User manual ROLLS RA63S

LIMITED WARRANTY This product is warranted to the original consumer purchaser to be free from defects in materials and workmanship under normal installation, use and service for a period of one (1) year from the date of purchase as shown on the purchaser's receipt. The obligation of Rolls Corporation under this warranty shall be limited to repair or replacement (at our option), during the warranty period of any part which proves defective in material or workmanship under normal installation, use and service, provided the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PREPAID. Products returned to us or to an authorized Service Center must be accompanied by a copy of the purchase receipt. In the absence of such purchase receipt, the warranty period shall be one (1) year from the date of manufacture. This warranty shall be invalid if the product is damaged as a result of defacement, misuse, abuse, neglect, accident, destruction or alteration of the serial number, improper electrical voltages or currents, repair, alteration or maintenance by any person or party other than our own service facility or an authorized Service Center, or any use violative of instructions furnished by us. This one-year warranty is in lieu of all expressed warranties, obligations or liabilities. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental or consequential damages so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RA63s DISTRIBUTION AMPLIFIER MONO 1 2 3 4 5 STEREO 1 2 LEFT 3 4 1 6 7 8 GAIN 0 dB +20 dB DISTRIBUTION AMPLIFIER 8 Channel Mono 4 Channel Stereo pwr 2 RIGHT 3 4 FEATURES · Stereo 4 channel, Mono 8 channel audio distribution · Screw driver adjustable front panel volume controls · Balanced inputs and outputs SPECIFICATIONS Input Impedance: Max Input Level: I/O Connectors: Output Impedance: Max Output Level: Max Gain: S/N Ratio: Frequency Response: THD: Power: Size: Weight: 100 K balanced +22 dBV Screw terminal; + -, and ground 50 balanced +24 dB 20 dB >90 dB 10 Hz - 40 kHz, +/- 1 dB <.008% 120 VAC 50-60 Hz, 15VA 19" x 1.75" x 6.5" (48 x 4.5 x 17 cm) 7 lbs. (3 kg) ROLLS CORPORATION SALT LAKE CITY, UTAH 11/03 OWNERS MANUAL INTRODUCTION Thank you for your purchase of the ROLLS RA63s Distribution Amplifier. This unit will distribute a mono signal to eight outputs, or a stereo signal to four right and four left outputs. The outputs are designed to drive high-level balanced lines in a sound distribution system. The screw terminals on the rear panel are for input and output, and each output may power more than one line. NOTE: THIS MANUAL ASSUMES THE USER HAS A BASIC WORKING KNOWLEDGE OF AUDIO ELECTRONICS, BALANCED AND UNBALANCED CONNECTIONS, AND PROPER SIGNAL LEVEL SETTING. DESCRIPTION FRONT PANEL MONO INSTALLATION Install the RA63s in a standard 19" rack. The unit is intended for installations where several zones or areas need to be controlled and a high level balanced signal is required to drive the input lines. STEREO/MONO CONFIGURATION To change the stereo/mono configuration of the RA63s, begin by carefully removing the lid. Behind the Channels 5 and 6 level potentiometers is the 4X2 / 8X1 jumper. For stereo operation place the jumper in the 4X2 position, and for mono operation place the jumper in the 8X1 position. Mark the Configuration pad on the rear panel with a felt tip pen so you know which mode the RA63s is in. Replace the lid. 1 2 3 4 5 6 7 8 GAIN 0 dB +20 dB DISTRIBUTION AMPLIFIER 8 Channel Mono 4 Channel Stereo pwr STEREO 1 2 LEFT 3 4 1 2 RIGHT 3 4 Mono 1 - 8 / Stereo 1 - 4: These screwdriver-adjustable controls vary the level of signal for each indicated output. +20dB/0dB Gain switch: Pressing this switch in provides 20 dB of gain to the input signal. pwr: LED indicating the unit's power status. REAR PANEL INPUTS MODEL RA63s SERIAL NUMBER 63sMADE IN U.S.A. 120 VAC 50/60 Hz 15 VA SCHEMATIC right/ mono left 8 4 7 3 RIGHT 6 2 OUTPUTS 5 4 1 4 RISQUE DE CHOC - NE PAS ENLEVER 3 3 LEFT 2 2 1 1 MONO STEREO CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN -+ CONFIGURATION MONO: STEREO: -+-+ -+ -+ -+ -+ -+ -+ -+ WARNING: DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER. NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL 120 VAC 50/60 HZ 15 VA: Power Cord. Connect to a properly grounded AC source. CONFIGURATION PAD: These label pads are included for you to mark how the RA63s is configured; either MONO 8 channel, or STEREO 4 channel. Use a felttip pen, and mark the pad indicating the RA63s configuration. INPUTS Right/Mono and Left: These five terminals, labeled + for the positive or "hot" connection, - for the negative connection, and the ground symbol for earth ground connection are for connection to the balanced or unbalanced input signal(s) to be distributed. MONO 1 - 8, STEREO 1 - 4: For each channel; the two terminals labeled + for the positive or "hot" portion of the output signal, and the - for negative or neutral portion. The ground signal indicates the terminal to be connected to earth ground. _________________________________________________________________ CONNECTION -+ + = In-phase or "Hot" - = Out-of-phase or "Negative" (NOTE: This is NOT a ground connection) = Ground