key off. 2. Exit the vehicle and close all doors. · The siren will chirp and parking lights will flash once after closing the last door. · The LED flashes rapidly indicating that the system is preparing to arm. (The system can be armed at any time by pressing transmitter button 1.) NOTE: Opening the hood/trunk or a door resets the passive arming timer. · After 30 seconds the siren will chirp to indicate the system is armed. · The doors will lock.* If Passive Locking was enabled during installation. DISARMING OPERATION To disarm the system press transmitter button 2. · The siren will chirp twice.¥ · The parking lights will flash twice.¥ · The doors will unlock.* · The dome light will turn on.* ¥ * If the alarm was triggered while away, the system will respond with 3 chirps and 4 parking light flashes. Optional Feature. TAMPER ALERT If the alarm was triggered while away from the vehicle, the siren will chirp 3 times on disarming for tamper indication. The triggered zone will be shown on the optional 2-way LCD transmitter display. AUTO REARM If the system was armed for at least 10 seconds, the Auto Rearm feature allows the system to automatically re-arm itself 30 seconds after disarming. The doors will also re-lock if selected during installation. NOTE: Opening the door resets the rearm timer, and opening the trunk, hood, or turning on ignition cancels the auto rearm feature. AUTO IMMOBILIZER The Auto Immobilizer feature automatically engages the starter defeat relay 30 seconds after turning off the ignition. This feature provides an extra level of security even when when the alarm is not set. When immobilized, the vehicle will not start with the key until either transmitter button 2 is pressed, or the override button is pressed with the ignition on. NOTE: The auto immobilizer feature does not operate while in the valet mode. To turn the immobilizer on/off: 1. Press and hold button 2 for level shift. 2. Press button 3. · The optional 2-way LCD transmitter display will show "IMMOBILIZE". SILENT OPERATION MODE Press transmitter button 4 to turn the arm and disarm chirps on/off. NOTE: If the system is disarmed, pressing button 4 to change the siren status also arms the system. To disarm the system, press button 2. NOTE: The optional 2-way transmitter will still beep to confirm systems arm/disarm. 3 IGNITION CONTROLLED LOCKS The ignition controlled locks feature allows the doors to automatically lock when the brake pedal is pressed (after turning on the ignition and closing all doors), and automatically unlock when the ignition key is turned off. The ignition controlled locking feature may also be programmed for ignition lock without ignition unlock, and off (no ignition control). NOTE: If the optional remote start module is not installed and ignition locking is desired, the feature must be programmed for use without brake. See Alarm Programmable Features. REMOTE PANIC In the event of an emergency (PANIC) situation, the system's siren can be triggered for 30 seconds to attract attention. To activate the Panic Feature: Press transmitter buttons I&2 for 3 seconds. · The siren will sound. · The parking lights will flash. · The starter defeat will activate. Press button I to exit panic mode and rearm the system. Press button 2 to exit panic mode and disarm the system. The Panic Feature will NOT operate when the ignition is on. EMERGENCY OVERRIDE If the transmitter becomes lost or fails to operate, the system can be disarmed by using the emergency override feature. To override the system: 1. Enter the vehicle. · Because the system is armed, the siren will sound. 2. Turn on the ignition key. 3. Press the Valet switch for 3 seconds. · The siren will stop sounding. · Starter defeat bypassed. VALET MODE When the system is placed into the Valet Mode the security and remote start features will be disabled. However, the optional keyless entry and trunk release features will still function if installed.The valet mode may be accessed with either the valet switch or a remote transmitter. To enter or exit valet mode using the switch: 1. Be sure the system is disarmed. 2. Turn ignition on. 3. Press and hold the valet switch for 3 seconds. · The siren will chirp 3 times to enter or exit valet. 4. Turn ignition off. · The LED will turn on solid indicating the system is in valet mode, or turn off indicating valet mode exit. To enter or exit valet mode using the remote: 1. Press and hold button 1 for level shift. 2. Press button 1 again to turn valet mode. · The parking lights will flash 4 times to enter and 3 times to exit valet. · The LED will turn on solid indicating the system is in Valet Mode, or turn off indicating Valet Mode exit. · The optional 2-way LCD transmitter display will show "zzz" for valet . OPTIONAL TRUNK RELEASE The activate the system's auxiliary feature (or trunk release) press button 3 for level shift, then press button 3 again. If the vehicle's trunk pin is connected to the alarm, the optional 2way LCD transmitter will show the trunk open. OPTIONAL TRUNK DISARM The trunk disarm feature allows the alarm to disarm automatically when the auxiliary output is used to activate the optional trunk release. This eliminates having to first disarm the alarm 4 before activating the trunk release. NOTE: This feature must be programmed during installation and only function if auxiliary is programmed for momentary output. CAR LOCATOR FEATURE The activate the system's car locator feature press button 3 twice rapidly. The siren will chirp and the parking lights will flash 6 times. REMOTE SENSOR BYPASS To bypass the shock sensor's warn-away while the system is armed, press button 1 twice rapidly. To bypass the sensor completely, press button 1 twice again. Pressing button 1 twice a third time will re-activate the sensor. The parking lights will flash to indicate the mode: One Flashes = Normal Two Flashes = Sensor 1 Warn away Bypass Three Flashes = Sensor 1 Complete Bypass If an optional dual-zone sensor is connected to the optional sensor port, that sensor's warnaway feature can be bypassed while the system is armed by pressing button 4 twice rapidly. To bypass the sensor completely, press button 4 twice again. Pressing button 4 twice a third time will re-activate the sensor. The parking lights will flash to indicate the mode: Four Flashes = Sensor 2 Warn away Bypass Five Flashes = Sensor 2 Complete Bypass NOTE: The system must be armed for at least 10 seconds prior to activating the remote sensor bypass feature. OPTIONAL ANTI-CARJACK FEATURE When selected, the optional anti-carjacking feature monitors the vehicle's doors while the ignition is on. If a door is opened, the anticarjacking feature will trigger, with progressively higher levels of alert. The Anti-Carjacking feature must be enabled during installation. To activate anti-carjack protection: 1. Make sure the ignition is on and all doors are closed. 2. Press the valet switch once. If the carjack feature is triggered: · The LED will flash rapidly. · Warn Trigger will activate after 30 seconds. The parking lights will begin flashing and the siren will begin chirping. · Full Trigger will activate after 60 seconds. The siren will sound continuously and the starter defeat will turn on and remain on until the carjack feature is deactivated . To deactivate anti-carjack if not triggered: Press the valet switch for 3 seconds. · The siren will chirp 3 times. - or Turn off the ignition with all doors closed. To deactivate anti-carjack after Warn Trigger: Press the valet switch for 3 seconds. · The siren will chirp 3 times. - or Press transmitter button 2. To deactivate anti-carjack after Full Trigger: Press the valet switch for 5 seconds. - or Enter PIN if programmed for PIN mode. OPTIONAL SECURE PIN CODE The system may be programmed to override only when a 2-digit personal identification number is entered using the valet switch. PIN code override mode must be selected during installation or PIN code mode will not operate. To disarm the system with a PIN code: 1. Open door, alarm system will trigger 2. Turn ignition on 3. Press the override switch the number of times equal to the first digit of the PIN. 5 4. Turn ignition off, then back on. 5. Press the override switch the number of times equal to the second digit of the PIN. 6. Turn ignition off. · The system will disarm. Example: PIN=2,3 Press valet switch two times, turn ignition off then back on, and press valet switch 3 more times. CREATING A SECURE PIN CODE When first programmed for PIN code override mode, the default code is set to 1,1. To change the PIN code first program the system for PIN code operation, then follow the steps below: To change the PIN code: 1. Be sure the ignition is off and the system is disarmed. 2. Press the valet switch 4 times. 3. Turn ignition on. · The siren will chirp 4 times. 4. Press the valet switch once. · The siren will chirp once and enter 1st digit PIN programming. 5. Pick a 1st digit number from 1 to 4, and press the transmitter button equal to that number (example: number 2=button 2). · The siren will chirp a number of times equal to the button pressed. 6. Press the valet switch again. · The siren will chirp twic ...