User manual ROLAND GR-20

Owner's Manual Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (p. 2­3, p. 4). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2004 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. USING THE UNIT SAFELY Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. * Material damage refers other adverse effects respect to the home furnishings, as well animals or pets. to damage or caused with and all its to domestic The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled. The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet. 001 009 · Before using this unit, make sure to read the instructions below, and the Owner's Manual. .......................................................................................................... 002c · Do not open (or modify in any way) the unit or its AC adaptor. .......................................................................................................... 003 · Do not excessively twist or bend the power cord, nor place heavy objects on it. Doing so can damage the cord, producing severed elements and short circuits. Damaged cords are fire and shock hazards! .......................................................................................................... 010 · Do not attempt to repair the unit, or replace parts within it (except when this manual provides specific instructions directing you to do so). Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the "Information" page. .......................................................................................................... 004 · Never use or store the unit in places that are: · Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heat-generating equipment); or are · Damp (e.g., baths, washrooms, on wet floors); or are · Humid; or are · Exposed to rain; or are · Dusty; or are · Subject to high levels of vibration. .......................................................................................................... 007 · This unit, either alone or in combination with an amplifier and headphones or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level, or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should immediately stop using the unit, and consult an audiologist. .......................................................................................................... 011 · Do not allow any objects (e.g., flammable material, coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit. .......................................................................................................... 012b · Immediately turn the power off, remove the AC adaptor from the outlet, and request servicing by your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the "Information" page when: · The AC adaptor, the power-supply cord, or the plug has been damaged; or · If smoke or unusual odor occurs · Objects have fallen into, or liquid has been spilled onto the unit; or · The unit has been exposed to rain (or otherwise has become wet); or · The unit does not appear to operate normally or exhibits a marked change in performance. · Make sure you always have the unit placed so it is level and sure to remain stable. Never place it on stands that could wobble, or on inclined surfaces. .......................................................................................................... 008c · Be sure to use only the AC adaptor supplied with the unit. Also, make sure the line voltage at the installation matches the input voltage specified on the AC adaptor's body. Other AC adaptors may use a different polarity, or be designed for a different voltage, so their use could result in damage, malfunction, or electric shock. 2 013 101b · In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit. .......................................................................................................... 014 · The unit and the AC adaptor should be located so their location or position does not interfere with their proper ventilation. .......................................................................................................... 102c · Protect the unit from strong impact. (Do not drop it!) .......................................................................................................... 015 · Always grasp only the plug on the AC adaptor cord when plugging into, or unplugging from, an outlet or this unit. .......................................................................................................... 103b · Do not force the unit's power-supply cord to share an outlet with an unreasonable number of other devices. Be especially careful when using extension cords--the total power used by all devices you have connected to the extension cord's outlet must never exceed the power rating (watts/amperes) for the extension cord. Excessive loads can cause the insulation on the cord to heat up and eventually melt through. .......................................................................................................... 016 · At regular intervals, you should unplug the AC adaptor and clean it by using a dry cloth to wipe all dust and other accumulations away from its prongs. Also, disconnect the power plug from the power outlet whenever the unit is to remain unused for an extended period of time. Any accumulation of dust between the power plug and the power outlet can result in poor insulation and lead to fire. .......................................................................................................... 104 · Before using the unit in a foreign country, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the "Information" page. · Try to prevent cords and cables from becoming entangled. Also, all cords and cables should be placed so they are out of the reach of children. .......................................................................................................... 106 · Never climb on top of, nor place heavy objects on the unit. .......................................................................................................... 107c · Never handle the AC adaptor or its plugs with wet hands when plugging into, or unplugging from, an outlet or this unit. .......................................................................................................... 108b · Before moving the unit, disconnect the AC adaptor and all cords coming from external devices. .......................................................................................................... 109b · Before cleaning the unit, turn off the power and unplug the AC adaptor from the outlet (p. 10). .......................................................................................................... 110b · Whenever you suspect the possibility of lightning in your area, disconnect the AC adaptor from the outlet. 3 IMPORTANT NOTES 291a In addition to the items listed under "USING THE UNIT SAFELY" on page 2­3, please read and observe the following: Power Supply 301 Repairs and Data 452 · Do not use this unit on the same power circuit with any device that will generate line noise (such as an electric motor or variable lighting system). 302 · The AC adaptor will begin to generate heat after long hours of consecutive use. This is normal, and is not a cause for concern. 307 · Before connecting this unit to other devices, turn off the power to all units. This will help prevent malfunctions and/or damage to speakers or other devices. · Please be aware that all data contained in the unit's memory may be lost when the unit is sent for repairs. Important data should always be backed up in another MIDI device (e.g., a sequencer), or written down on paper (when possible). During repairs, due care is taken to avoid the loss of data. However, in certain cases (such as when circuitry related to memory itself is out of order), we regret that it may not be possible to restore the data, and Roland assumes no liability concerning such loss of data. Placement 351 Additional Precautions 551 · Using the unit near power amplifiers (or other equipment containing large power transformers) may induce hum. To alleviate the problem, change the orientation of this unit; or move it farther away from the source of interference. 352a · Please be aware that the contents of memory can be irretrievably lost as a result of a malfunction, or the improper operation of the unit. To protect yourself against the risk of losing important data, we recommend that you periodically save a backup copy of important data you have stored in the unit's memory in another MIDI device (e.g., a sequencer). 552 · This device may interfere with radio and television reception. Do not use this device in the vicinity of such receivers. 352b · Noise may be produced if wireless communications devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off. 354a · Unfortunately, it may be impossible to restore the contents of data that was stored in another MIDI device (e.g., a sequencer) once it has been lost. Roland Corporation assumes no liability concerning such loss of data. 553 · Use a reasonable amount of care when using the unit's buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions. 556 · Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit. 355b · When connecting / disconnecting all cables, grasp the connector itself--never pull on the cable. This way you will avoid causing shorts, or damage to the cable's internal elements. 558a · When moved from one location to another where the temperature and/or humidity is very different, water droplets (condensation) may form inside the unit. Damage or malfunction may result if you attempt to use the unit in this condition. Therefore, before using the unit, you must allow it to stand for several hours, until the condensation has completely evaporated. · To avoid disturbing your neighbors, try to keep the unit's volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those around you (especially when it is late at night). 559a · When you need to transport the unit, package it in the box (including padding) that it came in, if possible. Otherwise, you will need to use equivalent packaging materials. 562 Maintenance 401a · Use a cable from Roland to make the connection. If using some other make of connection cable, please note the following precautions. · Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable. · For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth. 402 · Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation. 220 * All product names mentioned in this document are trademarks or registered trademarks of their respective owners. 4 Introduction The GR-20 is a guitar synthesizer (guitar synth) which contains a high-quality sound generator and is designed for easy operation. The GR-20 carefully analyses the pitch and volume of each string as it tracks the signals being output by the divided pickup (a pickup installed on your guitar which outputs a separate signal for each string), and uses this information to trigger its built-in sound generator. At the same time, a data stream interpreting your guitar performance can also be transmitted via the MIDI OUT connector, and used to play an external MIDI device, such as a sound module. Main Features · You can play more than 450 different types of synth sounds in the same way as when playing your guitar conventionally. · In addition to playing the synth sounds by themselves, you can combine the normal guitar sound with the synth sound. · When applying an external effects unit to the normal guitar sound, you can use the Mix In jack to mix the processed sound with the synth sound. · The GR-20 can be used with any steel-string guitar on which a GK-3 or GK-2A (divided pickup; sold separately) can be correctly installed. · The GR-20 can also be used with a bass guitar on which a GK-3B or GK-2B (divided pickup for bass guitar; sold separately) is installed. · Built-in effects (reverb, delay, chorus) are provided for the synth sound, creating a rich and spacious ambiance. (p. 20) · You can adjust and store settings such as attack and decay time, and effect depth. (p. 20) · You can use the GR-20's two foot pedals to apply a Hold effect or Glide effect. (p. 15) · Use the built-in expression pedal to control parameters such as volume or filter. (p. 16) · Since your guitar performance is output as MIDI data, you can use your guitar to play an external sound module or as an input device for your MIDI sequencer. (p. 28) · A guitar tuner is built-in for quick and accurate tuning. (p. 13) 5 Contents USING THE UNIT SAFELY......................................................................2 IMPORTANT NOTES ...............................................................................4 Introduction .............................................................................................5 Main Features.............................................................................................................................................. 5 Names of Things and What They Do.....................................................8 Front Panel................................................................................................................................................... 8 Rear Panel .................................................................................................................................................. 10 Chapter 1 Play the Sounds! .................................................................11 Preparing Your Guitar ............................................................................................................................. 11 Connections ............................................................................................................................................... 11 Turning the Power On ............................................................................................................................. 12 Adjusting the Output Level .................................................................................................................... 12 Adjusting the Input Sensitivity (GK SENS).......................................................................................... 12 Tuning Your Guitar (Tuner Function)................................................................................................... 13 Specifying the Output Device (OUTPUT SELECT)............................................................................. 14 Selecting a Sound (Patch) ........................................................................................................................ 14 Using the Knob to Select Patches................................................................................................ 14 Using the Switches of the GK Pickup to Select Patches .......................................................... 15 Using the Foot Pedals to Select Patches ..................................................................................... 15 Using an External Device Via MIDI to Select Patches ............................................................. 15 Play the GR-20! ......................................................................................................................................... 15 Using the Foot Pedal to Change the Pitch (GLIDE) ............................................................................ 15 Using the Foot Pedal to Sustain the Sound (HOLD)........................................................................... 16 Using the Expression Pedal to Modify the Sound (EXP PEDAL) ..................................................... 16 Turning the Power Off............................................................................................................................. 16 Chapter 2 Using the GR-20 with Guitar Effects..................................17 Connections ............................................................................................................................................... 17 Switching between the Synth Sound and Guitar Sound .................................................................... 18 Using the GR-20 with a Multi-effects Unit ........................................................................................... 18 Channel (CH)................................................................................................................................. 18 Patch Link Setup (PATCH LINK SETUP) ................................................................................. 19 Chapter 3 Editing The Sounds.............................................................20 Selecting a Sound to Start From ............................................................................................................. 20 Use the Knobs to Adjust the Sound ....................................................................................................... 20 Adjusting the Attack--ATTACK................................................................................................ 20 Adjusting the Release--RELEASE.............................................................................................. 20 Adjusting the Spaciousness of the Sound--CHORUS ............................................................ 20 Adjusting the Reverberation--DELAY/REVERB.................................................................... 20 Adjusting the Volume--LEVEL.................................................................................................. 20 6 Contents Editing Other Parameters........................................................................................................................ 21 Adjusting the Brightness of the Sound--FREQ........................................................................ 21 Adding a Distinctive Character to the Tone--RESO ............................................................... 21 Adjusting the Pitch --TRANSPOSE........................................................................................... 21 Adjusting the Playing Feel--PLAY FEEL.................................................................................. 21 Selecting the Type of Glide Effect--GLIDE TYPE............................................................................... 22 Selecting the Type of Hold Effect--HOLD TYPE................................................................................ 23 Selecting the Effect Controlled by the Expression Pedal--EXP PEDAL.......................................... 23 Storing the Sounds You Create (WRITE) .............................................................................................. 24 Chapter 4 Other Functions...................................................................25 Copying Patches ....................................................................................................................................... 25 Exchanging Patches.................................................................................................................................. 25 Changing the function of the foot pedals (SW MODE) ...................................................................... 26 Switch Mode 1 ............................................................................................................................... 26 Switch Mode 2 ............................................................................................................................... 26 Saving Patches and System Parameter Settings on an External Device (BULK DUMP) ............... 26 Loading Patches and System Parameter Settings From an External Device (BULK LOAD)................ 27 Chapter 5 Connecting an External Sound Module or Sequencer..............28 Connecting an External Sound Module or Sequencer ........................................................................ 28 Setting the Transmission Mode................................................................................................... 28 Setting the MIDI Channel (BASIC CHANNEL) ....................................................................... 29 Specifying the Bend Range .......................................................................................................... 29 MIDI Messages Transmitted by the GR-20 ............................................................................... 29 Local Control Off ...................................................................................................................................... 30 Chapter 6 Appendices ..........................................................................31 Restoring the Factory Settings (Factory Reset)..................................................................................... 31 Calibrating the Expression Pedal ........................................................................................................... 31 Regarding GR-20 bass guitar support ................................................................................................... 32 Switching the GR-20 between bass guitar and guitar operation............................................ 32 How the Bass Guitar and Guitar settings differ ....................................................................... 32 Troubleshooting........................................................................................................................................ 33 During Normal Performance Using the GR-20 Alone............................................................. 33 When Using the GR-20 with other MIDI devices..................................................................... 33 Other ............................................................................................................................................... 34 Patch List.................................................................................................................................................... 35 User Patch List .......................................................................................................................................... 40 MIDI Implementation .............................................................................................................................. 41 MIDI Implementation Chart ................................................................................................................... 48 Main Specifications .................................................................................................................................. 49 INDEX ........................................................................................................................................................ 50 7 Names of Things and What They Do Front Panel fig.0-01 (Panel Descriptions1) 1. BANK indicators These indicators light to indicate the currently selected sound bank. If the bank has been switched from an external device (such as via MIDI or by the switches of your GK pickup), the indicator for the selected bank will light regardless of the position of the BANK knob. 5. GK SIGNAL indicator This indicator lights when a signal is received from the divided pickup. 6. [GK SENS] button Press this button when you want to adjust the sensitivity to match the output of the divided pickup. The system may malfunction if this adjustment is not made correctly. Please adjust this setting accurately to match your guitar (p. 12). 2. [BANK] knob Selects the sound bank. The banks are organized into ten categories of sound. Sounds you edit can be stored in the User bank (p. 24). 3. Display Indicates the currently selected sound number. When you're editing a parameter, the display indicates the value. If you've edited the sound, the dot will light (p. 20). 7. OUTPUT/FREQ indicator This indicator lights when you edit the System parameter OUTPUT Select or the Patch parameter FREQ (p. 14, p. 21). 8. SW MODE/RESO indicator This indicator lights when you edit the System parameter SW MODE or the Patch parameter RESO (p. 14, p. 21). 4. [NUMBER/VALUE] knob Use this to select the number of the sound you want to play. Use the [BANK] knob (2) to select a category of sounds, and use this knob to select a sound within that category. This knob is also used to change the values of other parameters. 8 Names of Things and What They Do 9. PATCH LINK SETUP/TRANSPOSE indicator This indicator lights when you edit the System parameter PATCH LINK SETUP or the Patch parameter TRANSPOSE (p. 19, p. 21). 21. [EXP PEDAL] button Press this button to select the function of the expression pedal (p. 23). 22. [GLIDE TYPE] button Press this button to select the function of the Glide pedal (p. 22). 10. MIDI CH/PLAY FEEL indicator This indicator lights when you edit the System parameter MIDI CH or the Patch parameter PLAY FEEL (p. 18, p. 21). 23. [HOLD TYPE] button Press this button to select the function of the Hold pedal (p. 23). 11. [SYSTEM EDIT] button Press this when you want to edit System parameters (p. 14, p. 18, p. 19, p. 26, p. 27). 24. GLIDE pedal Press this pedal to apply the Glide effect to the sound (p. 15). 12. [PATCH EDIT] button Press this when you want to edit Patch parameters (p. 21). 25. GLIDE indicator This indicator will light or blink according to how you operate the GLIDE pedal. 13. [ATTACK] knob Adjusts the speed of the attack (p. 20). 26. HOLD pedal Press this pedal to apply the Hold effect to the sound (p. 16). 14. [RELEASE] knob Adjusts the length of the release (p. 20). 27. HOLD indicator 15. [CHORUS] knob Adjusts the chorus depth (p. 20). This indicator will light or blink according to how you operate the HOLD pedal. 16. [DELAY/REVERB] knob Adjusts the delay or reverb depth (p. 20). 28. Expression pedal Use this pedal to adjust the volume or to apply continuous change to the sound (p. 16). 17. [LEVEL] knob Adjusts the volume of the synth sound for each patch (p. 20). When you operate the expression pedal, please be careful not to get your fingers pinched between the movable part and the panel. 18. [EXIT] button Press this to cancel an operation, or to return to a previous state. 19. [WRITE] button Press this button to write (store) or copy a patch (p. 24, p. 25). In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit. 20. [TUNER] button Press this button when you want to use the Tuner function (p. 13). 9 Names of Things and What They Do Rear Panel fig.0-02 (Panel Descriptions2) 29. GK IN connector Use the included GK cable (or GKC-3/5/10 (sold separately) to connect this connector to your divided pickup. * For details on connections to a commercially available GKcompatible guitar, refer to the guitar manufacturer or your dealer. * This is available only if the output of your guitar is connected to the normal pickup input jack of the divided pickup. 33. [OUTPUT LEVEL] knob Adjusts the volume that is sent from the output jacks. 34. MIDI IN/OUT connectors These can be connected to external MIDI devices, allowing the GR-20 to send and receive MIDI data. 30. GUITAR OUT jack This jack outputs the sound from the normal pickup of your guitar. Connect this jack to your guitar amp or guitar effects unit. 35. [POWER] switch Turns the power on/off. 31. MIX IN R (MONO)/L jacks The sound that is input to these jacks is mixed with the synth sound of the GR-20 and sent from the OUTPUT jacks (32). If you have connected the GUITAR OUT jack (30) to an external effects unit, connect the output of your effects unit to this jack; the synth sound and the sound processed by the effects unit will be output together from the OUTPUT jacks (32) (p. 17). 36. AC Adaptor jack Connect the included AC adaptor (BRC-series) here. Use only the attached power-supply cord. Also, the supplied power cord must not be used with any other device. 37. Cable hook 32. OUTPUT R (MONO)/L (PHONES) jacks These jacks output the GR-20's synth sound combined with the sound that is input to the MIX IN jacks (31). If you're making connections to a monaural amp, use R (MONO) jack. The L (PHONES) jack can also be used as a headphone jack (stereo). (However, if headphones are connected to L (PHONES) jack, you cannot simultaneously use R (MONO) jack as an output.) If nothing is connected to the GUITAR OUT jack (30) or MIX IN jacks (31), the guitar's normal pickup sound will also be mixed into this output. Loop the AC adaptor cable around this hook to prevent the cable from being accidentally disconnected. 38. Security Slot ( ) http://www.kensington.com/ 10 Chapter 1 Play the Sounds! Preparing Your Guitar · In order to use the GR-20 you will need a guitar that has a divided pickup (GK pickup) such as the Roland GK-3 or GK-2A, or a bass guitar that has a bass guitar divided pickup such as the Roland GK-3B/GK-2B, which can independently output a separate signal for each string. · For details on installing the GK pickup, refer to the manual that came with your GK pickup. · Notes may be sounded incorrectly if there are string buzzes due to improper neck curvature or buzzing frets, or if the octave adjustment (intonation) is incorrect. Various guitar manufacturers sell GK-Compatible guitars that have a pre-installed GK pickup or contain equivalent functionality. For details, contact your guitar dealer or a guitar manufacturer. In order to use the GR-20 with a bass guitar, follow the procedure described in Chapter 6 Appendices "Switching the GR-20 between bass guitar and guitar operation (p. 32)" to switch the GR-20 to bass guitar operation. Connections fig.1-01(Connection) Stereo set, radio-cassette player, etc. Synthesizer amp (keyboard amplifier, PA system, etc.) To AUX, LINE IN L R L R Guitar amp / guitar effects processors Stereo headphones The (L) MIX OUT jacks can also be used as dual stereo headphone jacks. Also be aware that you cannot simultaneously use one jack as a LINE OUT while using the other as a headphone jack ­ that is, you can't use a monaural plug and a stereo plug at the same time. Guitar with GK-3 / GK-2A / other GK-Compatible guitar or Bass guitar with GK-3B / GK-2B AC adaptor (BRC series) * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections * The volume of your amp should be raised only after you have turned on the power of all your other equipment. * If you're outputting in monaural, connect the cable to the R (MONO) OUTPUT jack. * To prevent the inadvertent disruption of power to your unit (should the plug be pulled out accidentally), and to avoid applying undue stress to the AC adaptor jack, anchor the power cord using the cord hook, as shown in the illustration. fig.1-02(Cord Hook) 11 Chapter 1 Play the Sounds! Turning the Power On Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 1. If you've connected a device to MIX IN, turn on the power of that device. 2. Turn on the power of the GR-20. Adjusting the Input Sensitivity (GK SENS) You'll need to adjust the input sensitivity of each string according to your picking strength and how the divided pickup is installed. If this adjustment is not made correctly, the system won't work properly. You must perform this adjustment to ensure that you're taking full advantage of the GR-20's capabilities. * Once you make this adjustment, it's stored within the GR-20; you won't need to make it again. However, you should perform the adjustment again after changing the strings or adjusting the action of your guitar, or before using a different GK guitar. * If you're using a bass guitar, you can use the following table to convert the string names and indications you see in the display while performing the procedure below. 6th string B string 5th string E string (4th string on a conventional four-string bass) 4th string A string (3rd string on a conventional four-string bass) 3rd string D string (2nd string on a conventional four-string bass) 2nd string G string (1st string on a conventional four-string bass) 1st string C string 1. Press the [GK SENS] button. 2. Play only the 6th string. The left side of the display will show "6," indicating that you played the 6th string. The right digit will show the GK SENS setting. The BANK indicators will function as a level meter and show the strength of the guitar signal. After you've turned on the power, you'll be ready to play when the panel indicators and the display reach the state shown in the illustration. This state is called "Play mode." Before the GR-20 enters Play mode, it will indicate whether it is currently in guitar mode or bass guitar mode. · Guitar mode: " · Bass guitar mode: " " " * For details on how to switch between guitar mode and bass guitar mode, refer to p. 32. * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. fig.1-03(Play Mode) 3. Turn on the power of your amp. * If the left digit of the display does not show the number of the string you played, press the HOLD pedal or GLIDE pedal several times to make the desired string number appear. fig.1-04(GK SENS) Adjusting the Output Level Use the [OUTPUT LEVEL] knob on the rear panel to adjust the output level of the GR-20. Turning the knob toward the right (toward MAX) will increase the volume. With the knob turned all the way to the left (toward MIN), the volume will be zero. * Normally, you should set this near the middle of the range. fig.1-10(Level) Level Meter 3. Adjust the sensitivity. Turn the [NUMBER/VALUE] knob to adjust the sensitivity. The sensitivity will increase as the number in the right of the display increases. Adjust the sensitivity so that all of the level meter indicators light briefly when you pick a note strongly. 12 Chapter 1 Play the Sounds! * You can also use your GK pickup's UP/S2 button and DOWN/S1 button to adjust the sensitivity in the same way. 4. Perform steps 2­3 for strings 5­1 to adjust the sensitivity of all strings. 5. Press the [GK SENS] button or [EXIT] button. The GK SENS settings you made are stored in the GR20k, and you will return to Play mode. * The decimal point in the display will blink while the setting is being stored. Don't turn off the power during this time. * If you turn off the power before returning to Play mode, the settings you made will not be stored. 2. Use the [NUMBER/VALUE] knob to adjust the reference pitch. If you turn the [NUMBER/VALUE] knob slightly, the current reference pitch will be displayed for several seconds. By turning the [NUMBER/VALUE] knob during this time, you can adjust the reference pitch. * You can adjust the reference pitch in a range of 427 Hz­452 Hz. When the GR-20 is shipped from the factory, this is set to 440 Hz. * The reference pitch you specify will be stored when you exit the Tuner function. Be aware that the setting will not be stored if you turn off the power before doing so. 3. Cleanly play an unfretted note on the string that you want to tune. If you're using a bass guitar, the number shown at the left side of the display will be as shown in the following table. The display will indicate the note name. fig.1-051 Displayed No. 1 4-string bass 5-string bass 6-string bass 2 1G string 1G string 3 2D string 2D string 3D string 4 5 6 C C# F# G G# A A# B 3A 4E string string 3A 4E string string 4A 5E string string 5B string 6B string D D# E F 1C 2G string string Tuning Your Guitar (Tuner Function) Since the GR-20 analyzes the pitch of each string in order to determine the sound it should produce, you must tune your guitar accurately. * If your guitar is mistuned, the sound produced will be out of tune, and the system will not operate correctly. 1. Press the [TUNER] button. The [TUNER] button will light, and the Tuner function will be on. The lower two digits of the current reference pitch will be shown for approximately two seconds in the display. Then you will be able to tune your guitar. Example: When the pitch is set to 440Hz fig.1-05(Reference pitch) 4. Tune your guitar. Watch the indicator in the panel, and tune your guitar so that only the green indicator in the middle is lit. fig.1-06(Tuning) too low too high 5. Repeat steps 3­4 to tune each string of your guitar. 6. Press the [TUNER] or [EXIT] button to exit the Tuner function. The reference pitch you specified will be stored, and you will return to Play mode. * The decimal point in the display will blink while the reference pitch is being stored. Don't turn off the power during this time. * You can also turn on the Tuner function by pressing the HOLD pedal and GLIDE pedal simultaneously. 13 Chapter 1 Play the Sounds! Specifying the Output Device (OUTPUT SELECT) Here you can specify the type of system connected to the OUTPUT jacks. This setting allows the GR-20 to internally optimize its sound for the type of playback system you are using. * This does not affect the sound that is input to MIX IN. 1. Press the [SYSTEM EDIT] button a number of times until the OUTPUT/FREQ indicator lights. fig.1-07(OUTPUT SELECT) Selecting a Sound (Patch) What is a Patch A "patch" is a sound you play on the GR-20; in addition to the type of sound, a patch also contains settings for effects such as reverb and chorus. The GR-20's patches are organized into ten banks by type, with the patches numbered within each bank. In Play mode, the BANK indicator and the display show the patch that is currently selected. You can edit the settings of a patch to your taste, and store edited patches in the USER bank (p. 24). You can use any of the following ways to select a patch. Using the Knob to Select Patches 1. Use the [BANK] knob to select the type of sound you want. 2. Use the [NUMBER/VALUE] knob to change the setting. Guitar amp fig.1-071 From the ten sound banks and the user bank, select the bank that contains the sound you want to use. 2. Use the [NUMBER/VALUE] knob to select a sound within the bank. Turning the [NUMBER/VALUE] knob will change the number shown in the display, letting you choose from various sounds within the selected bank. fig.1-08(Sound Select) Use this setting if you've connected the GR-20 to a guitar amp. Line fig.1-072 Use this setting if you've connected the GR-20 to a keyboard amp, mixer, headphones, or recorder. * If you're using a bass amp, use the Line setting. 3. Press the [EXIT] button. The setting will be stored, and you will return to Play mode. * The decimal point in the display will blink while the setting is being stored. Don't turn off the power during this time. * If you turn off the power before returning to Play mode, the setting you made will not be stored. 14 Chapter 1 Play the Sounds! Using the Switches of the GK Pickup to Select Patches In Play mode, you can use the UP/S2 button and DOWN/S1 button of the GK pickup to select the next or previous number. When you reach the upper or lower limit within a bank, you will move to the next bank. fig.1-09(S1/S2) Play the GR-20! Let's get started playing the GR-20. Check the following points. 1. Make sure that the GR-20 is in Play mode (the state it's normally in immediately following power up). In some cases, you won't hear any sound if the GR-20 is not in Play mode. 2. Set the select switch of your GK pickup to the "GK" position (on the GK-2A, the "SYNTH" position). If this switch is set to "GUITAR," the normal pickup sound will be output. If this switch is set to "MIX," the synth sound and the guitar normal pickup sound will be mixed and output. 3. Turn the volume of the GK pickup to the right. Using the Foot Pedals to Select Patches When shipped from the factory, the GR-20's two foot pedals are assigned to the Hold function and Glide (Pitch Bend) function respectively. You can change these assignments so that the foot pedals will select patches. For details, refer to Changing the function of the foot pedals (SW MODE) (p. 26). This volume controls the synth sounds of the GR-20. fig.1-11(GK-3) Using an External Device Via MIDI to Select Patches You can connect an external device (e.g., multi-effects unit) to the MIDI IN connector, and select patches on the GR-20 by operating the external MIDI device. For details, refer to Using the GR-20 with a Multi-effects Unit (p. 18). Using the Foot Pedal to Change the Pitch (GLIDE) You can press the GLIDE pedal to change the pitch of the currently playing synth sound smoothly. The type of change will depend on the sound, and you can also adjust the change to your taste (p. 22). fig.1-12(GLIDE) * The GLIDE indicator will blink while you are pressing the pedal. 15 Chapter 1 Play the Sounds! Using the Foot Pedal to Sustain the Sound (HOLD) You can press the HOLD pedal to sustain the synth sound you're playing. The effect will depend on the sound, and you can also adjust the effect to your taste (p. 23). fig.1-13(HOLD) Turning the Power Off When you're ready to turn off the power, be sure to do so in the following order. 1. Turn off the power of your amp. 2. Turn off the power of the GR-20. 3. Turn off the power of the device connected to MIX IN. * The HOLD indicator will blink while you are pressing the pedal. Using the Expression Pedal to Modify the Sound (EXP PEDAL) You can use the expression pedal to continuously vary the volume or tone of the synth sound. The effect will depend on the sound, and you can also adjust the effect to your taste (p. 23). fig.1-14(EXP) 16 Chapter 2 Using the GR-20 with Guitar Effects Here's how you can use your own effects unit and combine the sound of the guitar with the synth sound to create an even more interesting range of possibilities. The sound of the guitar's normal pickups will pass through the GK cable and be output from the GR-20's GUITAR OUT jack. The sound that is processed by your effects unit can be connected to the GR-20's MIX IN, and internally mixed with the GR-20's synth sound. * Connect the output of your guitar to the normal pickup input jack of the GK pickup. Connections Using a compact effect device or a multi-effects unit that has no MIDI connector fig.2-01(Effect Connection 1) Guitar amp * Set the GR-20's OUTPUT SELECT to "Guitar Amp" (p. 14). Using a multi-effects unit that has a MIDI connector fig.2-02(Effect Connection 2) Keyboard amplifier, PA system, etc. * If you're using a multi-effects unit, set the GR-20 as follows: Guitar Amp Simulation: on Output Select: line * Set the GR-20's OUTPUT SELECT to "Line" (p. 14). * If your multi-effects device does not have a amp simulator, set the GR-20's OUTPUT SELECT to "Guitar Amp," and connect the output to a guitar amp. 17 Chapter 2 Using the GR-20 with Guitar Effects Switching between the Synth Sound and Guitar Sound To switch between the synth sound and guitar sound, use the selector switch provided on your GK pickup. f Using the GR-20 with a Multi-effects Unit By connecting your multi-effects unit via MIDI, you can automatically change sounds (patches) on the GR-20 by selecting sounds (patches) on your multi-effects unit. Channel (CH) MIDI uses "channels" to send independent streams of data over a single cable. In order for data to be received, the receiving device must be set to receive the channel that the transmitting device is sending on. This means you must set the transmit channel of your multi-effects unit to match the receive channel of the GR-20. 1. Check the MIDI transmit channel of your multi-effects unit. For details, refer to the manual of your multi-effects unit. 2. Press the [SYSTEM EDIT] button a number of times until the MIDI CH/PLAY FEEL indicator lights. fig.2-03(MIDI CH) If the selector of your GK pickup (e.g., GK-3, GK-2A) is set to the GK position (labeled SYNTH on the GK-2A), the synth sound will be output. If set to the GUITAR position, the guitar sound will be output. If the selector is set to MIX, both sounds will be mixed and output. * To adjust the volume balance between the synth sound and guitar sound, use the volume (p. 20) of each patch to adjust the synth sound, and the volume of the guitar or the connected effects device to adjust the volume of the guitar sound. 3. Use the [NUMBER/VALUE] knob to change the setting. Set the channel so it's the same as the MIDI transmit channel of your multi-effects unit. 4. Press the [EXIT] button. The setting will be stored, and you will return to Play mode. * The decimal point in the display will blink while the setting is being stored. Don't turn off the power during this time. * If you turn off the power before returning to Play mode, the setting you made will not be stored. 18 Chapter 2 Using the GR-20 with Guitar Effects Patch Link Setup (PATCH LINK SETUP) Here's how to link the patches (sounds) of your multi-effects unit with the patches (sounds) of the GR-20. This will cause the GR-20 to automatically switch to the specified sound (patch) when you change patches on your multi-effects unit. 1. Use a MIDI cable to connect the MIDI OUT of your multi-effects unit to the GR-20's MIDI IN. 2. Make sure that the MIDI transmit channel of your multieffects unit is the same as the MIDI channel of the GR-20 (p. 18). 3. Press the [SYSTEM EDIT] button a number of times until the PATCH LINK SETUP/TRANSPOSE indicator lights. fig.2-04(PATCH LINK) 4. On your multi-effects unit, select the patch for which you want to specify a link. * When you select a patch on your multi-effects unit, it will send a "MIDI Program Change" message to the GR-20. The GR-20 will remember the content of this message, and will be ready for you to specify the patch link setting. * If two or more consecutive patch changes occur when you are selecting a patch on your multi-effects unit, the GR-20 will remember only the last-received MIDI program change. 5. Use the [BANK] knob and [NUMBER/VALUE] knob to select the synth sound in the GR-20 that you want to use with the effect you chose in step 4. 6. Repeat steps 4­5 to set as many links as you need. 7. Press the [EXIT] button. You will return to Play mode, and the settings you made will be stored. * The decimal point in the display will blink while the setting is being stored. Don't turn off the power during this time. * If you turn off the power before returning to Play mode, your settings will not be stored. 19 Chapter 3 Editing The Sounds The GR-20 lets you modify the sound to your taste. This process is called "editing." When you edit the settings, the decimal point in the display will light, indicating that the sound has been modified from the original settings. With the knob turned all the way to the left, it activates the envelope follower function. Envelope Follower (E FLW) function The guitar synth analyzes the vibration of your guitar string to detect the pitch, and then plays the appropriate synth sound. This means that if the string vibration is less than a certain level, it will not be possible to detect the pitch, and the synth sound will be silenced at that point. For some patches, the way in which the sound is silenced at this time may produce an unnatural result. The envelope follower function causes the volume of the synth sound to always follow the string vibration of the guitar, making the synth sound decay naturally along with the decay of the string vibration. * For some patches, the effect may be slight. * Using the envelope follower function on a decay-type synth sound such as piano or guitar may have the opposite effect, producing an unnatural-sounding decay. Selecting a Sound to Start From Use the [BANK] knob and [NUMBER/VALUE] knob to select the sound (patch) from which you want to start editing (p. 14). Use the Knobs to Adjust the Sound fig.3-01(knob) Adjusting the Spaciousness of the Sound--CHORUS This adjusts the depth of the chorus effect, which gives the sound a spacious feel. Turning the knob toward the right will deepen the effect, and turning it toward the left will lessen the effect. * You will hear the original sound when the knob is at the center position. * For some sounds, moving the knob may not make any difference. * Immediately after a patch change, the sound you'll hear will reflect the settings stored in the patch, regardless of the positions of the knobs. Adjusting the Attack--ATTACK This adjusts the attack time of the sound. Turning the knob toward the right will lengthen the time, producing a more gradual attack. Turning the knob toward the left will shorten the time, producing a sharper attack. * You will hear the original sound when the knob is at the center position. * For some sounds, moving the knob may not make any difference. Adjusting the Reverberation --DELAY/REVERB This controls two types of reverberation effect. Delay is an effect that produces echo-like effects, while Reverb is an effect that simulates the way in which sound reflects from the walls of a hall or tunnel. The left half of the knob's range applies a delay effect, and the right half applies reverb. In either case, turning the knob farther will deepen the effect. Adjusting the Release--RELEASE This adjusts the release, from when you mute a string until it decays to silence. Turning the knob toward the right will lengthen the release, and turning it toward the left will shorten the release. * You will hear the original sound when the knob is at the center position. * For some sounds, moving the knob may not make any difference. Adjusting the Volume--LEVEL This adjusts the volume of the patch. * If you want to keep your edited sound, execute Write (p. 24) to write your settings into a USER patch. 20 Chapter 3 Editing The Sounds Editing Other Parameters You will use the [PATCH EDIT] button and [NUMBER/ VALUE] knob to edit these parameters. 1. Press the [PATCH EDIT] button a number of times until the indicator of the parameter you want to edit is lit. 2. Use the [NUMBER/VALUE] knob to edit the value. fig.3-02(Other Parameters) Adjusting the Playing Feel --PLAY FEEL You can select the way in which the synth sound will respond to your picking dynamics. You can more naturally express your playing dynamics by changing this setting to suit a particular playing style or sound. 1­4: The "1" setting gives you the widest range of volume change in response to your picking dynamics. With higher-numbered settings, even softly picked notes will sound at a high volume, making the volume more consistent even when you use tapping techniques or if your picking is not consistent. No dynamics: With this setting, notes will be sounded at a fixed volume regardless of your picking dynamics. Adjusting the Brightness of the Sound--FREQ This controls the cutoff frequency of the filter within the sound generator. Increasing this setting will raise the frequency, producing a brighter tone. Conversely, decreasing this setting will lower the frequency, producing a softer tone. Strum: This setting suppresses softly picked notes. Use this setting if unwanted notes are triggered when you strum or when your finger contacts a string unintentionally. 3. Press the [EXIT] button to return to Play mode. * If you want to keep your edited sound, execute Write (p. 24) to write your settings into a USER patch. Adding a Distinctive Character to the Tone--RESO This controls the resonance of the filter within the sound generator. Increasing this setting will produce a more distinctive tone, while decreasing the setting will produce a milder tone. Adjusting the Pitch --TRANSPOSE The pitch of the synth sound produced by the GR-20 can be raised or lowered in one-octave steps relative to the pitch you play on your guitar. (-2, -1, 0, +1, +2) 21 Chapter 3 Editing The Sounds Selecting the Type of Glide Effect--GLIDE TYPE You can select how the pitch changes when you press the GLIDE pedal. 1. Press the [GLIDE TYPE] button. fig.3-03(GLIDE TYPE) u5­u8: GLIDE UP 5­8 d5­d8: GLIDE DOWN 5­8 The pitch will change one octave (up/ down) when you press the GLIDE pedal, and will return to normal when you release the pedal. Higher settings will shorten the time over which the pitch changes. V1­V4: VIBRATO 1­4 Pressing the pedal applies vibrato (an effect that changes the pitch cyclically). The effect quickens as the value is increased 2. Use the [NUMBER/VALUE] knob to change the setting. u1: GLIDE UP 1 d1: GLIDE DOWN 1 The pitch will change one semitone (up/ down) when you press the GLIDE pedal, and will return to normal when you release the pedal. 3. Press the [GLIDE TYPE] button or [EXIT] button to return to Play mode. * If you want to keep your edited sound, execute Write (p. 24) to write your settings into a USER patch. u2: GLIDE UP 2 d2: GLIDE DOWN 2 The pitch will change a whole step (up/ down) when you press the GLIDE pedal, and will return to normal when you release the pedal. u3: GLIDE UP 3 d3: GLIDE DOWN 3 The pitch will change a perfect fourth (up/down) when you press the GLIDE pedal, and will return to normal when you release the pedal. u4: GLIDE UP 4 d4: GLIDE DOWN 4 The pitch will change a perfect fifth (up/ down) when you press the GLIDE pedal, and will return to normal when you release the pedal. 22 Chapter 3 Editing The Sounds Selecting the Type of Hold Effect--HOLD TYPE You can select the type of hold effect you'll get when you press the HOLD pedal. 1. Press the [HOLD TYPE] button. fig.3-04(HOLD TYPE) 3. Press the [HOLD TYPE] button or [EXIT] button to return to Play mode. * If you want to keep your edited sound, execute Write (p. 24) to write your settings into a USER patch. Selecting the Effect Controlled by the Expression Pedal--EXP PEDAL You can select one of the following as the effect controlled by the expression pedal. 1. Press the [EXP TYPE] button. fig.3-05(EXP TYPE) 2. Use the [NUMBER/VALUE] knob to change the setting. H1: HOLD 1 The notes that were sounding when you pressed the pedal will be held, and any notes you play while continuing to press the pedal will also be held. However, if you play any notes on a string that was already sounding, the previous note will disappear and be replaced by the newly played note. This lets you smoothly play notes located at different fret positions. H2: HOLD 2 The notes that were sounding when you pressed the pedal will be held as long as you continue pressing the pedal. Subsequent notes that you play while holding the pedal will not be heard. This lets you hold a chord using the synth sound, and play a melody using the guitar sound. H3: HOLD 3 The notes that were sounding when you pressed the pedal will be held as long as you continue pressing the pedal. Subsequent notes that you play while holding the pedal will sound but will not be held. (The notes that you can play afterward are limited to strings other than those that are being held.) This lets you hold a chord using the synth sound on the low notes, and play a melody on the high notes. H4: HOLD 4 The notes that were sounding when you pressed the pedal will be held, and any subsequent notes you play while continuing to press the pedal will also be held. This is the same behavior as the damper pedal of a piano. 2. Use the [NUMBER/VALUE] knob to change the setting. VO: VOLUME The pedal will adjust the overall volume of the synth sound. FL: FILTER The pedal will adjust the filter cutoff frequency of the sound generator, varying the tone. b1: PITCH BEND 1 When the pedal is pressed, the pitch changes up to a perfect fourth (max.). b2: PITCH BEND 2 When the pedal is pressed, the pitch changes up to a perfect fifth (max.). b3: PITCH BEND 3 When the pedal is pressed, the pitch changes up to one octave (max.). 23 Chapter 3 Editing The Sounds b4: PITCH BEND 4 When the pedal is pressed, the pitch changes down to a semi tone (max.). Storing the Sounds You Create (WRITE) The sounds you create will be lost if you change the patch or simply turn off the power. If you want to keep the modifications you've made, you must perform the Write procedure. 1. Press the [WRITE] button. b5: PITCH BEND 5 When the pedal is pressed, the pitch changes down to a whole tone (max.). b6: PITCH BEND 6 When the pedal is pressed, the pitch changes down to one octave (max.). fig.3-06(WRITE) EF: Effect The pedal will adjust the effect used within each patch. * The result will differ for each patch. * For some patches, there will be no effect. 3. Press the [EXP TYPE] button or [EXIT] button to return to Play mode. * If you want to keep your edited sound, execute Write (p. 24) to write your settings into a USER patch. The BANK indicators will indicate USER, and the display will blink. 2. Use the [NUMBER/VALUE] knob to select the patch number into which you want to write your settings. * If you decide to abort the Write operation at this point, press the [EXIT] button. 3. Press the [WRITE] button once again. Your settings will be written into the patch you selected. * Use caution, since the settings previously stored in that patch will be overwritten and lost. * The decimal point in the display will blink while the setting is being stored. Don't turn off the power during this time. 24 Chapter 4 Other Functions Copying Patches Here's how you can copy patch settings. You can copy only to the USER bank. 1. Select the copy-source patch (the patch you want to copy from). 2. Press the [WRITE] button. The BANK indicator will change to USER, and the display will blink. fig.4-01(COPY) Exchanging Patches Here's how you can exchange (swap) patches within the USER bank. This is a convenient way to arrange USER bank patches in the desired order. * This will not work if the selected patch is not in the USER bank. 1. Select one of the patches that you want to exchange. 2. Hold down the [EXIT] button and press the [WRITE] button. The indication in the display starts blinking. fig.4-02(EXCNG) 3. Use the [NUMBER/VALUE] knob to select the copydestination patch number (patch number you want to copy to). 4. Press the [WRITE] button once again. The setting will be copied to the copy-destination patch. * The decimal point in the display will blink while copying the setting. * Use caution, since the settings previously stored in the copydestination patch will be overwritten and lost. 3. Use the [NUMBER/VALUE] knob to select the other patch that you want to exchange. 4. Press the [WRITE] button once again. The patches will be exchanged. * The decimal point in the display will blink while the patches is being exchanged. 25 Chapter 4 Other Functions Changing the function of the foot pedals (SW MODE) You can change the function of the GLIDE pedal and the HOLD pedal by changing the switch mode. This setting also changes the function of your GK pickup's DOWN/S1 screen and UP/S2 switch. 2. Use the NUMBER/VALUE knob to change the setting. * The actual mode of operation will not change until you store the setting and return to Play mode. 3. Press the [EXIT] button. You will return to Play mode, and the setting will be stored. * The decimal point in the display will blink while the setting is being stored. Don't turn off the power during this time. * The setting will not be stored if you turn off the power without returning to Play mode. * In Switch Mode 1, the GLIDE indicator and HOLD indicator will normally be lit; they will blink only while you press the pedal. * In Switch Mode 2, the GLIDE indicator and HOLD indicator will normally be unlit; however, when the function of each pedal is being changed by pressing the DOWN/S1 switch or UP/S2 switch, the indicators will behave the same way as they do in Switch Mode 1. Switch Mode 1 The GLIDE pedal operates the Glide function, and the HOLD pedal operates the Hold function. Your GK pickup's UP/S2 switch and DOWN/S1 switch will move up/down through the patches. * This mode is selected when the GR-20 is shipped from the factory. Switch Mode 2 The HOLD pedal and GLIDE pedal will move up/down through the patches. You can use your GK pickup's DOWN/S1 switch and UP/S1 switch in conjunction with the pedals to perform the following operations. · When you press the DOWN/S1 switch, the GLIDE pedal will function as Octave Down and the HOLD pedal will function as Octave Up (TRANSPOSE). When you press DOWN/S1 (or UP/S2) once again, the pedals will revert to the patch up/down function. · When you press the UP/S2 switch, the GLIDE pedal will function as Glide and the HOLD pedal will function as Hold. When you press UP/S2 (or DOWN/S1) once again, the pedals will revert to the patch up/down function. 1. Press the [SYSTEM EDIT] button enough times to get the SW MODE indicator to light. Saving Patches and System Parameter Settings on an External Device (BULK DUMP) Here's how you can save the user bank patches and the system parameter settings via MIDI on an external device or computer (sequencer). You can also transfer data via a MIDI cable directly between two GR-20 units. Sending GR-20 data in this way is called "bulk dump," and receiving this data is called "bulk load." What are System Parameters? Parameters that apply to the entire GR-20 (such as SW MODE and MIDI CH) are called "system parameters." 1. Connect the GR-20's MIDI OUT to your external device's MIDI IN. 26 Chapter 4 Other Functions 2. Turn off the power of the GR-20, and then hold down the [PATCH EDIT] button while you turn the power on again. The display will indicate "dP." fig.4-03(DUMP) Loading Patches and System Parameter Settings From an External Device (BULK LOAD) Here's how GR-20 settings saved via Bulk Dump on an external device can be loaded back into the GR-20 via MIDI. Performing the BULK LOAD operation will rewrite all the data in the GR-20. Be aware that all currently existing data will be lost. 1. Connect your external device's MIDI OUT to the GR-20's MIDI IN. 3. Begin recording on the external device that will receive the data. If you want to transfer data between two GR-20 units, put the receiving GR-20 in the Bulk Load (p. 27) Ready state. 4. Press the [WRITE] button. The data will be transmitted from MIDI OUT to the external device. During transmission, the display will show the following. fig.4-031 2. Turn off the power of the GR-20, and then hold down the [PATCH EDIT] button and turn the power back on again. The display will indicate "dP." 3. Using the [NUMBER/VALUE] knob, get "Ld" to appear in the display. fig.4-04(LOAD) Lit When the display returns to "dP," transmission has been completed. 5. Stop recording on the receiving device. 6. Turn off the power. 4. Transmit the data from your external device. During transmission, the display will show the following, and the decimal point of the display will blink. fig.4-041 When the decimal point of the display stops blinking, and the display again shows "Ld," reception has been completed. 5. Press the [WRITE] button. * If the power of the GR-20 was turned off while the data was being received, the transmitted data will not be written into the GR-20. If necessary, perform the Bulk Load operation once again. 6. Press the [EXIT] button to return to Play mode. 27 Chapter 5 Connecting an External Sound Module or Sequencer You can use the GR-20 to play an external sound module via MIDI, or use it as an input tool for your sequencer. Setting the Transmission Mode The GR-20 lets you select either "Mono Mode transmission" or "Poly Mode transmission" as the method it uses when transmitting MIDI messages. Connecting an External Sound Module or Sequencer Connect the GR-20 to your external sound module or computer (sequencer) as shown in the diagram. fig.5-01(External Sound Module) Mono Mode transmission Performance data for each string will be transmitted individually, with each using its own separate MIDI channel. Starting with the selected MIDI CH, six consecutive MIDI channels will be selected automatically. For example, if MIDI CH is set to 3, the six channels 3­8 will transmit MIDI data for strings 1­6, respectively. Since continuous pitch change data (MIDI Pitch Bend messages) can be transmitted independently for each string, this allows you to use performance techniques typical of a guitar, such as use of the whammy bar and string bending. MIDI IN MIDI IN * The connected sound module must be a multitimbral sound module with at least six parts. MIDI OUT Poly Mode transmission Performance data for all strings will be transmitted on a single MIDI channel. The selected MIDI CH will be used. Since the entire guitar will use only one channel, this lets you conserve MIDI channels. This also lets you control a sound module that is not able to receive six channels simultaneously. * However, if two or more strings are sounding, bend data will not be transmitted; pitch change will occur only in semitone steps. This means that the pitch actually being played by the guitar will not be completely reflected by the synth sound. 1. Turn off the power of the GR-20, and hold down the [EXIT] button while you turn the power on again. MIDI Interface PC fig.5-03(Transmission Mode) fig.5-02(External Sequencer) MIDI IN MIDI OUT 2. Use the [NUMBER/VALUE] knob to select the mode. : MONO MODE * If you are connecting the GR-20 to a sequencer, turn "Local Control Off" (p. 30). : POLY MODE 28 Chapter 5 Connecting an External Sound Module or Sequencer 3. Press the [EXIT] button. The setting will be stored, and you will return to Play mode. * The decimal point in the display will blink while the setting is being stored. Don't turn off the power during this time. * If you turn off the power before returning to Play mode, the setting you made will not be stored. MIDI Messages Transmitted by the GR-20 As performance data, the GR-20 transmits a note-on message when you play a note, a note-off message when a note stops, and pitch bend messages when you bend a note. In addition to these messages, the GR-20 also transmits the following MIDI messages so that your performance can be faithfully reproduced when recorded and played back by a sequencer.