TD-12 MIDI Implementation Model: TD-12 Date: Dec. 17, 2004 Version: 1.00 Control Change Bank Select (Controller number 0, 32) Status BnH BnH 2nd byte 00H 20H 3rd byte mmH llH 0H - FH (ch.1 - ch.16) 00H - 7FH (bank.1 - bank.128) processed as 00H 1. Receive data Channel Voice Messages * * Following Channel Voice Messages can be received in [SETUP]-[MIDI]-[MIDI CH] Tx/Rx Channel. Not received when [SETUP]-[MIDI]-[MIDI CH] Rx/Rx Switch is set to "OFF. n = MIDI channel number: mm = Bank number MSB: ll = Bank number LSB: * * Note Off Status 8nH 9nH 2nd byte kkH kkH 3rd byte vvH 00H 0H - FH (ch.1 - ch.16) 00H - 7FH (0 - 127) 00H - 7FH (0 - 127) * Only the channels assigned to the backing part can be received. Refer to "Backing Instrument List" (p. 94) in the Owner's Manual. Bank select processing will be suspended until a program change message is received. Not recorded in the sequencer. Modulation (Controller number 1) n = MIDI channel number: kk = note number: vv = note off velocity: * * * Status BnH 2nd byte 01H 3rd byte vvH 0H - FH (ch.1 - ch.16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow Only the channels assigned to the backing part can be received. The Velocity Values of Note Off message are ignored. When recording, this is recorded in the sequencer data itself. n = MIDI channel number: vv = Control value: Note On Status 9nH 2nd byte kkH 3rd byte vvH 0H - FH (ch.1 - ch.16) 00H - 7FH (0 - 127) 01H - 7FH (1 - 127) * * * n = MIDI channel number: kk = note number: vv = note on velocity: * * * * A channel which is assigned to the drum part will receive only the note numbers which are specified by the drum kit. For more on note numbers, refer to "Preset Percussion Set List" (p. 92) in the Owner's Manual. When the [KIT]-[FUNC]-[BRUSH] Brush Switch is set to "ON", the note number set by means of [INST]-[CONTROL]-[BR MIDI] Brush Note No. is received on the channel assigned to the drum part (when an instrument campatible when bursh performances is selected for the Snare pad head). The note number set by means of [INST]-[CONTROL]-[BR MIDI] XStick Note No. is received on the channel assigned to the drum part (when an instrument compatible with cross-sticking is selected for the Snare pad rim). When recording, this is recorded in the sequencer data itself. * * Recieved only on channels not assigned to a percussion part. In the channel assigned to the drum part, setting [SETUP]-[MIDI]-[CTRL] Pedal CC to MODULATION changes the hi-hat control pedal position. In the channel assigned to the drum part, the strike position of the pad corresponding to the note number received changes immediately after [SETUP][MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM 1-3 and AUX 1-2 pad rims) is set to MODULATION. During recording, the sequencer data is recorded to the TD-12 in accordance with the above settings as "Pedal CC messages," "Snare CC messages," "Ride CC messages," and "Toms CC messages." The modulation effect is applied in the channel assigned to the backing part. It is not recorded to the sequencer during recording. Breath Controller (Controller number 2) Status BnH 2nd byte 02H 3rd byte vvH 0H - FH (ch.1 - 16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow n = MIDI channel number: vv = Control value: Polyphonic Key Pressure Status AnH 2nd byte kkH 3rd byte vvH 0H - FH (ch.1 - ch.16) 00H - 7FH (0 - 127) 00H - 7FH (0 - 127) * * * * A channel which is assigned to the drum part will receive only the note numbers which are specified by the drum kit. For more on note numbers, refer to "Preset Percussion Set List" (p. 92) in the Owner's Manual. If the value is greater than 40H (64), the decay of the note sounded by the received note number will be shortened. (Used in choking) When recording, this is recorded in the sequencer data itself. n = MIDI channel number: kk = note number: vv = Value: * * * Only the channel assigned to the drum part can be received. Setting [SETUP]-[MIDI]-[CTRL] Pedal CC to BREATH changes the hi-hat control pedal position. The strike position of the pad corresponding to the note number received changes immediately after [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM 1-3 and AUX 1-2 pad rims) is set to BREATH. During recording, the sequencer data is recorded to the TD-12 in accordance with the above settings as "Pedal CC messages," "Snare CC messages," "Ride CC messages," and "Toms CC messages." Copyright © 2005 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. 1 TD-12 MIDI Implementation Foot Controller (Controller number 4) Status BnH 2nd byte 04H 3rd byte vvH 0H - FH (ch.1 - ch.16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow Expression (Controller number 11) Status BnH 2nd byte 0BH 3rd byte vvH 0H - FH (ch.1 - 16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow n = MIDI channel number: vv = Control value: n = MIDI channel number: vv = Control value: * * * * Only the channel assigned to the drum part can be received. Setting [SETUP]-[MIDI]-[CTRL] Pedal CC to FOOT changes the hi-hat control pedal position. The strike position of the pad corresponding to the note number received changes immediately after [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM 1-3 and AUX 1-2 pad rims) is set to FOOT. During recording, the sequencer data is recorded to the TD-12 in accordance with the above settings as "Pedal CC messages," "Snare CC messages," "Ride CC messages," and "Toms CC messages." * * * * Only the channel assigned to the drum part can be received. Setting [SETUP]-[MIDI]-[CTRL] Pedal CC to EXPRESSION changes the hi-hat control pedal position. The strike position of the pad corresponding to the note number received changes immediately after [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM 1-3 and AUX 1-2 pad rims) is set to EXPRESSION. During recording, the sequencer data is recorded to the TD-12 in accordance with the above settings as "Pedal CC messages," "Snare CC messages," "Ride CC messages," and "Toms CC messages." Data Entry (Controller number 6, 38) Status BnH BnH 2nd byte 06H 26H 3rd byte mmH llH General Purpose Controller 1 (Controller number 16) Status BnH 2nd byte 10H 3rd byte vvH 0H - FH (ch.1 - ch.16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow n = MIDI channel number: 0H - FH (ch.1 - ch.16) mm, ll = the value of the parameter specified by RPN mm = MSB, ll = LSB * * * Only the channels assigned to the backing part can be received. Refer to the RPN item. Not recorded in the sequencer. n = MIDI channel number: vv = Control value: * * * Volume (Controller number 7) Status BnH 2nd byte 07H 3rd byte vvH * n = MIDI channel number: vv = Volume: * * 0H - FH (ch.1 - ch.16) 00H - 7FH (0 - 127) Only the channel assigned to the drum part can be received. Setting [SETUP]-[MIDI]-[CTRL] Pedal CC to GENERAL1 changes the hi-hat control pedal position. The strike position of the pad corresponding to the note number received changes immediately after [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM 1-3 and AUX 1-2 pad rims) is set to GENERAL1. During recording, the sequencer data is recorded to the TD-12 in accordance with the above settings as "Pedal CC messages," "Snare CC messages," "Ride CC messages," and "Toms CC messages." Changes the volume for the part. Not indicated in the display. Not recorded in the sequencer. General Purpose Controller 2 (Controller number 17) Status BnH 2nd byte 11H 3rd byte vvH 0H - FH (ch.1 - ch.16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow Panpot (Controller number 10) Status BnH 2nd byte 0AH 3rd byte vvH 0H - FH (ch.1 - ch.16) 00H - 40H - 7FH (Left - Center - Right) * * * n = MIDI channel number: vv = Control value: n = MIDI channel number: vv = Panpot: * * * Only the channels assigned to the backing part can be received. Changes the pan ([PATTERN]-[PART]-[MIXER]-[PAN]) for the part. Not indicated in the display. Not recorded in the sequencer. * Only the channel assigned to the drum part can be received. Setting [SETUP]-[MIDI]-[CTRL] Pedal CC to GENERAL2 changes the hi-hat control pedal position. The strike position of the pad corresponding to the note number received changes immediately after [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM 1-3 and AUX 1-2 pad rims) is set to GENERAL2. During recording, the sequencer data is recorded to the TD-12 in accordance with the above settings as "Pedal CC messages," "Snare CC messages," "Ride CC messages," and "Toms CC messages." 2 TD-12 MIDI Implementation General Purpose Controller 3 (Controller number 18) Status BnH 2nd byte 12H 3rd byte vvH 0H - FH (ch.1 - ch.16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow RPN MSB/LSB (Controller number 101, 100) Status BnH BnH 2nd byte 65H 64H 3rd byte mmH llH n = MIDI channel number: vv = Control value: n = MIDI channel number: 0H - FH (ch.1 - ch.16) mm = upper byte of parameter number specified by RPN ll = lower byte of parameter number specified by RPN << RPN >> * * * Only the channel assigned to the drum part can be received. Setting [SETUP]-[MIDI]-[CTRL] Pedal CC to GENERAL3 changes the hi-hat control pedal position. The strike position of the pad corresponding to the note number received changes immediately after [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM 1-3 and AUX 1-2 pad rims) is set to GENERAL3. During recording, the sequencer data is recorded to the TD-12 in accordance with the above settings as "Pedal CC messages," "Snare CC messages," "Ride CC messages," and "Toms CC messages." Control Changes include RPN (Registered Parameter Numbers), which are extended. When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any order) should be sent in order to select the parameter, then Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN messages are received, Data Entry messages that is received at the same MIDI channel after that are recognized as changing toward the value of the RPN messages. In order not to make any mistakes, transmitting RPN Null is recommended after setting parameters you need. Refer to "Examples of actual MIDI message" (p. 11). This device receives the following RPNs. RPN MSB, LSB 00H, 00H Data MSB, LSB mmH, --entry Explanation Pitch Bend Sensitivity mm: 00H - 18H (0 - 24 semitones) ll: ignored (processed as 00H) specify up to 2 octaves in semitone steps RPN null mm,ll: ignored set condition where RPN is unspecified. The Data Entry messages after set RPN null will be ignored. (No Data Entry messages are required after RPN null). Settings already made will not change. * General Purpose Controller 4 (Controller number 19) Status BnH 2nd byte 13H 3rd byte vvH 0H - FH (ch.1 - ch.16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow n = MIDI channel number: vv = Control value: 7FH, 7FH ---, --- * * * * Only the channel assigned to the drum part can be received. Setting [SETUP]-[MIDI]-[CTRL] Pedal CC to GENERAL4 changes the hi-hat control pedal position. The strike position of the pad corresponding to the note number received changes immediately after [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM 1-3 and AUX 1-2 pad rims) is set to GENERAL4. During recording, the sequencer data is recorded to the TD-12 in accordance with the above settings as "Pedal CC messages," "Snare CC messages," "Ride CC messages," and "Toms CC messages." * * * Only the channels assigned to the backing part can be received. Changes the bend range ([PATTERN]-[PART]-[BACKING] Bend Range) for the part. Not indicated in the display. Not recorded in the sequencer. Hold 1 (Controller number 64) Status BnH 2nd byte 40H 3rd byte vvH 0H - FH (ch.1 - ch.16) 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = O ...