User manual PYLE PYX3X

Electronic Crossover Network Please complete warranty card, detach and return Thank you for purchasing this PYLE product. To activate your warranty, please mail this card within 10 days. warranty registration card Name Address City, State ZIP PYLE PRO ELECTRONICS Model No. Date of Purchase Purchased at: Music Products Store Catalog Merchandiser Serial # (if available) Sound Contractor/Installer Other Mail Order Owner's Manual PYX-3X Your new Pyle Pro PYX-3X Electronic Crossover Network is designed to enable the home stereo audiophile to install a biamp, triamp or multi-amp system with extreme ease, while still allowing for the sophisticated settings a high end installation demands. The PYX-3X permits frequency filtering in four different bands: LOW, MID/HIGH PASS, MID/LOWPASS and HIGH. It also offers the user the opportunity to adjust output levels for LOW, MID and HIGH independently. Input and output connections may be made via a choice of 1/4" or RCA type jack, permitting a connection with almost any input or output device. Please read this manual thoroughly before you attempt to set up and use this crossover. It contains a range of installation suggestions as well as instructions to ensure safe usage. Installed properly, you can expect years of trouble-free service from this product. REAR PANEL FEATURES AND CONTROLS L INPUT HIGH OUTPUT MID INPUT LOW HIGH OUTPUT MID FUSE LOW L L L R FRONT PANEL ELECTRONIC CROSSOVER NETWORK PY X-3X R R R LOW PASS 50 90 180 50 90 360 720 180 1K 2K 360 720 FLAT 4K 6K 8K FLAT 1K 2K 4K 6K 8K LOW LEVEL MID LEVEL HIGH LEVEL POWER LOW MID MID HIGH Ground Screw MIN MAX MIN MAX MIN MAX LOW PASS HIGH pass LOW PASS HIGH PASS Fuse Holder Left and Right Output Connectors The PYX-3X offers a choice of 1/4" or RCA type Left and Right Output jacks (for LOWS, MIDS and HIGHS) for connecting to the inputs of your power amplifier(s). Power On/Off Crossover Freqency Selectors Selects the crossover point for each of the frequency ranges: LOW PASS selects the crossover point between the bass and midrange MID/HIGHPASS selects the low end of frequency range for the MIDS MID/LOWPASS selects the high end of frequency range for the MIDS HIGHPASS selects the low end of frequency range for the HIGHS Volume Controls Adjusts the output levels for the LOWS, MIDS and HIGHS Left and Right Input Connectors The PYX-3X offers a choice of 1/4" or RCA type input jacks for connecting to the PREAMP OUTS of your audio source. i ­ PYLE PRO PYX-3X Electronic Crossover Network Owner's Manual PYLE PRO PYX-3X Electronic Crossover Network Owner's Manual - 1 INSTALLATION GUIDELINES Input connections The PYX-3X accepts a broad range of input sources, including: Compact Disc (CD) player Cassette, Reel-to-Reel or other tape player Radio Tuner These can be connected via either 1/4" or RCA type jacks to the input jacks on the rear panel of the PYX-3X. Setting the frequency controls Biamp Systems In a biamp system, the frequency ranges are usually LOWS (with a range of about 40Hz to 120Hz), and MIDS/HIGHS (with a range from 120Hz to about 20KHz). Settings for such a system would be something like this: Triamp Systems In a triamp system, the frequency ranges are usually LOWS (with a range of about 40Hz to 120Hz), MIDS (with a range from 120Hz to about 5-8KHz) and HIGHS (with a range from 5Hz to about 20KHz). The PYX-3X uses the two MIDS frequency controls together to form a bandpass section for the MIDS range, with one control setting the lower and one setting the upper crossover points. Settings for such a system would be something like this: INPUT HIGH OUTPUT MID INPUT LOW HIGH OUTPUT MID Output connections for Triamp Systems A typical triamp home system might consist of a 4-Channel amp for reproduction of MIDS and HIGHS, and a separate 2-Channel amp for reproduction of LOWS (a similar result can be obtained using separate 2-channel amps for each of the LOW, MID and HIGH ranges). NOTE: These diagrams show hookups using the RCA type jacks, but you can use the 1/4" jacks instead with similar results. 50 90 LOW PASS 180 50 90 360 720 180 1K 2K 360 720 FLAT 4K 6K 8K FLAT iK 2K 4K 6K 8K CD PLAYER, TAPE PLAYER RADIO TUNER LOW MID MID HIGH FUSE LOW LOW PASS HIGH pass LOW PASS HIGH PASS LOW PASS 50 90 180 50 90 360 720 180 1K 2K 360 720 FLAT 4K 6K 8K FLAT iK 2K 4K 6K 8K L L L L R R R R Upper end, MIDS/HIGHS range: Flat (range not affected) Lower end, MIDS/HIGHS range: 120Hz Upper end, LOWS range: 120Hz INPUT HIGH OUTPUT MID INPUT LOW HIGH OUTPUT MID LOW MID MID HIGH LOW PASS HIGH pass LOW PASS HIGH PASS FUSE LOW L L L L R R R R Input connections using RCA jacks Output connections for a biamp system A typical biamp system employs a 4 channel amplifier, with one pair of channels used to handle MIDS/HIGHS, with the second pair of channels handling the LOW frequencies. A similar system can be built using separate amplifiers to handle the two frequency ranges. This kind of setup would be accomplished as follows: Lower end, HIGHS range: 5KHz Upper end, MIDS range: 5KHz Lower end, MIDS/HIGHS range: 120Hz Upper end, LOWS range: 120Hz AMP CH 1 + 2 INPUTS AMP CH 3 + 4 INPUTS (HIGHS CHANNEL) (MIDS CHANNEL) 4 CH AMPLIFIER CD PLAYER, TAPE PLAYER RADIO TUNER Note: Only LOWS and MIDS output jacks are used for connections in a biamp installation! NOTE: These diagrams show hookups using the RCA type jacks, but you can use the 1/4" jacks instead with similar results. FUSE INPUT HIGH OUTPUT MID INPUT LOW HIGH OUTPUT MID LOW L L L L R R INPUT HIGH OUTPUT MID INPUT LOW HIGH OUTPUT MID R R FUSE LOW L L L L R HIGH OUTPUTS MID OUTPUTS SUBWOOFER AMP INPUTS (LOWS CHANNEL) 2 CH AMPLIFIER R R R Input connections using 1/4" jacks AMP CH 1 + 2 INPUTS (MIDS/HIGHS CHANNEL) AMP CH 3 + 4 INPUTS (LOWS CHANNEL) 4 CH AMPLIFIER LOW OUTPUTS MID/HIGH OUTPUTS LOW OUTPUTS 2 ­ PYLE PRO PYX-3X Electronic Crossover Network Owner's Manual PYLE PRO PYX-3X Electronic Crossover Network Owner's Manual - 3 Please complete warranty card, detach and return Mounting the PYX-3X The PYX-3X is designed to accept standard rack mounting installations. Two slots on each end of the front panel make it suitable for such an installation. Tightly secure four mounting screws (not supplied) through these fours slots and into your standard electronics equipment rack. Crossover Frequencies Low 50, 90, 180. 360 and 720 Hz Mid (High Pass) 50, 90, 180. 360, 720 Hz and Flat Mid (Low Pass) 1K, 2K, 4K, 6K, 8KHz and Flat High 1K, 2K, 4K, 6K and 8KHz Filter Slope Total Harmonic Distortion Frequency Response S/N Ratio Power Requirement Power Consumption Dimensions, inches (mm) -12dB/Octave <0.01% 20 Hz - 20KHz (+/- 0.5 dB) 90 dB AC 110V/60Hz or 230V/50Hz 6W 18 7/8 x 2 3/8 x 7 7/8 (180 x 60 x 200) Turning the PYX-3X on 1. Turn on the audio input source equipment which is connected to the PYX-3X INPUT jacks. 2. Set the LOW, MID and HIGH volume level controls to their minimum level settings. 3. Adjust the crossover frequency points to suit your audio system installation. 4. Push in the power switch to turn the amplifier on. 5. Adjust the LOW, MID and HIGH volume level controls to the desired volumes. Limited Warranty All PYLE PRO products are carefully constructed and tested before shipment. Units purchased in the USA are warranted to be free of defects in material and workmanship for two (2) years from the date of purchase. This warranty is limited to the original retail purchaser of the amplifier. Should the unit fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of PYLE. To obtain warranty service, you must first call our Consumer Return Hotline at (718) 236-6948 to obtain a Return Authorization Number. This R.A. # must appear on the outside of your package and on all paperwork relating to your return. When returning the unit to us for warranty service, it must be carefully packed and shipped, prepaid, to: R.A.#: _____________ PYLE PRO Service Center 1600 63rd Street Brooklyn, NY 11204 You must also include the following items with your return: · A copy of your sales receipt or other proof of purchase · A brief letter, indicating the problem you are experiencing with the product · Include in your letter your return address, daytime phone number and R.A. number · Also include a check or money order for $15.00 for return shipping, handling and insurance, or provide your Visa/MC number with expiration date. Our obligation under this warranty is limited to the repair or replacement of the defective unit when it is returned to us prepaid. This warranty will be considered void if the unit was tampered with, improperly serviced or subject to misuse, neglect or accidental damage. Caring for your PYX-3X Electronic Crossover Network This component uses a 250V 0.5A fuse for protection from power surges and short circuits. If the unit suddenly shuts down and will not turn on, it is likely that this fuse has blown. To replace the fuse: 1. Locate the fuse holder on the rear of the cabinet and unscrew the fuse compartment cap. 2. Remove the old fuse and replace it with an identical, serviceable fuse. CAUTION! Never use a fuse with a higher rating! 3. Replace the fuse compartment cap. 4 ­ PYLE PRO PYX-3X Electronic Crossover Network Owner's Manual PYLE PRO PYX-3X Electronic Crossover Network Owner's Manual - 5 PYLE PRO Audio, Inc. 1600 63rd Street Brooklyn, NY 11204 Connecting to standard AC power After making all other connections, set the POWER switch to OFF position. Then connect the power cord to a standard AC outlet. PYX-3X Specifications Input Impedance >47 K-Ohms Place Stamp Here