User manual ROLLS MP105

LIMITED WARRANTY This product is warranted to the original consumer purchaser to be free from defects in materials and workmanship under normal installation, use and service for a period of one (1) year from the date of purchase as shown on the purchaser's receipt. The obligation of Rolls Corporation under this warranty shall be limited to repair or replacement (at our option), during the warranty period of any part which proves defective in material or workmanship under normal installation, use and service, provided the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PREPAID. Products returned to us or to an authorized Service Center must be accompanied by a copy of the purchase receipt. In the absence of such purchase receipt, the warranty period shall be one (1) year from the date of manufacture. This warranty shall be invalid if the product is damaged as a result of defacement, misuse, abuse, neglect, accident, destruction or alteration of the serial number, improper electrical voltages or currents, repair, alteration or maintenance by any person or party other than our own service facility or an authorized Service Center, or any use violative of instructions furnished by us. This one-year warranty is in lieu of all expressed warranties, obligations or liabilities. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental or consequential damages so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. MP105 ROUND SOUND Tube Mic Preamp INPUT OUTPUT 12VAC NORM PAD REV PHAN CLIP PWR GAIN PHAN LEVEL +17 +75 - dB 0 Salt Lake City, UT www.bellari.com 4/00 OWNERS MANUAL INTRODUCTION Thank you for your purchase of the Bellari MP105 Round Sound Tube Mic Preamp. We are confident that this device will provide years of warm-sounding, clear and clean microphone amplification. Please take a moment and read this manual carefully as it provides all the important information you need to operate this unit properly. TABLE OF CONTENTS Introduction Table of Contents Inspection Description Top Panel Rear Panel Connection Operation Specifications Warranty SPECIFICATIONS Input Impedance: Output Impdance: THD: S/N Ratio: Maximum Input Level: Maximum Output Level: Pad: Frequency Response: XLR: 600 , 100 K Padded 1/4": 10 K 50 .15% >88 dB +12 dB XLR, +18 dB 1/4" +16 dB XLR, +10 dB 1/4" - 37 dB 20H - 25kHz +/-3 dB 1 1 1 2 3 3 3, 4, 5 6 Rear Cover INSPECTION 1. Unpack and inspect the MP105 box and package. Your MP105 was carefully packed at the factory in a protective carton. Nonetheless, be sure to examine the unit and the carton for any signs of damage that may have occurred during shipping. If obvious physical damage is noticed, contact the carrier immediately to make a damage claim. We suggest saving the shipping carton and packing materials for safely transporting the unit in the future. 2. Please complete the Warranty Registration Card and return it to the factory. FEATURES · XLR balanced and 1/4" unbalanced inputs and outputs · 20 dB Normal and Padded operation · 48 Volt Phantom Power · Clip LED Indication · Phase Reversal 1 6 OPERATION CONT. mixer. Set the MP105 LEVEL control fully counterclockwise to begin with. Set the GAIN control normally, then slowly bring up the LEVEL control to avoid overdriving the next device. - If the MP105 is used as an instrument preamp, connect the 1/4" output to your amplifier and set the levels as desired. DESCRIPTION TOP PANEL NORM/PAD: When this switch is OUT, the input signal is decreased by 37dB, when IN the signal is unaffected. PHAN: When this switch is pressed IN, 48 volts of microphone phantom power is applied to the XLR Input jack. REV: When this switch is pressed in, the phase of the XLR Output signal is reversed 180 degrees. PHAN LED: Indicates the PHAN switch is in and phantom power is being applied to the XLR Input jack. CLIP LED: Indicates that the internal signal is 3 dB before actual clipping. If this LED lights continuously, possible unwanted distortion may occur. PWR LED: Indicates the MP105 is receiving power. GAIN CONTROL: Adjusts the amount of gain or drive in the MP105 tube circuitry. LEVEL CONTROL: Adjusts the amount of output volume. NOTE: The MP105 Round Sound is designed to clip the tube before the output section actually distorts. This affords you the ability to drive the tube harder providing a warmer, more natural sound. INPUT OUTPUT 12VAC NORM PAD REV PHAN CLIP PWR GAIN PHAN LEVEL +17 +75 - dB 0 5 2 REAR PANEL INPUT: 1/4" TS unbalanced and XLR balanced input jacks. OUTPUT: 1/4" TS unbalanced and XLR balanced input jacks. 12VAC: Connects to the supplied Rolls/Bellari PS12 12 volt AC adapter. MIXER OR DIGITAL RECORDER INPUT OUTPUT 12VAC 12VAC OUTPUTS INPUTS CONNECTION First, make sure the MP105 power supply is connected to an AC outlet. Connect the microphone to the MP105 input jack, press in the PHAN switch if the microphone is a condenser type and requires phantom power. Connect the MP105 Output to the Input of a digital recorder or mixer via either the XLR or 1/4" jack. NORM PAD REV PHAN CLIP PWR GAIN PHAN LEVEL +17 +75 - dB 0 Fig. 1 OPERATION The MP105 amplifies your microphone signal to a professional line level. That signal may then be sent to a digital recorder, mixing console, or signal processor. Shown in Fig. 1 is an example of how to connect a microphone to the MP105, and then to the input of a recorder or mixer. - If you connect the MP105 XLR Output jack to an XLR input on a mixer, you may be using the mixer channel's mic preamps. This may result in distortion. If this happens, use the MP105 1/4" Output to a 1/4" line input on the mixer. Speak or sing into the microphone at the volume level used during performance. Set the GAIN control so the CLIP LED lights occasionally - only during the extremely loud parts. Adjust the MP105 output LEVEL control so the input level indicators on the recorder or mixer show a desirable amount. If your microphone puts out a high level of power, or if you are connecting a balanced line-level signal to the MP105, try setting the NORM/PAD switch to the out or PAD position. The Phase Reverse (REV) switch is used to change the phase of the output signal 180 degrees from that of the input. This is for correcting possible wiring mismatches, or microphone phase mismatches. INSTRUMENT PREAMP The MP105 may be used as an instrument preamp or direct box. Connect your instrument to the 1/4" unbalanced input. - If using the MP105 as a direct box, use the XLR output and connect to the 3 4