User's Manual (GB) Manuel utilisateur (FR) Bedienungsanleitung (DE) Manuale d'uso (IT) Manual de uso (ES) Gebruikershandleiding (NL) Uëivatelská pàíruäka (CZ) Príruäka pouëívatea (SK) English English 1 Introduction Congratulations! Your Home Theatre Master 1000 (HTM1000) is a state-of-the-art device which integrates many different infrared remote controls to deliver instant A/V action to your fingertips. We hope that you love this remote and take it as your Personal Digital Assistant for your Home Theatre system. Before operating the remote, please read thoroughly this manual. Then, reserve it for future reference. 1.2 Getting to know your Home Theatre Master 1000 1. 2. 3. 4. 5. Infra-red lens Bright-blue LED indicator Touch screen panel Hard keys Battery compartment For Touch Screen panel: 6. 7. 8. 9. 10. Device mode keys (for device mode selection) Function keys (for remote operation) MUTE key (for TV volume shut down) SHIFT key (for secondary function) PAGE key (for next group function keys) 1.1 Key Features · Pre-programmed with learning capability · 5-in-1 high end Home Theatre remote (support TV, VCR, SAT, CBL and DVD) · Maximum of 226 learning commands · Bright-blue backlight LCD display panel · Segment-typed display panel with 24 touch-sensitive squares · Quick set up by code entering and library code search · Macro function performed by up to 6 programmable smart keys · Volume punch through control for TV · Teletext and Fastext control available for digital TV · Auto power off (Sleep mode) for battery conservation 1 2 6 3 9 7 10 8 5 VOL+ PVOLP+ 4 1 2 English English 1.3 Specifications Operation System: Compatibility: Integrated preprogrammed & learning infra-red remote control system Preprogrammed with code library of Televisions (TVs), Video Cassette Recorders (VCRs), Satellite / Digital Satellite Receivers (SATs), Cable Converters (CBLs) and Digital Video Disc Players (DVDs) 226 learning commands Non-volatile and permanent memory Negative touch screen LCD Bright-blue EL backlight 8 metres (25 feet) 4 x AAA size batteries (Alkaline is recommended) 163 x 54 x 19.5 mm 130g (without batteries installed) 180g (with batteries installed) 2 u Getting Start After installed batteries, your HTM1000 prompts at TV mode. If it is in-active for about 15 seconds, it goes to power saving (sleep) mode and shut down the display. Simply, touch the screen panel to activate the unit again. Note: When in power saving (sleep) mode, the hard key section is still available for command. Tap any of the Device Mode Key on the screen to enter the corresponding device mode. e.g. . The " " icon will change to blue color. Tap a key directly to send out the corresponding infra-red command. Memory Capacity: Memory Retention after Battery Disconnection: Display Panel: EL Backlighting: Operating Distance: Power Requirement: Dimensions: Weight : u u 2.1 Hard Keys There are 9 hard keys. They transmit IR command corresponding to the selected device. · · · · · · · · · P+ P­ VOL+ VOL­ GREEN RED YELLOW BLUE Power ON/OFF Program up or channel up Program down or channel down Volume up Volume down For teletext and fastext function For teletext and fastext function For teletext and fastext function For teletext and fastext function For improvement purposes, specifications and functions are subjected to change without priority notice. 1.4 How to Install Batteries Alkaline batteries are recommended. 1. Open the battery cover. 2. Follow the polarity symbol shown in the battery compartment. 3. Place the batteries inside. 4. Replace the battery cover. (Remark: G/R/Y/B buttons are also used for supporting some Satellite Receivers and Cable box) 2.2 Key Tone When you tap any key, there is a short beep sound. 2.3 Backlight Note: Battery Low If the icon " " is shown on the display panel, it shows that the battery level is low. You must replace the battery with a new one to ensure proper functioning. Do not use old and new batteries together as old batteries tend to leak. Bright-blue EL Backlight will be turned on once you tap the remote. The backlight will be turned off automatically if the remote is not active for 15 seconds. 3 4 English English 3 How to Set Up the Home Theatre Master 1000 You may setup the remote by the following code entering instructions. 1. Refer to the Device Code List, look up the 4-digit device code which corresponds to the brands of your A/V equipment. If there are more than one device code listed under your brand, try from the first code. 2. Turn on your device manually (e.g. TV). 3. Press a desired device mode key (e.g. ," " icon will change into blue color) 4. Hold down " P+ " and " VOL­ " on the remote simultaneously for 3 seconds until the indicator lights up. 5. Input the 4-digit device code, the indicator will flash twice and turn off if successful. Turn on your device (e.g. TV), try the function keys on the remote. If your device (e.g. TV) responds to your selected function correctly, you have entered the right device code. Otherwise, repeat the above setup instructions with the rest available device codes until your device (e.g. TV) responds to your selected function, and most keys work correctly. * Simply repeat the above procedures to enter the device codes for your VCR, SAT, DVD or CBL. (Remember to press a correct device mode key in step 3 above.) 3.2 By Searching Through the Library If you cannot identify a correct device code for your equipment from the Device Code List, you may search the code through the library: 1. Turn on your device manually (e.g. TV). 2. Press a desired device mode key (e.g. ) 3. Hold down " P+ " and " VOL­ " on the HTM1000 simultaneously for 3 seconds until the indicator lights up. 4. Enter a corresponding Magic Search Code from the following table. The indicator will flash twice and turn off. DEVICE TYPE: TV VCR SAT CBL DVD 3.1 By Entering Device Code MAGIC SEARCH CODE: 0001 0002 0003 0004 0005 (e.g. press device mode key, then press " P+ " and " VOL­ ", and enter TV Magic Search Code 0001.) 5. Press the same desired device mode key again as in step 2 above. (e.g. ) 6. Hold down " P+ " and " VOL­ " simultaneously for 3 seconds until the indicator lights up, and your HTM1000 is ready to start searching. 7. Aim the remote at your device (e.g. TV), press the " " key repeatedly, slowly and patiently until the device has been turned off. Once your device has been turned off, immediately press the device mode key (e.g. ) to lock in code and the indicator flashes twice and then turn off. * Simply repeat the above setup procedures to search the device code for your VCR, SAT, DVD or CBL.. (Remember to press a correct device mode key and correct Magic Search Code in step 2­5 above.) Note: ­ DVD, CBL, SAT and other device codes can be entered into any device modes except "TV" & "VCR" modes. Just simply press the device mode key and enter your 4-digit device code for DVD, CBL, SAT and other devices. ­ If the indicator flashes 6 times in step 5, a wrong device code has been entered. You are required to repeat step 2 to 5 again. IMPORTANT: ­ If the power on/off function of your device is not infrared controlled -- you need to follow step 2 to 6 above and start searching:­ Press " " and another important function key alternately until your device responds to the expected function, press the device mode key (e.g. ) to lock in the code. e.g. Press " " & " 1 " alternately, or Press " "&" " alternately. Suggestion: ­ If you cannot find a correct device code for your equipment, see " 3.2 By Searching Through the Library ". Note: ­ DVD, CBL and other device codes can be searched and locked into any device modes except "TV" & "VCR" modes. Just simply press the corresponding device mode key in step 2 & 5 and enter an appropriate Magic Search Code for your DVD, CBL and other devices. 5 6 English ­ Each time you press the " ", the HTM1000 will skip to the next code and send out a POWER signal trying to turn off your device. If you failed to stop pressing " " in time when your device has been turned off, turn on your device again immediately. Before the indicator goes out, press " P­ " on the HTM1000 to skip backward. Repeat the step 7 above and lock in code. ­ If the indicator flashes 6 times after your pressing of " " key, you are already at the last code of the library. Press the device mode key (e.g. ) to resume the HTM1000 and repeat carefully the above procedures to search again. English 7. Repeat steps 5 to 6 to transfer other signals into next function key. When you finish the whole device mode, press the same device mode key (e.g. ) again to store your setting. The indicator will flash twice and then turn off. 4.1 Learning Additional Codes by "SHIFT" There are in maximum of 42 squares within 3 pages which are available to be learnt for each device mode. In case you would like to learn more than 42 commands per each device, you can make use of " SHIFT " function to obtain additional 3 more pages in order to obtain additional 42 free learning spaces under " SHIFT " platform. For detail explanation of how to use the " SHIFT " function, please refer to section " 5.3 SHIFT " for reference. 4 How to Set Up Your HTM1000 (Learning Commands) 4.2 Advance Learning ­ Teaching a Dual Signal If you found a learned command work for your A/V equipment only occasionally, your original remote control may contain dual signals. Try the following steps to reprogram this command:­ 1. Follow step 1 to 4 of " 4 How to Set Up Your HTM1000 (Learning Commands) ". 2. Press and release a desired key on the HTM1000 you want to hold the command. The device mode key icon (e.g. ) will stop flashing. 3. Press and hold the corresponding key on your A/V remote control to transfer the command. The indicator will flash once and the device mode key icon (e.g. ) will flash again. The first signal has been transferred successfully and you can release the key on the A/V remote control. 4. Press and release the same button on the HTM1000 again. The device mode key icon (e.g. ) will stop flashing. 5. Press and hold the same corresponding key on your A/V remote control until the indicator will flash once and the device mode key icon (e.g. ) flash again. The dual signal command has been transferred successfully. 6. Repeat steps 2 to 5 of this procedure to transfer other signals if there is any. 7. When finished, press the same device mode key again to store your setting. Warning: Entering a new preprogrammed device code will automatically erase and replace all learned commands in the chosen device mode. Your HTM1000 is factory preprogrammed to operate your TVs, VCRs, SATs, CBLs & DVDs. Due to the limited number of key, some minor functions may not be included. You may teach your remote with the original A/V remote to operate any excluded function by your choice. Besides the preprogrammed devices, you may also teach the remote to operate other infra-red controlled equipment and appliances, such as HiFi or air-conditioners, etc. Your HTM1000 can learn and reproduce up to 226 commands from other remote controls. All 5 device modes (TV, VCR, DVD, SAT, CBL) can be taught to operate additional commands:­ 1. Press a desired device mode key (e.g. ," " icon will change into blue color). 2. Hold down " P+ " & " VOL­ " on the remote together simultaneously for 3 seconds until the indicator lights up. 3. Enter the Magic Learn Code ­ 0000, the " Learn " icon will light up and your HTM1000 is ready to learn commands. 4. Aim your A/V remote control to the HTM1000 infra-red lens on a flat surface, with 5-8 cm apart. Make sure your A/V remote control has new batteries. 5. Press and release a desired keys on the remote you want to hold the command. 6. Press and hold the corresponding key on your A/V remote control to transfer the command. The indicator will flash once and the device mode key icon (e.g. ) will flash again when the command is copied. You can release the key on the A/V remote control. If the indicator flashes 6 times, it shows error in learning process. Adjust the position of both remote controls and repeat steps 5 to 6 again. 7 Note: ­ Do not attempt to learn additional commands with the Device Mode Keys, " Page " Key & " SHIFT " Key. They will not hold commands by themselves. 8 English ­ Each function key will hold one command only, a new command to be learnt will automatically erase and replace the previous one. ­ If you have accidentally pressed an unexpected key in step 5 above, you have to wait 16 seconds until the indicator goes out and the HTM1000 will go back to normal operation. You may repeat the above procedures to setup the remote again. ­ If the indicator flashes 3 times during the transference of the signals, this tells you the memory bank is full. Press the same device key again to resume normal operation. (You may erase the learned commands in a device mode and make room for ...