Side-Loading AnoSkyBoxTM Parts Instruction Sheet 32 Corner Brackets 12 AnoFrame Rails 12AF-100 8 AnoFrame split rails Instructions for assembly Note: You will be assembling four frames. Below instructions are for one frame only. Repeat steps 1 & 2 for each frame. Step 1 Locate two split rails and a solid rail that is the same length as the split rails. Insert two corner brackets in each end of the solid side AnoFrame rail. Insert one corner bracket into each end of each split side AnoFrame rails. Fig. 1. Note: Tension tabs on corner brackets face towards outside of frame rails. solid rail Figure 1 solid rail split rails 1 2 solid rail Step 2 Assemble frame following steps in Fig. 2 sliding sides together in the order shown. split rails 3 4 Figure 2 The AnoSkyboxTM is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #03INSSideLoadingAnoSkyBox 35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays.com Incept-1.24.03 Side-Loading AnoSkyBoxTM Parts Instruction Sheet 8 Corner Braces 4 Spine Rails 1 Ball Head Screwdriver 8 Screws 4 Hanger Tabs Instructions for assembly Step 3 Attach one corner brace onto one end of each corner spine. Fig. 3. Step 4 Screw into place and tighten. Fig. 4. Step 5 Lay out AnoSkyBox parts as shown. Be sure to lay out frames so each corner contains matching frame sides -- two corners should contain only split rails and two corners should contain only solid rails. Fig. 5. Note: Once side of each frame contains split rails. When laying out your AnoSkybox, make sure you match the split rail sides of both frames to the same corner spine. You should have only 2 corners containing split rails. Figure 3 Figure 4 split rails solid rail solid rail split rails Figure 5 The AnoSkyboxTM is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #03INSSideLoadingAnoSkyBox 35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays.com Incept-1.24.03 Side-Loading AnoSkyBoxTM Parts Instruction Sheet 8 Corner Braces 4 Spine Rails 1 Ball Head Screwdriver 8 Screws 4 Hanger Tabs Instructions for assembly Step 6 Attach frames to corner spines. Be sure to insert bottom rib of corner brace into bottom channel of the AnoFrame rail, as shown in Fig. 6. Repeat for all frames. Fig. 7. Step 7 Attach one corner brace onto the top of each corner spine rail. Fig. 8. Figure 6 Figure 7 Step 8 If using the cable and loop for hanging, insert loop into hanger tab. If using the cable and saucer for hanging, insert saucer into hanger tab. Fig. 9. Step 9 Insert one screw into each hanger tab and align with hole in top corner brace. Fig. 10. Figure 8 Figure 9 Step 10 Screw hanger tab into place. Fig. 11. Figure 10 Figure 11 The AnoSkyboxTM is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #03INSSideLoadingAnoSkyBox 35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays.com Incept-1.24.03 Side-Loading AnoSkyBoxTM Parts Instruction Sheet 2 Velcro Straps Instructions for assembly Step 11 Insert one Velcro strap through each corner containing split rails. Slide the strap through the split rails. Fig. 12. Step 12 Tighten and secure in place on the inside of the AnoSkyBox. Fig. 13. Figure 12 Figure 13 Step 13 Suspend AnoSkyBox through hanger tabs with appropriate Rose Displays hanging accessories. Step 14 Insert graphics. Fig. 14. Figure 14 The AnoSkyboxTM is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSSideLoadingAnoSkyBox 35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays.com Incept-1.24.03 ...