PYD6070/PYD1270 6/12 channel 2 Bus pro series professional mixing console Your PYLE PRO Series Compact Mixing Console is a sophisticated control center, perfect for mixing sound from multiple signal sources such as MICROPHONES, GUITAR, GUITAR AMP,KEYBOARD, SAMPLER, DRUM MACHINE or AUDIO OUTPUT FROM A VCR. This mixer is ruggedly constructed for home or professional use. Wide range of volume controls permit you to adjust sound levels accurately to achieve just the right mix for playing through your speaker system or for recording. Owner's Manual Table of Contents i Introduction 1 Safety Instructions Care and Maintenance 2 Features and Controls: PYD6070 Mixer 3 Features and Controls: PYD1270 Mixer 4 INSTALLATION, PYD6070 Mixers 5 INSTALLATION, PYD1270 Mixers 6 Mono Input Channel Controls, MIC/LINE/GAIN/EQ/EFX/PAN/PEAK/LEVEL/LO CUT(PYD1270) CH1/CH2 For PYD6070 CH1/CH2/CH3/CH4 For PYD1270 7 Stereo Input Channel Controls, LINE/EQ(PYD6070)/EFX/BAL/LEVEL/GAIN(PYD1270) CH3/4 & CH5/6 For PYD6070 CH5/6, CH7/8, CH9/10, & CH11/12 For PYD1270 8-9 Main Section Connections and Controls 10 Specifications 11 Warranty i ­ Pyle Pro Mixer PYD6070/1270 Owner's Manual Safety Instructions CAUTION: To reduce the risk of electronic shock, do not remove the cover (or back). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire electric shock, do not expose this device to rain and moisture. This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure-voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual. This device should be kept away from water or liquid to be spilled into the unit. This device should be kept away from heat sources such as raditors, heat registers, stoves, etc. This device should be situated so that its location or position does not interfere with its proper ventilation. Care and Maintenance Your PYLE PRO mixer is an example of superior design and craftsmanship. The following suggestions will help you care for your mixer so you can enjoy years of use: · Keep the mixer dry, if it gets wet, wipe immediately. · Use the mixer only in well ventilated installations. · Handle the mixer gently and carefully-do not drop. · Keep the mixer away from dust and dirt. · Wipe occasionally with a damp cloth to keep it looking new. Do not use harsh chemicals, solvents or detergents. Pyle Pro Mixer PYD6070/1270 Owner's Manual ­ 1 Features and Controls: PYD6070 Mixer MIC1 & MIC2 Balanced XLR Input Connector For connecting a balanced low impedance microphone with XLR type plug. EFX SEND/RETURN Jacks Permit you to either include externally generated effects (such as a digital sampler or synth) IN the mix, or to process the mixed sound (echo reverb, etc.). HEADPHONES Jack Accepts the headphones with 1/4" plug. CTRL ROOM OUT Jacks To connect the mixer to a second receiver or amplifier powering speakers in the control room or in a remote location. POWER ON Indicator LINE 1 & LINE 2 BAL or UNBAL 1/4" (TRS) Input Jack For connecting a balanced or unbalanced line level sources. MIC1/LINE 1 & MIC2/LINE 2 GAIN Control Lets you adjust the gain of the input source. MAIN OUT Jacks To connect the mixer to a receiver or amplifier. LINE 3/4 & LINE 5/6 BAL or UNBAL 1/4" (TRS) Input Jacks For connecting a balanced or unbalanced stereo line level sources. Use LEFT input jack only for each channel, if the source signal is mono. TAPE IN & OUT Jacks To connect the mixer to a tape deck for recording the mixed program and for auditioning mix playback from tape. TAPE TO MIX Switch Press to route the signal playback from tape to the MAIN mix bus. DUAL LED DISPLAY METER Indicates the levels of left and right MAIN outputs. PHANTOM +48V DC Switch with Indicator Press to accept the use of condenser microphones. CH1, CH2, CH3/4, & CH5/6 Tone Controls (EQ) CH1, CH2, CH3/4, & CH5/6 EFX Control Lets you adjust the channel signal level sent to the external effect. CH1 & CH2 PAN Control Lets you adjust the channel signal level feeding the L & R mix bus. CH1 & CH2 PEAK Indicator Indicates the channel signal is going into overload. CH1, CH2, CH3/4, & CH5/6 LEVEL Control Lets you adjust the channel signal level sent to the MAIN mix bus. MASTER Level Control Lets you adjust the signal level of MAIN and TAPE outputs. EFX RETURN Level Control Lets you adjust the effects signal level sent to the MIAN mix bus. CONTROL ROOM/PHONES Level Control Lets you adjust the signal level sent to the control room and headphones. TAPE TO CONTROL ROOM Switch Press to route the signal playback from tape to the control room. CH3/4 & CH5/6 BAL Control Lets you adjust the channel signal levels of left and right relative to each other before both signals are then sent to the MAIN mix bus. It allows you to balance the source in the stereo image. 2 ­ Pyle Pro Mixer PYD6070/1270 Owner's Manual Features and Controls: PYD1270 Mixer EFX SEND/RETURN (LINE 11/12 Input) Jacks Permit you to either include externally generated effects (such as a digital sampler or synth) IN the mix, or to process the mixed sound (echo reverb, etc.). Use two 1/4" (TRS) jacks of LINE 11/12 as effect return path, turn the EFX GAIN of CH 11/12 fully down to avoid undesirable feedback. LINE 1, LINE 2, LINE 3, & LINE 4 BAL or UNBAL 1/4" (TRS) Input Jack For connecting a balanced or unbalanced line level sources. MIC1/MIC2/MIC3 & MIC4 Balanced XLR Input Connector For connecting a balanced low impedance microphone with XLR type plug. LINE 5/6, LINE 7/8, LINE 9/10, & LINE 11/12 BAL or UNBAL 1/4" (TRS) Input Jacks For connecting a balanced or unbalanced stereo line level sources. Use LEFT input jack only for each channel, if the source signal is mono. CTRL ROOM OUT Jacks To connect the mixer to a second receiver or amplifier powering speakers in the control room or in a remote location. HEADPHONES Jack Accepts the headphones with 1/4" plug. POWER ON Indicator MIC1/LINE 1, MIC2/LINE 2, MIC3/LINE 3, & MIC4/LINE 4 GAIN Control Lets you adjust the gain of the input source. MAIN OUT Jacks To connect the mixer to a receiver or amplifier. CH1, CH2, CH3, & CH4 Tone Controls (EQ) TAPE IN & OUT Jacks To connect the mixer to a tape deck for recording the mixed program and for auditioning mix playback from tape. TAPE TO MIX Switch Press to route the signal playback from tape to the MAIN mix bus. EFX TO CONTROL ROOM Switch Press to route the EFX SEND signal to the control room. DUAL LED DISPLAY METER Indicates the levels of left and right MAIN outputs. PHANTOM +48V DC Switch with Indicator Press to accept the use of condenser microphones. MASTER Level Control Lets you adjust the signal level of MAIN and TAPE outputs. EFX SEND Level Control Lets you adjust the EFFECTS signal level sent to the EFX SEND. CONTROL ROOM/PHONES Level Control Lets you adjust the signal level sent to the control room and headphones. TAPE TO CONTROL ROOM Switch Press to route the signal playback from tape to the control room. CH5/6, CH7/8, CH9/10, & CH11/12 BAL Control Lets you adjust the channel signal levels of left and right relative to each other before both signals are then sent to the MAIN mix bus. It allows you to balance the source in the stereo image. CH1, CH2, CH3, CH4, CH5/6, CH7/8, CH9/10, & CH11/12 EFX Control Lets you adjust the channel signal level sent to the external effect. CH1, CH2, CH3, & CH4 PEAK Indicator Indicates the channel signal is going into overload. CH1, CH2, CH3, & CH4 LO CUT Switch Press to eliminate unwanted low-frequency signal components. CH5/6, CH7/8, CH9/10, & CH11/12 GAIN Switch Press to increase the channel gain by +12dB. CH1, CH2, CH3, CH4, CH5/6, CH7/8, CH9/10, & CH11/12 LEVEL Control Lets you adjust the channel signal level sent to the MAIN mix bus. CH1, CH2, CH3, & CH4 PAN Control Lets you adjust the channel signal level feeding the L & R mix bus. Pyle Pro Mixer PYD6070/1270 Owner's Manual ­ 3 INSTALLATION, PYD6070 Mixers 4 ­ Pyle Pro Mixer PYD6070/1270 Owner's Manual INSTALLATION, PYD1270 Mixers Pyle Pro Mixer PYD6070/1270 Owner's Manual ­ 5 Mono Input Channel Controls CH1/CH2 For PYD6070 CH1/CH2/CH3/CH4 For PYD1270 MIC Each mono input channel comes with an XLR balanced microphone input connector and also offers a +48V PHANTOM switch to supply power for condenser microphones. Please mute the playback/PA loudspeakers system before switching on +48V PHANTOM power to prevent the switchon thumps being directed to the loudspeakers. Please connect the microphones before switching on the +48V PHANTOM power supply, do not connect microphones to the mixer as long as the phantom power supply is switched on. Wait for approximately one minute to get the system stabilized. EQ (HI/MID/LO) ALL the mono input channels has a 3-band equalizer, all bands provide up to 15dB of cut and boost, with a centre detent for OFF. The cut-off frequencies of HI and LO band are 10 kHz and 100 Hz respectively. The MID band is configured as a peak filter with a center frequency at 1 kHz . EFX It enable you to feed channel signal to the external effect. PAN It determines the amount of the channel signal feeding the left and right mix bus, to locate the source smoothly across the stereo image. Its constant-power design ensure the signal is always maintained at a constant level. LINE Each mono input channel comes with a balanced 1/4" (TRS) line level input jack. The unbalanced devices can also be connected to this input. PEAK It illuminates to warm you the input channel signal is driven too high, which could cause distortion. Use the GAIN control to adjust until the LED does not light. NOTE Please use only either the MIC or LINE input of a channel at any one time, do not use both simultaneously. GAIN This rotary GAIN control adjusts the channel input gain level. Proper gain setting gives the mixer to work in the best operating level. Please turn it to 0 completely whenever you connect or disconnect a signal source to one of the inputs. LEVEL It determines the level of channel signal in the MAIN mix bus and provides a clear visual indication of channel level. LO CUT (PYD1270) It is a steep LO CUT filter designed to eliminate unwanted low frequency hum. It is useful on live vocals to reduce stage rumble or "popping" noise from microphone. 6 ­ Pyle Pro Mixer PYD6070/1270 Owner's Manual Stereo Input Channel Controls CH3/4 & CH5/6 For PYD6070 CH5/6, CH7/8, CH9/10 & CH11/12 For PYD1270 LINE, LEFT & RIGHT Each stereo input channel comes with two balanced 1/4" (TRS) line level input jacks. The unbalanced devices can also be connected to this input. If only the jack marked "LEFT" is used, the channel operate in mono. The stereo channels are designed to handle typical line level signals. BAL It determines the level of left and right input signals relative to each other before both signals are then routed to the MAIN stereo mix bus, allows you to balance the source in the stereo image. If a stereo channel is run in mono (only the left input connected), the balance control acts as a pan in the normal way. EQ (PYD6070) It is similar to those of the mono channels, except that the EQ is stereo. It is preferable of using two mono equalizer when EQ-ing a stereo signal to avoid the discrepancies occurred oftenly between left and right setting. LEVEL It determines the level of channel signal in the MAIN mix bus and provides a clear visual indication of channel level. GAIN (PYD1270) It is an input sensitivity switch which used to select between +12dB (press on) for studio level and 0dB (press off) for home-recording level. EFX It is similar to those of the mono channels, except that the EFX SEND buses are both mono, a mono sum is first taken from the stereo input before it is sent to the EFX bus. Pyle Pro Mixer PYD6070/1270 Owner's Manual ­ 7 Main Section Connections and Controls PYD6070 PYD1270 EFX SEND Jack It is a 1/4" unbalanced jack sends out the signals from mix bus to the external effects unit. EFX RETURN Jacks/Control (PYD6070) The EFX RETURN Jacks bring the output of the external effects unit back into the mixer. These jacks can be used instead as additional line level inputs, but any external effects signal will have to be brought back into the mixer via a normal stereo channel, it does allow you to use the channel EQ on the effects return signal. When a normal stereo channel is used as effects return path, the EFX control of the relevant channel should be turned fully down to avoid undesirable feedback. If only the LEFT jack is used, the EFX RETURN is operated in MONO mode. Use the EFX RETURN rotary control to adjust the effects signal levelsent to the MAIN mix bus. NOTE:PYD1270 uses two 1/4" (TRS) jacks of LINE 11/12 as EFX RETURN, turn the EFX GAIN of CH 11/12 fully down to avoid un ...