DSM300 & DSM30 Digital Sounder Module Installation Manual Document number: 87080-1 Date: November 2006 Trademarks and registered trademarks HSB, Raymarine and SeaTalk are registered trademarks of Raymarine plc. All other product names are trademarks or registered trademarks of their respective owners. Contents of this handbook ©Raymarine 2006 3 Contents Trademarks and registered trademarks ............................................ 2 Important Information .........................................................................................5 Intended Use .......................................................................................... 5 Safety Notices ...................................................................................... 5 EMC Conformance ................................................................................. 6 Declaration of Conformity ................................................................ 6 Product Disposal .................................................................................... 6 Waste Electrical and Electronic Equipment (WEEE) Directive ........... 6 Warranty .............................................................................................. 6 Chapter 1: DSM Installation ..............................................................................7 1.1 Introduction ........................................................................................... 7 Planning the Installation ........................................................................ 7 EMC Installation Guidelines ................................................................. 7 Suppression Ferrites ......................................................................... 8 Connections to Other Equipment ..................................................... 8 1.2 Unpacking and Inspecting the Components ........................................... 9 Cable Options ...................................................................................... 10 1.3 Selecting Sounder Module Mounting Location .................................... 10 1.4 Mounting the Sounder Module ........................................................ 11 1.5 Cable Runs ......................................................................................... 14 1.6 System Connections ........................................................................... 14 Transducer Connection ...................................................................... 15 DC Power Connection ........................................................................ 15 Ground Connection ............................................................................ 18 1.7 Display Configuration ...................................................................... 18 Configuring E Series Displays ............................................................. 18 Configuring C Series Displays ............................................................. 19 Configuring hsb2 PLUS (Pathfinder) Series Displays ........................... 20 Chapter 2: Maintenance and Problem Solving ...............................................21 2.1 Maintenance ........................................................................................ 21 Routine Checks .................................................................................... 21 Cleaning Instructions ........................................................................... 21 EMC Servicing and Safety Guidelines ................................................... 22 2.2 Resetting the System ............................................................................ 23 For E Series and C Series Displays... ................................................ 23 For hsb2 PLUS Series Displays... ..................................................... 23 2.3 Problem Solving ................................................................................... 25 Common Problems and Their Solutions ................................................ 25 Status LED .......................................................................................... 26 4 DSM300 and DSM30 Installation Manual 2.4 How to Contact Raymarine ...................................................................28 On the Internet .....................................................................................28 Customer Support ..........................................................................28 In the US ...............................................................................................28 Accessories and Parts .....................................................................28 Technical Support ...........................................................................29 Product Repair and Service .............................................................29 In Europe ..............................................................................................30 Technical Support ...........................................................................30 Accessories and Parts .....................................................................30 Worldwide Support ..............................................................................30 Appendix: Specifications...............................................................................31 General .................................................................................................31 Sounder Features ..................................................................................31 Index ......................................................................................... 33 5 Important Information Raymarine DSM300 and DSM30 Digital Sounder Modules provide echo sounder data that can be displayed on Raymarine E Series, C Series, and hsb2 PLUS (Pathfinder) Series display units. This manual contains important information for installing and maintaining your Digital Sounder Module. Raymarine's Technical Services representatives or your local dealer will be available to answer any questions you may have. Instructions on how to operate the fishfinder application can be found in the handbook for your particular display system. Intended Use DSM300 and DSM30 Digital Sounder Modules are intended for depth finding and fishfinding purposes on recreational (non-IMO/SOLAS class) boats. Echo sounders require an appropriate Raymarine transducer and interconnecting cable. Safety Notices This equipment must be installed and operated in accordance with the instructions contained in this manual. Failure to do so can result in personal injury and/or navigational inaccuracies. In particular: CAUTION: High Voltage Digital Sounder Modules contains high voltages. Adjustments require specialized service procedures and tools only available to qualified service technicians ­ there are no user serviceable parts or adjustments. The operator should never remove the cover or attempt to service the equipment. CAUTION: Transducer Cable Removing the transducer cable from the rear of the DSM300 or DSM30 while the sounder module is powered on can cause sparks. Only remove the transducer cable after power has been removed from the DSM. As with any electronic device, be sure the sounder module is mounted where it is well ventilated and free from gasoline fumes. If the transducer cable is accidentally removed while the DSM is powered on, remove power from the sounder module, replace the transducer cable, and then return power to the module. As a safety feature, the sounder module only recognizes that the transducer is connected at power-up. 6 DSM300 and DSM30 Installation Manual EMC Conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. The design and manufacture of Raymarine equipment and accessories conform to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised. Declaration of Conformity Raymarine plc declare that the DSM300 and DSM30 Digital Sounder Modules are in compliance with the essential requirements of EMC directive 2004/108/EC. The original Declaration of Conformity certificate may be viewed on the relevant product page at www.raymarine.com. Product Disposal Waste Electrical and Electronic Equipment (WEEE) Directive The WEEE Directive requires the recycling of waste electrical and electronic equipment. While the WEEE Directive does not apply to some of Raymarine's products, we support its requirements as part of our environmental policy and we ask you to be aware of how you should dispose of this product. The wheelie bin symbol found on our products signifies that it should not be disposed of in general waste or landfill. Please contact your local dealer, national distributor or Raymarine Technical Services for information on product disposal. Warranty To register your Digital Sounder Module ownership, please take a few minutes to fill out the warranty registration card found at the end of this handbook. It is very important that you complete the owner information and return the card to the factory in order to receive full warranty benefits. 7 Chapter 1: DSM Installation 1.1 Introduction This chapter provides details for mounting the DSM300 and DSM30 and connecting to the display. For the system to display depth, water temperature and speed, you must install the transducer type(s) capable of transmitting the appropriate data. Planning the Installation Before you install your system, plan the installation, considering: · Location of the sounder module, as described in Section 1.3 · Cable Runs, as described in Section 1.5 · Correct transducer for your application EMC Installation Guidelines All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised. Although every effort has been taken to ensure that they will perform under all conditions, it is important to understand what factors could affect the operation of the product. The guidelines given here describe the conditions for optimum EMC performance, but it is recognized that it may not be possible to meet all of these conditions in all situations. To ensure the best possible conditions for EMC performance within the constraints imposed by any location, always ensure the maximum separation possible between different items of electrical equipment. For optimum EMC performance, it is recommended that wherever possible: · Raymarine equipment and cables connected to it are: · At least 5 ft (1.5 m) from any equipment transmitting or cables carrying radio signals, e.g., VHF radios, cables and antennas. In the case of SSB radios, the distance should be increased to 7 ft (2 m). · More than 7 ft (2 m) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating element. 8 DSM300 and DSM30 Installation Manual · The equipment is supplied from a separate battery from that used for engine start. Voltage drops below 10 V and starter motor transients can cause the equipment to reset. This will not damage the equipment, but may cause the loss of some information and may change the operating mode. · Raymarine specified cables are used. Cutting and rejoining these cables can compromise EMC performance and must be avoided unless doing so is detailed in the installation manual. · If a suppression ferrite is attached to a cable, this ferrite should not be removed. If the ferrite needs to be removed during installation it must be reassembled in the same position. Suppression Ferrites The following illustration shows typical cable suppression ferrites used with Raymarine equipment. Always use the ferrites supplied by Raymarine. D3548-3 Connections to Other Equipment If your Raymarine equipment is to be connected to other equipment using a cable not supplied by Raymarine, a suppression ferrite must always be attached to the cable that is closest to the Raymarine unit. Chapter 1: DSM Installation 9 1.2 Unpacking and Inspecting the Components Unpack your system carefully, to prevent damage to the equipment. Save the carton and packing, in case you need to return the unit for service. Check that you have all the correct system components: DSM300 Power Cable, 3m part no. R69053 DSM300 Digital Sounder Module, part no. E63069 C Series Network Cable, 3m part no. E65010 DSM300 & DSM30 Installation Manual DSM300 Operation Manual hsb2 adapter, 4-pin to 3-pin part no. R69081 DSM30 Power Cable, 3m part no. R69053 Mounting Screws, No.8 (x4) DSM30 Digital Sounder Module, part no. E63074 DSM300 & DSM30 Installa ...