OPERATORS MANUAL TTM 56 PERFORMANCE MIXER MIC 4 2 0 10 6 8 OFF +6 2 0 10 PGM 1 4 6 8 2 0 10 4 6 PGM 2 4 8 OFF +6 2 0 10 6 8 Quick Start Congratulations! You are the proud owner of an exceptional performance instrument. Experienced turntablists will find the TTM 56 comfortable and familiar. The TTM 56 has many unique features which are mastered quicker if you read the manual. Right! We know you can't resist jumping right in, but please read at least this portion of the manual. It will help you get a good start. About the Faders: The Channel Faders and Crossfader are magnetic, non-contact Faders. This means No travel noise ­ No bleed ­ Ever! The electrical performance of the Faders is unaffected by use. Old habits are hard to break, but you really don't have to mess with the Faders. The magnetic Faders in this mixer are very different from what you are used to. Be sure and read the Q and A section on page Manual-10. LEVEL OL HIGH GAIN GAIN HIGH MASTER 4 2 6 8 0 10 -12 +12 OFF +6 EQ EQ OFF +6 HIGH MID MID AUX OUT 4 2 6 8 0 10 -12 +12 OFF +6 FlexFX FlexFX OFF +6 LOW LOW LOW PHONES LEVEL 4 2 0 6 8 10 L PAN R DRY WET L PAN R MASTER / CUE AUX IN TTM 56 PERFORMANCE MIXER CHANNEL REVERSE PGM 1 CUE PGM 2 REVERSE MODE 1 MODE 2 REVERSE TRANSFORM TRANSFORM MODE 1 MODE 2 FAST MONO PGM1 / PGM2 STEREO HOUSE FAST CONTOUR +10 +7 CONTOUR SLOW SLOW Special Features: · Channel Fader MODE switches allow selecting two sets of curves: MODE 1 gives the familiar stereo fader response. MODE 2 gives a left/right pan effect. · Both curves allow continuous adjustment of CONTOUR, giving smooth blend or fast cut. A B · The CHANNEL REVERSE switch allows the left-hand or right-hand Fader to control PGM 1 or PGM 2. · The CROSSFADER MODE switch allows selecting two sets of curves: MODE 1 gives the familiar PGM 1 to PGM 2 cross-fade response. MODE 2 gives a center cut response (PGM 1 and PGM 2 are off in the center). · Independent CONTOUR controls for each side of the Crossfader allow cut on one side and blending on the other (or any combination). · Auxiliary Inputs and Outputs, with independent level controls, give session mixing ability. AUX Inputs may be used for drum machine, tape, etc. AUX Input is after the Crossfader and after the Effects loop. AUX Outputs may be used for recording, booth monitoring, or a second zone. AUX Output is the same as the Master Mix. · FlexFXTM allow assignment of PGM 1, PGM 2 or both to the effects loop. The effects loop is post-fader. You get great results when using the Channel Faders or Crossfader with reverb or other delay effects. WET/DRY pan lets you control how much effect is in the mix. · Three-band Accelerated-SlopeTM EQ allows full cut of each band. The EQ engage switch lets you A/B compare or quickly transform the EQ effect. · Two, 10-segment meters provide dual-mono-Cue or stereo-Master operation. · Yes, we included a power switch on the rear. The flexibility of the TTM 56 Faders can result in some initial confusion. We highly recommend trying one thing at a time. This helps avoid initial confusion. Make sure the Channel reverse switch is off. Start by changing the Mode and Contour of each fader, one at a time. See the diagrams on pages Manual-6-7 to understand the fader responses under different settings. Once you understand the controls, start creating! +2 0 -2 -4 -7 -10 -20 REVERSE MODE 1 MODE 2 +4 WEAR PARTS: This product contains the following wear parts subject to the ninety (90) day warranty period described on page Warranty-1: ST 2 Phono/Line Switch Assembly (2). Manual-1 Rear Panel Hook-up TTM 56 N108 CLASS 2 EQUIPMENT MADE IN U.S.A. RANE CORP. U.S. PATENT PENDING PHONO GND MASTER OUT AUX OUT L POWER L IN FlexFX RETURN L SEND MIC BAL INPUT PGM 2 LINE 2 L PHONO 2 PGM 1 LINE 1 L EFFECTS PHONO 1 R R 750mA R R R BALANCED UNBALANCED TIP = SEND RING = RTRN Inputs PGM 1 and PGM 2 each have stereo PHONO and stereo LINE inputs. PHONO 1 and PHONO 2 inputs are RIAA compensated inputs, for turntables only! PHONO GND terminals provide independent ground connect points for turntables. It is very important that each turntable have a very good ground connection to one of these terminals. The thumbscrews will come off if they are over-rotated, so be careful not to spin them off and lose them. LINE 1 and LINE 2 inputs are unbalanced line-level inputs with a sensitivity of -10 dBV (max gain). AUX INPUT may be used with a drum machine, groovebox, sampler, or another mixer's output for session mix. This Input is mixed after the Crossfader and Effects loop. MIC INPUT is a balanced input specifically designed for a dynamic microphone. Power POWER connector. This is not a telephone jack! Connect only the Rane RS 1 power supply included with your TTM 56. The POWER switch is located just above the power connector. You know what to do with this one, but leave it off until everything is connected. Effects Loops MIC EFFECTS insert jack is unbalanced. It is wired for TRS, Tip=Send, Ring=Return. This is an independent Effects Loop for the Mic. There is no engage switch, so the Mic signal is always processed when you have an effects box connected. If you are connecting to an effects processor with a Send/Return jack, a single TRS cable will work. If your effects processor has separate Send and Receive jacks, you need a "Y" cable. You can buy a Send/Return cable from your local music store, or you can make one of your own, as shown below. FlexFX EFFECTS jacks are unbalanced mono ¼" TS (Tip/Sleeve). This stereo loop is used for output to (send) and input from (return) an effects processor. The SEND jacks provide the output to your effects processor. The RETURN jacks provide input for the signal returning from your effects processor. To use with effects insert devices with a single TRS, tip=send, ring=return jack, you need a "Y" cable, as shown below. RED 1-CONDUCTOR SHIELDED CABLE RED SHIELD T = SEND R = RETURN S = SHIELD SEND RED SHIELD 1-CONDUCTOR SHIELDED CABLE RED SHIELD RETURN Send/Return Cable Wiring Manual-2 Outputs AUX OUT may be used for recording, booth monitoring, a second zone, or for connecting to another mixer for session mix. AUX OUT is the same as the Master Mix with independent Level control. MASTER OUT includes two sets of stereo outputs: The ¼" TRS jacks provide high current balanced (Tip-Ring-Sleeve) output. Use the balanced output whenever driving equipment with a balanced input, or when running distances greater than 10 feet (3 meters). Due to the high drive capability and low impedance, never use a mono ¼" Tip/Sleeve (no ring) plug in this jack. Use the RCA unbalanced outputs for shorter runs connecting to unbalanced devices. See RaneNote 110 if you need to convert between balanced and unbalanced or run long distances. Mic Section MIC LEVEL sets the gain of the Mic Input. The range of operation is OFF to +50 dB. There is no engage switch, so set the MIC LEVEL to zero (0) when not in use. The OL indicator lights 6 dB before clipping. Adjust MIC LEVEL so the OL indicator flashes only when you shout into the mic. MIC HIGH and LOW tone controls provide as much as 12 dB of boost or 12 dB of cut. These controls have no effect when the controls are set to their center detent (12 o'clock). MIC 4 2 0 10 6 8 OFF +6 2 0 10 PGM 1 4 6 8 2 0 10 4 6 PGM 2 8 OFF +6 LEVEL OL HIGH GAIN GAIN HIGH -12 +12 OFF +6 EQ EQ OFF +6 HIGH MID MID -12 +12 OFF +6 FlexFX FlexFX OFF +6 LOW LOW LOW 4 2 0 6 8 10 L PAN R DRY WET L PAN R AUX IN Program and Aux Input Section PGM 1 inputs are sent to the left side of the Crossfader. (with the REVERSE switch out) PGM 2 inputs are sent to the right side of the Crossfader. (with the REVERSE switch out) AUX INPUT adds another line-level input to the mix. This input comes in after the Crossfader and FlexFX Loop. GAIN controls adjust the signal level before it gets to the Faders. Set the GAIN controls to indicate an average signal level of +4 on the meter with the Program Faders set to maximum. Don't use the GAIN controls to set the output level...use the MASTER LEVEL control to set the output level. This is a very simple thing, yet makes a huge difference in the performance of your mixer. EQ switches engage the 3-band tone controls. EQ switches may be used in conjunction with the Hi, Mid and Low controls as "kill" switches. Set the rotary controls and flip the switch. HIGH tone controls affect frequencies above 4 kHz. The range of control is +6 dB to OFF (full kill). The center detent position leaves this filter inactive. This filter is just above the vocal range, and can make small tonal changes, or eliminate high frequency signals. MID tone controls affect frequencies from 300 Hz to 4 kHz (vocal midrange). The range of control is +6 dB to OFF (full kill). The center detent position leaves this filter inactive. Use for small tonal changes or to cut midrange signals. LOW tone controls affect frequencies below 300 Hz. The range is +6 dB to OFF (full kill). The center detent position leaves the filter inactive. These filters influence signals below the vocal range. Use to adjust or eliminate bass beats. PAN controls adjust the Left and Right balance of PGM 1 and PGM 2. Don't use these excessively for left/right pan effect, they are not as durable as the Faders. For left/right pan effect, use the Channel Faders in Mode 2. Manual-3 CHANNEL REVERSE switch allows the left-hand or right-hand Fader to alternately control PGM 1 or PGM 2. (Don't confuse with the Channel Fader REVERSE switch, see below.) TRANSFORM switches provide two functions: · PHONO / LINE source selection for PGM 1 and 2. · Quick cut between the used and unused input. The switches are easily field replaceable and may be rotated in 45° increments. See page Manual10 for instructions. TTM 56 PERFORMANCE MIXER CHANNEL REVERSE REVERSE MODE 1 MODE 2 TRANSFORM TRANSFORM FAST MONO PGM1 / PGM2 STEREO HOUSE CONTOUR +10 +7 +4 +2 SLOW Faders The Channel Faders and Crossfader are magnetic, noncontact Faders. This means No travel noise ­ No bleed ­ Ever! The electrical performance of the Faders is unaffected by use. The Channel Faders and Crossfader each have their own CONTOUR, REVERSE (hamster) and MODE controls. Magnetic Faders are very different from what you are used to. Read Maintaining Magnetic Faders on pages Manual 89, and the Magnetic Fader Q & A section on page Manual10. Channel Fader MODE switch: Channel Fader Mode switches allow selecting two sets of curves. MODE 1 gives the familiar stereo fader response. MODE 2 gives left/right pan effect. Channel Fader CONTOUR controls allow smooth, continuous adjustment of contour for both MODE 1 and MODE 2. The range of control is from SLOW blend to FAST cut. Channel Fader REVERSE switches change the direction of the channel Faders. When the reverse switch is engaged, up is down and down is up (hamster). CROSSFADER MODE switch allows selecting two sets of curves for the Crossfader. MODE 1 gives the familiar PGM 1 / PGM 2 crossfade response. MODE 2 gives a center cut response (PGM 1 and PGM 2 off in the center). CROSSFADER CONTOUR A & B provide Independent Contour controls for each side of the Crossfader. This allows a fast cut on one side and slow blending on the other (or any combination you choose). A 0 -2 -4 -7 -10 -20 REVERSE MODE 1 MODE 2 B Meters Meters provide switchable true stereo Master Mix or dual-mono PGM1 / PGM2 indication of Pre-Program Fader signal levels. Ten-segment resolution is provided with a one second, peak hold. Use the meter to set the GAIN controls. With the Program Fader set to maximum, the input GAIN should be set to indicate an average level of about +4 dB. CONTOUR A CROSSFADER REVERSE MODE CONTOUR B Manual-4 FlexFX Loop FlexFX switches send PGM 1, PGM 2 or both to the stereo effects loop. The effects loop is post-Fader and post-Crossfader. You get great results when using the Channel Faders or Crossfader with reverb or other delay effects. The effects loop provides separate stereo send and return jacks. The green indicators light when FlexFX is engaged. WET/DRY pan control lets you set the amount of effect in the mix. DRY equals no effect, WET gives maximum effect. Output Section MASTER control sets the level for both the unbalanced and balanced Master Outputs. AUX OUTPUT control sets the level of the Auxiliary Outputs. 2 4 6 8 0 10 Headphone Cueing The headphone amp in the TTM 56 has a high power output (unlike most you have used before). There are notable differences... · The headphone output of the TTM 56 delivers very high volume to your headphones. · To avoid pain, never put headphones on your head before plugging them in. · Always start with the PHONES LEVEL turned down, and then turn it up to the desired level. 2 2 MASTER 4 6 8 0 10 AUX OUT 4 6 8 0 10 · Because of the high current and low output impedance, never short one side to gr ...