User manual RAYMARINE E-SERIES FULL FUNCTION REMOTE KEYBOARD

SeaTalk2 Keyboard Owner's Handbook Introduction www.raymarine.com PAGE ACTIVE WPTS MOB DATA MENU OUT OK CANCEL . IN This handbook explains how to install, connect, operate and maintain your SeaTalk2 Keyboard (E55061). This keyboard is also supplied with the Remote Station Kit (T82005) details of how to integrate these devices is given on Page 6. Intended use This keyboard is intended for use with Raymarine's E-Series display aboard leisure marine boats and workboats not covered by IMO/SOLAS carriage requirements. It can be integrated into an existing SeaTalk2 system, if required. Contents Subject Introduction The controls What's in the box? Safety notices Planning the installation Integrating the Remote Station Kit Installation Accessories and spares Removing/refitting Maintenance Important information Technical support and contact details 1 Page 1 2 3 3 4 6 7 9 10 10 11 12 D7679-1 The controls WPTS MOB To manage waypoints and initiate MOB. PAGE To change page and configure page sets. Power To turn display off and access backlight functions and scanner controls. Trackpad To control on-screen cursor and scroll through menu items. Soft keys Press to select corresponding function identified by on-screen label. PAGE ACTIVE WPTS MOB 1 2 ABC 3 DEF DATA MENU 4 GHI 5 JKL 6 MNO 7 PQRS 8 TUV 9 WXYZ OUT OK CANCEL E RANG . 0 IN ACTIVE To select the active window. MENU To access set up menus and help information. Keypad For making alphanumeric entries in on-screen dialog boxes. Range To change the display scale. CANCEL To cancel selected on-screen option when editing data and to return to previous soft key set or menu. OK To select on-screen option, or return to the previous soft key set/menu. DATA To access the ruler, chart vectors, archive and transfer, data bar on/off functions etc. Rotary control To scroll through lists and edit alphanumeric values. 2 D7702_1 For further details of the control functions, please refer to your E-Series Display Reference Manual. Whats in the box?. . . . Suncover Stud (x2) Clamp (x2) Thumb nut (x2) SeaTalk2 Keyboard Drain tube (8mm x 1m) SeaTalk2 cable (1.5m) Cradle SeaTalk2 power/RF ground cable (1.5m) Terminator (x2) Gasket SeaTalk2 Keyboard Owner's Handbook Introduction to the SeaTalk2 Keyboard www.raymarine.com PAGE ACTIVE WPTS MOB DATA MENU OUT OK CANCEL . IN This handbook explains how to install, connect, operate and maintain your SeaTalk2 Keyboard (E55061). This keyboard is also supplied with the Remote Station Kit (T82005) details of how to integrate these devices is given on Page 6. Intended use This product is a keyboard intended for use within a SeaTalk2 system and connected via a junction box to Raymarine's E-Series display. The intended application is for leisure marine boats and workboats not covered by IMO/SOLAS carriage requirements. The SeaTalk2 keyboard is waterproof to CFR-46 standard. Contents Subject Introduction The controls What's in the box? Safety notices Planning the installation Integrating the Remote Station Kit Installation Spares and accessories Removing/refitting Maintenance Important information Technical support and contact details 1 Page 1 2 3 3 4 6 7 9 10 10 11 12 Template 5-way junction box Handbook Safety notices WARNING: Navigation aid Although this product has been designed to be accurate and reliable, many factors can affect its performance. As a result, it should only be used as an aid to navigation and should never replace common sense and navigational judgement. Always maintain a permanent watch so you can respond to situations as they develop. WARNING: Product installation This equipment must be installed and operated in accordance with the instructions contained in this handbook. Failure to do so could result in poor product performance, personal injury and/or damage to your boat. WARNING: Electrical safety Make sure the power supply is switched off before you make any electrical connections. D7701-1 WARNING: Cable Do not disconnect the keyboard cable from the keyboard. 3 D7679-1 Planning the installation Where can the SeaTalk2 Keyboard be mounted? The Seatalk2 keyboard can be flush or trunnion mounted either indoors or outdoors. It is waterproof to CFR-46 standard. Important: The drain tube is not required if the keyboard is mounted indoors or in an area protected from rain and/or sea spray. If mounting the keyboard outdoors or in an unprotected area the drain tube will need to run to a suitable exit point below the level of the keyboard. What configuration should I use? How you connect the keyboard depends on the distances between your E-Series Display, the keyboard and power source and whether or not you are connecting the keyboard to an existing SeaTalk2 system. Select the appropriate configuration from the following: Configuration 1 Cable length between E-Series Display and keyboard less than 4.5m and Not linking into an existing SeaTalk2 system. Supplied in the box Not supplied/accessory/ existing system E Series display E-Series Display SeaTalk2 Keyboard Keyboard cable (attached/3 m) SeaTalk2 cable (1.5 m) SeaTalk2 Power/RF ground cable (1.5 m) 5A circuit breaker Or: Switch with 5A fuse red black grey Terminator Junction box Terminator 12v supply D7680-1 4 Configuration 2 Cable length between E-Series Display and keyboard exceeds 4.5m and Not linking into an existing SeaTalk2 system. Supplied in the box SeaTalk2 Keyboard Not supplied/accessory/ existing system E Series display E-Series Display Keyboard cable (attached/3m) SeaTalk2 extension cable (see 'Accessories') SeaTalk2 cable (1.5m) SeaTalk2 Power/RF ground cable (1.5m) 5A circuit breaker Or: Switch with 5A fuse red Junction box 12v supply black Terminator Terminator Additional junction box grey Configuration 3 Integrating the keyboard into an existing SeaTalk2 system. Supplied in the box Not supplied/accessory/ existing system E Series display SeaTalk2 Keyboard E-Series Display Keyboard cable (attached/3m) SeaTalk2 cable (1.5m) SeaTalk2 extension cable (see 'Accessories') SeaTalk2 extension cable (see 'Accessories') To: Existing SeaTalk2 system (incorporating terminators, power/RF ground) Junction box To: Existing SeaTalk2 system (incorporating terminators, power/RF ground) D7697-1 5 Integrating the Remote Station Kit Station 1 Other SeaTalk devices connected Alarm No other SeaTalk devices connected Alarm M1500 monitor Brown Black SeaTalk2 Keyboard OR Other SeaTalk devices Drain Yellow OR Refer to 'Planning the Installation', diagrams on pages 4 and 5. Junction box Remote Station Kit SeaTalk/Alarm out cable,1.5m Station 2 E Series SeaTalk2 cable (1.5 m) Keyboard cable (attached/3 m) Not supplied/accessory/existing system D7703-1 6 VGA out cable, waterproof (see Accessories) Drain White Black Red 12v supply Red VGA out cable, 5m NOT waterproof Brown Yellow Black Red White Black Red Installation Note: Before installing the keyboard, please read 'Planning the installation' on Pages 4 & 5. What tools do I need to install the keyboard? Drill 10 mm (3/8 in) drill bit File Jigsaw Masking or adhesive tape How do I install the keyboard? 1. Using self-adhesive or masking tape, fix the template in the required position. Note: Ensure that there are no cables or other parts that will be damaged, when the panel is drilled and sawn. 3. Saw around the shaded area of the template. 2. Drill a pilot hole inside the shaded area of the template. 4. Remove the tape and the template remains. Smooth the sawn edges with a file. 7 D7699-1 Installation - continued 5. Peel the backing from the gasket and stick it to the underside of the cradle. 8. Fit the keyboard assembly into its housing. With the dimples in the clamps fitting into the nipples on the cradle, fit and secure the clamps in place using the thumb nuts. 6. Finger tighten the studs into position. 9. Ensuring that the power is connected last, connect all the cables, terminators etc in the appropriate configuration (see 'Planning the Installation' on pages 4 to 6). Wrap any excess cable and tuck away. Do not cut and resplice cables. 7. If mounting the keyboard in an area unprotected from rain and/or sea spray, fit the drain tube and ensure that it runs to a suitable exit point below the level of the keyboard and the studs. 8 D7700-1 Accessories and spares What accessories are available? ... Description SeaTalk2 power/RF ground cable (1.5m) Auxiliary alarm M1500 monitor kit (includes 5m VGA Out cable) Terminator Junction box SeaTalk2 extension cables: E25040 E25042 E25043 E25038 E25044 cable (1.5m) E55053 E55055 E55056 E05012 1 metre 3 metres 5 metres 10 metres 20 metres E-Series SeaTalk2 VGA Out cables (waterproof): 10 metres 20 metres Trunnion mount kit Part no. E55070 E26033 E02009 E25048 E25049 What spares are available? ... Description Cradle assembly (includes cradle, cable, drain tube, gasket and latch) Flush mount kit (includes gasket, clamps, drain tube, studs and thumb nuts) Latch Suncover Part no. R58213 R58211 R89043 R58212 9 D7698-1 Removing/refitting How do I remove the keyboard? ... 3. Push down at the top of the keyboard to 1. Switch off the power. 2. Slide and hold the latch. raise it from the cradle and lift the it from the cradle. How do I refit the keyboard? ... 1. Position the top edge of the keyboard under the lip of the cradle. 2. Push the bottom of the keyboard into the cradle to engage the latch. Maintenance What routine checks and servicing can I do? ... On a regular basis, examine all cables for signs of damage, such as chafing, cuts or nicks and check that all cables are securely connected. The SeaTalk2 keyboard has no user serviceable parts. How should I clean my keyboard? ... Regularly clean your keyboard as follows: 1. Switch off the power. 2. Wipe the keyboard with a clean, soft cloth. To remove oily finger marks, use a spray cleaning agent of the type used for cleaning eyeglasses or a mild detergent. Do not use acid, ammonia based or abrasive products. 10 D7706-1 Important information EMC conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. The design and manufacture of Raymarine equipment and accessories conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised. For full details and installation guidelines refer to our web site at www.raymarine.com Warranty To register your new Raymarine product, please take a few minutes to fill out the warranty card. It is important that you complete the owner information and return the card to us to receive full warranty benefits. Your product can also be registered via our web site - www.raymarine.com Handbook information To the best of our knowledge, the information contained in this handbook was correct as it went to press. Raymarine cannot accept any liability for any inaccuracies or omissions it may contain. In addition, our policy of continuous product improvement may change specifications without notice. As a result, Raymarine cannot accept liability for any differences between the product and the handbook. Waste Electrical and Electronic Equipment Directive The Waste Electrical and Electronic Equipment (WEEE) Directive requires the recycling of waste electrical and electronic equipment. Whilst the WEEE Directive does not apply to some of Raymarine's products we support its policy and ask you to be aware of how to dispose of this product. The crossed out wheelie bin, illustrated above, and found on our product signifies that this product should not be disposed of in general waste or landfill. Please contact your local dealer, national distributor or Raymarine Technical Services for information on product disposal. 11 D7707-1 Technical support & contact information www.raymarine.com Visit the Customer Support area of our website for Frequently Asked Questions, servicing information, e-mail access to the Raymarine Technical Support Department and details of Raymarine agents, worldwide. United States For accessories and parts contact: Your authorized Raymarine dealer. or Raymarine Technical Services on: 1-800-539-5539 extension 2333, or (603)-881-5200. Opening hours: Monday through Friday 0815 - 1700, Eastern Standard or Eastern Daylight Savings Time. Europe For technical support, service and accessories contact: Your authorized Raymarine dealer. or Technical Support Raymarine UK Limited Anchorage Park Portsmouth PO3 5TD England Tel: +44(0)23 9271 4713 Fax: +44(0)2392661228 To verify your requirements contact: 1-800-539-5539 extension 2444, or (603)-881-5200. For product repair & service contact: Your authorized Raymarine dealer. or Return the unit to: Raymarine Product Repair Center 21 Manchester Street Merrimack, NH03054 - 4801 1-800-539-5539 Help us to help you D7708-1 When requesting service, please quote the following product information: Equipment type Model number Serial number Raymarine UK Limited Quay Point, Northarbour Road, Portsmouth, Hampshire England PO6 3TD Tel: + 44 (0)23 9269 3611 Fax: + 44 (0)23 9269 4642 www.raymarine.com Raymarine Incorporated 21 Manchester Street Merrimack, NH03054 - 4801 USA Tel: 603-881-5200 Fax: 603-864-4756 www.raymarine.com Document No: 81253_2 Date: June 2006 Raymarine 2006 12 SeaTalk2 Keyboard Interim sheet 82201-1 Configuration 4 Cable length between E-Series Display and keyboard less than 4.5m and Linking into an existing combined SeaTalk/SeaTalk2 system with ST290 DPU. Do not connect the ST290 to the E-Series SeaTalk2 connection. E Series display Note: For multiple keyboard installations, please refer to your local dealer or to www.raymarine.com SeaTalk2 Keyboard Note: For multiple keyboard installations, please refer to your local dealer or to www.raymarine.com SeaTalk2 Keyboard Interim sheet 82201-1 Configuration 4 Cable length between E-Series Display and keyboard less than 4.5m and Linking into an existing combined SeaTalk/SeaTalk2 system with ST290 DPU. Do not connect the ST290 to the E-Series SeaTalk2 connection. E Series display SeaTalk2 Keyboard SeaTalk2 cable SeaTalk2 Power/RF ground cable SeaTalk2 cable SeaTalk2 Power/RF ground cable Terminator grey Terminator Terminator Terminator grey SeaTalk cable Junction box SeaTalk cable red black 5A circuit breaker or 12v supply Switch with 5A fuse Junction box red black 5A circuit breaker or 12v supply Switch with 5A fuse Existing SeaTalk system To: Existing SeaTalk2 system (incorporating terminators, power/RF ground) Existing SeaTalk 2 system Existing SeaTalk system Existing SeaTalk 2 system To: Existing SeaTalk2 system (incorporating terminators, power/RF ground) SeaTalk cable SeaTalk cable SeaTalk2 cable SeaTalk cable SeaTalk cable SeaTalk2 cable To: Existing SeaTalk system (for example: GPS and Autopilot) ST290 DPU To: Existing SeaTalk system (for example: GPS and Autopilot) ST290 DPU Supplied in the box Supplied in the box Not supplied/accessory/ existing system D8056-1 D8056-1 Not supplied/accessory/ existing system