User manual ROLLS HM59

LIMITED WARRANTY This product is warranted to the original consumer purchaser to be free from defects in materials and workmanship under normal installation, use and service for a period of one (1) year from the date of purchase as shown on the purchaser's receipt. The obligation of Rolls Corporation under this warranty shall be limited to repair or replacement (at our option), during the warranty period of any part which proves defective in material or workmanship under normal installation, use and service, provided the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PREPAID. Products returned to us or to an authorized Service Center must be accompanied by a copy of the purchase receipt. In the absence of such purchase receipt, the warranty period shall be one (1) year from the date of manufacture. This warranty shall be invalid if the product is damaged as a result of defacement, misuse, abuse, neglect, accident, destruction or alteration of the serial number, improper electrical voltages or currents, repair, alteration or maintenance by any person or party other than our own service facility or an authorized Service Center, or any use violative of instructions furnished by us. This one-year warranty is in lieu of all expressed warranties, obligations or liabilities. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN LIMITED WARRANTY. Some states do not allow limitations on how long an implied MIX OUTPUT MASTER LEVEL PWR HM59 Headphone Monitor Remote EXPANSION EXPANSION HEADPHONE MONITOR REMOTE EFFECTS RETURN MIX LEVELS HM59 1 2 3 4 MAIN +12 EQUALIZER 0 -12 warranty lasts, so the above limitation may not apply to you. IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental or consequential damages so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. PHONE/ LEFT RIGHT AGC COMP 64 125 250 500 1K 2K 4K 8K 16K NOTE: THIS UNIT REQUIRES A ROLLS HM60 OR HM57 FOR OPERATION. ROLLS CORPORATION SALT LAKE CITY, UTAH 3/00 OWNERS MANUAL 8 2 R123 10 HDPHN/L O UT J11 VDD 30 Q2 2N2907 4560 7 U6B 6 5 R 4 72 2 K C46 27P. 1 3 C 1 54 1U GND C5 P12A P100K X2 10U V+ C1 10U 10U R 4 92 2 K 0 C2 10U 22K R48 22K P7 P100K 6 R41 22K 2 R42 22K VCC R76 SW 2A 3 P100K P8 4 3 P H O N E 1 /4 R61 10 4 1 R60 30 U6A 2 C45 5 27P. P12B 10K NE570 DPDT R 5 73 3 K 100K R 5 12 2 K 4 6 12 11 R IG H T O U T J10 VDD VDD Q4 2N2907 THD INV DG R3 RIN U 1 9 B RC OUT 1U 0 C16 P H O N E 1 /4 GND C13 10U R77 10K SW 2B 5 4 DPDT V+ C7 10U 10 13 R52 22K R 5 83 3 K VCC C8 10U P9 P100K 5 P11B 2 4 R RET P100K X2 3 1 6 Q3 M PSA06 4560 3 P100K X2 2 R50 22K R43 22K R44 22K C65 120P. 9 14 15 16 C10 10U 6 R59 100K VCC VDD VDD 13 25 12 24 11 23 10 22 9 21 8 20 7 19 6 18 5 17 4 16 3 15 2 14 1 1 1 J16 DB25.EM ALE C34 27P. R62 18K 6 P13B 4 5 H2E 5 R67 1K C60 4560 2 3 U7A 1 3 27P. R87 C36 R92 1K C61 4560 2 U12A 1 5 8 C66 1 .5 U . H6E 4560 2 3 U11A 1 R86 10K P14B 6 4 18K 2 VCC R65 1K C48 6 5 U7B 4560 7 .0 3 9 6 1 P13A 6 3 4 R68 100K C67 1 .5 U . H1. VDD 4560 3 4560 2 8 VCC R90 1K C49 6 4560 .0 3 9 J16 DB25M ALE R93 100K U12B 7 VDD 5 2 3 2 .0 1 8 R71 1K U16A 1 5 4 5 H3A 1 VDD C35 H7A 4 H2D 4 C4 1 U 4. 6 H6D C18 P15B 3 H2C 3 1 H6C P16B 6 27P. R63 10K VCC .4 7 100KR 66 VCC C32 .0 0 8 2 3 U8A 1 3 . 0 1 8R 9 1 R88 10K R96 1K 4560 2 100K C33 U13A 1 4 1 P14A C6 5 5 H1E 1U. 1 P15A C19 4 4 3 8 VDD 8 R72 100K R69 1K 4 C20 2 H2B 2 C50 6 5 U8B 4560 7 4 2 VDD C37 4560 H4B H8B2 2 H1D .4 7 3 1 P16A R94 1K C21 C51 6 VCC 4560 U13B 7 .0 0 8 2 R97 100K VDD 5 2 2 H6B .0 0 3R 9 7 0 R75 1K R89 27P. 10K 3 3 5 4 4 8 6 P17B 4560 7 U11B 6 5 H3B 2 H7B 6 2 8 4. 2 7 C22 1 H2A 1 100K C58 3 U9A 1 VCC 3 H 11 C .2 7 . 0 0 3R 9 9 5 R100 1K 4560 2 P17A C23 100K C59 U14A 1 5 8 VCC P18B 6 R73 1K 4 H 4 . 6C 2 4 C52 6 5 U9B 4560 7 2 H6A .1 2 .0 0 2 2 2 2 3 4 8 R80 100K 4560 VDD 7 U16B 6 5 H4A H8A 1 1 3 H1B P18A .1 2 R98 1 C25 1K 6 C53 VCC 4560 .0 0 2 2 R101 100K VDD U14B 7 5 2 H8. 6 P19B 5 820P. R74 100K R83 1K 4. 0 6 8 H 4 E 5C 2 6 C56 4560 2 3 U10A 1 3 1 1 5 8 2 0 R P 9. 9 R104 1K 2 100K C57 U15A 4 4560 1 5 8 2 H8E P20B 6 4 .0 3 3 R81 1K 4 H 4 D 4C 2 8 C54 VCC 4560 6 5 U10B 7 4 8 470P. R84 100K H 11 A .0 6 8 P19A C27 3 H7C 3 H3C .0 3 3 VDD 3 P20A 1 C29 3 470P. R102 1K C55 VCC 4560 6 R105 100K VDD U15B 7 5 2 H8D 6 P21B H4C .0 1 5 4 270P. 4 R82 100K 3 P21A 4 H3D 5 1 .0 1 5 270P. 3 R103 100K 5 3 H8C R85 1K C30 .0 0 8 2 25 R64 C31 5 1K .0 0 8 2 VCC VCC C70 .1 VDD C74 .1 VDD VCC C78 .1 VDD VCC C80 .1 VDD VCC C88 .1 VDD C94 .1 VDD C95 .1 C69 .1 C73 .1 C79 .1 C81 .1 C87 .1 VCC 4 13 25 12 24 11 23 10 22 9 21 8 20 7 19 6 18 5 17 4 16 3 15 2 14 1 1 Distortion: 1 1 1 1 2 2 2 3 4 5 6 Rear Cover NE570 VCC R56 5 6 THD INV DG R3 RIN U 1 9 A RC OUT 7 R45 22K R46 C64 120P. 8 3 2 1 P6 P100K VCC Q1 M PSA06 P10B P100K X2 5 L M A IN P10A P100K X2 R M A IN P11A P100K X2 LRET VCC INTRODUCTION SPECIFICATIONS Output Impedance: Sensitivity: Power Output: Connectors: Dynamic Range: Freq. Response: Power Requirement: Dimensions: Weight: 10 Variable, -10 to +4 dB for rated output >500 mW at 32 (>150 mW at 600 ohms) 20 Hz to 20 KHz. Outputs: 1/4" TRS stereo headphone jack, DB25 jack 0.008% THD full power @ 1 KHz; 0.05% THD 20Hz to 20 KHz Greater than 96 dB 20 Hz to 20 KHz, +0, -1 dB 400 mW output Receives power from HM60 or HM57 6.25"H x 9.125"W x 1.375"D 2.5lbs. ROLLS CORPORATION 5143 South Main Street Salt Lake City, UT 84107 Title R O L L S M R H E A D P H O N E S S L A V E I I Size: H M 5 9 .S C H Rb Date: 5-Oct-1999 D ocum entN um ber TABLE OF CONTENTS Introduction Table of Contents Inspection Specifications Description Top Panel Front Panel Bottom Panel Connection Operation Block Diagram Schematic Warranty 2. Please complete the Warranty Registration Card and return it to the factory. Rev: A INSPECTION 1. Unpack and inspect the HM59 box and package. If obvious physical damage is noticed, contact the carrier immediately to make a damage claim. We suggest saving the shipping carton and packing materials for safely transporting the unit in the future. Sheet 1 of 1 Thank you for your purchase of the Rolls HM59 Headphone Monitor Remote. This unit, along with either the HM60 Headphone Monitor System or HM57 Headphone Monitor Interface, allows you to mix four mono signals with two stereo signals for your own personal monitoring needs. It includes equalization and AGC compression. Please read the following manual carefully to get the best results from your HM59. SCHEMATIC 6 BLOCK DIAGRAM DESCRIPTION TOP PANEL EXPANSION PORTS: Male and Female DB25 parallel port jacks. The output Expansion jack is female and is located on the right side of the top panel. The input Expansion jack is male and is on the left side of the top panel. MASTER OUTPUT LEVEL Headphone Output EQUALIZER COMPRESSOR FX RETURN COMRPESSOR IN/OUT +V MAIN LEVEL DB25 MULTI-PIN CONNECTOR EQUALIZER COMPRESSOR FRONT PANEL NOTE: All input signals described below are connected to either the HM60 or HM57. Refer to that unit's owners manual for proper input connection. EFFECTS RETURN: Adjusts the level of stereo signal returning from a signal processor connected to an HM60. MIX LEVELS;1 - 4 and Main: Adjust the level of input signal from the corresponding input. MASTER LEVEL: Adjusts the amount of mixed signal being sent to the Mix Output jacks. EQUALIZER: These slider controls adjust the level of the indicated frequency. For example, the 64 slider boosts or cuts the 64 Hertz component of the output signal by + or - 12 dB. The lower frequencies; 64 to 250 correspond to bass frequencies, the 500 to 2K sliders correspond to mid frequencies, and the 4K to 8K sliders adjust the high or treble frequencies. PWR: Indicates that the HM60 is connected to a power source and is on. BOTTOM PANEL MIX OUTPUT: Phone/Left: For connection to a set of stereo headphones. If a mono Tip-Sleeve plug is connected, this jack becomes the Left Output. Right: Contains the Right portion of the Output signal. Do not use this jack if you're connecting stereo headphones to the Phone/Left jack. AGC COMP: This switch engages the Automatic Gain Control compressor. EXPANSION EXPANSION -V MONO AUX LEVELS HEADPHONE MONITOR REMOTE EFFECTS RETURN PWR MIX LEVELS HM59 1 2 3 4 MAIN +12 MASTER LEVEL MIX OUTPUT -12 PHONE/ LEFT AGC COMP 64 125 250 500 1K 2K 4K 8K 16K EQUALIZER 0 5 RIGHT 2 CONNECTION CONNECTING THE HM59 Shown below is a connection diagram for the HM59. The male jack on the left is the Input, and the female jack on the right is the Output. Connect from the female OUTPUT expansion jack of either the HM60 or HM57 via the DB25 cable to the male INPUT Expansion jack on the HM59. The female OUTPUT Expansion jack on the HM59 may then be connected to another HM59 or HM58. OPERATION OPERATING THE HM59 After proper connections are made, begin sending signals to the HM60 or HM57, whichever is connected to the signal sources and your HM59. · Set the HM59 Master Level control at approximately 12 O'clock. Carefully bring up the 1-4 and Main Mix Levels until a desired mix is achieved. · Adjust the Equalizer as needed. The 64, 125, and 250 Hz sliders control the lower or bass frequencies, the 500, 1K, and 2K sliders adjust the middle frequencies, the 4K, 8K, and 16K sliders vary the high or treble frequencies. · The AGC compressor keeps transient signals like pops or feedback under control, so they won't damage your hearing. It also slightly brings up low-level signals. NOTE: Much of the signal content may not be compressed, you may not notice any effect. Only very high level or low level signals are effected. · If using external effects processors, make sure they are properly connected to the HM60, and the levels are set properly. Refer to the HM60 owners manual, as well as the operating manual of the effects processor. From HM60 or HM57 EXPANSION HEADPHONE MONITOR REMOTE EFFECTS RETURN EXPANSION PWR MIX LEVELS HM59 1 2 3 4 MAIN +12 To other HM58 or HM59 REMOTE UNITS EQUALIZER MASTER LEVEL 0 -12 MIX OUTPUT AGC PHONE/ LEFT RIGHT COMP 64 125 250 500 1K 2K 4K 8K 16K If you have an effects processor connected to the HM60 control unit, the HM59 Effects Return adjusts the level of the effected signals to your headphone mix. Note that the Effects Sends 1 - 4 and MAIN on the HM60 determine the mix of signals sent to the effects processor. The HM59 FX Return control will only adjust the level of that mix. In other words, the signals present at the Right and Left Effects Return jacks on the HM60 will be the signals adjusted by the FX Return control on the HM59. 1 2 3 4 FX SEND RIGHT STEREO INPUTS LEFT R L EXPANSION 120 VAC 50/60Hz MONO INPUTS EFFECTS RETURN EFFECTS SENDS EFFECTS RETURN PWR MIX LEVELS HEADPHONE MONITOR SYSTEM 4 MAIN +12 MASTER LEVEL 1 2 3 EQUALIZER 0 -12 MIX OUTPUT PHONE/ LEFT AGC COMP 3 RIGHT 64 125 250 500 1K 2K 4K 8K 16K 4