User manual RYOBI EMT0005

EMT0005 ELECTRONIC MeasureTechTM EMT0005 ELECTRONIC MeasureTechTM DISPLAY The Ryobi Electronic MeasureTechTM is intended for a fast, convenient distance measure, or with a laser pointer which shows exactly the location where the measurement will be taken. It features a sleek, high-impact case. For damage caused by usage other than intended, the user is responsible. SQUARE CUBIC FEET METER 2 ft. min. CAUTIONS · Do not expose the unit to direct sunlight, high temperature, high humidity, excess dust, or mechanical shock. · When the unit is not to be used for a long period, remove the battery to avoid damage from possible battery leakage. · It is a household product. · Not for repair, open only by authorized persons. SPECIFICATIONS · Class II Laser Module 650 mm. · Measurement Range 2' to 50' (0.6 m to 15 m) · Accuracy: + 0.5% + 1 Digit (*) · Resolution: 1' (0.01 m) · Apeture angle: Approx. + 5 Degrees · Calculation Range: Length - 999'11" (999.99 m) Area - 99999 Sq.ft (999.9 SQ M) Volume - 99999 Cb. ft (9999.9 CB M) · Power Consumption: Approx. 0.4 W Average · Display: 5 Digits Liquid Crystal Display · Battery: 9 Volt · Size: 4.84"X2.36"X1.54": (123 mm X 60 mm X 39 mm) · Weight (Without Battery): Approx. 3.14 oz(88g) (*)For measuring long distance from 40 ft to 50 ft (2m to 15m), the relative humidity should be 50% or above and target size should be at least 10 ft. by 10 ft (3m by 3m). MULTIPLY X sq. cu. ft. m. REFERENCE (TOP) ft 2' 0" SET x/= READ VERIFYING IF THE UNIT WORKS · After battery is installed,press the "READ" button. If numbers appear on the LCD display, then the unit is working properly. LOW BATTERY INDICATOR REFERENCE (BOTTOM) OPERATING ENVIRONMENT · Temperature 32°F to 104°F (0° to 40°). · Still Air · Hard Surface FEATURES · Instant measurement · Dynamic measurement capability of 50 feet (15 meters) · Selective measurement reference: top or bottom of the case · Computation of area and volume · 5 digit LCD for easy read screen · Built in laser pointer · Conversion ft-in to metric PARTS IDENTIFICATION KEYBOARD 1. SET - Select measurement reference 2. READ - Read distance 3. X / = - Multiply / equal RYOBI TECHNOLOGIES INC. 1428 Pearman Dairy Road Anderson, SC 29625 www.ryobitools.com 1-800-525-2579 HINTS · Any large obstacle found within + 5° for the viewing angle of the unit might be regarded as the target. · Large, flat, hard surfaces usually give more accurate results. · To measure small, irregular or soft objects, place a piece of cardboard in front of the object. · Change of measurement base does not affect old readings. · The unit cannot measure through glass. OTHERS 4. Laser aperture 5. Display 6. Measurement reference - top 7. Measurement reference - bottom 8. Battery compartment ( back ) MEASUREMENT REFERENCE · Press "SET" button to select measurement base: top or bottom of case. · To change from feet to meters, or vice versa, press the "set" and "X/=" button simultaneously. Situations Inaccurate readings of distance Possible Causes · Battery runs out of power · Measured distance is < 2' or > 50' (< 0.6m or > 15m). · Another ultrasonic source is nearby · Measured distance is < 2' or > 50' (< 0.6m or > 15m). The target is not a good ultrasonic reflector. (e.g. thick carpet, irregular wallpaper, etc.). · The unit points to the target obliquely. · Computation is out of the specified range. Solutions · Replace new battery · Make sure measured distance is within range · Remove the ultrasonic source and try again. ERROR DISPLAY · · · · The unit will give inaccurate readings if: The battery runs out of power The distance to be measured is less than 2' (0.6m) or There is another ultrasonic source in the vicinity. "ERROR" will be displayed if the reflected ultrasonic pulses are not strong enough. This may happen when: -The measuring distance is out of working range. -The target is not a good ultrasonic reflector (e.g. thick carpet, irregular wall paper, etc.) -The unit of the multiplication result is higher than cube. Class II Laser Product Max. Power Output < 1mw Wavelength: 640-670 nm Complies with CFR 21 parts 1040.10 and 1040.11 USE AS INTENDED: The MeasureTechTM is intended for a fast, convenient distance measurement with a laser pointer which shows exactly where the measurement is being taken. 4 6 NOTE: The MeasureTechTM measurement unit is defaulted in ft-in. CAUTION Avoid direct exposure to the beam. Read instructions in manual. MEASUREMENT PROCEDURES · Select the measurement reference. · Point the unit perpendicular to the target. The laser will show where the estimator is pointed and is on only while a reading is being taken. Caution: Do not stare into Laser beam. Hold unit with beam above or below eye level. · Press the "READ" button to take the measurement. · Hold the "READ" button for continuous measurement. LCD displays "Error" · Make sure mearured distance is within range. · Place a piece of cardboard in front of target. · Make sure computation is within range. WARRANTY This product is a consumable item. Therefore it is warranted against defective parts and labor only and not misuse or deterioration of product through normal wear and tear for a period of 2 years from date of purchase. ft 2' 0" SET x/= 5 INSTALLING THE BATTERY · Slide back of unit off to replace battery. · Snap 9-V battery into compartment, terminal side first, matching (+) and (-) terminals from battery to case. · Replace the back by sliding into grooves. Alkaline battery life is approximately 7000 measurements. · The battery should be replaced when battery indicator is on. WARNING: To avoid risk of eye injury, do not stare directly into beam. Never point the beam into anyone's eyes. Do not permit children to use this device. It is not a toy. 3 READ 983000-284 6-03 1 2 8 Finding square footage/meters and cubic footage meters · After taking initial measurement, press the "X/=" key. Take the second measurement and again press the "X/='' key. LCD display will show "SQ.M". Take a third measurement and again press "X/=" key. LCD display will show "cu.ft". or "cu.m". 7