User manual SAGEM PHOTO EASY 255

SAGEM PHOTO EASY 255 SY 2 User guide Livret d'utilisation Bedienungsanleitung Manual del usuario Manuale dell'utente Gebruiksaanwijzing S CONTENTS 1 2 3 4 WELCOME Safety instructions and recommendations 1 2 3 4 6 6 7 8 9 11 11 12 13 14 15 17 19 19 20 21 22 22 23 24 25 26 26 27 28 29 31 32 DISCOVER YOUR PHOTO EASY 255 PRINTER THE USER INTERFACE PREPARE YOUR PHOTO EASY 255 PRINTER Connect the mains supply First ribbon installation To change the ribbon Loading paper 5 TRANSFERRING Insert a memory card Transferring photos from a photo GSM Using a camera in DPOF mode Print starting from a bluetooth peripheral (optional) Connect a PC (Personal Computer) Print from a camera (PictBrigde mode) Print Create your shopping basket Zoom Formats Set the photo quality Your preferences YOUR IMAGES 6 PRINT YOUR PHOTOGRAPHS 7 CHOOSING YOUR OWN PRINTER SETTING 8 9 REPLACEMENT OF CONSUMABLES Cleaning the print head Paper jam Problems Error messages Technical data 10 GARANTEE -I- NEDERLANDS ITALIANO MAINTENANCE ESPAÑOL DEUTSCH FRANÇAIS ENGLISH - II - You have just acquired a SAGEM PHOTO EASY 255 printer, and we thank you for choosing our product. With this high quality printer you can get the most out of your digital photos. In a few simple steps you can produce photo prints identical to those from a professional developer, for your personal use or to share with friends and family. The easy-to-follow steps in this user guide will walk you through: · Switching on your PHOTO EASY 255 printer. · Printing photographs stored on a memory card. · Printing photographs transferred from a GSM mobile phone, from a camera in DPOF or Pictbridge mode, or an optional Bluetooth peripheral. · Installing the image processing software and printer driver on a PC. · Maintenance and troubleshooting of your PHOTO EASY 255 printer. · The CD-ROM included with your kit contains an additional guide with instructions for using the image processing software and printer driver on your PC. -1- NEDERLANDS ITALIANO ESPAÑOL DEUTSCH FRANÇAIS ENGLISH 1 WELCOME SAFETY INSTRUCTIONS AND RECOMMENDATIONS · Do not install your PHOTO EASY 255 printer in a humid room (bathroom, laundry, kitchen, etc.), or within 1.50 m of a tap or water source, or outside. The printer should be operated within an ambient temperature range of 10 °C to 35 °C. · Do not install your printer in a location where there is a noticeable amount of dust floating in the air. Such dust can degrade the print quality of your photos. · Only the power supply provided with the printer should be used. Connect this to the mains in accordance with the installation instructions in this user guide and the information on the identification label affixed to the power supply (voltage, current, mains frequency). As a precaution, in case of danger, the mains adapters act as a disconnecting mechanism for the 230V power supply. They should be placed near the device and should be easily accessible. · Never open the cover of the film cartridge compartment during printing. This could break the film and cause printer malfunction. · Only use SAGEM consumables, if not you are likely to damage the equipment and invalidate the guarantee. To obtain the references of the consumables (refer to the paragraph Replacement of consumables, page 25). · The CE marking certifies that the product meets the main requirements of the European Parliament and Council directive 1999/5/CE on telecommunications terminal equipment, regarding safety and health of users, and regarding electromagnetic interference. The declaration of compliance can be consulted on the site www.sagem.com category "support", or can be requested at the following address: E - Customer relations department 4 rue du petit Albi - 95800 Cergy Saint-Christophe - FRANCE -2- Check that the following elements are present: 1 2 3 4 5 6 7 8 9 10 PHOTO EASY 255 printer User manual CD-ROM with its applications Film cartridge * Photo paper (2 packs of 20 sheets)* USB cable Paper tray Power supply unit Mains cable xD card adapter 10 PH O EA OT O M GE SA 155 SY 9 2 de r gui Use ion utilisat g et d itun Livr anle ario ngs ienu del usu ente Bed ual dell'ut g Man uale nwijzin Man saa ruik Geb S 8 3 1 7 4* -3- NEDERLANDS * depending on model 5 * ITALIANO 6 ESPAÑOL DEUTSCH FRANÇAIS ENGLISH 2 DISCOVER YOUR PHOTO EASY 255 PRINTER 3 THE USER INTERFACE The user interface enables you to: · Select photos one by one or switch over to mosaic mode (6 photos displayed on screen), · Print a photo directly, · Activate auto improvement before printing a photo, · Set the "Format", "Preferences" and "Image settings" parameters according to your needs, · Select several photos and choose a different number of copies for each photo to be printed, · Zoom onto a photo and print it. Description of the user interface: 1. Mains lamp 2. On/Off button 3. Menu access button 4. Cancel button (C) 5. Zoom - and mosaic mode activation button 6. CRYSTAL IMAGE button (auto print quality improvement) 7. Print button 8. Confirm button (OK) 9. Zoom + button 10.Browser -4- The visual interface All the valid photos are displayed on the screen; use the or buttons to scroll through them: 1 2 3 4 5 6 ENGLISH NEDERLANDS -5- X1 7 8 11 10 The following information is available on the screen: 1. Photo selected 3. Total number of valid photos contained in the memory card or connected source 4. Auto improvement function icon 5. Print format 6. Number of the sheet to be printed 7. Number of copies of the photo 9. Date when the photo was taken in Year/Month/Day format 10.Add a copy, 11.Remove a copy, button button ITALIANO ESPAÑOL 2. Number of the photo selected 8. Photo filename DEUTSCH 9 FRANÇAIS 4 PREPARE YOUR PHOTO EASY 255 PRINTER CONNECT Remark THE MAINS SUPPLY : When installing your printer near a wall or some other object, keep an open space of at least 4 inches at the back of the printer, to make sure the movement of the sheet of paper being printed is not obstructed. Please refer to the safety instructions at the beginning of this user guide before making any connections. Insert one end of the mains lead into the corresponding socket of the power supply. Connect the power supply prug to the printer, pushing it in fully as shown in the illustration below. Plug the other end of the power supply mains lead into a wall socket. Press the On/Off button until the red light comes on. The language selection screen appears when you switch the printer on for the first time. Use the browser's or keys to select the language you want and press the key to confirm. The S and the message "Waiting for memory card or other image source" are displayed on the screen. -6- FIRST Remark RIBBON INSTALLATION ENGLISH NEDERLANDS -7- : Use DSR400 or DSR400T consumables only. These are specially designed to provide you with optimum print rendering. Switch on the printer. Wait 10 seconds for the printhead to lift, then: 1. Open the external flap located on the right-hand side of the printer. 2. Remove the protective foam. FRANÇAIS ITALIANO ESPAÑOL DEUTSCH 3. Take the new ribbon out of its packaging and make sure that the film is stretched after removing the card (A). 4. Install the ribbon in the position shown in the illustration below. 5. Lift the locking lever and push in the film cartridge until it touches the back of the compartment the locking lever must be locked after insertion. 6. Close the external flap. A 6 TO Remark CHANGE THE RIBBON : Use DSR400 or DSR400T consumables only. These are specially designed to provide you with optimum print rendering. For this purpose, the printer must read the chip card delivered with each consumable kit after any new kit installation. Switch on the printer. Wait 10 seconds for the printhead to lift, then: 1. Take the PLUG N'PRINT card delivered with the ribbon and the photo paper. Insert it in the drive located on the front panel of the printer. The PLUG N'PRINT card is recognised and read by the printer ; the following message is displayed at the end of the procedure "Transfer OK (40 or 120), Remove card". 2. Remove the PLUG N'PRINT card ; the display returns to the welcome screen. 3. Take the new ribbon out of its packaging and make sure that the film is stretched after removing the card (A). 4. Open the external flap located on the right-hand side of the printer. 5. Lift the locking lever and remove the used ink ribbon. 6. Install the ribbon in the position shown in the illustration below. 7. Lift the locking lever and push in the film cartridge until it touches the back of the compartment the locking lever must be locked after insertion. 8. Close the external flap. A 6 7 8 -8- LOADING PAPER ENGLISH Protection sheet 1. Pull the paper tray out of the printer. 2. Open a pack of paper with the protection sheet on the top, insert it in the paper tray, making sure the rectangle reserved for postage stamps is on the outside of the tray, that is, towards you. 3. Remove the protection sheet. 4. Line up the tray with its compartment and push it in slowly until the locking system clicks. Warning - Handle paper sheets by their pre-cut edges, never allow your fingers to come into contact with the shiny surface before printing. -9- NEDERLANDS Your SAGEM PHOTO EASY 255 printer is now ready to print your digital photographs. ITALIANO ESPAÑOL DEUTSCH FRANÇAIS Warning - Protect consumable items against prolonged exposure to light, humidly, heat and dust. Respect the operation conditions set out (refer to the paragraph Technical data, page 31). Only use SAGEM brand consumable items designed for this printer. Warning - Make sure that a previously printed photograph has not been slipped inadvertently into a packet of blank pages; this could damage the ribbon of your printer. - 10 - INSERT A MEMORY CARD Warning - The memory cards do not enter fully in the reader slot. DO NOT USE FORCE UNDER ANY CIRCUMSTANCES. Warning - Printing of picture by ascending order relatively to the date of the pictures on the memory board will be achieved if parameters "dates and hour" have been set on your camera before the catch of pictures. Otherwise pictures will be read and printed in a random order. FRANÇAIS NEDERLANDS - 11 - Card Slot Location DEUTSCH ITALIANO ESPAÑOL Smart Media (SM) Left Memory Stick (MS) Left Standard Digital (SD) Left Multi Media Card (MMC) Left ENGLISH 5 TRANSFERRING YOUR IMAGES xD card with its adapter Left CompactFlash Right TRANSFERRING PHOTOS FROM A PHOTO GSM Photographs taken with a GSM mobile phone equipped with a camera can be printed on the SAGEM PHOTO EASY 255 printer. To do this, the photographs need to be transferred to the printer via an IR (infrared) link between the 2 devices. Tips - GSM mobile phones with cameras work on low definition ; for a better quality of print we suggest you print 2 or 4 photos per sheet. Switch the printer on. Place your GSM mobile phone opposite the SAGEM PHOTO EASY 255 printer so that the IR "windows" are facing each other and are not more than 30 centimetres apart. Warning - In an environment exposed to intense light, a distance of not more 10 centimetres between the two infrared windows is recommended. Select a photograph on your GSM mobile phone and start the IR ink transfer. - 12 - You can now: · Start printing the transferred photograph, after setting the print format and number of copies if required. · Transfer another photograph from your GSM mobile phone camera, which will be added to those already stored in the printer. At the end of each transfer, the total number of photographs stored is displayed on the printer screen (the one with the highest number being the last one transferred). · The same operations as described in the previous chapters can now be performed before starting to print the photographs: (selecting the photographs to be printed, selecting the format, selecting the number of copies). After all photographs transferred from your GSM mobile phone camera have been printed, the SAGEM PHOTO EASY 255 printer screen displays the information that was on the screen just before you started the print job. You can now: · Start another print job, after selecting different parameters (photograph number, format, number of copies) if required. · End the transferred photograph processing. To do this, hold the down for 3 seconds. key USING A CAMERA IN DPOF MODE Select the required photographs on the camera (follow the instructions in the documentation of your camera). NEDERLANDS Switch the printer on. Place the memory card into its slot. The following message is displayed on the screen "Print the camera DPOF selection? - C : No - OK : Yes". - 13 - ITALIANO This function lets you select the photographs to be printed on your camera, then print them on the SAGEM PHOTO EASY 255 printer from a memory card. Your camera must comply with the DPOF (Digital Print Order Format) standard. Refer to your camera documentation to find out if it is compatible with this standard. ESPAÑOL DEUTSCH FRANÇAIS ENGLISH The message "Infrared transfer - Please wait" blinks on the printer screen throughout the transfer operation. Start printing by pressing the To exit DPOF mode, press the key. key. PRINT STARTING (OPTIONAL) FROM A BLUETOOTH PERIPHERAL The adapter of Bluetooth (optional equipment) printer is a fast and effective solution to pass from a telegraphic connection to a connection without wire. The adapter makes it possible to transform printing SAGEM PHOTO EASY 255 into Bluetooth receiver thus authorizing equipment equipped with technology Bluetooth like the personal assistants, the office computers, portables or others the impression of photographs. Ensure that all hardware units are powered. Never force installation of connectors on hardware, as the cable and the connector could be damaged. Connect the Bluetooth adaptor (optional equipment) to the USB port (A) of your SAGEM PHOTO EASY-255 printer. A Identification among hardware units is automatic. Warning - The size of the photo or photos to be transferred to the SAGEM PHOTO EASY-255 printer must be less than 600 Kbytes. The photo format required is the JPEG format. An error message "Wireless memory full" will - 14 - be displayed when the maximum storage capacity is reached. To transfer new data to the SAGEM PHOTO EASY-255 printer, you must clear the memory. To do this, press and hold the key for 3 seconds . ENGLISH NEDERLANDS - 15 - When the transfer is complete, the following information is displayed on the screen "Bluetooth transfer - Please wait" You can now: · Start printing the transferred photograph, after setting the print format and number of copies if required. · Transfer another photograph, which will be added to those already stored in the printer. At the end of each transfer, the total number of photographs stored is displayed on the printer screen (the one with the highest number being the last one transferred). Remark : the following message is displayed if the EASY PHOTO 255 printer memory is full "Wireless memory full". FRANÇAIS ITALIANO ESPAÑOL DEUTSCH CONNECT A PC (PERSONAL COMPUTER) Your kit includes an installation CD-ROM containing a printer driver, image processing software. Make sure that your PC is compatible with the requirements as specified : PC configuration required: Pentium or equivalent, OS : Windows 98 SE / 2000 / Me / XP, 128 MB DRAM or more, 150 MB available on hard disk, USB port available. Install the software Insert the CD-ROM in the drive to start installation. A command window appears. Follow the instructions displayed on the screen. If the installation program does not start automatically, you can start it by double-clicking on the "setup.exe" file located in the CD-ROM root directory. The SAGEM PHOTO EASY 255 software is installed in three steps: running the Install program, restarting the computer, and performing the final printer installation. Do not connect the printer to the PC before installing the printer driver. After you have installed the software, a message will be displayed asking you to restart the PC. After restarting you can connect the printer to the PC. The CD-ROM contains an installation manual which includes detailed operating instructions for the printer driver. Refer to this manual for further information. Remark : The B/W print option is not available in Windows 98. Connect your printer Make sure that both the PC and the printer are switched on. Never apply force when plugging in connectors into the equipment as this could damage both the cable and the connector. Connect the USB cable to a USB port on your PC. Connect the other end of the USB cable on the SAGEM PHOTO EASY-255 printer to the USB port (B).. B - 16 - Recognition between the two devices is automatic PRINT FROM A CAMERA (PICTBRIGDE MODE) Your printer PHOTO EASY 255 SAGEM supports the standard PictBrigde, it thus allows the impression of photographs starting from cameras compatible with this standard. Read the documentation of the camera to check compatibility with the PictBrigde standard and to check the connection with the printer. FRANÇAIS NEDERLANDS ITALIANO ESPAÑOL DEUTSCH Start PictBrigde mode printing Check that camera is set up in PictBrigde mode. Connect the USB cable to the USB port (A) on the PHOTO EASY 255 printer. A Once the analysis and recognition phase is complete, a screen is displayed indicating PictBridge mode. The CRYSTAL IMAGE print quality improvement function is activated by default. Press the key to remove it. When the photo is transferred, printing starts automatically and the green lamp flashes. Remove the USB cable to exit PictBridge mode. - 17 - ENGLISH In PictBridge mode, your SAGEM PHOTO EASY-255 printer supports the following functions: Printing a photo. Selecting photos and printing them several times on the same paper. Printing from a DPOF-standard file. Monitoring printing and especially the beginning, progress and end of the printing process. Also, error messages likely to occur (no paper, paper jam, end of ribbon, system error). Your SAGEM PHOTO EASY-255 printer does not support the following functions: Image cropping. Choosing a type of paper. Providing additional data (for example, date and time), in addition to the photo to be printed. - 18 - Your SAGEM PHOTO EASY 255 printer is designed to be used with or without a computer. This chapter describes printer operation without a computer. Refer to the technical data table at the end of thi user manual to check whether your memory card is compatible with the printer. In the event of incompatibility, use a computer and the image processing software supplied on the CD-ROM. Warning - Small sized images, less than 76,800 pixels, cannot be printed from memory cards. On the other hand, these photographs may be printed from a PC or by means of a wireless IR link (or Bluetooth optional equipment). Switch your printer on. Insert or connect a source (memory card, camera in DPOF or PictBridge mode, GSM phone with an InfraRed or Bluetooth optional peripheral device). After the analysis and loading phase, the last photo saved is displayed on screen. Use the browser's or keys to move from one photo to another. Press the key to display the Print menu. In this menu you may select: The photo that is displayed on the screen select: Print current photo, The shopping trolley you selected earlier : select Print selection (refer to the paragraph Create your shopping basket, page 20), All the photos recognised on the source : select Print all, To print all the photos in miniature format with twenty photos per sheet of paper, select Print index. Make your selection using the browser's or keys. Press the CRYSTAL IMAGE button to improve the quality of your photo. The icon is displayed on screen when this function is active. Check that you have enough paper in the drawer. Press the button again or the button to start printing. - 19 - NEDERLANDS ITALIANO ESPAÑOL PRINT DEUTSCH FRANÇAIS ENGLISH 6 PRINT YOUR PHOTOGRAPHS Tips - The CRYSTAL IMAGE process developed by e works on each photo individually to use its full colour potential and the definition of your printer. e highly recommends that you use this function. Tips - You may remove the edges from a series of photos by placing several sheets one on top of the other. Warning - When all the photos are printed, do not tear off these edges in one movement ; fold the edges along the dotted lines several times before removing the edges gently. Idea - The pre-printed postcard format on the back lets you send your photo quickly to friends or family. CREATE YOUR SHOPPING BASKET You may store any selections of series of photos you make, with different print quantities for each one. To do so, proceed as follows: There are 2 modes to browse between photos: Full-screen mode to browse image by image, Mosaic mode, accessed by pressing the quickly through 6 images (the mode). The browser Press the Press the key, lets you browse more key then lets you return to full-screen lets you move from one image to another. key to put the photo displayed into you shopping basket. key again, once for each copy you want. Press the key to remove the selected photo or to remove a copy from your shopping basket. Repeat the operation above for each photo you want to add to your shopping basket. Once selected, the quantity is displayed preceded by an X in the top right hand corner for each photo. Press the key to display the Print menu. - 20 - Make your selection using the browser's or keys. button again or Check that you have enough paper in the dawer. Press the the button to start printing. ZOOM Select the photo you want using the browser's or keys. or keys to key. FRANÇAIS NEDERLANDS - 21 - Press the key to activate zoom mode. Use the browser's select Portrait or Landscape and confirm by press the or Use the browser's keys to move to the part of the photo to be enlarged. Press the key to preview the result. The enlarged photo is displayed on screen. Press the key to cancel. key to confirm or the The print area is represented on screen by a red rectangle. Press the key for each copy you want; the number of copies is displayed in the top right hand corner of the photo. Remark : This photo may be printed immediately or entered into a shopping basket selection to be printed later. ITALIANO ESPAÑOL DEUTSCH Adjust the size of the zoom you want using the or keys. The zoom may be adjusted from 100% to 300% with the following ranges 100%, 120%, 140%, 160%, 200%, 240% and 300%. ENGLISH 7 CHOOSING YOUR OWN PRINTER SETTING There are several parameters that you may set according to how you use your printer. Press the key to set the paper formats, the image quality and your own preferences. FORMATS This function lets you select a paper format to suit your own needs, for example, to print passport photos selected the 8 photos per page format. Press the key, and select the Format menu using the browser's keys. Press the key to confirm. or You may print your photos according to the following predefined formats : · Print your photo in 10 x 15 cm Full Page format with no edging · Print your photo in 10 x 15 cm format With Margins · Avec Margins .Print your photo in Full Page 4/3 format · Print 2 photos per page · Print 4 photos per page · .Print 8 photos per page · Print 20 photos per page · Print 2 pages per image · Print 4 pages per image . . . (contact sheet or index). (the photo is printed over 2 pages). (the photo is printed over 4 pages). or keys. Press the . . . Select the paper format you want using the browser's key to confirm and return to browse mode. - 22 - SET THE PHOTO QUALITY ENGLISH NEDERLANDS ITALIANO ESPAÑOL DEUTSCH FRANÇAIS This menu lets you adjust the colour parameters for the selected photo according to your own requirements. Press the or keys. key and select the Image settings menu using the browser's Select the parameter to be modified using the browser's p or q keys. The browser's or keys are used to modify the value of the selected parameter. The key lets you exit the current image setting screen without confirming the modifications. You then return to the previous menu. You may set: · The Contrast of the photo between -2 et +2 ; use the browser's or keys to make your selection. · The Brightness of the photo between -2 et +2 ; use the browser's or keys to make your selection. · The Sharpness of the photo between -2 et +2 ; use the browser's or keys to make your selection. · The Effect of the photo: None for no settings, B&W to print a photo in black and white, Sepia to print a photo in yellow, magenta and cyan over three sheets of paper. Use the browser's or keys to make your selection. · The Colour of the photo between -2 et +2 ; use the browser's or keys to make your selection. · A Frame around your photo : No for no frame, Other frames to print a predefined frame. Use the browser's or keys to make your selection. When you have made all the modifications you want, press the key to confirm and return to browse mode. An icon is displayed at the bottom right of the photo to indicate that specific settings have been made. The modifications made are only valid for the selected photo. Warning - If you press the into account. - 23 - key while you are setting the parameters you will automatically return to browse mode without taking any modifications YOUR PREFERENCES This menu lets you modify the printer's default settings. Press the key and select the Preferences menu using the browser's keys. Press the key to confirm. Select your preference using the browser's key to confirm. or keys and press the or You may select: · The Language which will be used in the screens. Use the browser's or keys to select between Français, Español, Português, Deutsch, Nederlands, Italiano and English. Press the · The Format preference , use the browser's paper format you want. Press the · The Copies preference1, use the browser's 1 key to confirm. or or keys to select the keys to select the key to confirm. number of copies you want, from between 1 and 20 photos. Press the key to confirm. · The Image preference1 menu lets you modify the settings for the images, refer to the paragraph Set the photo quality, page 23 to modify these parameters. To modify the automatic image improvement, select the Auto improvement command and press the key to confirm. · The After printing lets you keep or erase the selection stored in the memory. Using the browser's or keys select the Keep selection or Erase selection command and press the key to confirm. · The screen's LCD contrast between -8 and +8. Use the browser's or keys to make your selection and press the X key to confirm. · The Restore param. Menu lets you return to the original values. Press the key to confirm and the parameters will be reset after a few seconds. 1. These preferences are taken into account each time a new card is inserted. - 24 - The consumable items used with the SAGEM PHOTO EASY 255 printer (film cartridge, paper) are SAGEM (PLC) brand products. Consumables may be purchased in all big stores in the photography or printer sections but also on out internet site www.sagem.com or by using the consumables order form supplied with your printer. Use of any consumable items other than SAGEM (PLC) brand products may result in the loss of the printer's guarantee. DSR400 consumable item kit references: (ribbon + paper for 40 photos): ref. 251 559 421 - 25 - NEDERLANDS ITALIANO ESPAÑOL DSR400 consumable kit references: (ribbon + paper for 120 photos):ref. 251 559 434 DEUTSCH FRANÇAIS ENGLISH 8 REPLACEMENT OF CONSUMABLES 9 MAINTENANCE CLEANING THE PRINT HEAD Continuous lines across the length of your photographs may be caused by dirt particles stuck to the printhead. You will need a methylated alcohol1 based cleaning product and some off-the-shelf cotton tips ("Q-tips"). Switch off your printer, disconnect the main cables and wait for five minutes; since the print head operates at a high temperature, there is a risk of burning if you touch it. 1. Open the cartridge flap. Press on the locking lever and pull out the film cartridge. 2. Pull out the paper tray. 3. Turn the printer upside down to remove the lower hatch. 4. Clean the heating line of the print head carefully using a cotton bud. 5. Replace the lower hatch, turn the printer right side up, connect the mains cable and switch on the printer. Warning - Never touch the print head with your fingers or any object that might scratch it. 1 2 3 4 5 1. Do not use corrosive chemicals, they may damage your printer. - 26 - Push the paper tray back into place until the locking system clicks. PAPER JAM FRANÇAIS NEDERLANDS - 27 - Follow this procedure if a sheet becomes stuck in the printer and cannot simply be pulled out: Switch off your printer. Turn the printer upside down. Remove the lower cover. Gently and carefully remove the sheet causing the jam. Under no circumstances touch the printhead. Replace the lower cover and turn the printer right side up. Switch on the printer and reconnect the mains cable. Warning - Never use objects that could damage the printer (scissors, screwdriver, paper cutter, etc.). ITALIANO ESPAÑOL DEUTSCH ENGLISH Replace the film cartridge. Take care that the film is taut before inserting the cartridge into its compartment. Check that the locking lever is pushed down correctly and close the flap. PROBLEMS Remark : The printer is fitted with an automatic time-out to prevent overheating, this can be tripped when performing large print jobs. The printer automatically restarts the current print job as soon as the temperature drops back to normal. PROBLEMS SOLUTIONS · Check that the power supply block is correctly plugged into the mains. · Check that the power supply connector is correctly plugged into the printer. · Checkthat the mains socket is live (check fuses and/or circuit breakers of your installation as necessary). · Refer to the error message table (refer to the paragraph Error messages, page 29). · Set the printer on/off switch to O and then reconnect the mains lead. · Switch on the printer and wait for the initialisation phase to be completed. · If a sheet of paper is jammed, carry out the procedure (refer to the paragraph Paper jam, page 27). · Restart printing. · Are you using sheets that meet the technical specifications (refer to the paragraph Technical data, page 31). · Have the sheets been inserted shiny face up? · Clean the printhead (refer to the paragraph Cleaning the print head, page 26). · Check that the USB cable is correctly connected. · Is the printer driver installed? No mains supply (indicator lamp off) An error message is displayed on screen The printer was unplugged during a print job No photograph is printed on a sheet The photograph is marked with a continuous line or a lot of spots No PC printing - 28 - ERROR MESSAGES After any intervention on your printer, do not forget to press the restart the current print job. Error displayed Paper tray empty key to Error Type Resolve error, then press PRINT key to resume printing Resolve error, then press PRINT key to resume printing Resolve error, then press PRINT key to resume printing Resolve error, then press PRINT key to resume printing Resolve error, then press PRINT key to resume printing Resolve error, then press PRINT key to resume printing Resolve error, then press PRINT key to resume printing Remove card Error type Action Check that the paper has been correctly inserted in the loading tray. Remove any paper jammed in printer (do not reuse this sheet of paper). Paper Paper jam Paper Check ribbon Ribbon End of ribbon Ribbon Replace the film cartridge with a new one. Check that the film cartridge is correctly inserted. If error persists: replace the cartridge. Check that the cartridge is correctly inserted and that the locking lever is locked. The selected number of photos is greater than the remaining ribbon capacity to print all photos. The smart card has already been used. Remove the inserted card and insert a valid smart card. The authorized print quantity has been reached. Data transfer error. Remove the inserted card and insert a valid smart card. Data transfer error. Remove the inserted card and insert a valid smart card. Ribbon error Ribbon Cassette error Ribbon Insert ribbon parameter card Ribbon Card empty Counter saturated Card unreadable (01) Card unreadable (02) SmartCard Remove card SmartCard Remove card SmartCard Remove card SmartCard - 29 - NEDERLANDS ITALIANO ESPAÑOL DEUTSCH Insert a new film cartridge or replace the current one. FRANÇAIS ENGLISH Erreur affichée Card unreadable (03) Consumable not compliant (01) Consumable not compliant (02) Consumable not compliant (03) Consumable not compliant (04) Consumable not compliant (05) Correction affichée Remove card Type d'erreur SmartCard Action Data transfer error. Remove the inserted card and insert a valid smart card. Mechanical problem. Remove card Smart Card Remove card Smart Card Ribbon problem. Remove card Smart Card Brand name not dentified. Remove card Smart Card Colorimetry error. Remove card Unrecoverable error, abort the operation and try again Unrecoverable error, abort the operation and try again Unrecoverable error, abort the operation and try again Unrecoverable error, abort the operation and try again Please contact your dealer Smart Card Type (master/pack) unknown. File damaged JPEG decompression The JPEG file contains an unsupported feature. Format not supported Transfer error Photograph to be transferred is not in JPEG format. Error during transfer of photographs from GSM mobile phone camera. Restart transfer from the GSM phone. Check that both devices are facing each other. Switch off printer, wait 30 seconds and restart. If error persists, contact your retailer. Switch off printer, wait 30 seconds and restart. If error persists, contact your retailer. Transfer error Transfer error Wireless memory full Transfer error System error Other - 30 - TECHNICAL DATA ENGLISH NEDERLANDS ITALIANO ESPAÑOL DEUTSCH FRANÇAIS PC configuration required: Pentium or equivalent, OS : Windows 98 SE / 2000 / Me / XP, 128 MB DRAM or more, 150 MB available on hard disk, USB port available. ----------------------------------------------------------------- Device name Print method Resolution Colours Print speed : : : : : Interface : SAGEM PHOTO EASY 255 Dye-diffusion thermal transfer 300 x 300 dpi 16.7 million continuous Less than 120 seconds per photo (not including data transfer) Memory cards, type Compact Flash (support type I & II), SM / MS / MMC / SD / xD (with adapter), USB port version 1.1. Storage of photographs transferred from a GSM phone camera : Image resolution supported : Consumable items : Up to 500 kilobytes Up to 12 million pixels Photo-quality paper. Film cartridge with three colours (yellow, magenta, cyan) and protective coating, 40 print operations per cartridge. Paper size : 101 X 152,4 mmavailable in packets of 20 sheets Paper tray : By automatic loader, capacity 20 sheets Mains supply : 230 V AC 50/60 Hz Approval : EC Operating conditions : 10 °C to 35 °C, 30 % to 85 % humidity Size : 201 x 174 x 94 mm excluding paper tray Weight : 1.5 kg (except power supply unit) Power consumption : in standby: 7,6 W in print mode: 70 W All data are provided for reference purposes only. SAGEM (PLC) reserves the right to make any changes without prior notice. - 31 - 10