DX6000_USA 18.11.2003 11:29 Uhr Seite 1 Garment has not been rinsed sufficiently. Iron is leaking Over use of burst button. Distilled or softened water being used. Ensure garments are rinsed thoroughly to remove any detergent desposits or chemicals on new garments. Allow more time between each burst. See section "Water recommendations". Switch to spring water or mix tap water with distilled water. Do not fill past max line on tank. Be sure to close the cover at filling inlet. Move iron or shake gently to reactivate. Spray reverse side of fabric and allow starch to penetrate. Be sure to set temperature according to fabric being ironed. Fill with water. Hold cold iron horizontally. Place finger over the spray nozzle to create a vacuum. Press the spray button 4 to 5 times. Remove finger from nozzle, press spray button a few more times. 4 Vapodur Valve To ensure the iron continues to steam efficiently, open and close the valve a few times after each use. This is done by moving the variable steam control lever left to right a few times. Service center information is subject to change. Please visit our website at www.rowentausa.com or call our service center information line at 781-306-4620. The information line provides current service center information and listings in California. 5 6 7 8 POWER DUO After ironing 1. Turn the temperature dial to the min setting. Slide the steam lever to the no steam position . 2. Unplug the appliance. 3. Place the iron on its heel and allow to cool completely. 4. Empty water from the appliance before storing. We recommend emptying the iron when not in use. 5. To protect the soleplate, we recommend storing iron on its heel. The Auto off light is flashing. Build up on the soleplate. Overfilled. Appliance description 1 Spray button 2 Burst of steam and Pro Vertical Steam button 3 Variable steam control with self clean function 4 Auto off light (depending on model) 5 Thermostat light 6 Temperature control dial 7 Water filling inlet (covered depending on model) 8 Spray nozzle 9 Cord 10 Cord support 11 Water tank with maximum water level indicator 12 Soleplate Auto-off has engaged. (depending on model) Starch use. Burnt material. Ironing at too high temperature. Cleaning and Maintenance When cold and unplugged, the iron can be cleaned with a damp cloth and wiped dry. Never use household cleaners or solvents. Cleaning the soleplate Rowenta soleplates have excellent non-stick properties and can be wiped clean when cold. · In normal use a draggy coating may build up on the soleplate (starch, detergent build-up, burnt synthetic fibers). This can be easily removed by using the Rowenta Soleplate Kit or a quality hot iron soleplate cleaner available at most stores. The Rowenta kit is also available through our website: www.rowentausa.com · To prevent scratching of the soleplate, do not iron over sharp objects (zippers, etc.). Do not place the iron on rough surfaces, e.g. metal iron support, which may scratch the soleplate. Spray function does not work. Priming may be necessary on first use. 110 389 7423 If troubleshooting does not assist, before consulting the retailer regarding their return/exchange policy, please telephone consumer service at 781-396-0600. Rowenta Werke GmbH, 63016 Offenbach am Main SE CLE LF AN · Fill the iron with tap water to the max mark on the water tank. · Be sure that variable steam lever is set to minimum. · Stand iron on heel and plug in. · Set thermostat to ··· setting. · Once heated, unplug iron. · Hold iron horizontally over the sink with the soleplate pointing away from body. · Move the variable steam lever completely to the right and hold in the self clean position for one minute. Warning: Doing this will cause steam and hot water to be ejected from the soleplate. Take all proper precautions and hold iron away from body. · Move the iron gently back and forth and side to side until all water has run through plate. · Carefully wipe all water and material from the soleplate with an old towel, as the water and minerals can stain the soleplate (although this has no effect on glide of performance.) Warning: Iron and soleplate may still be very hot. Exercise care while wiping. · Place iron on heel and leave to cool. Before using iron after self cleaning, test steam and burst of steam on an old towel or cloth than can be discarded. SELF CLEAN Troubleshooting Issues Iron does not heat. In the interest of improving products, Rowenta reserves the right to change specifications without prior notice. Possible causes Not properly plugged in. The temperature control is set too low. Auto-off has engaged (depending on model). Solutions Check that iron is plugged in correctly. Set the temperature control to a higher temperature. Move iron or shake it gently to reactivate. Fill the water tank. See section called "steam ironing". Wait for the soleplate to reach the correct temperature. See section "Water recommendations". Switch to spring water or mix tap water with distilled water. LIMITED WARRANTY This Rowenta product is warranted against defects in material and workmanship for one year from the initial purchase date. During this period any Rowenta product owned by the original purchaser that, upon inspection by Rowenta, is proved defective, will be repaired or replaced, at Rowenta's option, without charge to the customer. If a replacement product is sent, it will carry the remaining warranty of the original product. This warranty does not apply to any defect arising from a buyer's or user's misuse of the product, negligence, failure to follow Rowenta's instructions, use on current or voltage other than stamped on the product or alteration or repair not authorized by Rowenta. Repair or disassembly by anyone other than a Rowenta authorized service center will void the warranty. THE WARRANTIES SET FORTH HEREIN ARE EXCLUSIVE AND NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, ARE MADE BY ROWENTA OR ARE AUTHORIZED TO BE MADE WITH RESPECT TO THE PRODUCT. ROWENTA'S SOLE OBLIGATION IN THE EVENT OF A DEFECTIVE PRODUCT SHALL BE TO REPAIR OR REPLACE, IN ROWENTA'S SOLE DISCRETION, THE DEFECTIVE PRODUCT. IN NO EVENT SHALL ROWENTA BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL LOSSES OR DAMAGES (INCLUDING BUT NOT LIMITED TO INTERRUPTION OF BUSINESS OR LOSS OF BUSINESS OR PROFIT) RESULTING FROM THE USE OF OR INABILITY TO USE THE PRODUCT, ANY BREACH OF WARRANTY OR ANY DEFECT IN THE PRODUCT EVEN IF ROWENTA SHALL HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH POTENTIAL LOSSES OR DAMAGES. If you believe your product is defective, bring the product (or send it, postage prepaid) along with proof of purchase to the nearest authorized Rowenta Service Center (see below). If you send the product, please include a letter explaining the nature of the claimed defect. Rowenta 196 Boston Avenue Medford, MA 02155 Tel.: (781)396-0600 www.rowentausa.com OFFICE LOCATION ONLY. To service product see service center information below. If your appliance needs service, ship the product to your nearest regional service center. Be sure to put your name on the outside of shipping box (no P.O. boxes please). If in warranty, Rowenta will repair or replace product at their discretion. If the product is out of warranty, you will be advised of the cost of repair before any work begins. Our main service centers are listed below: Turnpike Appliance 3495A Lawson Blvd. Oceanside, NY 11572 516-483-5596 Authorized Appliance 1644 West Ogden Ave. Downers Grove, IL 60515 630-852-1550 Not enough steam. There is insufficient water in the tank. Iron is not set to a steam setting. The Anti-drip function is active. POWER DUO 1 2 3 10 9 Iron is emitting a brown or white substance. Water may need to be changed due to hardness or organic matter. 11 12 DX6000_USA 18.11.2003 11:29 Uhr Seite 2 IMPORTANT SAFETY INSTRUCTIONS When using this appliance, basic safety precautions should always be followed including the following: Read all instructions before using this product. · Use appliance only for its intended use. · To protect against a risk of electric shock, do not immerse the appliance in water or other liquids. · The appliance should always be turned off before plugging or unplugging from outlet. Never yank the cord to disconnect from outlet, instead grasp plug and pull to disconnect. · Always disconnect appliance from electrical outlet when filling with water or emptying when not in use. · Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing. · Do not operate appliance with a damaged cord or if appliance has been dropped or damaged. · To avoid the risk of electric shock, do not disassemble the appliance. Ship it to the nearest authorized Rowenta approved service center for examination and repair. Incorrect reassembly can cause a risk of electric shock when the appliance is used. · Not intended for use by children. Close supervision is necessary for any appliance being used near children. Unsupervised use can result in fire or personal injury. Do not leave appliance unattended while plugged in, on an ironing board, or while it is still hot. · Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down. There may be hot water in the reservoir. · Do not direct steam at people, animals or iron clothes while they are being worn. · The use of accessory attachments is not recommended by Rowenta and may result in fire, electric shock or personal injury. Before use · Remove soleplate cover before using iron. · Remove all packaging from the iron. · Please read all of the Instructions for Use and the Important Safety Guards carefully. · It is normal for a small amount of smoke and a light odor to be produced the first time it is used. This will quickly disappear. · Particles may emit from iron during first use. They are not harmful and should disappear after the iron has been allowed to steam. Filling with water · Ensure the iron is unplugged. · Slide the variable steam lever to the left ( ). · Rest the iron on heel and tilt it forward approximately 1 inch. If the iron is equipped with a covered filling inlet, open the filling inlet by sliding the cover down. · Fill with water (containing no additives) to the max mark on the water tank. We recommend using a water pitcher rather than filling under the tap. · If equipped with filling inlet cover, slide cover to close. If you need to add water during ironing, UNPLUG the iron and follow the steps above. Ensure iron heats back to temperature afterwards, that means thermostat light will go out. Selecting the Temperature Set the temperature control dial according to the fabric you are ironing. Check the garments label for appropriate setting. We recommend using the chart below as a guide. PRO Vertical Steam (depending on model) To be used at maximum temperature setting ··· . This feature generates a powerful vertical steam and is ideal for removing creases from hanging clothes (e.g. suits, jackets, shirts), hanging curtains etc. · Hang up garment on a hanger. · Set the variable steam control to position. · Hold the iron a few inches away from the garment to avoid burning delicate fabrics. · Press the PRO Vertical Steam button every 2 seconds to generate a steady flow of steam. · Moving the iron from top to bottom. When using PRO Vertical Steam, we recommend periodically placing the iron down to allow it to reheat. Before placing the iron on its heel, wait for the steam flow to finish. As the steam is very hot in the beginning it will be not visible. You will hear the steam function engage and after few bursts it will be visable. Warning! Never direct the steam jet at persons or animals. Ironing label Fabric Synthetics e.g. polyester, silk, viscose Temperature control Wool Cotton, linen Light will be on as iron is heating. When light goes out iron is ready to use. When heating a cold iron, please allow thermostat to cycle twice before use (thermostat light will go on and off twice). Helpful Hints · When ironing, start with fabrics that require a low temperature setting (·) and finish with those which need the highest temperature (···). · Mixed fiber fabrics should be ironed on the temperature for the most delicate fabrics. For example a shirt that is 60% cotton and 40% polyester should be ironed at the (·) setting for synthetics. · If spray starch is used, spray it onto the reverse side of the garment. Allow starch to penetrate before ironing by setting garment aside for 30 seconds. · For best results, use a mesh type ironing board to allow excess steam to escape. · For delicate fabrics, we recommend carrying out a test on an unobtrusive area of the garment such as an inner seam. · Adhere to manufacturer rec ...