User manual SAGEM AXIUM HD-L32

Dear SAGEM Customer, Congratulations and thank you for choosing the SAGEM AXIUMTM High Definition LCD TV. This product was manufactured with the greatest care and attention and we hope you will enjoy the spectacular viewing experience for many years. This product is very diverse and we recommend that you first refer to the Quick Start Guide on page 4. We recommend you to keep this document in a safe place in order to be able to refer to it afterwards. This product is European compliant. If you should incur any potential problem which is not covered in Troubleshooting and Support on page 70, please contact your retailer or distributor where applicable. © 2005 SAGEM COMMUNICATION SA. All rights reservedThis document is the property of SAGEM COMMUNICATION SA. Reproduction without written permission from SAGEM COMMUNICATION SA is strictly forbidden. The information contained in this document may be changed without prior warning. The brands quoted in this operating manual, SAGEM logo and SAGEM, are SAGEM COMMUNICATION SA registered trademarks. Virtual Dolby Surround `Manufactured under license from Dolby Laboratories. `Dolby', `Pro Logic' and the double-D symbol are trademarks of Dolby Laboratories.' The `HD ready' Logo is a trademark of EICTA. Documentation content can be subject to amendment. LCD Television 32" SAGEM AXIUMTM HD-L32 SAGEM AXIUMTM HD-L32 T IMPORTANT: Please read this guide thoroughly before using your unit. Veuillez lire attentivement ce manuel avant d'utiliser votre téléviseur. Lesen Sie bitte dieses Handbuch sorgfältig vor der Inbetriebnahme Ihres Gerätes. ENVIRONMENT Preservation of the environment as part of a sustainable development logic is an essential concern of SAGEM SA. The desire of SAGEM SA is to operate systems observing the environment and consequently it has decided to integrate environmental performances in the life cycle of its products, from manufacturing to commissioning, use and elimination. PACKAGING The presence of the logo (green circle) means that a contribution is paid to an approved national organization to improve packaging recovery and recycling infrastructures. To faciliate recycling, respect the sorting rules set up locally for this kind of waste. THE PRODUCT The crossed-out waste bin stuck on the product means that the product belongs to the family of electrical and electronic equipment. USER GUIDE In this respect, the European regulations ask you to dispose of it selectively: At sales points in the event of the purchase of similar equipment. At the collection points made available to you locally (drop-off center, selective collection, etc.). In this way you can participate in the re-use and upgrading of Electrical and Electronic Equipment Waste, which can have an effect on the environment and human health. ENGLISH SAFETY PRECAUTIONS High Voltage This LCD TV is a class 1 appliance; it MUST be connected to an electrical wall socket equipped with an earth. This LCD TV is designed to function: with a 100-240 V, 50-60 Hz, AC (alternating current) network, at an ambient temperature between +5 deg C and +35 deg C, in areas with humidity less than 85%. This LCD TV uses high voltages. Never attempt to access the interior of the device. Only suitably qualified persons are authorised to do this. Do not open or dismantle this product, as this will expose you to risk of electrocution. Damage Weather Moisture Never use your TV if it is damaged in any way. Always place your TV on a flat level surface avoiding anywhere which may be subject to strong vibration. It is advisable to unplug the aerial during an electrical storm. Do not allow your TV to be exposed to rain, moisture, dust. If any liquid is spilt into your TV it can cause serious damage. If you spill any liquid into your TV switch it off at the mains immediately. Contact your store. Do not place your TV on or near appliances which may cause electromagnetic interference (TV or Hi-Fi speakers). If you do, it may adversely affect the working of the unit, and cause a distorted picture or sound. Avoid extremes of temperature, either hot or cold, place your TV well away from heat sources such as radiators or gas/electric fires. The TV must be well ventilated. Do not cover your TV or position in a small confined space. It is recommended that you leave a gap all around your TV. Batteries Batteries are easily swallowed by young children. Do not allow young children to play with the remote control unit. Only use suitable batteries that comply with the maker's specifications (see 4-2 Inserting Batteries into the Remote Control). The batteries supplied are not rechargeable; Pay particular attention to environmental matters; Take the defective or used batteries to places provided for this effect in accordance with current regulations; never throw them in the dustbin. Covers Standby Screen Burn Do not remove any fixed covers as this may expose dangerous high voltages. Do not leave your TV in standby for long periods of time e.g. while on holiday. ATTENTION! Please note that some programmes are broadcast with a logo that will appear in the corner of your TV screen. Some of these logo's can be very bright and may cause damage by permanently marking the logo on the screen. To prevent this, avoid leaving channels displaying a logo for prolonged periods of time, particularly when the TV is not being watched. Interference Temperature Ventilation 2 3 ENGLISH Quick Start Guide QUICK START GUIDE Display Stand Installation The display stand may not be already assembled when you receive your unit. If it is not, follow the procedure below to install it to your unit before you continue. 1. Remove the protective cover and hinge cover on the back of your LCD TV. 4. Attach the display stand to the back of your LCD TV with two (2) M8*30 capscrews using a hexagon key to tighten the capscrews. 4 Glass Display Stand Back Protective Cover Back of LCD TV 5. Fasten the hinge cover with the three (3) M8*30 capscrews that were removed in Step 1 using the provided hexagon key. 6. Fasten the back protective cover that was removed in Step 1. LCD TV with Display Stand Attached 2. Remove the hinge cover on the back of your LCD TV. Back of TV with Protective Cover and Hinge Cover Removed Hinge Cover Hinge Cover 5 Back Protective Cover 6 3. Fasten the two (2) M8*100 capscrews with washers to the bottom of the glass display stand using the provided hexagon key. NOTE: The washers are necessary to prevent damage to the glass when fastening the capscrews. 3 4 5 ENGLISH Quick Start Guide Quick Start Guide Connection Diagrams Getting Started 1. Basic Connection for Analog TV Unpack your LCD TV. LCD TV Remote control Two (2) AA alkaline batteries 6-in-1 CF adaptor* Power cord RF (aerial) lead This user's guide Display stand Five (5) M8*30 capscrews Two (2) M8*100 capscrews Two (2) washers for M8*100 capscrews Hexagon key 3 4 8 9 2. 3. 4. Basic Connection for Digital TV (DTV)* and AV Disconnect power to all your existing equipment. Locate unit in preferred position. Connect all equipment as shown in the diagram on the adjacent page. Once all other connections are made, connect power and switch on your unit. 5. Remote Control Modes RF LOOP THROUGH CABLE The remote control must be in the same mode (analog or digital*) as the LCD TV in order for it to work properly. The Power/Status LED at the front of the unit indicates the current mode of your unit (see 2-1 Front Panel Controls for the different modes and the corresponding LED indicator color). When the remote control is in analog mode, the TV button on your remote control will light up in green each time a button on the remote control is pressed. When the remote control is in digital mode*, the DTV button on your remote control will light up in yellow each time a button on the remote control is pressed. LCD TV POWER LED GREEN AMBER REMOTE CONTROL GREEN TV BUTTON YELLOW DTV BUTTON MODE ANALOG TV DIGITAL TV* 6 * Available only with SAGEM AXIUM HD-L32 T. * Available only with SAGEM AXIUM HD-L32 T. 7 ENGLISH Quick Start Guide Quick Start Guide Connecting Your TV 1. 2. 3. 4. 5. Connect an aerial antenna (see Basic Connection diagram on the adjacent page). Insert batteries into the remote control (see 4-2 Inserting Batteries into the Remote Control for more details). Connect the power cord to the power cord connector on the back of your LCD TV (see Basic Connection diagram on the adjacent page). Press the Main Power switch next to the power cord connector on the LCD TV. Press the POWER button on your remote control. Switching to Digital TV* This LCD TV features an integrated digital TV tuner designed to receive digital broadcast. To switch to digital TV, press the DTV button. ENGLISH NOTE: When set to digital TV, the DTV button will light up in yellow each time you use your remote control. When set to analog TV, the TV button will light up in green each time you use your remote control. First Time Use The first time you use your TV in DTV mode, you will have to perform a "First Installation procedure". NOTE: The OK button always confirms a selection within these menus, and pressing it will take you to the next step in the installation process. However, and this is important, often more than one value has to be entered in a menu. First, perform all necessary settings on the different lines. Then confirm them all simultaneously by pressing OK. Use to move upwards and downwards from one line to another. Setting Up Analog TV To change the language of the OSD menus 1. 2. 3. 4. 5. 6. Press the TV MENU button on your remote control to access the Main Menu. Use to highlight Options. Press OK, and the Options Menu opens. Use Use to highlight Language. to select the desired language. Use to change settings. You can also use the numerical keys on the remote control to enter numeric values. Press the EXIT button on your remote control to close the OSD. To tune channels automatically To quickly add all channels that have signals to your channel list, refer to 7-1 Tuning Channels Automatically for detailed instructions. 8 * Available only with SAGEM AXIUM HD-L32 T. 9 Quick Start Guide 1. Press the DTV button to switch to digital TV. 2. Press OK on your remote control to continue. The Menu Language menu opens. 3. Select the desired language with OK. and press SAFETY PRECAUTIONS ..........................................................................................2 QUICK START GUIDE ...............................................................................................4 Display Stand Installation .......................................................................................4 Connection Diagrams ............................................................................................6 Getting Started ......................................................................................................7 Remote Control Modes ..........................................................................................7 Connecting Your TV ...............................................................................................8 Setting Up Analog TV ............................................................................................8 Switching to Digital TV* ..........................................................................................9 First Time Use .......................................................................................................9 1 BEFORE YOU START ....................................................................................... 13 1-1 What's in the Box ........................................................................................ 13 1-2 Optional Accessories ...................................................................................14 2 YOUR LCD TV AT A GLANCE ...........................................................................15 2-1 Front Panel Controls .................................................................................... 15 2-2 Back Connectors ......................................................................................... 16 3 YOUR REMOTE CONTROL AT A GLANCE ...................................................... 18 4 BASIC LCD TV SETUP ..................................................................................... 21 4-1 Connecting an Aerial Antenna ...................................................................... 21 4-2 Inserting Batteries into the Remote Control .................................................. 22 4-3 Using the Remote Control (Basic Operation) ................................................22 4-4 Plugging In Your LCD TV .............................................................................. 23 4-5 Turning ON the Power ..................................................................................24 Contents ENGLISH and press 4. Select the desired country with OK. This will also set the current time. 5. The search procedure begins for digital TV and radio channels. NOTE: The search procedure may take a few minutes, so be patient. Cancel at any time by pressing EXIT. When the search procedure has ended, a message will indicate how many digital TV and radio channels have been found. 6. If the channel has found no channel, this screen is displayed to help you adjust the aerial. Enter a channel number (refer to http// www.dtg.org.uk/retailer/tx_details/_tx_index.htm. For example, Oxford channel numbers are 29, 34, 48, 51, 52, 68. These numbers depend on broadcasters and are subject to change.) and move the antenna until the signal and quality bars are green. When signal and quality are green, press to launch a new channel search. 10 * Available only with SAGEM AXIUM HD-L32 T. 11 5 CONNECTING EXTERNAL DEVICES .............................................................. 25 5-1 Connecting an HDMI Device ........................................................................26 5-2 Connecting a Component Device ................................................................27 5-3 Connecting a VCR Using Coaxial (RF) ........................................................28 5-4 Connecting a SCART Device....................................................................... 29 5-5 Connecting a Computer (VGA) .................................................................... 30 6 ADJUSTING TV SETTINGS .............................................................................. 35 6-1 Basic Operations ......................................................................................... 35 6-2 Using the TV On-screen Display (TV OSD) .................................................. 37 6-3 OSD Menus and Options ............................................................................. 38 6-4 Adjusting Picture Settings ............................................................................ 44 7 TUNING YOUR ANALOG TV ............................................................................. 45 7-1 Tuning Channels Automatically (AUTO SEARCH) ......................................... 45 7-2 Tuning Channels Manually (MANUAL SEARCH) ........................................... 46 7-3 Sorting Channels (PROGRAMME SORT) ................................................... 47 7-4 Removing Unwanted Channels (MANUAL SEARCH) ................................... 48 8 ADVANCED SETTINGS AND FUNCTIONS ...................................................... 49 8-1 Setting the Sleep Timer ............................................................................... 49 8-2 Setting Parental Control ............................................................................... 50 8-3 Setting a Password ...................................................................................... 51 8-4 Displaying Teletext ....................................................................................... 52 8-5 Dual Picture Modes ..................................................................................... 53 8-6 Multi-channel View Mode ............................................................................. 56 8-7 Picture Formats ...........................................................................................56 9 DIGITAL TV (DTV)* ............................................................................................57 9-1 Advanced Digital TV Settings ....................................................................... 57 9-2 Using Digital TV ...........................................................................................62 9-5 Digital TV Software Upgrade ....................................................................... 69 TROUBLESHOOTING AND SUPPORT .................................................................70 PRODUCT SPECIFICATIONS ................................................................................ 73 1 1-1 BEFORE YOU START What's in the Box When you receive your LCD TV, unpack it carefully, and check to make sure you have all the items below. 1 REMOTE CONTROL AND TWO AA BATTERIES 2 POWER CORD 3 RF CABLE 3 4 8 9 4 DISPLAY STAND 5 FIVE M8*30 CAPSCREWS 6 TWO M8*100 CAPSCREWS 7 TWO WASHERS 8 HEXAGON KEY 9 10 USER GUIDE 12 * Available only with SAGEM AXIUM HD-L32 T. * Available only with SAGEM AXIUM HD-L32 T. 13 ENGLISH Chapter 1 Before You Start 1-2 Optional Accessories The following are optional accessories you may purchase for your LCD TV: CABLE KITS RCA audio cable SCART lead/cable S-video video cable Composite video cable - RCA to RCA Component (YUV) video cable - 3 RCA to 3 RCA WALL MOUNT KIT The SAGEM wall mount kit, which is sold separately, contains all of the required hardware for mounting your LCD TV on your wall. It is highly recommended that you find a qualified installer to do this. VGA video cable HDMI video cable 2 2-1 YOUR LCD TV AT A GLANCE Front Panel Controls 1 2 3 4 5 6 REMOTE CONTROL SENSOR 7 BUTTON 1 VIEWING FUNCTION (OSD OFF) MENU FUNCTION (OSD ON) Displays the next stored channel. Selects the next menu option. N/A when the video source is set to DTV*. Displays the previous stored channel. Selects the previous menu option. N/A when the video source is set to DTV*. Increases the sound level. Displays a submenu with selections for the current menu option. Increases a menu option value. 2 3 4 5 Lowers the sound level. Selects the next input source. Activates the OSD main menu. Turns the LCD TV ON/OFF. Reduces a menu option value. Selects the next input source. Returns to the previous menu or exits OSD menus. Turns the LCD TV OFF. 6 7 14 * Available only with SAGEM AXIUM HD-L32 T. 15 ENGLISH Chapter 2 Your LCD TV At A Glance Chapter 2 Your LCD TV At A Glance 2-2 Back Connectors 2-3 Right-side Connectors 1 1 2 3 4 56 7 8 9 10 11 12 CONNECTOR DESCRIPTION Main power switch - Turns the main power ON and OFF. Power cord connector - Connect the power cable to this. HDMI - Connect a Consumer Electronics device, such as a DVD player or HDTV STB, to this. NOTE: This connector can also accept DVI signal with a DVI-to-HDMI adaptor. VGA - Connects to a computer's VGA terminal output. Audio In - Connects to a computer's audio out jack. HiFi Out - Connects to your audio amplifier device. SCART - Connect a decoder, DVD player, or satellite box to this connector (RGB, S-Video, or Composite). SCART - Connect a decoder, DVD player, or satellite box to this connector (RGB, S-Video, or Composite). TUNER (UHF/VHF-CATV) - Connect to antenna or analog cable service. YUV - Connect a component (YPbPr) device, such as a DVD player, to these connectors. DTV loop through* - Feeds both analog and digital TV signals to the TV's tuner and enables independent recording of both analog and digital channels. DTV Antenna In* - Connects to digital broadcast. 2 3 4 5 6 1 2 3 CONNECTOR DESCRIPTION Memory card reader* - Supports Type I/II CompactFlash cards.For other compatible cards, please use the 6-in-1 adapter provided. AV3 (S-Video In) - Connect an S-Video device to this. AV3 (Composite Video In) - Connect a composite audio/video device, such as a camcorder or digital camera, to this connector. Audio In (Left) - Connect the white (L) audio RCA from a composite or S-video device to this connector. Audio In (Right) - Connect the red (R) audio RCA from a composite or S-video device to this connector. Headphone jack - Connect a headphone to this stereo headphone jack. Using this jack automatically disables the built-in speakers. 4 5 1 2 6 7 3 4 5 6 8 9 10 11 12 16 * Available only with SAGEM AXIUM HD-L32 T. 17 ENGLISH Chapter 3 Your Remote Control At A Glance 3 YOUR REMOTE CONTROL AT A GLANCE 1 2 3 BUTTON POWER DTV* TV AV PC FORMAT VIDEO MODE GUIDE* BACKLIGHT UP LEFT RIGHT DOWN OK BACK EXIT VOL+/VOLPR+/PRMUTE INFO STILL NUMBER PAD DTV MENU* DESCRIPTION (TV MODE) Turns the power ON/OFF. Switches to DTV mode (Digital TV). Switches to TV mode (Analog TV). Changes the input source to AV1, AV2, or AV3. Changes the input source to YUV, HDMI, or VGA. Selects the picture format (4:3, 14:9, 16:9, Zoom, Panorama) that best meets your viewing requirement. Sets the video mode. Options are User, Soft, Normal, Strong, and Intense. Displays the channel guide when in DTV mode. Adjusts the backlight brightness level. Navigates up in the on-screen display (OSD) menus. Navigates left in the on-screen display (OSD) menus. Navigates right in the on-screen display (OSD) menus. Navigates down in the on-screen display (OSD) menus. Works as the ENTER button. Confirms selection. Displays the channel list in DTV* mode. Toggles between the last viewed channel and the current channel. Exits from the on-screen display (OSD). Increases/decreases the volume. Changes the channel. Mutes or restores the sound volume. Shows information about the current input source. Freezes the displayed image. Selects a channel or enters a number. Activates the DTV* OSD menu. 1 2 4 10 11 13 15 19 20 21 23 3 4 8 9 4 3 5 14 12 16 PR 5 6 7 8 6 9 7 8 9 10 17 18 11 12 13 22 24 25 26 27 28 14 15 36 37 38 39 32 33 34 35 29 30 31 40 41 42 16 17 18 19 20 21 22 23 18 * Available only with SAGEM AXIUM HD-L32 T. 19 ENGLISH Chapter 3 Your Remote Control At A Glance BUTTON DESCRIPTION (cont'd) Activates the TV OSD menu. Activates Teletext RED functions. 4 4-1 BASIC LCD TV SETUP Connecting an Aerial Antenna Connect the outdoor aerial (antenna) cable lead-in to the TUNER (UHF/VHF-CATV) jack on the back of your LCD TV using the supplied RF (coaxial) lead. See 2-2 Back Connectors for location. 24 25 26 27 28 29 30 TV MENU RED GREEN YELLOW BLUE AUDIO AUDIO ENH RADIO* FUNCTION TELETEXT SUBTITLES* LIST* + 25 + 26 + 27 Activates Teletext YELLOW functions. Activates Teletext BLUE functions. Changes the audio mode. Options are STANDARD, SPATIAL, VIRTUAL DOLBY SURROUND, and ENHANCED SPATIAL. Available in DTV mode only. Switches to Radio mode. Press to activate functions such as PIP that are marked in blue. Toggles ON/OFF Teletext mode. Activates subtitles in DTV mode. Changes the favorite list when in DTV mode. MOSAIC - Activates Multi Channel View mode (only available in Analog Mode). PIP, PAP, Full Screen - Selects PIP mode. PIP SEL - Changes sub source (TV/AV1/AV2/AV3) when the main source is set to YUV, HDMI, or VGA, or vice versa. PIP SWAP - Swaps the main and sub pictures. Teletext Index (only in Teletext mode) Teletext List (only in Teletext mode) Teletext Reveal (only in Teletext mode) 31 32 33 34 35 36 37 38 39 40 41 42 + 28 + 29 + 30 + 31 20 * Available only with SAGEM AXIUM HD-L32 T. 21 ENGLISH Activates Teletext GREEN functions. Chapter 4 Basic LCD TV Setup Chapter 4 Basic LCD TV Setup 4-2 Inserting Batteries into the Remote Control Before using the remote control for the first time, insert two AA batteries (supplied). When the batteries become depleted and the remote control fails to operate, replace the batteries with new batteries. TO INSERT BATTERIES 1. Remove the battery cover on the back of the remote control. 2. Insert two AA batteries into the remote control. Make sure that you match the + and -on the batteries with the + and - symbols inside the battery compartment. 3. Close the battery cover by aligning it with the base of the remote control and sliding it back into place. NOTE: Always recycle used batteries in accordance with local regulations. Contact your local recyling center for proper disposal information. The batteries supplied are not rechargeable. Pay particular attention to environmental matters. Take the defective or used batteries to places provided for this effect in accordance with current regulations; never throw them in the dustbin. 4-4 Plugging In Your LCD TV 1. Connect the power cord to the power cord connector on the back of your LCD TV (see 2-2 Back Connectors). ENGLISH 2. Plug the other end of the power cord into a properly grounded electrical outlet or surge protector. 4-3 Using the Remote Control (Basic Operation) Point the remote control towards the remote control sensor window located on the front of your LCD TV. Make sure no objects are in the line of aim, otherwise the remote control may not operate properly. 22 23 Chapter 4 Basic LCD TV Setup 4-5 Turning ON the Power 1. Press the Main Power switch next to the power cord connector on the LCD TV. The Status LED on the front turns red and your LCD TV is ready to turn on. 2. Press the POWER button on the right side of your LCD TV or on your remote control. The Status LED on the front turns green, and the unit turns on. NOTE: When in analog TV mode, the power LED at the front of your unit will be green. When in digital TV* mode, the power LED at the front of your unit will be amber. 5 CONNECTING EXTERNAL DEVICES Read this section to learn how to connect the following devices: DVD players DTV or HDTV set-top boxes VCRs Computers Game players WARNING! Before connecting any external components, make sure to unplug your LCD TV and any connecting devices to prevent damage. ENGLISH 24 * Available only with SAGEM AXIUM HD-L32 T. 25 Chapter 5 Connecting External Devices Chapter 5 Connecting External Devices 5-1 Connecting an HDMI Device 1. Connect one end of an HDMI cable (not supplied) to your device and the other to the HDMI connector on the back of your LCD TV. See 2-2 Back Connectors for location. 2. Turn on your LCD TV (see 4-5 Turning ON the Power), then press the PC button on your remote control repeatedly to select HDMI. 5-2 Connecting a Component Device 1. Connect the green-colored Y RCA jack on the back of your device to the green-colored Y RCA jack on the back of your LCD TV. ENGLISH 2. Connect the red-colored Pr RCA jack on the back of your device to the red-colored Pr RCA jack on the back of your LCD TV. 3. Connect the blue-colored Pb RCA jack on the back of your device to the blue-colored Pb RCA jack on the back of your LCD TV. 4. Connect the red (R) and white (L) audio RCA jacks on the back of your device to the YUV R and L audio-in RCA jacks on the back of your LCD TV. 5. Turn on your LCD TV, then press the PC button repeatedly to select YUV. NOTE: To connect a DVI device, use a DVI-to-HDMI adaptor. You will also have to connect the audio cable from your DVI device to the PC Audio In connector. 26 27 Chapter 5 Connecting External Devices Chapter 5 Connecting External Devices 5-3 Connecting a VCR Using Coaxial (RF) 5-4 Connecting a SCART Device 1. Connect one end of a 21-pin Euro-SCART lead (not supplied) to your device and the other to the SCART connector on the back of your LCD TV. See 2-2 Back Connectors for location. 2. Turn on your LCD TV (see 4-5 Turning ON the Power), then press the AV button repeatedly to select either AV1 or AV2, depending on to which connector your SCART device is connected. NOTES: The picture format (16:9) is automatically detected by your unit. ENGLISH 5-3-1 Video Recorder without Decoder To record digital programmes from your LCD TV, the VCR must be connected to a SCART connector. NOTE: If your VCR does not have a SCART connector, the only connection possible is via the aerial cable. You will therefore need to tune in your video recorder's test signal and assign it to a program number. In this case, it will not be possible to record digital channels. 5-3-2 Video Recorder with Decoder Connect the decoder to the second SCART connector on your video recorder. You will then be able to record scrambled transmissions. WARNING! If an outdoor antenna or cable system is connected to your LCD TV, make sure that the antenna or cable system is correctly grounded. AV1 ANTENNA RF lead (supplied) SCART lead (optional accessory) VCR SCART lead (optional accessory) DECODER SCART Devices 28 29 Chapter 5 Connecting External Devices Chapter 5 Connecting External Devices 5-5 Connecting a Computer (VGA) 1. Connect the VGA connector on your computer to the VGA connector on the back of your LCD TV with a VGA monitor cable. 2. Connect the Audio Out jack on your computer to the Audio In jack on the back of your LCD TV. 3. Turn on your LCD TV (see 4-5 Turning ON the Power), then press the PC button on your remote control to select VGA as your input source. 5-6 Connecting an Audio Amplifier Device Connect an audio amplifier device to the HiFi Out jack on the back of your LCD TV. 3.5mm 30 31 ENGLISH Chapter 5 Connecting External Devices Chapter 5 Connecting External Devices 5-7 Connecting a Composite Device 1. Connect the yellow video RCA from your VCR, camcorder, or digital camera to the yellow AV3 videoRCA connector on the right-side of your LCD TV with an RCA cable (not supplied). 2. Connect the red (R) and white (L) audio jacks from your VCR, camcorder, or digital camera to the appropriately numbered AV3 R and L audio-in jacks on the right-side of your LCD TV. 3. Turn on your LCD TV (see 4-5 Turning ON the Power), then press the AV button on your remote control repeatedly to select AV3. 5-8 Connecting an S-Video Device 1. Connect the S-Video mini-DIN connector on the back of your S-Video device to the SVIDEO connector on the right-side of your LCD TV with the correct optional cable. ENGLISH 2. Connect the red (R) and white (L) audio RCA jacks on the back of your S-Video device to the R and L audio-in RCA jacks on the right-side of your LCD TV. 3. Turn on your LCD TV (see 4-5 Turning ON the Power), then press the AV button on your remote control repeatedly to select AV3. 32 33 Chapter 5 Connecting External Devices 5-9 Connecting a Headphone Connect a headphone to the Line Out jack on the right-side of your LCD TV. 6 6-1 ADJUSTING TV SETTINGS Basic Operations 6-1-1 Adjusting the Volume You can adjust the volume in two ways - from your LCD TV's right side panel or by using the remote control. TO ADJUST VOLUME FROM THE RIGHT SIDE PANEL Press 3.5mm to increase/decrease the sound level. 1 2 3 4 NOTE: When a headphone is connected, the TV's internal speakers are turned OFF. 5 6 7 34 35 ENGLISH Chapter 6 Adjusting Settings Chapter 6 Adjusting Settings TO ADJUST VOLUME FROM THE REMOTE Press (see illustration for location) to turn up or turn down the volume. 6-2 Using the TV On-screen Display (TV OSD) TO TEMPORARILY TURN OFF VOLUME (MUTE) Press the MUTE button on the remote control. PR 6-2-1 Making Adjustments You can access the OSD from either the right side of your LCD TV display or from your remote control. 1. With the power ON, press the TV button. 2. Press TV MENU to access the Main Menu. In DTV* mode, press DTV MENU to set DTV* parameters. NOTE: When you press the TV MENU button on your remote control, the remote control switches automatically to TV mode. 1 4 5 6 PR TO TURN VOLUME BACK ON Press the MUTE button again or press . 3 4 8 9 1 3 6 3 6-1-2 Selecting Channels TO SELECT CHANNELS FROM THE LCD TV Press to select channels. 3. Press options. to select one of the menu 2 4 8 9 2 4. Press OK on your remote control to access the submenu. 5. Press to make adjustments. TO SELECT CHANNELS FROM THE REMOTE Press PR 6. Press the BACK button to return to the previous menu option. PR - OR Press the EXIT button to close the OSD. (see illustration for location) or use the number pad to input the 4 3 channel number.. 36 * Available only with SAGEM AXIUM HD-L32 T. 37 ENGLISH Your LCD TV features an on-screen display (OSD) that lets you adjust and save contrast, brightness, and other settings. All the function settings are accessible either through the proper control buttons on the right side of your LCD TV or through the remote control. OSD menus may be different depending on the current input source. Chapter 6 Adjusting Settings Chapter 6 Adjusting Settings 6-3 OSD Menus and Options You can use these OSD menus and options to adjust various settings for your LCD TV. Sound Menu To access the Sound Menu, highlight Sound from the Main Menu and press OK. Sound Menu Balance Bass Trebble Loudness Sound Effect Normal Standard 0 0 0 6-3-1 With Source Input Set to TV Main Menu Balance - Adjusts the level of sounds between the left and right speakers. Bass - Adjusts the bass value to enhance the low frequency sounds. Treble - Adjusts the treble value to enhance high frequency sounds. Loudness - Sets the sound intensity. ENGLISH Move Setting Return BACK Sound Effect - Select Standard, Spatial, Virtual Dolby Surround, or Enhanced Spatial. Setup Menu To access the Setup Menu, highlight Setup from the Main Menu and press OK. Auto Search - Select this option allows you to automatically search for all analog programmes that are available in your region. Manual Search - Select this option allows you to store analog programmes one at a time. Programme Sort - Select this option to rearrange the channel list and remove channels from the channel list. Picture Menu To access the Picture Menu, highlight Picture from the Main Menu and press OK. Picture Menu Brightness Contrast Colour Sharpness Image+ Colour Temp. 30 25 30 30 Normal Natural Setup Menu Auto Search Manual Search Programme Sort Contrast - Adjusts the contrast ratio. Brightness - Adjusts the luminance of the image. Colour - Adjusts the color intensity, making colors more or less intense. Sharpness - Adjusts the sharpness of the image. Image - Adjusts the image clarity. Options are Normal and Crystal+. Colour Temp - Adjusts the color temperature. Options are Natural, Cold, and Warm. Move Enter Enter Return BACK Move Setting Return BACK NOTE: See 7 Tuning Your LCD TV for detailed procedures for Auto Search and Manual Search. 38 39 Chapter 6 Adjusting Settings Chapter 6 Adjusting Settings Options Menu To access the Options Menu, highlight Options from the Main Menu and press OK. Options Menu Language Parental Control Sleep Timer Factory Preset SCART Autoswitch OSD Type Off Off On 0% English 6-3-2 With Source Input Set to AV1, AV2, AV3, or DTV Language - Changes the language of the OSD menu. Parental Control - Activates parental controls. This option is accessible only from the remote control. Sleep Timer - Turns the sleep timer ON/ OFF. Select 15, 30, 45, 60, 90, or 120 minutes. Factory Preset - Resets user password to 0000 and deletes the analog channel list. SCART Autoswitch - Sets the SCART autoswitch ON or OFF. OSD Type - Sets the transparency of the OSD. Options are 0%, 50%, 100% (OSD gray background), and 50%, 100% (blue background). Move Enter Enter NOTE: The Picture, Sound, and Options Menu for these inputs are the same as those for TV and DTV sources. ENGLISH Return BACK Main Menu Main Menu Picture Sound Sources Options Move Setting Return BACK Sources Menu To access the Sound Menu, highlight Sound from the Main Menu and press OK. Soures Menu Input AV1 AV2 AV3 DTV Video NR Off Off Off Off NOTE: See 8 Advanced Settings for detailed procedures for Parental Control and Sleep Timer. Set the Video NR for each input source from this menu. Turn Video NR ON to reduce on-screen noise. Four modes are available: OFF: LOW: HIGH: not activated if original screen noise is low if original screen noise is high MIDDLE: if original screen noise is middle Move Setting Return BACK 40 41 Chapter 6 Adjusting Settings Chapter 6 Adjusting Settings 6-3-3 With Source Input Set to PC VGA, HDMI, or YUV NOTE: The Sound Menu and Options Menu for this input is the same as the one for TV. Setup Menu To access the Setup Menu, highlight Setup from the Main Menu and press OK. Setup Menu Auto Adjust H-Position V-Position Clock Phase R-Adjust G-Adjust B-Adjust Video NR Move Setting Off Return BACK Off 30 25 30 30 25 30 30 Main Menu Picture Sound Setup Options H-Position - Adjusts the horizontal position of the image. V-Position - Adjusts the vertical position of the image. Clock - Adjusts your LCD TV to match the video input source. Used when patterns appear. Phase - Adjusts the picture to remove any noise such as, horizontal distortion, and clears or sharpens the displayed characters. R-Adjust - Adjusts the red color. G-Adjust - Adjusts the green color. B-Adjust - Adjusts the blue color. Video NR - Turns Video NR ON or OFF. Turn Video NR ON to reduce on-screen noise. Four modes: OFF/LOW/MIDDLE/ HIGH. NOTE: Depending on the selected input source, some options may be disabled (grayed out). Move Enter Enter