User manual RYOBI DP121L

OPERATOR'S MANUAL 12 in. DIGITAL DRILL PRESS DP121L Your drill press has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for your purchase. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS Introduction ..................................................................................................................................................................... Warranty .......................................................................................................................................................................... General Safety Rules .................................................................................................................................................... 3-4 Specific Safety Rules....................................................................................................................................................... 5 Symbols ........................................................................................................................................................................ 6-7 Electrical .......................................................................................................................................................................... 8 Glossary of Terms ............................................................................................................................................................ 9 Features .................................................................................................................................................................... 10-11 Tools Needed................................................................................................................................................................. 11 Loose Parts ................................................................................................................................................................... 1 Assembly .................................................................................................................................................................. 13-17 Operation .................................................................................................................................................................. 18-0 Adjustments................................................................................................................................................................... 1 Maintenance .................................................................................................................................................................. Troubleshooting ............................................................................................................................................................. 3 Parts Ordering / Service ................................................................................................................................... Back Page INTRODUCTION This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability have been given top priority in the design of this product making it easy to maintain and operate. WARRANTy RyOBI® POWER TOOL - LIMITED TWO yEAR WARRANTy AND 30 DAy EXCHANGE POLICy Techtronic Industries North America, Inc., warrants its RYOBI® power tools with the following conditions: 30-DAy EXCHANGE POLICy: During the first 30 days after date of purchase, you may either request service under this warranty or you may exchange any RYOBI® power tool which does not work properly due to defective workmanship or materials by returning the power tool to the dealer from which it was purchased. To receive a replacement power tool or requested warranty service, you must present proof of purchase and return all original equipment packaged with the original product. The replacement power tool will be covered by the limited warranty for the balance of the two year period from the date of the original purchase. WHAT THIS WARRANTy COVERS: This warranty covers all defects in workmanship or materials in your RYOBI® power tool for a period of two years from the date of purchase. With the exception of batteries, power tool accessories are warranted for ninety (90) days. Batteries are warranted for two years. HOW TO GET SERVICE: Just return the power tool, properly packaged and postage prepaid, to an Authorized Service Center. You can obtain the location of the Service Center nearest you by contacting a service representative at Techtronic Industries North America, Inc., P.O. Box 107, Anderson, SC 96-107, by calling 1-800-55-579 or by logging on to www.ryobitools.com. When you request warranty service, you must also present proof of purchase documentation, which includes the date of purchase (for example, a bill of sale). We will repair any faulty workmanship, and either repair or replace any defective part, at our option. We will do so without any charge to you. We will complete the work in a reasonable time, but, in any case, within ninety (90) days or less. WHAT'S NOT COVERED: This warranty applies only to the original purchaser at retail and may not be transferred. This warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defects resulting from misuse, abuse, neglect, alteration, modification or repairs by other than Authorized Service Centers. Techtronic Industries North America, Inc. makes no warranties, representations or promises as to the quality or performance of its power tools other than those specifically stated in this warranty. ADDITIONAL LIMITATIONS: Any implied warranties granted under state law, including warranties of merchantability or fitness for a particular purpose, are limited to two years from the date of purchase. Techtronic Industries North America, Inc. is not responsible for direct, indirect, or incidental damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. GENERAL SAFETy RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. ALWAyS WEAR SAFETy GLASSES WITH SIDE SHIELDS. Everyday eyeglasses have only impactresistant lenses, they are NOT safety glasses. SECURE WORK. Use clamps or a vise to hold work when practical, it is safer than using your hand and frees both hands to operate the tool. NOT OVERREACH. Keep proper footing and balance DO at all times. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. DISCONNECT TOOLS. When not in use, before servicing, or when changing attachments, blades, bits, cutters, etc., all tools should be disconnected from power source. AVOID ACCIDENTAL STARTING. Be sure switch is off when plugging in any tool. USE RECOMMENDED ACCESSORIES. Consult the operator's manual for recommended accessories. The use of improper accessories may result in injury. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury. USE THE RIGHT DIRECTION OF FEED. Feed work into a blade, cutter, or sanding spindle against the direction or rotation of the blade, cutter, or sanding spindle only. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN THE POWER OFF. Don't leave tool until it comes to a complete stop. PROTECT yOUR LUNGS. Wear a face or dust mask if the cutting operation is dusty. PROTECT yOUR HEARING. Wear hearing protection during extended periods of operation. NOT ABUSE CORD. Never carry tool by the cord or DO yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges. USE OUTDOOR EXTENSION CORDS. When tool is used outdoors, use only extension cords with approved ground connection that are intended for use outdoors and so marked. STAy ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush. 3 READ ALL INSTRUCTIONS KNOW yOUR POWER TOOL. Read the operator's manual carefully. Learn the applications and limitations as well as the specific potential hazards related to this tool. U A R D A G A I N S T E L E C T R I C A L S H O C K B y G PREVENTING BODy CONTACT WITH GROUNDED SURFACES. For example: pipes, radiators, ranges, refrigerator enclosures. KEEP GUARDS IN PLACE and in good working order. REMOVE ADJUSTING KEyS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. DO NOT leave tools or pieces of wood on the tool while it is in operation. NOT USE IN DANGEROUS ENVIRONMENTS. Do DO not use power tools in damp or wet locations or expose to rain. Keep the work area well lit. KEEP CHILDREN AND VISITORS AWAy. All visitors should wear safety glasses and be kept a safe distance from work area. Do not let visitors contact tool or extension cord while operating. MAKE WORKSHOP CHILDPROOF with padlocks, master switches, or by removing starter keys. DON'T FORCE THE TOOL. It will do the job better and safer at the feed rate for which it was designed. USE THE RIGHT TOOL. Do not force the tool or attachment to do a job for which it was not designed. USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Use only a cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gauge size (A.W.G.) of at least 16 is recommended for an extension cord 50 feet or less in length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. DRESS PROPERLy. Do not wear loose clothing, gloves, neckties, or jewelry that can get caught and draw you into moving parts. Rubber gloves and nonskid footwear are recommended when working outdoors. Also wear protective hair covering to contain long hair. GENERAL SAFETy RULES NOT USE TOOL IF SWITCH DOES NOT TURN IT DO ON AND OFF. Have defective switches replaced by an authorized service center. ALWAyS TURN SWITCH OFF before disconnecting it to avoid accidental starting. NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes. INSPECT TOOL CORDS PERIODICALLy. If damaged, have repaired by a qualified service technician at an authorized service facility. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Repair or replace a damaged or worn cord immediately. Stay constantly aware of cord location and keep it well away from the rotating blade. INSPECT EXTENSION CORDS PERIODICALLy and replace if damaged. GROUND ALL TOOLS. If tool is equipped with threeprong plug, it should be plugged into a three-hole electrical receptacle. USE ONLy CORRECT ELECTRICAL DEVICES: 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. KEEP TOOL DRy, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool. NEVER START A TOOL WHEN ANy ROTATING COMPONENT IS IN CONTACT WITH THE WORKPIECE. DO NOT OPERATE A TOOL WHILE UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR ANy MEDICATION. WHEN SERVICING use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. USE ONLy RECOMMENDED ACCESSORIES listed in this manual or addendums. Use of accessories that are not listed may cause the risk of personal injury. Instructions for safe use of accessories are included with the accessory. 4 SPECIFIC SAFETy RULES KEEP BITS CLEAN AND SHARP. Sharp bits minimize stalling. Dirty and dull bits may cause misalignment of the material and possible operator injury. KEEP HANDS AWAy FROM WORK AREA. Keep hands away from the bit. Restrain any loose clothing, jewelry, long hair, etc., that may become entangled in the bit. ALWAyS CLAMP WORKPIECE AND BRACE AGAINST COLUMN TO PREVENT ROTATION. Never use your hand to hold the object while drilling. USE RECOMMENDED SPEED FOR DRILL ACCESSORy AND WORKPIECE MATERIAL. SURE DRILL BIT OR CUTTING TOOL IS SECURELy BE LOCKED IN THE CHUCK. SURE CHUCK KEy IS REMOVED from the chuck BE before connecting to power source or turning power ON. ADJUST THE TABLE OR DEPTH STOP TO AVOID DRILLING INTO THE TABLE. Shut off the power, remove the drill bit, and clean the table before leaving machine. AVOID DIRECT EyE EXPOSURE when using the laser guide. ALWAyS ENSURE THE LASER BEAM IS AIMED AT A SURFACE WITHOUT REFLECTIVE PROPERTIES. Shiny reflective materials are not suitable for laser use. NEVER PLACE yOUR FINGERS IN A POSITION WHERE THEy COULD CONTACT THE DRILL or other cutting tool if the workpiece should unexpectedly shift. NEVER PERFORM ANy OPERATION by moving the head or table with respect to one another. Do not turn the motor switch ON or start any operation before checking that the head and table support lock handle is clamped tight to column and head and table support collars are correctly positioned. BEFORE ENGAGING THE POWER SWITCH, MAKE SURE THE BELT GUARD IS DOWN AND THE CHUCK IS INSTALLED PROPERLy. LOCK THE MOTOR SWITCH OFF WHEN LEAVING THE DRILL PRESS. Do not perform layout, assembly, or set-up work on the table while the cutting tool is rotating, switched on, or connected to a power source. SAVE THESE INSTRUCTIONS. Refer to them frequently and use to instruct other users. If you loan someone this tool, loan them these instructions also. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: · lead from lead-based paints, · crystalline silica from bricks and cement and other masonry products, and · arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. 5 SyMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SyMBOL V A Hz W min Volts Amperes Hertz Watt Minutes Alternating Current Direct Current no No Load Speed Class II Construction .../min Per Minute Wet Conditions Alert NAME Voltage Current Frequency (cycles per second) Power Time Type of current Type or a characteristic of current Rotational speed, at no load Double-insulated construction Revolutions, strokes, surface speed, orbits etc., per minute Do not expose to rain or use in damp locations. To reduce the risk of injury, user must read and understand operator's manual before using this product. Always wear safety goggles or safety glasses with side shields and a full face shield when operating this product. Precautions that involve your safety. Failure to keep your hands away from the blade will result in serious personal injury. To reduce the risk of injury or damage, avoid contact with any hot surface. DESIGNATION/EXPLANATION Read The Operator's Manual Eye Protection Safety Alert No Hands Symbol Hot Surface 6 SyMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SyMBOL SIGNAL MEANING Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. (Without Safety Alert Symbol) Indicates a situation that may result in property damage. DANGER: WARNING: CAUTION: CAUTION: SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When servicing, use only identical replacement parts. WARNING: To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely the operator's manual. Save this operator's manual and review frequently for continuing safe operation and instructing others who may use this product. WARNING: The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1. SAVE THESE INSTRUCTIONS 7 ELECTRICAL EXTENSION CORDS Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat. Use the chart provided below to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter's Laboratories (UL) should be used. **Ampere rating (on tool faceplate) 0-.0 .1-3.4 3.5-5.0 5.1-7.0 7.1-1.0 1.1-16.0 SPEED AND WIRING The no-load speed of this tool is approximately 3,000 rpm. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor's horsepower rating. A line intended only for lights cannot properly carry a power tool motor. Wire that is heavy enough for a short distance will be too light for a greater distance. A line that can support one power tool may not be able to support two or three tools. GROUNDING INSTRUCTIONS In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Repair or replace a damaged or worn cord immediately. This tool is intended for use on a circuit that has an outlet like the one shown in figure 1. It also has a grounding pin like the one shown. Cord Length 5' 50' 100' 16 16 16 16 16 16 Wire Size (A.W.G.) 16 16 14 16 14 1 14 14 10 14 1 -- **Used on 12 gauge - 20 amp circuit. NOTE: AWG = American Wire Gauge When working with the tool outdoors, use an extension cord that is designed for outside use. This is indicated by the letters "WA" on the cord's jacket. Before using an extension cord, inspect it for loose or exposed wires, and cut or worn insulation. WARNING: Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools, or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury. WARNING: Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury. ELECTRICAL CONNECTION This tool is powered by a precision built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the tool does not operate when plugged into an outlet, double check the power supply. GroundinG Pin 120V Grounded outlet Fig. 1 8 GLOSSARy OF TERMS Anti-Kickback Pawls (radial arm and table saws) A device which, when properly installed and maintained, is designed to stop the workpiece from being kicked back toward the front of the saw during a ripping operation. Arbor The shaft on which a blade or cutting tool is mounted. Bevel Cut A cutting operation made with the blade at any angle other than 90° to the table surface. Chamfer A cut removing a wedge from a block so the end (or part of the end) is angled rather than at 90°. Compound Cut A cross cut made with both a miter and a bevel angle. Crosscut A cutting or shaping operation made across the grain or the width of the workpiece. Cutter Head (planers and jointers) A rotating piece of adjustable blades. The cutter head removes material from the workpiece. Dado Cut A non-through cut which produces a square-sided notch or trough in the workpiece (requires a special blade). Featherboard A device used to help control the workpiece by guiding it securely against the table or fence during any ripping operation. FPM or SPM Feet per minute (or strokes per minute), used in reference to blade movement. Freehand Performing a cut without the workpiece being guided by a fence, miter gauge, or other aids. Gum A sticky, sap-based residue from wood products. Heel Alignment of the blade to the fence. Kerf The material removed by the blade in a through cut or the slot produced by the blade in a non-through or partial cut. Kickback A hazard that can occur when the blade binds or stalls, throwing the workpiece back toward operator. Leading End The end of the workpiece pushed into the tool first. Miter Cut A cutting operation made with the workpiece at any angle to the blade other than 90°. Non-Through Cuts Any cutting operation where the blade does not extend completely through the thickness of the workpiece. Pilot Hole (drill presses) A small hole drilled in a workpiece that serves as a guide for drilling large holes accurately. Push Blocks and Push Sticks Devices used to feed the workpiece through the saw blade during cutting operations. A push stick (not a push block) should be used for narrow ripping operations. These aids help keep the operator's hands well away from the blade. Resaw A cutting operation to reduce the thickness of the workpiece to make thinner pieces. Resin A sticky, sap-based substance that has hardened. Revolutions Per Minute (RPM) The number of turns completed by a spinning object in one minute. Ripping or Rip Cut A cutting operation along the length of the workpiece. Riving Knife (table saws) Also known as a spreader or splitter. A metal piece, slightly thinner than the saw blade, which helps keep the kerf open and also helps to prevent kickback. Saw Blade Path The area over, under, behind, or in front of the blade. As it applies to the workpiece, that area which will be or has been cut by the blade. Set The distance that the tip of the saw blade tooth is bent (or set) outward from the face of the blade. Snipe (planers) Depression made at either end of a workpiece by cutter blades when the workpiece is not properly supported. Through Sawing Any cutting operation where the blade extends completely through the thickness of the workpiece. Throw-Back The throwing back of a workpiece usually caused by the workpiece being dropped into the blade or being placed inadvertently in contact with the blade. Workpiece or Material The item on which the operation is being done. Worktable Surface where the workpiece rests while performing a cutting, drilling, planing, or sanding operation. 9 FEATURES PRODUCT SPECIFICATIONS Chuck ........................................................................ 1/ in. Input ............................... 10 Volt, 60Hz, AC Only, 5 Amps Motor ........................................................ 1/3 HP Induction No Load Speed ......................................... 500­3,000 RPM Swing.......................................................................... 1 in. Spindle Travel ............................................................... 3 in. Table Size ......................................................10-3/4 in. dia. Table Movement ...............................45° bevel, 360° swivel Overall Height ............................................................. 35 in. Net Weight ............................................................. 95.9 lbs. laser Variable sPeed leVer workliGht laser on/off switch feed handle switch key dePth GauGe Power switch sPindle lock leVer workliGht on/off switch diGital disPlay lock knob chuck table adjustment handle table base Fig. 10 FEATURES KNOW yOUR DRILL PRESS See Figure 2. Before attempting to use this product, familiarize yourself with all operating features and safety rules. FEED HANDLES MOTOR Feed handles raise and lower the chuck and bit during the drilling operation. Your drill press is equipped with an industrial duty induction motor for long-lasting, smooth performance. BEVEL SCALE CHUCK The bevel scale indicates the degree the table is tilted. Your drill press features a standard three-jaw type chuck with a self-ejecting chuck key, which prevents accidentally starting the drill press with the key still engaged in the chuck. SPINDLE LOCK LEVER SPINDLE SPEED TABLE The spindle lock lever secures the spindle at the desired depth for drilling. Five different spindle speeds allow you to drill a wide variety of material including wood, plastic, and metal. The table of your drill press rotates 360° and bevels up to 45° for angle drilling. DEPTH GAUGE DEPTH STOP A depth gauge is located between the pulley housing and feed handles to aid in drilling at desired depths. The adjustable locking depth stop permits accurate depth measurement and repetitive drilling. VARIABLE SPEED DIGITAL DISPLAy CHUCK TOOL Red numbers in the digital display show the RPM of the tool. The chuck tool is used to remove the chuck and chuck spindle. Adjust drilling speed using the variable speed lever on the side of the tool. Speed can only be changed when the tool is on. VISE Use the vise to secure the workpiece to the table when drilling. EXACTLINETM LASER WORKLIGHT The ExactlineTM laser makes accurate, precision drilling simple and easy. The integrated worklight can be used to help illuminate the work area. It requires a 15-watt, 10-volt, candelabra-base bulb (not included). TOOLS NEEDED The following tools (not included) are needed for assembly and alignment: adjustable wrench mallet or hammer PhilliPs screwdriVer Fig. 3 11 LOOSE PARTS The following items are included with the drill press: Head Assembly .................................................................1 Column Assembly .............................................................1 Table ..................................................................................1 Table Support ....................................................................1 Base ..................................................................................1 Hex Key (3 mm, 4 mm, and 5 mm)....................................3 Hex Bolts (M8) ...................................................................4 Feed Handles ....................................................................3 Worm Gear ........................................................................1 Spindle Lock Lever ............................................................1 Table Adjustment Handle ..................................................1 Table Lock Handle .............................................................1 Variable Speed Lever ........................................................1 Chuck Tool.........................................................................1 Chuck ................................................................................1 Chuck Key .........................................................................1 Vise ....................................................................................1 Operator's Manual (not shown) .........................................1 Variable sPeed leVer hex key (3) head assembly sPindle lock leVer chuck tool feed handles (3) sPindle table adjustment handle worm Gear chuck chuck key table table suPPort table lock handle hex bolts column assembly Vise base Fig. 4 1 ASSEMBLy UNPACKING This product requires assembly. Carefully remove the tool and any accessories from the box. Place it on a level work surface. NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and get help when needed. Inspect the tool carefully to make sure no breakage or damage occurred during shipping. Do not discard the packing material until you have carefully inspected the tool, identified all loose parts, and satisfactorily operated the tool. If any parts are damaged or missing, please call 1-800-55-579 for assistance. ATTACHING COLUMN ASSEMBLy TO BASE See Figure 5. Place the base on a flat surface. Align screw holes in the column assembly with screw holes in the base. Place a hex bolt in each hole and tighten using an adjustable wrench. WARNING: If any parts are damaged or missing do not operate this tool until the missing parts are replaced. Failure to heed this warning could result in possible serious personal injury. column assembly WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. hex bolt WARNING: Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury. base Fig. 5 13 ASSEMBLy INSTALLING TABLE ASSEMBLy See Figures 6 - 8. Loosen the set screw in the column collar. Remove the column collar and gear rack from the column and set aside. Locate the worm gear and feed the D-shaft through the hole in the table support. Install table adjustment handle over the end of the D-shaft so that the flat side of the shaft aligns with the set screw. Tighten the set screw using the hex key. Feed the gear rack through the slot in the table assembly so that the teeth are facing out and the longer smooth end faces up. The worm gear should engage the gear rack. Using both hands, slide the entire table assembly and gear rack onto the column until the bottom of the gear rack is positioned in the base collar and against the column. Slide the column collar, bevel-side down, over the column until the beveled side engages the beveled end of the gear rack. Tighten the set screw in the collar using the hex key. Do not overtighten. NOTE: You should be able to move the table from side to side. Locate the table lock handle. Insert it into the threaded hole at the rear of the table assembly and tighten by hand. d-shaft worm Gear Fig. 7 slot table suPPort table adjustment handle column collar table suPPort set screw set screw Gear rack base collar table suPPort table lock handle Fig. 6 threaded hole Fig. 8 14 ASSEMBLy INSTALLING CHUCK, HEAD ASSEMBLy, AND FEED HANDLES See Figures 9 - 11. NOTE: Move the table out of the way before beginning installation. Position the head assembly onto the column with the chuck positioned over the table. NOTE: The head assembly is heavy. Get help when needed. Slide the head assembly down as far as it will go. Align the head assembly with the base then tighten the two head set screws with the hex key. Attach the three feed handles by screwing them into the threaded holes in the hub. Position chuck on spindle. Chuck should be fully opened to avoid damaging jaws. Using a piece of scrap wood to protect the chuck, firmly tap the chuck into place using a mallet or hammer. the spindle into the spindle shaft turning it to the right Fit until it slips into place and tap with mallet using a piece of wood. hub feed handle Fig. 10 set screws head assembly head assembly sPindle Fig. 9 chuck Fig. 11 15 ASSEMBLy INSTALLING/CHANGING WORKLIGHT BULB See Figure 12. The integrated worklight can be used to help illuminate the work area. The worklight requires a 15-watt, 10-volt, candelabra-base bulb (not included). To install, insert the bulb into the worklight receptacle and twist clockwise to secure. MOUNTING THE DRILL PRESS See Figure 13. If the drill press is to be used in a permanent location, secure it to a workbench or other stable surface. If the drill press is to be used as a portable tool, fasten it permanently to a mounting board that can easily be clamped to a workbench or other stable surface. The mounting board should be of sufficient size to avoid tipping while drill press is in use. Any good grade plywood or chipboard with a 3/4 in. thickness is recommended. Mark holes on surface where drill press is to be mounted using holes in drill press base as a template for hole pattern. Drill holes through mounting surface. Place drill press on mounting surface, aligning holes in the base with holes drilled in the mounting surface. Insert bolts (not included) and tighten securely with lock washers and hex nuts (not included). If lag bolts are used, make sure they are long enough to go through holes in drill press base and material the drill press is being mounted to. If machine bolts are used, make sure bolts are long enough to go through holes in drill press, the material being mounted to, and the lock washers and hex nuts. NOTE: All bolts should be inserted from the top. Install the lock washers and hex nuts from the underside of the workbench. Once the drill press is securely mounted on a sturdy surface perform the following: Check for vibration when the motor is switched ON. Adjust and retighten the mounting hardware as necessary. Check the table assembly to assure smooth movement up and down the column. Check to assure that the spindle shaft moves smoothly. mountinG bolts bulb Fig. 1 base Fig. 13 16 ASSEMBLy INSTALLING/USING THE SPINDLE LOCK LEVER See Figure 14. The spindle lock is installed by aligning the threaded post on the lock lever with the hole on the left side of the tool then turning the post clockwise. Securely tightening the spindle lock lever locks the spindle in place. Turning the lock lever counterclockwise will loosen the spindle. CHECKING/ADJUSTING LASER ALIGNMENT See Figure 15. Check the laser alignment to ensure the intersection of the laser lines is precisely at the spot where the drill bit meets the workpiece. If it is not, the laser lines should be adjusted using the laser adjustment knobs located on opposite sides of the head assembly. Mark an "X" on a piece of scrap wood. Insert a small drill bit into the chuck and align its tip to the intersection of the lines of the "X". Secure the board to the table. Turn on the laser and verify the laser lines align with the "X" on the workpiece. the laser lines do not align, loosen the set screws on If each of the laser housings with a hex key and rotate the laser adjustment knobs until the lines meet in the center of the "X". Retighten the set screws to secure. laser housinG turn clockwise to install / lock the sPindle Fig. 14 WARNING: Use of controls or adjustments or performance of procedures other than those specified herein could result in hazardous radiation exposure. DANGER / DANGER / PELIGRO DANGER / DANGER / PELIGRO set screw laser adjustment knob Fig. 15 17 OPERATION WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING: Always remove the switch key when the tool is not in use and keep it in a safe place. In the event of a power failure, turn the switch OFF ( O ) and remove the key. This action will prevent the tool from accidentally starting when power returns. WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. WARNING: Always make sure the workpiece is not in contact with the bit before operating the switch to start the tool. Failure to heed this warning may cause the workpiece to be kicked back toward the operator and result in serious personal injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury. APPLICATIONS You may use this tool for the purposes listed below: Drilling in wood Drilling in ceramics, plastics, fiberglass, and laminates Drilling in metals POWER SWITCH See Figure 16. The drill press is equipped with a power switch that has a built-in locking feature. This feature is intended to prevent unauthorized and possible hazardous use by children and others. TO TURN THE DRILL PRESS ON: With the switch key inserted into the switch, lift the switch to turn ON (l ). TO TURN THE DRILL PRESS OFF: With the switch key inserted into the switch, push the switch down to turn OFF ( O ). TO LOCK THE DRILL PRESS: Place the switch in the OFF ( O ) position. Remove the switch key from the switch and store in a secure location. switch key remoVed Fig. 16 switch on switch off 18 OPERATION SELF-EJECTING CHUCK KEy See Figure 17. The self-ejecting chuck key ensures the chuck key is removed from the chuck before the drill press is turned on. In order to loosen or tighten the chuck using the chuck key, push the key into the key hole located on the chuck. Rotate the key clockwise to tighten the chuck or counterclockwise to loosen the chuck. chuck key WARNING: Use only the self-ejecting chuck key provided. Always remove chuck key. Failure to heed this warning could result in serious personal injury. key hole Fig. 17 table TABLE ROTATION See Figure 18. The table can be rotated out of the way when drilling large objects. Loosen the table lock handle. Rotate the table to the desired position. Retighten the table lock handle. table lock handle INSTALLING AND REMOVING BITS See Figure 19. Unplug the drill press. Open or close the chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Insert drill bit into the chuck the full length of the jaws. WARNING: Do not insert drill bit into chuck jaws and tighten as shown in figure 19. This could cause drill bit to be thrown from the drill press, resulting in possible serious personal injury or damage to the chuck. Tighten chuck jaws securely using chuck key provided. Do not use a wrench to tighten or loosen chuck jaws. Remove chuck key. remove the drill bit, reverse the steps listed above. To Fig. 18 wronG Fig. 19 19 OPERATION DRILLING See Figures 20 - 21. Using the vise provided (or similar clamping devices), secure the workpiece to the table. To protect the top surface of the workpiece, use a piece of scrap wood between the vise and the workpiece. Select the proper drill bit based on the hole size desired. For large holes, drill a pilot hole first, using a smaller diameter bit. Unlock the spindle lock lever and the lock knob. Using the feed handles, set the spindle at the desired depth and retighten both the lock lever and lock knob securely. Turning the table adjustment handle, set the table to desired height. NOTE: Make sure the table is free of all loose objects and the bit is not in contact with the workpiece. Plug the electrical cord into power supply and turn the switch ON. Make sure spindle rotates freely. ith the motor running, change the spindle speed with W the variable speed lever. NOTE: The digital display on the front of the drill press will give you the exact spindle speed. Use the chart below to determine speed for the material and drill size. Slowly lower drill bit into workpiece. Do not force the bit; let the drill press do the work. Once the hole is completed, allow the spindle to return to its normal position. This will automatically raise the chuck and bit. DRILLING TIPS a large hole is needed, it's a good idea to drill a smaller If pilot hole before drilling the final one. Your hole will be more accurately positioned, rounder, and the bits will last longer. the hole is deeper than it is wide, back off occasionally If to clear the chips. When drilling metal, lubricate the bit with oil to improve drilling action and increase bit life. you increase the bit size, you may need to reduce the As spindle speed. drilling a through hole, make sure that the bit will not If drill into the table after moving through the workpiece. Vise hex bolt Variable sPeed leVer Fig. 1 Fig. 0 0