User manual RCA DRD435RH

Satellite Receiver User's Guide Changing Entertainment. Again. Important Information Cautions Do not stack electronic components or other objects on top of the Digital Satellite Receiver. The slots on top of the receiver must be left uncovered to allow proper airflow to the unit. Blocking the airflow to the unit could impair performance or damage your receiver and other components. Remove any sales or promotional materials attached to the product. Do not stack the digital satellite receiver on top of a "hot component" such as an audio power amplifier. FCC Regulations state that unauthorized changes or modifications to this equipment may void the user's authority to operate it. WARNING To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The apparatus shall not be exposed to dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the apparatus. CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Note to Cable TV Installer: This reminder is provided to call your attention to article 820-40 of the National Electrical Code (Section 54 of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. This symbol indicates "dangerous voltage" inside the product that presents a risk of electric shock or personal injury. This symbol indicates important instructions accompanying the product. Note to Satellite Dish Installer: This reminder is provided to call your attention to articles 810 and 820 of the 1999 National Electrical Code. Refer to article 810, in particular to 810-1 and 810-15, for required grounding of the metal structure of the Dish Antenna. Refer also to the 810-2 which, by reference to article 820, requires that the satellite dish coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as practical. IMPORTANT NOTICE: This device incorporates an anticopy process technology that is protected by U.S. patents and other intellectual property rights. The anticopy process is licensed for non-commercial, home use only. Reverse engineering or disassembly is prohibited. Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Care and Cleaning: Use a soft cloth or dusting attachment of your vacuum cleaner to dust your digital satellite receiver. Remove dust from the ventilation holes on the top and bottom. Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. A non-abrasive, anti-static cleaner/polisher is recommended. Product Registration Please fill out the product registration card (packed separately) and return it immediately, or register online at rca.com. Returning the card allows us to contact you if needed. Product Information Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial and model numbers in case you need them. These numbers are located on the product. Model No. ______________________________________________ Serial No. _______________________________________________ Purchase Date: __________________________________________ Dealer/Address/Phone: ____________________________________ Table of Contents Chapter 1: Connections & Setup Things To Consider Before You Connect Components ................ 2 Choose Your Connection................................................................ 2 Insert Your Access Card ................................................................. 2 Excellent Connection ..................................................................... 3 Very Good Connection ................................................................... 4 Basic Connection ............................................................................ 5 Advanced Audio (Optical Digital Audio Output Connection) .... 6 Jacks and Cables............................................................................. 6 Satellite Receiver Rear Panel ........................................................ 7 Place Batteries in the Remote Control ........................................ 8 Plug in and Turn on the Receiver ................................................. 8 Wait for the Receiver to Download ADVANCED PROGRAM GUIDETM Data ....................................... 8 Using Highlight and Select ............................................................ 9 Complete the Assisted Setup ........................................................ 9 Order Programming ........................................................................ 9 Chapter 4: Using On-Screen Menus Using the Menu System............................................................... 23 Main Menu Items ......................................................................... 24 The Program Guide ....................................................................... 24 Messages ....................................................................................... 25 Mail .......................................................................................................... 25 Caller ID .................................................................................................. 25 Using the Purchases Menu .......................................................... 27 Reviewing and Canceling Upcoming Purchases ......................... 27 Spending Limits .................................................................................... 27 Pay Per View Programs ....................................................................... 27 Timers ............................................................................................ 28 User Profiles .................................................................................. 29 Creating and Editing User Profiles .................................................. 29 Creating a Profile Channel List ........................................................ 29 Setting the Rating Limit .................................................................... 30 Viewing Hours ...................................................................................... 30 Setting Up Spending Limits .............................................................. 30 Locking a User's Profile ...................................................................... 31 Locking the System ............................................................................. 31 Unlocking the System ......................................................................... 32 Choosing Your Profile ......................................................................... 32 Personal Settings .......................................................................... 32 Name ....................................................................................................... 32 Guide Settings ................................................................................. 33 Channel Banner .................................................................................... 33 Color Scheme ................................................................................... 33 Translucency ..................................................................................... 33 Animation ......................................................................................... 33 Edit Fetch .......................................................................................... 33 INFO Message .................................................................................. 34 System Setup ................................................................................ 34 Assisted Setup .................................................................................. 34 Receiver Index ...................................................................................... 34 Receiver Options .................................................................................. 34 Dish Pointing ......................................................................................... 36 System Test ............................................................................................ 37 System Info ............................................................................................ 37 System Upgrades ................................................................................. 37 New Access Card ................................................................................. 37 Alternate Data ...................................................................................... 37 Interactive ..................................................................................... 37 Chapter 2: Using the Remote Control Remote Control Buttons .............................................................. 10 Top of the Digital Satellite Receiver .......................................... 11 Programming the Remote Control ..............................................11 Testing the Remote Control .............................................................. 11 Using Automatic Code Search ......................................................... 11 Using Direct Entry ............................................................................... 12 Operating Other Components ..................................................... 12 Modes of Operation ............................................................................ 12 Controlling a Second RCA Satellite Receiver ............................... 12 Chapter 3: Satellite Receiver Features The Program Guide ....................................................................... 15 Displaying the Toolbar ........................................................................ 15 The Channel Banner ..................................................................... 16 The DIRECTV INTERACTIVETM Feature ......................................... 17 Displaying On-screen Guides ...................................................... 17 The Detail Guide ................................................................................... 17 The Grid Guide ...................................................................................... 17 Getting Around In the Guides ..................................................... 18 More Details .......................................................................................... 19 Additional Program Guides ......................................................... 19 The Channel Guide .............................................................................. 19 The Logo Guide ..................................................................................... 19 The Suggestion Guide ......................................................................... 20 The Category Guide ............................................................................. 20 The AlphaSortTM Guide ........................................................................ 21 The ScoutTM Guide ................................................................................ 21 The Profile Guide .................................................................................. 21 The Guide Toolbar ........................................................................ 22 Chapter 5: Other Information Troubleshooting ............................................................................ 38 Running the System Test ................................................................... 40 Fine-Tuning the Signal ....................................................................... 40 Finding the TV's Video Line Input .................................................... 40 Limited Warranty ......................................................................... 41 Accessory Information ................................................................. 44 Index .............................................................................................. 45 1 Chapter 1: Connections & Setup Things To Consider Before You Connect Components Protect Your Components from Power Surges · Connect all components before plugging any power cords into the wall outlet. · Always turn off the digital satellite receiver, TV and other components before you connect or disconnect any cables. Position Cables Correctly to Avoid Audio Hum or Interference · Insert all cable plugs firmly into their jacks. · Place the Audio/Video (A/V) cables to the sides of the TV's back panel instead of straight down the middle after you connect your components. · Try not to coil any twin-lead cables and keep them away from the A/V cables as much as possible. · Make sure all antennas and cables are properly grounded. See the inside front cover of this book for more information. Protect Your Components from Overheating · Do not block ventilation holes in any of the components. Arrange the components so that air can circulate freely. Remove any sales or promotional materials attached to the product. · Do not stack components. · Allow adequate ventilation when placing components in a stand. · Place an amplifier or receiver on the top shelf of the stand so heated air rising from it will not flow around other components. Choose Your Connection There are several ways to connect your digital satellite receiver depending on the components you want to connect and the quality of the signal you want to achieve. The next four pages show three options for connecting your satellite receiver to your other components, plus instructions for connecting your satellite receiver to a digital audio receiver. Choose the connection that most closely matches your components in order to get the best signal you can. For example, if your TV has an S-Video input, use the Excellent Connection shown on the next page as a guide. If your TV only has an RF coaxial input, use the Basic Connection shown on page 5 as a guide. Page 6 shows the kinds of cables you'll use to make connections. Insert Your Access Card Find the access card in the material that came with your receiver. Make sure the card is facing up, and fully insert it into the slot on the right side of your satellite receiver. 2 Illustrations contained in this document are for representation only. Chapter 1 Connections & Setup Excellent Connection RJ11 modular phone jack Satellite Dish Antenna Digital Satellite Receiver Using S-Video and A/V jacks and cables to connect to the TV, RF coaxial cables to connect the VCR This connection provides the best picture quality, surpassing that of A/V cables. The S-Video cable, which carries video information only, requires that audio cables also be used for sound. What you will need (see page 6 for descriptions of these cables): SATELLITE IN 5 GROUND PHONE ­R­ OUT TO TV ­L­ AUDIO IN FROM ANT VIDEO S-VIDEO 1 DIGITAL LOW SPEED DATA AUDIO · · · · Two (2) RF coaxial cables Two (2) A/V cables One (1) S-Video cable One (1) telephone line cord Coaxial cable lines fed from a digital satellite antenna and a standard TV antenna (or cable line) 2 VCR 4 IN Cable or Off-air Antenna · 6 7 TV R CH3 CH4 Making the Connection 1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the SATELLITE IN jack on the satellite receiver. 2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the satellite receiver, and the other end to the antenna input jack on the VCR. 3 L AUDIO FROM ANT VIDEO S-Video Note: If your VCR has A/V input jacks, you can use A/V cables to connect the satellite receiver's second A/V jacks to the A/V jacks of the VCR instead of using the RF coaxial cable. 3. Connect one end of an RF coaxial cable to the antenna output jack on the VCR, and the other end to the TV's antenna input jack. 4. Connect the cable or off-air antenna feed (RF coaxial cable) to the IN FROM ANT jack on the satellite receiver. 5. Connect one end of the supplied telephone line cord to the PHONE JACK on the back of the satellite receiver, and the other end to an RJ11-type modular phone jack (the most common type of phone jack). 6. Connect two ends of the supplied A/V cables to AUDIO R and L jacks on the satellite receiver, and the other ends to the corresponding audio input jacks on the TV. Note: Make sure you connect jacks by their labels. For example, AUDIO R on the digital satellite receiver should be connected to TV's right audio input jack, L Audio to L Audio, etc. If your TV only has one audio input jack, use the satellite receiver's AUDIO L jack to make the connection. Note: Your VCR and TV back panels may not look exactly like the ones illustrated. 7. Connect one end of the supplied S-Video cable to the satellite receiver, and the other end to the S-Video input jack on the TV. Go to Page 6 Using Your Components To watch DIRECTV® programming: Tune the TV to its S-Video line input (if you have difficulty finding your TV's S-Video line input, see your TV's User's Manual or page 40 in this manual). Then tune the satellite receiver to the desired channel. To record DIRECTV programming: Tune the satellite receiver to the desired channel. Then set your VCR to record on the proper input channel (video line input if using A/V cables to connect the VCR to the satellite receiver, channel 3 or 4 if using RF coaxial cable). To view VCR recordings: Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual. DIRECTV programming is subject to the terms and conditions of the DIRECTV Customer Agreement; a copy is provided at DIRECTV.com and with your first bill. See page 9 for more information. Chapter 1 3 Connections & Setup Very Good Connection RJ11 modular phone jack Satellite Dish Antenna Digital Satellite Receiver Using A/V jacks and cables to connect to the TV, RF coaxial cables to connect the VCR This connection provides better picture quality than RF coaxial cables and is recommended for use with TVs that do not have S-Video input jacks. What you will need (see page 6 for descriptions of these cables): · Two (2) RF coaxial cables Three (3) Audio/Video cables One (1) telephone line cord Coaxial cable lines fed from a digital satellite antenna and a standard TV antenna (or cable line) 5 GROUND PHONE ­R­ OUT TO TV ­L­ AUDIO IN FROM ANT VIDEO S-VIDEO 1 SATELLITE IN · · · DIGITAL LOW SPEED AUDIO DATA 4 2 VCR CH3 CH4 IN Cable or Off-air Antenna Making the Connection 1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the SATELLITE IN jack on the satellite receiver. 2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the satellite receiver, and the other end to the antenna input jack on the VCR. Note: If your VCR has A/V input jacks, you can use A/V cables to connect the satellite receiver's second set of A/V output jacks to the A/V jacks of the VCR instead of using the RF coaxial cable. 6 3 TV 3. Connect one end of an RF coaxial cable to the antenna output jack on the VCR, and the other end to the TV's antenna input jack. 4. Connect the cable or off-air antenna feed (RF coaxial cable) to the IN FROM ANT jack on the satellite receiver. R IN FROM ANT AUDIO L 5. Connect one end of the supplied telephone line cord to the PHONE JACK on the back of the satellite receiver, and the other end to an RJ11-type modular phone jack (the most common type of phone jack). 6. Connect the ends of the supplied A/V cables to the satellite receiver's AUDIO and VIDEO jacks, and the other ends to the corresponding AUDIO and VIDEO input jacks on the TV. Notes: Make sure you connect jacks and cables corresponding to their labels. For example, AUDIO R output on the digital satellite receiver should be connected to AUDIO R input on the TV, VIDEO out to VIDEO in, etc. If your TV only has one audio input jack, use the satellite receiver's AUDIO L jack to make the connection. Note: Your VCR and TV back panels may not look exactly like the ones shown. Go to Page 6 Using Your Components To watch DIRECTV® programming: Tune the TV to its video line input (if you have difficulty finding your TV's video line input, see your TV's User's Manual or refer to the instructions on page 40 in this manual). Then tune the satellite receiver to the desired channel. To record DIRECTV programming: Follow the steps in the previous step, then tune the satellite receiver to the desired channel. Set your VCR to record on its proper input channel (channel 3 or 4). To view VCR recordings: Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual. 4 Chapter 1 Connections & Setup Basic Connection RJ11 modular phone jack Satellite Dish Antenna Using RF Coaxial cables for all connections This connection provides standard picture quality. This connection is only recommended for use with TVs that do not have S-Video or A/V input jacks. Digital Satellite Receiver 5 GROUND PHONE ­R­ OUT TO TV ­L­ AUDIO IN FROM ANT VIDEO S-VIDEO 1 SATELLITE IN What you will need (see page 6 for descriptions of these cables): · · · Two (2) RF coaxial cables One (1) telephone line cord Coaxial cable lines fed from a digital satellite antenna and a standard TV antenna (or cable line) DIGITAL LOW SPEED AUDIO DATA 4 2 VCR CH3 CH4 IN Making the Connection Cable or Off-air Antenna 1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the SATELLITE IN jack on the satellite receiver. 2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the satellite receiver, and the other end to the antenna input jack on the VCR. 3. Connect one end of an RF coaxial cable to the antenna output jack on the VCR, and the other end to the TV's antenna input jack. 4. Connect the cable box or off-air antenna feed (RF coaxial cable) to the IN FROM ANT jack on the satellite receiver. 3 TV 5. Connect one end of the supplied telephone line cord to the PHONE JACK on the back of the satellite receiver, and the other end to an RJ11-type modular phone jack (the most common type of phone jack). Go to Page 6 IN FROM ANT Note: Your VCR and TV back panels may not look exactly like the ones shown. Using Your Components To watch DIRECTV® programming: Tune the TV to the satellite receiver's output channel (either channel 3 or 4). Note: You can change the satellite receiver's output channel by pressing the remote control's DIRECTV button, then the MENU button, then select System Setup, then Receiver Options, and finally select Output Channel. Use the remote control's arrow and SELECT buttons to highlight and select the desired output channel. Tune the TV to that channel to see the satellite receiver's picture. To record DIRECTV programming: Follow the directions in the previous step, then set your VCR to record on its proper input channel (channel 3 or 4 if using RF coaxial cable to make the connection, Video Line Input if using A/V cables to connect the VCR to the satellite receiver). To view VCR recordings: Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual. Chapter 1 5 Connections & Setup Receiver or Decoder with Optical Input Advanced Audio (Optical Digital Audio Output Connection) DIGITAL AUDIO INPUT Cables: Optical Digital Audio Your digital satellite receiver has a PCM digital audio output jack. This can be connected to an external Digital Audio Receiver/Decoder equipped with a compatible digital audio input. SATELLITE IN Digital Satellite Receiver GROUND PHONE ­R­ OUT TO TV VIDEO S-VIDEO ­L­ AUDIO IN FROM ANT Note: Your digital audio receiver's back panel may not look exactly like the one pictured. This satellite receiver's digital output jack outputs digital audio signals in PCM format. It is designed for connection to an external digital audio receiver/ decoder. DIGITAL LOW SPEED DATA AUDIO Making the Connection Connect one end of the optical cable to the DIGITAL AUDIO output jack on the satellite receiver, and to the digital audio input jack on your digital audio receiver/decoder. Jacks and Cables Below is a description of the jacks and cables you can use to make connections. Not all cables come with your digital satellite receiver. S-Video Jack and Cable S-VIDEO S-Video jacks/cables provide this receiver's best picture quality. Remember to connect the left and right audio cables to the TV because the S-Video cable carries only the picture signal, not the sound. Audio/Video (A/V) Jack and Cable (RCA-type) Audio/Video (A/V) cables provide good picture quality and stereo sound, and should be used if your TV has no Svideo jacks. The digital satellite receiver's A/V jacks are color coded (yellow for video, red for right audio, and white for left audio). If your TV has only one input for audio (mono), connect it to the left (white) audio jack on the satellite receiver. L VIDEO AUDIO R RF Jack and Coaxial Cable (F-type) RF jacks provide good picture and mono sound quality. They should be used if A/V connections are not available on your TV. RF jacks are used for off-air antenna and cable feed connections. The RF jacks on the receiver are labeled IN FROM ANT and OUT TO TV. The coaxial cable supplied with your system is used to connect the receiver to your TV/VCR's antenna input jack. ANTENNA IN Digital Audio Output DIGITAL AUDIO If you own an A/V receiver that includes a PCM-compatible decoder, use a digital audio cable (not included) to connect the satellite receiver to your external A/V receiver/decoder. Telephone Jack and Cord The telephone line cord is required to connect your satellite receiver to a telephone line if you choose to subscribe to DIRECTV® programming. The phone line connection is used to periodically call out to DIRECTV. You will need an RJ11-type modulator jack (the most common type of phone jack) which might look like one of those pictured here. If you don't have a modular jack, call your local telephone company to find out how to get one installed. PHONE 6 Chapter 1 Connections & Setup GROUND PHONE ­R­ OUT TO TV VIDEO S-VIDEO ­L­ AUDIO IN FROM ANT SATELLITE IN Satellite Receiver Rear Panel This diagram illustrates each of the back panel jacks found on your digital satellite receiver. When working with cables, be sure to connect corresponding outputs and inputs (Video out to Video in, Right Audio out to Right Audio in, etc.). For more information on the function of the back panel jacks and many other features of your digital satellite receiver, press the MENU button and select System Setup from the Main menu, then select Receiver Index. DIGITAL AUDIO LOW SPEED DATA Back Panel Jacks (in alphabetical order) AUDIO (R and L) Audio cables offer better sound quality than RF coaxial cables. Connect a second set of audio cables to another component, such as a VCR or stereo. DIGITAL AUDIO Connects the satellite receiver's audio to a PCM-capable receiver or decoder. This audio connection typically provides the best sound quality. Use an optical digital audio cable to make this connection. IN FROM ANT Connect a standard TV antenna or cable feed to the satellite receiver using this jack. You can then switch between the satellite receiver's signal and the TV/cable feed using the remote control's ANTENNA button to toggle between the two. LOW SPEED DATA This port allows you to connect your digital satellite receiver to future services and accessories as they become available. A shielded cable and additional hardware may be required. OUT TO TV Connects the satellite receiver to your TV or VCR using RF coaxial cable. This jack provides the most basic connection, carrying average sound and video quality. PHONE Connects the satellite receiver to a telephone line. The digital satellite receiver requires a telephone line connection to periodically communicate with your program provider. SATELLITE IN Use to connect the satellite receiver to the satellite dish antenna. S-VIDEO Provides better picture quality than VIDEO or RF coaxial cable jacks. If your TV has an S-Video jack, use it along with the audio jacks (SVideo only carries picture information, not sound) to connect to your TV. VIDEO Provides better picture quality than the OUT TO TV jack. Connect the second VIDEO jack to another device, such as a VCR. You must also connect the AUDIO cables when using the VIDEO connection. Chapter 1 7 Connections & Setup Place Batteries in the Remote Control Follow these steps whenever you need to install or change the batteries in your digital satellite receiver's remote control. Note: When replacing old batteries, you may need to reprogram the remote control to operate other devices. Avoid pressing any of the remote control buttons while you're replacing old batteries. If you press a remote control button while replacing batteries, you will need to reprogram the remote control to operate other devices. 1. Remove the cover from the battery compartment. 2. Insert batteries in the battery compartment, matching the + and ­ end of each battery. 3. Replace the cover. Note: The message "Searching for Satellite Signal" might appear briefly at the bottom of your screen when you turn on your satellite receiver for the first time. This is normal. If this message stays on the screen for more than one minute, check your receiver's on-screen signal meter to make sure your antenna is receiving the strongest possible satellite signal. See "Signal Meter" on page 36 for more information. Plug in and Turn on the Receiver Plug the end of the power cord into the wall outlet. Be sure to insert the plug completely. To turn on the satellite receiver, press the DIRECTV button on the remote control or the POWER button on the front panel. If your TV brand is RCA, GE, or Proscan, press the TV button on the remote control to turn on the TV. If your TV brand is not RCA, GE, or Proscan, see page 11 in the next section, Using the Remote Control, for details on programming the satellite receiver's remote control to operate your TV. Wait for the Receiver to Download ADVANCED PROGRAM GUIDETM Data The first time you connect a receiver to a satellite antenna you've already installed and pointed correctly, the receiver starts to gather information for the program guide. After you turn on your receiver and tune your TV to the correct video input channel, a progress bar appears indicating that the receiver is gathering this program guide information. To prevent any damage to your TV screen, the progress bar disappears after 2 minutes (the screen goes blank). Note: When the progress bar reaches 100%, there might be a delay before you actually see video on the screen. If the screen stays blank for more than 2 to 3 minutes, you need to reset the receiver. To reset the receiver: Note The Satellite Data Acquisition screen will also appear when: · your unit loses power (either from a power outage or being unplugged) · your unit loses the satellite signal for an extended period of time. 1. Unplug the satellite receiver's power cord from the power outlet. 2. Wait a few seconds, and plug the power cord back into the outlet. 3. Turn on the receiver and wait for it to download program guide information. 8 Chapter 1 Connections & Setup Using Highlight and Select VCR ON OFF TV All on-screen menus can be handled the same way, using highlight and select navigation. Highlight and select navigation has two steps: DIRECTV button DVD AUX1 AUX2 DIRECTV MUTE CH + SKIP 1. Use the arrow buttons (up, down, left, and right) on the remote control to highlight different choices on the screen. 2. Press SELECT to select the highlighted item. Note: When a highlighted on-screen menu choice has a number beside it, you can also press the corresponding number button on the remote control to select it. VOL VOL FETCH GUIDE CH - GO BACK INFO Once you know how to navigate on-screen menus, you can complete the Assisted Setup (see the next step) and explore the menu system. SELECT button Arrow buttons MENU button MENU SELECT (-) To display the on-screen menu system, press the remote control's DIRECTV button, then press the MENU button. Note: Don't worry about getting stuck inside a menu. Pressing the CLEAR button on the remote control takes you out of the menu system and back to the program you were watching. CLEAR CLEAR button Complete the Assisted Setup If you installed your satellite dish antenna yourself, you may have already used the Assisted Setup to find dish-pointing coordinates, acquire and finetune the signal, and run a system test. If you need to run the setup again, select System Setup from the Main menu, then select Assisted Setup. To check your dish-pointing coordinates or run the signal strength meter, display the Main menu, then select System Setup, and finally Dish Pointing. Tip When you order programming, you need to know your access card and receiver ID numbers. To get these numbers, select System Setup from the Main menu, then System Test. Wait for the system to run all of its tests. The access card and receiver ID numbers are displayed at the end of the system test. Write the access card and receiver ID numbers in the space below for easy reference: Order Programming After you have installed your DIRECTV® System, you should contact DIRECTV to order DIRECTV® programming. With this receiver and the proper satellite dish antenna, you may be able to subscribe to local channels from DIRECTV in certain areas. Additional equipment may be required in some markets. Check with your retailer or visit DIRECTV.com for information on availability of local channels from DIRECTV in your area. ACTIVATION OF PROGRAMMING MAY BE SUBJECT TO CREDIT APPROVAL AND REQUIRES VALID SERVICE ADDRESS, SOCIAL SECURITY NUMBER AND/OR MAJOR CREDIT CARD. DEPOSIT OR PREPAYMENT MAY BE REQUIRED. Professional and collegiate sports subscriptions sold separately. Eligibility for local channels based on service address within certain designated market areas as defined by Nielsen Media Research, Inc. In some areas served by members or affiliates of the National Rural Telecommunications Cooperative, local channels may be available from DIRECTV rather than the NRTC member or affiliate. Programming, pricing, terms and conditions subject to change. Hardware and programming sold separately. Pricing is residential. Taxes not included. Equipment specifications and programming options may vary in Alaska and Hawaii. DIRECTV services not provided outside the U.S. DIRECTV programming is sold separately and independently of DIRECTV System hardware. A valid programming subscription is required to operate DIRECTV System hardware. Receipt of DIRECTV programming is subject to the terms of the DIRECTV Customer Agreement; a copy is provided at DIRECTV.com and in your first bill. Activate your DIRECTV® programming today at 1-800-DIRECTV (1-800-347-3288). Important! If local channels are available in your area and you decide to subscribe, the receiver will need to download all of your program guide information again. This might take a few minutes. See "Wait for the Receiver to Download ADVANCED PROGRAM GUIDETM Information" on page 8 for more information. Chapter 1 9 Chapter 2: Using the Remote Control Remote Control Buttons ON·OFF Turns the component you are controlling on or off. When pressed twice within two seconds, all components that are on are turned off (this feature only works with most RCA, GE, and Proscan products). The component keys also light up, one after another, counterclockwise in a circle. VCR When programmed, tells the remote to control the VCR. This button lights up when you press a valid button in VCR mode (see Modes of Operation on page 12 for more details). AUX1 Turns on a second RCA satellite receiver. AUX1 can also be programmed to control an auxiliary component. This button lights up when you press a valid button in AUX1 mode (see Modes of Operation on page 12 for more details). DVD When programmed, tells the remote to operate the DVD player. This button lights up when you press a valid button in DVD mode (see Modes of Operation on page 12 for more details). When programmed to control a TV or audio receiver, this button reduces that component's volume to its minimum level. Press again to restore the volume. CH + and CH - Use to scan up and down through the channels in the current channel list. In the program guide or menu system, use the CH buttons to page up and down a screen at a time. FETCH In the program guides, displays the guide toolbar at the bottom of the screen. During normal viewing, displays the Fetch menu with up to eight different actions, or executes a single task- depending on the preferences set. MUTE TV When programmed, tells the remote to control the TV. This button lights up when you press a valid button in TV mode (see Modes of Operation on page 12 for more details). AUX2 Turns on a compatible RCA amplifier/ audio receiver. AUX2 can be programmed to control an auxiliary component. This button lights up when you press a valid button in AUX2 mode (see Modes of Operation on page 12 for more details). DIRECTV Tells the remote to control the digital satellite receiver. This button lights up when you press a valid button in DIRECTV mode (see Modes of Operation on page 12 for more details). SKIP Activates the commercial skip mode on some RCA, GE, and Proscan products that offer Commercial Skip feature. See the user's manual that came with your TV for more information. Activates the search function on some RCA, GE, or ProScan VCRs (when the remote is in VCR mode). VOL up and down When programmed, adjusts the audio volume of your TV or audio receiver. GO BACK Moves you back and forth between the last two selected channels. In the menu system, returns you to the previous screen. INFO Brings up the on-screen channel banner. In the program guides, INFO gets information about the highlighted program or channel. In the menu system, INFO displays context-sensitive help for highlighted control elements. Arrows Moves the on-screen highlight up, down, left, or right. VCR ON OFF TV DVD AUX1 AUX2 DIRECTV MUTE CH + SKIP VOL VOL FETCH GUIDE CH - GO BACK INFO (-) MENU CLEAR 1 2 5 8 0 3 6 9 ANTENNA GUIDE Brings up the program guide. Subsequent presses of the GUIDE button switch between the Detail and Grid guide formats. SELECT/i (interactive) Selects a highlighted choice if you are in the menu system. Also brings up the password challenge and purchase offer screens outside of the menu system. Press the SELECT button when the DIRECTV INTERACTIVETM icon ( ) appears during interactive programs and commercials. Pressing SELECT displays more information and offers the chance to interact with what is displayed on screen. 4 7 WHO INPUT STOP PAUSE CLEAR Removes the on-screen displays and returns you to normal viewing. Digit Buttons (0 - 9) Tune directly to a specific channel. In the menu system, use 1-9 to select menu items, or use 0 to return to the previous menu screen. MENU Displays the Main menu. When using the remote control to operate other components, the MENU button might also bring up that component's menu system. WHO·INPUT Press one or more times to scroll through the user profiles. When using the remote control to operate an RCA, GE, or PROSCAN TV (in TV mode), press the WHO·INPUT button one or more times to scroll through the available video input sources. Transport Buttons (REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE) In on-screen guides, PLAY advances the display one page, FORWARD advances the display 6 hours and REVERSE moves time backward 6 hours. When the remote control is programmed, these buttons also control an auxiliary component, such as a VCR or DVD player (when the remote is in the correct mode). ANTENNA In TV mode, toggles between the satellite and standard TV/cable signals when the satellite receiver is connected to the TV using the OUT TO TV jack. In VCR mode, functions as a TV/ VCR input button. Note: The component key corresponding to the mode you're in flashes when the remote batteries are low and you press a button on the remote. A warning banner may also appear on-screen when you press a remote button and your batteries are low (if you're watching satellite programming). 10 Chapter 2 Using the Remote Control Top of the Digital Satellite Receiver This diagram illustrates the buttons on the top (also referred to as the front panel) of the digital satellite receiver. For more information on the function of the front panel buttons and many other features of your digital satellite receiver, press the MENU button and select System Setup from the Main menu, then select Receiver Index. POWER M EN U / SEL CT E INFO Front Panel Buttons POWER Use to turn your digital satellite receiver on for viewing or off when you are not viewing it. Your receiver will still be able to download software upgrades and receive messages from program providers when it is off. MENU / SELECT Use this button to display the Main menu, password challenge screen or purchase offer screen. If you are already in the menu system, pressing this button selects the highlighted item. Arrows Use the navigation arrows to move the on-screen highlight up, down, left, or right. INFO Use this button to display the channel banner. Press twice to display additional program information, when available. While in the menu system INFO also summons context sensitive help about a highlighted menu item. Programming the Remote Control VCR ON OFF TV Component buttons and ON·OFF button DVD AUX1 AUX2 DIRECTV The digital satellite receiver's remote can be programmed to control most brands of remote controllable components. The remote is already programmed to control most RCA, GE and Proscan components; it may need to be programmed to control other manufacturers' brands. MUTE CH + SKIP Testing the Remote Control To determine whether the universal remote control needs to be programmed, turn a component on, such as a VCR, point the remote at the VCR, and press the VCR button. Then press the ON·OFF or CH + and CH - buttons to see if the VCR responds to the remote commands. If not, the remote needs to be programmed. There are two ways to program the remote control: Automatic Code Search or Direct Entry. VOL VOL FETCH GUIDE CH - GO BACK INFO (-) Using Automatic Code Search The following instructions can be used to program the remote to control many of the components connected to your TV. If you want to exit the automatic code search without programming any of your components, press the CLEAR button until the component button you're trying to program turns off. 1. Turn on the component you want to control (VCR, satellite receiver, etc.) 2. Press and hold the button you want to program. While holding the component button, press and hold ON·OFF until all of the component buttons (VCR, DVD, TV, DIRECTV, AUX1 and AUX2) flash. Then, release both buttons. Note: The AUX1 and AUX2 buttons will only search through the codes for their default type of component during the automatic code search ­ satellite receivers for AUX1 and audio components for AUX2. If you want to use these buttons for a different type of component ­ for example, a DVD player for AUX1 ­ then use direct entry to program these buttons. See the next page for more information. MENU CLEAR 1 4 2 5 8 0 3 6 9 ANTENNA PLAY button 7 WHO INPUT REVERSE button STOP PAUSE STOP button Note: The DIRECTV button cannot be programmed. 3. Point the remote at the component, press and release PLAY, then wait five seconds or until the component button you're trying to program stops flashing. At this point the remote control is searching for the correct code to program, so keep pointing it at the component. If, after five seconds, the component you want to control does not turn off, press and release PLAY again to tell the remote to search the next set of codes. Continue pressing and releasing PLAY until the component turns off or until the all of the component buttons on the remote flash 4 times in unison. If the component has not turned off by the time all the component buttons on the remote control flash 4 times in unison, then the remote cannot control that particular component. If the component you want to control does turn off: 1. Press and release REVERSE, then wait two seconds. Repeat this step until the component turns back on. 2. To finish, press and hold STOP until the component button you're trying to program on the remote control turns off. This saves the code to that button. Chapter 2 11 Using the Remote Control Important: This remote may not be compatible with all models of all brands of components. It also may not operate all functions of the remote that came with your component. Using Direct Entry 1. Turn on the component to be programmed. 2. Look up the brand and code number(s) for the component on the code list at the end of this section. 3. On your remote control, press and hold the component button you want to program. 4. While pressing the component button, enter a code from the code list. If all of the component buttons flash 4 times in unison, then the code you've entered is not the right kind of code for that button (see pages 13-14 to see which buttons can be programmed to control the component you want). 5. Release the component button, point the remote at the component and then press ON·OFF to see if the component responds to the remote control commands. If it doesn't, try pressing the component button and then ON·OFF (or other buttons on the remote) again. 6. If you get no response, repeat these steps using the next code listed for your brand, until the component responds to the remote control commands. Component buttons Note: The DIRECTV button cannot be programmed. Operating Other Components Once the remote has been programmed successfully, you are ready to use it to operate your components. To Operate the Component: 1. Press the component button (TV, VCR, DVD, DIRECTV, AUX1, or AUX2) to set the remote to control the component. 2. Press ON·OFF to turn the component on or off. 3. Use the remote control buttons that apply to that component. The component button on your remote lights up when you press valid buttons while in that component's mode. Note: Your remote's buttons might operate differently for other components, especially when you're using another component's menu system. VCR ON OFF TV DVD AUX1 AUX2 DIRECTV CH + Tip: If something unexpected happens (or if nothing happens) when you press a remote control button, check which component button lights up when you press that button. If the wrong component button lights up, press the component button the corresponds to the component you want to control ­ this puts the remote control in the right mode. Now that the remote is in the correct mode, press the button you were pressing before. Modes of Operation Because this universal remote can control several different components (DVD player, VCR, cable box, etc.) it uses operational modes triggered by the component buttons. For example, if you want the remote control to operate the TV, press the TV button to put the remote into TV mode. If you want the remote to operate the VCR, press the VCR button. The button corresponding to the mode the remote is in lights up when you press any button that works in that mode. For example, if you're in TV mode and you press the VOL+ button, the TV button lights up. This tells you that the command to increase the volume is being sent to the TV (and not the satellite receiver, for example). Controlling a Second RCA Satellite Receiver The remote can control two RCA satellite receivers. From the Main menu, select System Setup, then Receiver Options, then Remote Setup. Then follow the on-screen instructions. By default, the DIRECTV button is used to control the first RCA satellite receiver and the AUX1 button is used to control the second RCA satellite receiver. If your second receiver is an RCA, GE, or Proscan and you want to control it using the AUX1 button, use code 5001. Code 5000 is used by the DIRECTV button. If you want to control a second non-RCA satellite receiver, use the AUX1 or AUX2 buttons. See the Using Automatic Code Search section on the previous page for more information. 12 Chapter 2 Code List TV (programmable to the TV, AUX1 and AUX2 buttons) Abex ................................................................................... 1172 Admiral ......................................................... 1001, 1173, 1211 Adventura .......................................................................... 1174 Aiko .................................................................................... 1016 Akai ................................................................................... 1002 Alleron .............................................................................. 1046 Amtron .............................................................................. 1038 Anam National ....................... 1003, 1038, 1192, 1193, 1194 AOC ..................... 1004, 1005, 1006, 1007, 1175, 1176, 1195 Audiovox .......................................................................... 1038 Belcor ................................................................................ 1004 Bell & Howell ............................................... 1001, 1083, 1162 Bradford ............................................................................ 1038 Brokwood ......................................................................... 1004 Candle ................................................ 1004, 1006, 1008, 1174 Celebrity ........................................................................... 1002 Centurion .......................................................................... 1009 Citizen ...... 1004, 1006, 1008, 1016, 1038, 1105, 1171, 1174, 1177 Colortyme ..................................................... 1004, 1006, 1010 Concerto ................................................................. 1004, 1006 Contec/Cony ...................................... 1012, 1013, 1014, 1038 Craig .................................................................................. 1038 Crown ...................................................................... 1038, 1171 Curtis Mathes .............. 1000, 1004, 1006, 1015, 1105, 1162, 1171, 1212 CXC ................................................................................... 1038 Daewoo .............. 1004, 1005, 1006, 1016, 1017, 1018, 1127, 1171, 1196 Daytron ......................................................... 1004, 1006, 1171 Dimensia ........................................................................... 1000 Dumont ................................................................... 1004, 1151 Electroband ...................................................................... 1002 Electrohome ................. 1003, 1004, 1006, 1019, 1020, 1022 Emerson ............ 1004, 1006, 1012, 1023, 1024, 1025, 1026, 1027, 1028, 1029, 1030, 1031, 1032, 1033, 1034, 1035, 1036, 1037, 1038,1039, 1041, 1042, 1043, 1044, 1046, 1047, 1123, 1124, 1162, 1171, 1177, 1179, 1191, 1208 Envision .................................................................. 1004, 1006 Fisher ....................................... 1048, 1049, 1051, 1162, 1180 Fujitso ............................................................................... 1046 Funai ....................................................................... 1038, 1046 Futuretec ........................................................................... 1038 GE . 1000, 1003, 1004, 1006, 1022, 1052, 1054, 1055, 1087, 1164, 1165, 1166, 1167, 1168, 1181, 1213 Gibralter .................................................................. 1004, 1151 Goldstar ... 1004, 1005, 1006, 1012, 1019, 1056, 1057,1058, 1155, 1156, 1171, 1172 Grundy .......................................................... 1038, 1046, 1171 Hallmark ................................................................. 1004, 1006 Harvard ............................................................................. 1038 Hitachi .... 1004, 1006, 1012, 1013, 1014, 1059, 1060, 1061, 1135, 1136, 1137, 1138, 1139, 1140, 1141, 1142, 1143, 1144, 1145,1146, 1148, 1150, 1179, 1198, 1199 IMA ................................................................................... 1038 Infinity .............................................................................. 1062 JCPenney 1000, 1004, 1005, 1006, 1008, 1022, 1052, 1054, 1058, 1063, 1064, 1072, 1087, 1105, 1128, 1171, 1172, 1181, 1201 Janeil .................................................................................. 1174 JBL ..................................................................................... 1062 JCB .................................................................................... 1002 Jensen ..................................................................... 1004, 1006 JVC .......... 1012, 1013, 1014, 1054, 1060, 1065, 1066, 1067, 1157,1158, 1159, 1182 Kawasho ...................................................... 1002, 1004, 1006 Kenwood ...................................................... 1004, 1006, 1019 Kloss Novabeam ............................... 1068, 1069, 1174, 1183 KTV ..................................................... 1038, 1070, 1171, 1177 Loewe ................................................................................ 1062 Logik ................................................................................. 1083 Luxman ................................................................... 1004, 1006 LXI ................................ 1000, 1006, 1049, 1062, 1071, 1072, 1073, 1162, 1181, 1207 Magnavox ................... 1004, 1006, 1008, 1019, 1062, 1068, 1069, 1075, 1076, 1077, 1088, 1130, 1131, 1132, 1133, 1134, 1183, 1219, 1235 Majestic ............................................................................. 1083 Marantz .............................................. 1004, 1006, 1062, 1078 Megatron ................................................................ 1006, 1059 Memorex ................................. 1001, 1006, 1082, 1083, 1162 MGA ............................. 1004, 1005, 1006, 1019, 1022, 1051, 1079, 1080, 1082 Midland ..................................... 1054, 1151, 1171, 1172, 1181 Minutz ............................................................................... 1052 Mitisubishi ......... 1004, 1005, 1006, 1019, 1022, 1051, 1079, 1080, 1081, 1082, 1125 Montgomery Ward .......................................................... 1083 Motorola ................................................................. 1003, 1173 MTC .................................................... 1004, 1005, 1006, 1105 Multitech .......................................................................... 1038 Multivision ........................................................................ 1084 NAD ..................................................... 1006, 1071, 1072, 1185 NEC .......................................... 1003, 1004, 1005, 1006, 1200 Nikko ....................................................................... 1006, 1016 NTC ..................................................................................... 1016 Onwa ................................................................................. 1038 Optimus .............................................................................. 1185 Optonica ................................................................. 1095, 1173 Orion ....................................................................... 1035, 1191 Panasonic ................................ 1003, 1054, 1062, 1170, 1214 Philco ........................... 1003, 1004, 1005, 1006, 1008, 1012, 1019, 1062, 1068, 1069, 1075, 1077, 1183 Philips ............... 1003, 1004, 1008, 1012, 1019, 1062, 1068, 1069, 1075, 1076, 1086, 1087, 1088, 1089 Pilot ......................................................................... 1004, 1171 Pioneer ................ 1004, 1006, 1090, 1091, 1092, 1179, 1185 Portland ................................... 1004, 1005, 1006, 1016, 1171 Price Club .......................................................................... 1105 Prism ................................................................................. 1054 Proscan ................................................................... 1000, 1181 Proton ................................................ 1004, 1006, 1012, 1093 Pulsar ...................................................................... 1004, 1151 Quasar ................................................ 1003, 1054, 1070, 1094 Radio Shack/Realistic .......... 1000, 1004, 1006, 1012, 1038, 1049, 1095, 1162, 1171, 1172 RCA ................... 1000, 1003, 1004, 1005, 1006, 1007, 1019, 1096, 1098, 1099, 1100, 1101, 1102, 1103, 1129, 1179, 1181, 1187, 1188, 1190, 1202, 1203, 1215, 1233 Runco ................................................................................. 1151 Sampo ................................................ 1004, 1006, 1171, 1172 Samsung ............ 1004, 1005, 1006, 1012, 1015, 1019, 1104, 1105, 1106, 1171, 1172, 1204 Samsux .............................................................................. 1171 Sansui ................................................................................ 1191 Sanyo ............................ 1004, 1048, 1049, 1080, 1107, 1108, 1162, 1169, 1180 Scotch ............................................................................... 1006 Scott ................... 1004, 1006, 1012, 1024, 1035, 1038, 1046 Sears ........ 1000, 1004, 1006, 1013, 1014, 1019, 1046, 1048, 1049, 1051, 1066, 1071, 1072, 1109, 1110, 1162, 1180, 1181, 1189 Sharp ............................. 1004, 1006, 1012, 1029, 1095, 1111, 1112, 1113, 1122, 1171, 1173 Shogun .............................................................................. 1004 Signature ...................................................... 1001, 1083, 1115 Simpson ............................................................................ 1008 Sony .................................................. 1002, 1205, 1216, 1218 Soundesign ............................. 1004, 1006, 1008, 1038, 1046 Squareview ........................................................................ 1189 SSS .......................................................................... 1004, 1038 Starlite .............................................................................. 1038 Supre-Macy ....................................................................... 1174 Supreme ............................................................................ 1002 Sylvania ....................... 1004, 1006, 1008, 1019, 1062, 1068, 1069, 1075, 1076, 1077, 1088, 1116, 1161, 1183 Symphonic ................................................... 1033, 1038, 1189 Tandy ................................................................................. 1173 Tatung ............................................................................... 1003 Technics ............................................................................ 1054 Techwood ..................................................... 1004, 1006, 1054 Teknika ... 1004, 1005, 1006, 1008, 1012, 1013, 1014, 1016, 1038, 1046, 1076, 1082, 1083, 1105, 1170, 1171 Telecaption ........................................................................ 1117 TMK ......................................................................... 1004, 1006 Toshiba ........................... 1049, 1071, 1072, 1105, 1109, 1117, 1118, 1160, 1162 Totevision .......................................................................... 1171 Universal ................................................................. 1052, 1087 Victor ...................................................................... 1066, 1182 Vidtech ......................................................... 1004, 1005, 1006 Viking ................................................................................ 1174 Wards ................ 1000, 1001, 1004, 1005, 1006, 1019, 1024, 1033, 1046, 1052, 1062, 1068, 1069, 1075, 1076, 1083, 1087, 1088, 1095, 1119, 1120 Yamaha .............................................. 1004, 1005, 1006, 1019 Zenith ........ 1004, 1083, 1151, 1152, 1153, 1154, 1210, 1217 VCR (programmable to the VCR, AUX1 and AUX2 buttons) Admiral ........................................................................ 2132 Adventura .................................................................... 2026 Aiko ............................................................................. 2027 Aiwa ............................................................................. 2026 Akai ........ 2003, 2004, 2005, 2007, 2008, 2111, 2112, 2113 American High ............................................................ 2021 Asha ............................................................................. 2013 Audio Dynamics ................................................ 2009, 2010 Audiovox ..................................................................... 2014 Beaumark .................................................................... 2013 Bell & Howell ............................................................. 2011 Broksonic .......................................................... 2012, 2025 Calix ............................................................................. 2014 Candle ............. 2013, 2014, 2015, 2016, 2017, 2018, 2019 Canon ...................................................... 2021, 2022, 2114 Capehart ............................................................ 2020, 2110 Carver .......................................................................... 2062 CCE .................................................................... 2027, 2061 Citizen .... 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2027 Colortyme .................................................................... 2009 Colt .............................................................................. 2061 Craig .............................................. 2013, 2014, 2023, 2061 Curtis Mathes ...................... 2000, 2009, 2013, 2016, 2018, 2021, 2022, 2024, 2115, 2131 Cybernex ..................................................................... 2013 Daewoo . 2015, 2017, 2019, 2025, 2026, 2027, 2028, 2110 Daytron ........................................................................ 2110 DBX ................................................................... 2009, 2010 Dimensia ........................................................... 2000, 2131 Dynatech ..................................................................... 2026 Electrohome ...................................................... 2014, 2029 Electrophonic .............................................................. 2014 Emerson .......... 2012, 2014, 2015, 2021, 2024, 2025, 2026, 2029, 2030, 2031, 2032, 2033, 2034, 2035, 2036, 2037, 2038, 2039, 2040, 2041, 2042, 2044, 2045, 2046, 2047, 2065, 2113, 2116, 2117, 2130 Fisher ..... 2011, 2023, 2048, 2049, 2050, 2051, 2052, 2118 Fuji ..................................................................... 2021, 2119 Funai ............................................................................ 2026 Garrard ........................................................................ 2026 GE ....................................... 2000, 2001, 2013, 2021, 2022, 2053, 2115, 2120, 2131 Goldstar ......................................... 2009, 2014, 2018, 2054 Gradiente ..................................................................... 2026 Harley Davidson ......................................................... 2026 Harman Kardon .......................................................... 2009 Harwood ..................................................................... 2061 Headquarter ................................................................ 2011 Hi-Q ............................................................................. 2023 Hitachi ............. 2055, 2056, 2057, 2107, 2111, 2120, 2122 Instant Replay ............................................................. 2021 JCPenney ........ 2009, 2010, 2011, 2013, 2014, 2021, 2022, 2055, 2056, 2058, 2059, 2060, 2107, 2118 JCL ............................................................................... 2021 Jensen ...................................................... 2055, 2056, 2111 JVC ............................. 2009, 2010, 2011, 2018, 2111, 2123 Kenwood ......... 2009, 2010, 2011, 2016, 2018, 2111, 2123 KLH .............................................................................. 2061 Kodak ................................................................ 2014, 2021 Lloyd ............................................................................ 2026 Logik ............................................................................ 2061 LXI ............................................................................... 2014 Magnavox ........................... 2021, 2022, 2062, 2063, 2104, 2105, 2108, 2124 Magnin ......................................................................... 2013 Marantz .. 2009, 2010, 2011, 2016, 2018, 2021, 2062, 2064 Marta ............................................................................ 2014 Masushita ..................................................................... 2021 MEI .............................................................................. 2021 Memorex ............................ 2011, 2013, 2014, 2021, 2023, 2026, 2104, 2132 MGA ......................................................... 2029, 2065, 2113 MGN Technology ........................................................ 2013 Midland ........................................................................ 2053 Minolta ..................................................... 2055, 2056, 2107 Mitsubishi ....... 2029, 2055, 2056, 2065, 2066, 2067, 2068, 2069, 2070, 2071, 2072, 2073, 2074, 2106, 2113, 2123 Montgomery Ward ............................................ 2075, 2132 Motorola ............................................................ 2021, 2132 MTC ................................................................... 2013, 2126 Multitech .............................. 2013, 2016, 2026, 2053, 2061 Continues on next page... Chapter 2 13 Code List NEC ....... 2009, 2010, 2011, 2016, 2018, 2064, 2076, 2078, 2079, 2111, 2123 Nikko ........................................................................... 2014 Noblex ......................................................................... 2013 Olympus ...................................................................... 2021 Optimus ............................................................. 2014, 2132 Optonica ...................................................................... 2096 Panasonic .................. 2021, 2022, 2109, 2125, 2126, 2127 Pentax .................................. 2016, 2055, 2056, 2107, 2120 Pentex Research .......................................................... 2018 Philco ............................................. 2021, 2022, 2062, 2063 Philips ............................................ 2021, 2062, 2096, 2124 Pilot .............................................................................. 2014 Pioneer ................................ 2010, 2055, 2080, 2081, 2123 Portland ......................................... 2016, 2017, 2019, 2110 Proscan .................................................... 2000, 2001, 2131 Protec ........................................................................... 2061 Pulsar ........................................................................... 2104 Quarter ........................................................................ 2011 Quartz .......................................................................... 2011 Quasar ..................................................... 2021, 2022, 2125 Radio Shack/Realistic ......... 2011, 2013, 2014, 2021, 2022, 2023, 2026, 2029, 2049, 2050, 2096, 2132 Radix ............................................................................ 2014 Randex ......................................................................... 2014 RCA ..................................... 2000, 2001, 2003, 2013, 2021, 2055, 2056, 2082, 2083, 2084, 2085, 2086, 2087, 2088, 2089, 2090, 2091, 2107, 2115, 2120, 2125, 2131, 2133 Ricoh ............................................................................ 2128 Runco .......................................................................... 2104 Samsung .................... 2005, 2013, 2015, 2033, 2053, 2112 Sanky ................................................................. 2104, 2132 Sansui ............................................ 2010, 2092, 2111, 2123 Sanyo ....................................................... 2011, 2013, 2023 Scott ....... 2012, 2015, 2025, 2032, 2038, 2065, 2093, 2116 Sears ............... 2011, 2014, 2021, 2023, 2048, 2049, 2050, 2051, 2055, 2056, 2107, 2118 Sharp ................ 2017, 2029, 2094, 2095, 2096, 2097, 2132 Shintom ......................................... 2004, 2056, 2061, 2098 Shogun ........................................................................ 2013 Signature ...................................................................... 2132 Singer ....................................................... 2021, 2061, 2128 Sony ............................................... 2004, 2098, 2099, 2119 STS ..................................................................... 2021, 2107 Sylvania ........... 2021, 2022, 2026, 2062, 2063, 2065, 2124 Symphonic ................................................................... 2026 Tandy ........................................................................... 2011 Tashiko ........................................................................ 2014 Tatung .......................................................................... 2111 Teac ......................................................... 2026, 2085, 2111 Technics ............................................................. 2021, 2109 Teknika ................................ 2014, 2021, 2026, 2100, 2129 TMK ......................................................... 2013, 2024, 2047 Toshiba ............ 2015, 2049, 2051, 2055, 2065, 2093, 2116 Totevision .......................................................... 2013, 2014 Unitech ........................................................................ 2013 Vector Research ............................. 2009, 2010, 2015, 2016 Victor ........................................................................... 2010 Video Concepts ................... 2009, 2010, 2015, 2016, 2113 Videosonic ................................................................... 2013 Wards .... 2013, 2014, 2015, 2021, 2023, 2026, 2029, 2055, 2056, 2061, 2096, 2101, 2102, 2103, 2107, 2116, 2132 XR-1000 ................................................... 2021, 2026, 2061 Yamaha ................................ 2009, 2010, 2011, 2018, 2111 Zenith .................................. 2004, 2098, 2104, 2119, 2128 DVD (programmable to the DVD, AUX1 and AUX2 buttons) Aiwa ............................................................................. 3009 Apex .................................................................. 3023, 3024 GE ................................................................................ 3000 Hitachi ......................................................................... 3008 JVC ..................................................................... 3002, 3010 Konka ................................................................ 3011, 3012 Magnavox .................................................................... 3003 Mitsubishi .................................................................... 3004 Panasonic .................................................................... 3013 Philips ............................................ 3003, 3019, 3021, 3022 Pioneer ........................................................................ 3005 Proscan ........................................................................ 3000 RCA .................................................................... 3000, 3001 Samsung ...................................................................... 3025 Sanyo ........................................................................... 3014 Sony ......................................................... 3006, 3015, 3016 Toshiba .................................................... 3007, 3017, 3020 Zenith .......................................................................... 3018 Cable Boxes (programmable to the AUX1 and AUX2 buttons) ABC ...................................... 5002, 5003, 5004, 5006, 5053 Antronix ............................................................. 5008, 5009 Archer ...................................................... 5008, 5009, 5010 Cabletenna .................................................................. 5008 Cableview .................................................................... 5008 Colour Voice ...................................................... 5012, 5013 Comtronic .................................................................... 5014 Contec ......................................................................... 5016 Eastern ......................................................................... 5017 GC Electronics ............................................................. 5009 GE ...................................................................... 5000, 5001 Gemini ............................................................... 5018, 5019 General Instrument ..................................................... 5003 Hamlin ....................... 5020, 5021, 5022, 5028, 5035, 5045 Hitachi ......................................................................... 5003 Jerrold ........................ 5003, 5018. 5023, 5024, 5046, 5053 Magnavox .................................................................... 5025 Memorex ..................................................................... 5026 Movie Time ................................................................. 5027 NEC .............................................................................. 5005 NSC .............................................................................. 5027 Oak .................................................................... 5016, 5029 Panasonic .......................................................... 5048, 5052 Philips ................................. 5011, 5012, 5013, 5015, 5019, 5025, 5030, 5031, 5032 Pioneer .............................................................. 5033, 5034 Proscan .............................................................. 5000, 5001 RCA ................................................ 5007, 5047, 5049, 5052 Realistic ........................................................................ 5009 Regal .................................................................. 5022, 5035 Regency ....................................................................... 5017 Rembrandt ................................................................... 5003 Samsung ...................................................................... 5034 Scientific Atlanta ............................ 5006, 5036, 5037, 5038 Signal ........................................................................... 5018 Signature ...................................................................... 5003 Sprucer ........................................................................ 5052 Standard Components ...................................... 5039, 5044 Starcom .............................................................. 5018, 5053 Stargate ........................................................................ 5018 Starquest ...................................................................... 5018 Tocom ................................................................ 5004, 5023 Tusa ............................................................................. 5018 TV86 ............................................................................ 5027 Unika ................................................................. 5008, 5009 United Cable ............................................................... 5053 Universal .................................................. 5008, 5009, 5010 Viewstar ............................................................. 5025, 5027 Zenith ................................................................ 5050, 5051 RCA & Dimensia Audio Components (programmable to the AUX1 and AUX2 buttons) AM/FM ............................................................... 4003, 4270 Aux .............................................................................. 4004 CD ............................................................ 4007, 4190, 4211 Phono .......................................................................... 4005 Tape ............................................................................. 4006 Audio Receivers (programmable to the AUX1 and AUX2 buttons) Aiwa ....... 4261, 4262, 4263, 4264, 4265, 4266, 4267, 4277 Denon .......................................................................... 4283 Harmon Kardon .......................................................... 4276 JVC ............................................................................... 4268 JVL ............................................................................... 4276 Kenwood ..................................................................... 4269 Onkyo .......................................................................... 4278 Optimus ....................................................................... 4284 Panasonic .......................................................... 4279, 4280 Pioneer ........................................................................ 4275 RCA .............................................................................. 4270 Sherwood .................................................................... 4282 Sony ......................................................... 4271, 4272, 4281 Technics ............................................................. 4279, 4280 Wards ........................................................................... 4275 Yamaha .............................................................. 4274, 4275 Satellite Receivers (programmable to the AUX1 and AUX2 buttons) Dishnet ........................................................................ 5078 Echostar ....................................................................... 5089 GE ...................................................................... 5000, 5001 Proscan .............................................................. 5000, 5001 RCA ...................................... 5000, 5001, 5071, 5080, 5081 14 Chapter 2 Chapter 3: Satellite Receiver Features Active profile Current time and date The Program Guide The diagram on the left shows you the kind of information you see in the program guides. You can access a toolbar at the bottom of the program guide by pressing the FETCH button while in the guide (see the Toolbar section at the bottom of this page). Selectable Advertisements, available when ads are turned on in the guides (highlight and select for more information). Program titles and information Displaying the Program Guide You can quickly access the receiver's Default Guide by pressing the GUIDE button on the remote. To access other program guides, press MENU on the remote control and select Program Guides, then the guide of your choice (Channel, Logo, Category, etc.). You can also access the receiver's default guide by selecting Go to Guide from the Program Guides menu. To change the current user, press the remote control's WHO·INPUT button while viewing programming, then use the remote control's arrow and SELECT buttons to select the desired profile. You can also change the current profile by choosing Profile Guide from the Program Guides menu. Displaying the Toolbar To display the toolbar in the grid and detail guides, press FETCH while you're in the guide. The diagram on the right shows you the options available in the toolbar. Viewing Suggestions Channel Sort AlphaSortTM Channel Display ScoutTM To highlight the option you want, use the left and right arrows. To select the highlighted option, press SELECT. To clear the toolbar from the guide without making a selection, press FETCH again. Category Guide Chapter 3 15 Satellite Receiver Features The Channel Banner The channel banner appears whenever you do one of the following: · · · · Tune to a channel. Press the remote control's INFO, DIRECTV, or GO BACK buttons while watching programming. Press the up arrow, down arrow, or INFO on the satellite receiver's front panel. Exit the on-screen menu system (except when you press the CLEAR button on your remote control). The size of the banner depends on your choice in the Channel Banner Size control panel. The medium channel banner is shown on this page. The full banner (the medium banner, plus a description of the program you're watching if one's available) appears when you press INFO, regardless of your choice in the Channel Banner Size control panel. On-screen icons represent frequently-used menu items. Some icons also change appearance to show the item's status. Use the arrow buttons and SELECT to choose an icon. Active Profile Program titles and information Interactive content indicator Alternate Audio indicator Main menu AlphaSortTM ScoutTM Mailbox Caller ID Viewing suggestions Alternate audio Category Guide System lock/unlock Buttons of the Channel Banner Main Menu icon Takes you to the Main menu. Locked icon The system is locked. Spending, viewing and other limits cannot be accessed or changed. Selecting this icon displays a password menu. Enter the correct system password to override settings. Unlock icon The system is unlocked. Spending, viewing and other limits can be accessed or changed. Selecting this icon in the channel banner displays the Lock System control panel. Video Unlock icon A password has been entered to temporarily override the limits. The system will remain unlocked until the satellite receiver is turned off or re-locked. Program Unlock icon A password has been entered to override limits for a single program. After the program ends, or when the channel is changed, limits are restored. AlphaSortTM icon Enables you to sort titles alphabetically. ScoutTM icon Allows you to search for programs using key words. Mail icon Displays the Mail screen. The icon will be white if you have an unread mail. Telephone icon Displays the Caller ID list screen. The icon will be white if you have received a new call but have not accessed the Caller ID List screen. It will be gray if you have accessed the Caller ID List screen. Viewing Suggestions icon Displays the Viewing Suggestions menu. Category Guide icon Lets you search for programs matching a particular category or subcategory. Alternate Audio icon Cycles through the alternate audio choices. 16 Chapter 3 Satellite Receiver Features The DIRECTV INTERACTIVETM Feature Your digital satellite receiver includes DIRECTV INTERACTIVE, powered by Wink Communications®, a free service that gives you the opportunity to interact with TV programming and advertising. You can use your remote control to get programrelated information, respond to free offers during commercials and even make purchases while you watch TV. To use this feature, you must have your receiver plugged directly into a telephone outlet (or into a compatible wireless modem). TM Whenever you see the DIRECTV INTERACTIVE icon ( interactive window. ) appear, press the SELECT/i button on the remote control to open the To learn more about the DIRECTV INTERACTIVE service: 1. Press MENU on the remote control (the Main menu appears). 2. Use the arrow buttons on the remote control to highlight Interactive. 3. Press SELECT/i to tune directly to the DIRECTV INTERACTIVE Center (channel 499) to get more information about the following: Getting Started, Interactive Channels, Shopping Sign Up, Order History, Messages, Help & Settings, and About DIRECTV. © 2002 Wink Communications. All rights reserved. Wink Communications and the Wink logo are registered trademarks of Wink Communications, Inc. Displaying On-screen Guides Each time you press the remote control's GUIDE button, a different type of program guide appears: The Detail Guide The Detail Guide shows six channels (four with the toolbar) in a time-and-channel format, with program information for the highlighted program. A small window showing the program you were watching before entering the program guides is displayed in the upper left hand corner (you can preview other channels in the Detail Guide by highlighting channel numbers instead of the program titles). Notes: By default, the Detail Guide appears when you press GUIDE on the remote control. You can change the default guide from the Detail Guide to the Grid Guide. Select Personal Settings from the Main menu, then select the profile to be changed, then select Default Guide. Use the remote control's arrow buttons to highlight Grid Guide, then press the SELECT button to activate your choice. The Grid Guide The Grid Guide shows nine channels (seven with the toolbar) in a time-and-channel format. A small window showing the program you were watching before entering the program guides is displayed in the upper left hand corner (you can preview other channels in the Grid Guide by highlighting channel numbers instead of the program titles). Chapter 3 17 Satellite Receiver Features Getting Around In the Guides VCR ON OFF TV This section describes how to change channels and move around a program guide. DVD AUX1 AUX2 DIRECTV Digit Buttons (0­9) You can point quickly to any channel in the program guide by entering the channel number with the digit buttons (0­9). For example, to point to channel 228, press the digits 2-2-8, on the remote control. MUTE CH + SKIP VOL Scrolling Channel By Channel CH Buttons VOL FETCH GUIDE CH - GO BACK INFO The programs that you see on the TV screen make up one section--or page--of the total program guide. You can scroll one line at a time using the arrows: point to other times with the left and right arrows; point to other channels with the up and down arrows. (-) Scrolling Page By Page If you want to scroll up or down through the program guide faster, press the CH buttons on the remote control. The highlight scrolls a page at a time. MENU CLEAR Arrow Buttons Scrolling Forward and Reverse To scroll forward one page at a time, press the remote control's PLAY button while in DIRECTV mode. To go forward or reverse by a 6-hour block of time, use the FORWARD and REVERSE buttons on the remote control. 1 4 7 2 5 8 0 3 6 9 ANTENNA