CONVERSION KIT INSTRUCTIONS 901 Cambridge Drive Elk Grove Village, IL 60007 Phone: (847) 364-9787 Fax: (847) 364-9831 Web: www.sammyusa.com © 2002 Sammy USA Corporation CONTENTS PLEASE READ BEFORE INSTALLING... 1. KIT PACKAGE CONTENTS 2. GAME PLAY 3. CONNECTOR TABLES 4. DIP SWITCH TABLES 5. LAYOUT OF P.C.BOARD 6. HOW TO ASSEMBLE THE KIT 7. TEST MODE 8. TROUBLE WITH GUN SHOOTING 9. WARRANTY Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7, 8 Page 9, 10, 11 Page 12 Page 13 PLEASE READ BEFORE INSTALLING THE WING SHOOTING CHAMPIONSHIP KIT The WING SHOOTING CHAMPIONSHIP KIT is designed only for a Normal resolution monitor. The High or Medium resolution monitor will not work for WING SHOOTING CHAMPIONSHIP KIT . MIS-CONNECTING THE GUN CONNECTOR When you connect the Gun unit to Main PCB, you must always make sure to connect to the correct connectors which are CN 5 & CN 6 and CN 7 & CN8 connectors. If you connect Gun unit to CN 2, 8 pin connector, your PCB will sustain serious damage. Connector of 1 Player Gun Assy Connector of 2 Player Gun Assy Connect 10 pin connector of Gun Assy Connector to both 4 pin connectors like above. CN 5 & CN6 CN 2 CAUTION!! NEVER CONNECT GUN UNIT TO CN2. CN 7 & CN8 1 1. KIT PACKAGE CONTENTS A Main P.C.Board 47-10-001 B START button Assy, Hunter 1 47-50-013 C START button Assy, Hunter 2 47-50-015 D Instruction Decal Sheet 47-30-210 E "PUMP BEFORE SHOOTING" Decal 47-30-224 F Marquee Styrene 47-30-100 G Control Overlay 99-30-150 H Side Decal (2 sheets) 47-30-200 I Gun Holster (2 sets) 99-50-303 J Conversion Kit Instructions 47-30-300 K AAMA Sticker 99-30-750 ANIMATED VIOLENCE MILD CONVERSION KIT INSTRUCTIONS L Gun Assy (2 guns) 99-50-310 2 2. GAME PLAY Wing Shooting Championship is a sports hunting game that has an exciting COMPETITION MODE. Two players can play at the same time in competition mode which is a first time for the market! HOW TO PLAY Insert coin(s) Press Hunter 1 or Hunter 2 button to start game. Use Sammy 27" Shotgun to select stage and weapon. (Pump the Shotgun before you shoot the screen each time.) There are 5 kinds of weapons. PUMP ACTION (5 bullets), SEMI-AUTO (3 bullets) OVER&UNDER (2 bullets), SIDE BY SIDE (2 bullets) SINGLE SHOT (1 bullet) 6 different bird stages. (GREAT PLAINS QUAIL, RING-NECKED PHEASANT, CANADA GOOSE, AMERICAN BLACK DUCK, MALLARD DUCK and EASTERN BOB WHITE QUAIL) 12 areas with one bonus stage for each bird. The Bonus stage is CLAY SHOOTING. Perfect round in bonus stage advances to a SPECIAL STAGE! 3 3. CONNECTOR TABLES JAMMA CONNECTOR MAIN P.C.BOARD SOLDER SIDE FUNCTION COLOR GROUND GROUND +5VDC +5VDC +12VDC KEY COIN METER B COIN LOCKOUT B SPEAKER(-) VIDEO GREEN VIDEO SYNC BLK BLK RED RED BLU PIN # PIN # COMPONENT SIDE COLOR FUNCTION BLK BLK RED RED BLU GROUND GROUND +5VDC +5VDC +12VDC KEY COIN METER A COIN LOCKOUT A SPEAKER(+) VIDEO RED VIDEO BLUE VIDEO GROUND TEST SWITCH COIN SWITCH A 1P START BUTTON BLK GRN WHT SERVICE CREDIT SWITCH BRN/WHT COIN SWITCH B 2P START BUTTON GROUND GROUND BLK BLK A B C D E F H J K L M N P R S T U V W X Y Z a b c d e f 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 WHT/BLK RED BLU BLK WHT/GRY BLK BLK GROUND GROUND CN6 - 4 PIN SUB CONNECTOR MAIN P.C.BOARD (1P GUN) PIN # COLOR GREEN BLACK CN8 - 4 PIN SUB CONNECTOR MAIN P.C.BOARD (2P GUN) PIN # COLOR GREEN BLACK FUNCTION PUMP SWITCH PUMP SWITCH GND FUNCTION PUMP SWITCH PUMP SWITCH GND 1 2 3 4 1 2 3 4 CN5 - 4 PIN SUB CONNECTOR MAIN P.C.BOARD (1P GUN) PIN # COLOR RED WHITE BROWN BLUE CN7 - 4 PIN SUB CONNECTOR MAIN P.C.BOARD (2P GUN) PIN # COLOR RED WHITE BROWN BLUE FUNCTION +5VDC TRIGGER SWITCH GROUND OPTICAL FUNCTION +5VDC TRIGGER SWITCH GROUND OPTICAL 7 8 9 10 7 8 9 10 4 4. DIP SWITCH TABLES DIP SWITCH 1 FUNCTIONS COIN CHUTE A, B SETTING 1 COIN START, 1 COIN CONTINUE 2 COINS START, 2 COINS CONTINUE 2 COINS START, 1 COIN CONTINUE 3 COINS START, 3 COIN CONTINUE 3 COINS START, 2 COINS CONTINUE 3 COINS START, 1 COIN CONTINUE 4 COINS START, 4 COINS CONTINUE 4 COINS START, 3 COINS CONTINUE 4 COINS START, 2 COINS CONTINUE 4 COINS START, 1 COIN CONTINUE 1 COIN 2 CREDITS, 1 CREDIT START & CONTINUE 1 COIN 3 CREDITS, 1 CREDIT START & CONTINUE 1 COIN 4 CREDITS, 1 CREDIT START & CONTINUE 1 COIN 5 CREDITS, 1 CREDIT START & CONTINUE 1 COIN 6 CREDITS, 1 CREDIT START & CONTINUE FREE PLAY 1 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON 2 OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON SWITCH POSITIONS 3 OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON 4 OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON OFF OFF OFF OFF ON OFF ON 5 6 7 8 NOT USED TEST MODE DIP SWITCH 2 FUNCTIONS SETTING 1 OFF ON OFF ON 2 SWITCH POSITIONS 3 4 5 6 7 8 MONITOR SETTING 1 NORMAL REVERSE VERTICAL MONITOR SETTING 2 NORMAL REVERSE HORIZONTAL ON ATTRACT SOUND OFF DIFFICULTY LEVEL NORMAL EASY HARD HARDEST NOT USED CHANCES GUN TYPE 2 3 PUMP ACTION GUN UNIT HAND GUN UNIT OFF ON OFF ON OFF ON OFF OFF ON ON OFF ON OFF ON OFF ON "FACTORY INSTALLED" SETTING 5 5. LAYOUT OF P.C.BOARD MAIN P.C.BOARD SUB CONNECTOR 4 PINS X 2 (2P GUN) JAMMA CONNECTOR VOLUME 1 10 1 8 ON OFF CN 8 CN 7 1 DIPSW 1 10 SUB CONNECTOR 4 PINS X 2 (1P GUN) CN 6 CN 5 MAX 1 8 ON OFF DIPSW 2 6 6. HOW TO ASSEMBLE THE KIT 1. Change the GAME CABINET · MARQUEE STYRENE Change the old marquee to the WING SHOOTING CHAMPIONSHIP Marquee Styrene. NOTE: If the WING SHOOTING CHAMPIONSHIP Marquee Styrene does not fit your cabinet, you should cut the marquee to fit. · CONTROL PANEL Change the parts on the control panel. Take off the old parts (Joystick or Gun unit assy) and the old push button assys from the control panel. Then put on the WING SHOOTING CHAMPIONSHIP Control Panel Overlay. NOTE: After you put on the WING SHOOTING CHAMPIONSHIP Control Panel Overlay, you must make the holes for the WING SHOOTING CHAMPIONSHIP Gun Assy, Gun Holster and Push Button Assy. See sample layout below. Or if you want, install Gun Assy or Gun Holster on the side of Cabinet. MOUNTING DIMENSIONS FOR PUSH BUTTON ASSY MOUNTING DIMENSIONS FOR GUN ASSY 0.20 dia. 3 HOLES 1.0" dia. HOLE 3.00" 1.50" 1.50" 0.87" 2.47" 1.60" 1.5" dia. HOLE MOUNTING GUN HOLSTER You can mount GUN HOLSTER to the top of the control panel or side of cabinet. To mount it, use HOLSTER as a template for drilling holes. Use a hex wrench to tighten screws. IF YOU WANT TO INSTALL A HAND GUN: You can use a HAND GUN instead of the original pump action gun for this game. *WARNING* Be absolutely sure that the connector for the hand gun matches exactly the pin position for CN5 (1P Gun) and CN7 (2P Gun) as shown on page 4. Connect 1P Gun connector to CN5, 2P Gun connector to CN7 and turn on Dip switch 2, #8. See page 5 for Dip switch table. 7 · INSTRUCTION DECAL SHEET Put "PUMP BEFORE SHOOTING" Decal Sheet on the front glass of the monitor. MONITOR PUMP BEFORE SHOOTING DECAL AAMA STICKER · AAMA "ANIMATED VIOLENCE MILD" STICKER Place AAMA sticker on the upper left hand side corner of the marquee. ANIMATE VIOLENCE MILD Remove old P. C .Boards and install new P. C. Board in its place. 2. Connect the HARNESSES · JAMMA HARNESS Connect the JAMMA Harness to the edge connector on the Wing Shooting Championship Main P.C.BOARD. · GUN HARNESS Connect the Gun Harness to the Gun Connectors located on the Main P.C. Board components side, at CN5 & 6 and CN7 & 8 connectors on the P.C. BOARD. Connect Gun Connector to CN5 & 6 and CN7 & 8, correctly, as shown below. 10 pin connector from GUN Assy (1P) 10 pin connector from GUN Assy (2P) CN 5 10 1 CN 6 CN 7 10 1 CN 8 Connectors on the Main PCB Connectors on the Main PCB 8 7. TEST MODE Entering the TEST MODE If you need to check the condition of the game circuitry and controls, you can use the TEST MENU. Turn ON "DIP SWITCH 1, #8" and re-power on the game. The game will go into TEST MODE (diagnostics) and the screen appears as follows: Select TEST Use this screen to choose which of the 7 screens you want to see. Move cursor using the START BUTTON. Then pull the TRIGGER to enter the function. TEST MENU 1. 2. 3. 4. 5. 6. 7. 8. GUN MENU COLOR TEST CROSS HATCH I/O TEST SOUND TEST MEMORY TEST OPTIONAL SETTING REBOOT CURSOR 1. GUN MENU You can adjust GUN unit in GUN ADJUST mode. GUN ADJUST X Gun Adjust 1. Enter TEST MENU and select GUN ADJUST. 2. Shoot center mark only with gun sight. 3. If you need more accuracy, try again. 4. Press START button to save Gun accuracy and enter GUN TEST mode, press START button again to go back to Main menu. You can test accuracy in GUN TEST mode. SHOOT CENTER MARK ONLY TO ADJUST PRESS START BUTTON TO GUN TEST GUN TEST Gun Test 1. At Gun Adjust screen, press START button to go to test mode. 2. Shoot all around the screen to see Gun's accuracy. 3. Press START button to go back to Main menu. X PRESS START BUTTON TO EXIT 2. COLOR TEST Use this screen to check the color of monitor. The color blocks in the center should be four bands (Red, Green, Blue and White from top to bottom), each with a color scale from dark to bright, left to right. If the screen does not match this description, adjust the Monitor as described in the Monitor's manual. * Press the START button to exit and go back to the TEST MENU screen. COLOR TEST RED GREEN BLUE WHITE PRESS START BUTTON TO EXIT 9 3. CROSS HATCH Use this screen to check the size of picture. The CROSS HATCH test pattern has a White grid on a Black background. Check following: - The grid line should be straight, and the lines should not have excessive pincushion or barrel distortion. - "Out"line of grid line is the same size as "Out"line of game screen. So, "Out" line should be able to be seen with no overflow of grid lines on screen. If these are not as above, adjust the Monitor as described in the Monitor's manual. * You can exit and go back to the TEST MENU screen by press START button. CROSS HATCH PRESS START BUTTON TO EXIT 4. I/O TEST Use this screen to check the switches in this game. To check the functioning of each switch, activate it and watch the corresponding OFF letters change to ON. If the ON and OFF letters do not appear correctly, check the Harness connections and Switches. * Press START button and Gun trigger simultaneously to exit. I/O TEST COIN A COIN B SERVICE TEST 1P GUN START PUMP TRIGGER : OFF : OFF : OFF : OFF 2P GUN START PUMP TRIGGER : OFF : OFF : OFF : OFF : OFF : OFF PRESS START & GUN TRIGGER TO EXIT 5. SOUND TEST Use this screen to check all game sounds. Choose a sound with the START buttons. (Hunter 1 = forward, Hunter 2 = Back) Then pull the TRIGGER. You can check each sound in this game. * Press START button and Gun trigger simultaneously to exit. SOUND TEST SOUND CODE 000 BLAK_SHOT PRESS START BUTTON TO CHOOSE PRESS GUN TRIGGER TO PLAY PRESS START & GUN TRIGGER TO EXIT 6. MEMORY TEST Use this screen to check RAM and ROM on the Main P.C.B. The Main P.C.B. will automatically check them when you enter this screen. If there are no problems, the word OK will appear on screen. If you get the word ERROR, check the mounting of RAMs or ROMs on the Main P.C.B. and if ERROR reappears, it needs to be replaced. MEMORY TEST WORK RAM : OK BACKUP RAM : OK ROM (U06) ROM (U07) : OK : OK * This mode will automatically exit after testing is finished. 10 7. OPTIONAL SETTING HIGH SCORE CLEAR If you desire to clear HIGH SCORE data, do the following. HOW TO SET UP 1. Enter TEST MENU and select OPTIONAL SETTING. 2. Press START BUTTON to choose HIGH SCORE CLEAR. 3. Select YES by pressing START BUTTON and pressing GUN TRIGGER to clear HIGH SCORE data. 4. The screen will return to previous screen automatically after clearing HIGH SCORE data. OPTIONAL SETTING 1. HIGH SCORE CLEAR 2. GUN ADJUST DEFAULT 3. RETURN TO TEST MENU PRESS START BUTTON TO CHOOSE PRESS GUN TRIGGER TO SELECT HIGH SCORE CLEAR ARE YOU SURE YOU WANT TO CLEAR HIGH SCORE? YES NO PRESS START BUTTON TO CHOOSE PRESS GUN TRIGGER TO SELECT NOTE: Do not proceed if Gun test is accurate. GUN DATA DEFAULT If you have problem with Gun sighting , you may have to clear the Gun data. After clearing Gun data, the game will be reset to factory default setting. See the following for how to clear saved data. 1. Enter TEST MENU and select OPTIONAL SETTING. 2. Press START BUTTON to choose GUN ADJUST DEFAULT. 3. Select YES by pressing START BUTTON and pressing GUN TRIGGER to clear Gun data. 4. The screen will return to previous screen automatically after clearing Gun data. Use this screen to go back to normal game mode. After selecting this function, the game will automatically take you to the normal game screen. Make sure to turn OFF "DIP SWITCH 1, #8" or you will return to test mode upon powering on. GUN ADJUST DEFAULT ARE YOU SURE YOU WANT TO SET GUN ADJUST DEFAULT? YES NO PRESS START BUTTON TO CHOOSE PRESS GUN TRIGGER TO SELECT 8. REBOOT Returning to GAME MODE You can return to normal game mode by doi ...