1675 MacArthur Blvd., Costa Mesa, CA, 92626 USA Main Number (714) 754-6175 or toll free (USA only) (800) 854-4079 Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834 ALK-MD2 Array Link Kit for Two MD-series Loudspeaker Enclosures This kit is to be used only for arraying of two QSC MD series loudspeaker enclosures, active or passive. Do not use this kit or any component of this kit for any other purpose. Contents: ·Array link, AL-MDR2 ·Array link, AL-MDF ·Bolt, hex, cap, 3/8"-16TPI x 1.5", grade 5 ·Washer, flat, 7/16" x 1" , .07" - .09" thick ·Washer, lock, internal tooth, 3/8" ·Eyebolt, 3/8"-16TPI x 1.5" 2 each 2 each 8 each 14 each (3 are spares) 14 each (3 are spares) 3 each Rules for Suspension · Correct use of all suspension hardware and components is imperative in sound system rigging and deployment. · Always calculate suspended loads before lifting to ensure suspension components and hardware are used within their respective load limits. · Research local codes and regulations to fully understand the requirements for suspended loads in the venue in which the equipment is to be suspended. · Be absolutely certain of the integrity of any structural member intended to support suspended loads. Hidden structural members can have hidden structural weakness. · Consult a professional mechanical or structural engineer licensed in the jurisdiction of the sound system installation to review, verify, and approve all attachments to the building or structure. · Never assume anything- owner or third-party supplied suspension attachment points may not be adequate for the loads to be suspended. · Employ the services of a professional rigger for hoisting, positioning, and attaching the equipment to the supporting structure. · Always inspect all components (enclosures, suspension brackets, pins, frames, bolts, nuts, slings, shackles, etc.) for cracks, wear, deformation, corrosion, missing, loose, or damaged parts that could reduce the strength of the assembly before lifting. Discard any worn, defective, or suspect parts and replace them with new appropriately load-rated parts. Shock Loading When a load is either moved or stopped, its static weight is magnified. Sudden movements can magnify the static weight several times. This magnification of static weight is termed "shock loading". Shock loading poses a danger to equipment and workers. The effects of shock loading can be instantaneous, or they may remain undetected unless the equipment is visually damaged. Avoiding shock loading requires careful planning and knowledge of equipment, rigging, and lifting practices. · Shock loading of equipment and structures is usually confined to lifting and installation, but natural forces (winds, earthquakes) can impose shock loads several times the static load. This is why structures and suspension equipment must be capable of supporting several times the weight of the equipment suspended. Working Load Limits Component MD-F, MD-L, MD-FP, and MD-LP loudspeakers, top and side panel suspension points MD-F, MD-L, MD-FP, and MD-LP loudspeakers, rear panel suspension points Eyebolt Weight 90 lb (40.8 kg) n/a 7:1 Design Factor 457 lb (207.3 kg) 314 lb (142.4 kg) 857 lb (388.7 kg) 10:1 Design Factor 320 lb (145.2 kg) 220 lb (99.8 kg) 600 lb (272.2 kg) 12:1 Design Factor 267 lb (121.1 kg) 183 lb (83.0 kg) 500 lb (226.8 kg) n/a *TD-000242-00* TD-000242-00 revA Installation Instructions 1. Orient the enclosures with their bottoms pointing upward and the required splay angle. 2. Remove the factory-installed screws from the enclosures where the bolts are to be installed for the ALK-MD2 kit. 3. Set the rear (AL-MDR2) and front (AL-MDF) links on the enclosures and position the assembly until the mounting holes line up at the required splay angle. 4. Assemble a lock washer, then a flat washer, onto each bolt. Put the bolt assembly through the selected mounting hole in the array link and thread the bolt into the enclosure's threaded insert. Tighten fully. 5. Carefully turn the array over, ensuring not to stress the links previously installed. Repeat steps 2 - 4 for the top surface of the enclosures. 6. For a vertically oriented array, install two eyebolt assemblies; one on each enclosure's top surface, outermost front threaded insert. Ensure each eyebolt has a lock washer, then a flat washer installed before threading into the enclosure. Tighten eyebolts fully. Use the lower rear array link for pull back. 7. For a horizontally oriented array, install two eyebolts on the side of the enclosure that will become the top of the array. A third eyebolt should be used on the back of the lower enclosure of the array for setting downtilt angle and stabilization. Figure 1- Vertically oriented array and hardware assembly order. Figure 2- Horizontally oriented array. Note eyebolt installation locations. Figure 3- Minimum splay angle example. Figure 4- Maximum splay angle example. © Copyright 2007, QSC Audio Products, Inc. QSC® is a registered trademark of QSC Audio Products, Inc. "QSC" and the QSC logo are registered with the U.S. Patent and Trademark Office All trademarks are the property of their respective owners.