User manual SAMPO PME-42V3

PLASMA DISPLAY USER MANUAL MODEL: PME-42V3 TABLE OF CONTENTS PAGE 1 2 3 FCC CLASS B STATEMENT... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... Wichtige Sicherheitshinweise... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .... . IMPORTANT SAFETY INSTRUCTIONS... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 1 2 3-4 4 BACK PANEL CONNECTIONS... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. 5-6 5 REMOTE CONTROL FUNCTIONS... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 7-9 6 BATTERY IN REMOTE CONTROL... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 10 7 FRONT PANEL AND CONNECTIONS... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 11 8 9 ON SCREEN DISPLAY MENU SETTINGS ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . POWER MANAGEMENT FUNCTION... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 12-14 15 10 TROUBLE SHOOTING... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. 16 11 SPECIFICATIONS (Preliminary)... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 17-19 12 INSTALLATION METHOD FOR WALL MOUNTING... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. 20-21 FCC CLASS A STATEMENT IMPORTANT: The equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in strict accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ¡EReorient or relocate the receiving antenna. ¡EIncrease the separation between the equipment and the receiver. ¡EConnect the equipment into an outlet on a circuit different from that to which the receiver is connected. ¡EConsult the dealer or an experienced radio/TV technician for help. Shielded interconnected cables and shield power cords must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment and invalidate the warranty. CANADIAN COMPLIANCE STATEMENT: This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la Classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Warning: To prevent screen damage do not allow a still image to be displayed on screen for more than 1 hour. Also, to preserve screen quality it is best to view 4:3 images in 16:9 format and to make sure that the on screen display is not left on for extended periods of time. -1- Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Umeine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Verletzungen hervorrufen. Verwenden Sie nur sichere Standorte und beachten Sie die Aufstellhinweise des Herstellers. 7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor Überhitzung schützt. Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden. 8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte. 9. Die Netzanschlußsteckdose muß aus Gründen der elektrischen Sicherheit einen Schutzleiterkontakt haben. 10. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden. 11. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten. 12. Wird das Gerät uber einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen.Somit wird im Falle einer Überspannung eine Beschädigung vermieden. 13. Durch die Lüftungsäffnungen dürfen niemals Gegenstände oder Flussigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen. 14. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden. 15. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu überprufen: ¡ENetzkabel oder Netzstecker sind beschädigt. ¡EFlussigkeit ist in das Gerät eingedrungen. ¡EDas Gerät war Feuchtigkeit ausgesetzt. ¡EWenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. ¡EDas Gerät ist gefallen und/oder das Gehäuse ist beschädigt. ¡EWenn das Gerät deutliche Anzeichen eines Defektes aufweist. 16. Bei Reparaturen dürfen nur Orginalersatzteile bzw. Den Orginalteilen entsprechende Teile verwendet werden. Der Einsatz von ungeeigneten Ersatzteilen kann eine weitere Beschädigung hervorrufen. 17. Wenden Sie sich mit allen Fragen die Service und Reparatur betreffen an Ihren Servicepartner. Somit stellen Sie die Betriebssicherheit des Gerätes sicher. -2- IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE TV/MONITOR'S COVER. NO USER SERVICEABLE PARTS ARE INSIDE THE UNIT. PLEASE REFER SERVICING TO QUALIFIED PERSONNEL. WARNING: 1. To prevent fire or shock hazard, do not expose this monitor to rain or moisture. PRECAUTIONS: 1. Keep monitor away from excessive dust, high temperatures, moisture or direct sunlight. 2. Use in a well-ventilated area and do not cover ventilation openings. 3. Unauthorized modification this equipment or usage of an unshielded connecting cable may cause excessive interference. 4. When the monitor is not in use, disconnect it from the electric outlet. 5. If the picture displayed is in any way abnormal, turn off the unit and disconnect it from the electric outlet. Verify your signal wire connections and reconnect the TV to the electric outlet. 6. Read all instructions. 7. Follow all warnings and instructions marked on the product. 8. Disconnect from the electric outlet before cleaning. Do not use liquid or aerosol cleaners. Use only a slightly damp cloth for cleaning. 9. Do not use this product near water. 10. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage. 11. The ventilation slots located on the back of the cabinet are for proper heat dissipation. To ensure Do reliable operation of the unit and to protect it from overheating, do not block or cover the openings. not place the unit on a bed, sofa, rug, or other similar surfaces. Never place the unit near or over a radiator or heat source. Do not install unit in an enclosed area unless proper ventilation is provided. -3- IMPORTANT SAFETY INSTRUCTIONS 12. The unit should be operated from the type of power source indicated on the label. If the type of available power is unknown, consult your dealer or local power company. 13. The unit is equipped with a 3-pin grounded plug. The plug will only fit into a grounded power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician. Do not alter the plug; this will defeat the safety feature. 14. Do not rest objects on the power cord. 15. Avoid placing the power cord near high traffic areas. 16. If an extension cord is used, make sure that the total ampere ratings of the products connected to the extension cord do not exceed the extension cord ampere rating. Also make sure that the total amperes of all products connected to the main outlet do not exceed 15 amperes. 17. Do not attempt to service unit yourself. Opening or removing the cover may result in exposure to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. 18. Disconnect the unit from the m supply and refer servicing to qualified service personnel under the ain following conditions: ¡EPower cord or plug is damaged or frayed. ¡ELiquid has been spilled into the product. ¡EUnit has been exposed to water or moisture. ¡EUnit does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions, improper adjustment of other controls may result in damage which often requires extensive work by a qualified technician to restore the unit to normal operation. ¡EUnit has been dropped or the cabinet has been damaged. ¡E exhibits a distinct change in performance, indicating a need for service. Unit -4- BACK PANEL CONNECTIONS BUTTON-REAR PANEL ¬ MAIN POWER L R ² ± 12 OUT 13 RGB OUT ´ RGB IN USB POWER IN RS 232 H 14 V Y Y G CB PB B CR PR R µ ® ¯ DVI IN ° R AUDIO IN VIDEO IN 11 COMPONENT VIDEO INPUT ³ RGB IN S-VIDEO COMPOSITE INPUT VIDEO ~ ~ ~ ~ ~ Connecting to video equipment ~ Connecting to PC ~ ~~ Connecting to video equipment Connecting to PC AC 90~260V 50/60Hz Connecting to Audio equipment Connecting to PC 1 MAIN POWER: The AC main power switch. POWER IN: This terminal is for AC power cord. S-VIDEO: This terminal is for S-VIDEO signal cable, used with S-VIDEO equipment. COMPOSITE IN: These terminals are for composite video signals, used with video equipment with composite video outputs. VIDEO AUDIO IN: Use these audio input terminals for using audio signals accompanying the video signal when the plasma display panel is in COMPOSITE/S-VIDEO/YCBCR mode. RGB AUDIO IN: Use these audio input terminals for using audio signals accompanying the RGB video signal when the plasma display panel is in RGB/BNC RGB/YPBPR/DVI mode. AUDIO OUT: These terminals output sound signals. The audio output will change according to the mode currently displayed by the plasma display panel. RGB IN: This terminal is for RGB analog signals for use with IBM PCs and compatibles. RGB OUT: This terminal is for RGB signal output so that you can "daisy-chain" another RGB display device to the same RGB analog signal currently used by the plasma display panel. DVI IN: This terminal is for connecting to PC's equipped with a digital video interface. 2 3 4 5 6 7 8 9 10 11 RS232 IN: This terminal is for control system signal, for use with IBM PCs and compatibles. -5- BACK PANEL CONNECTIONS 12 USB: This terminal is for control system signal, for use with IBM PCs and compatibles. COMPONENT VIDEO IN: This terminal is a multi-functional terminal which can receive high-definition component video signals (YPBPR), standard component video signals (YCBCR), and RGB analog signals. YPBPR: Use this terminal to connect high-definition, progressive scan component video signals from progressive scan video equipment such as progressive scan DVD players and high end HDTV decoders. YCBCR: Terminal is for standard component video input (YCBCR) video signals BNC RGB: Use terminal for RGB video. Must use in conjunction with BNC H.V IN. BNC H.V IN: This terminal is for RGB signal, H-sync and V-sync. 13 14 Note: 1. When using component video inputs, only one signal input can be used at any one time. The plasma display panel will automatically detect which signal input is used. -6- REMOTE CONTROL FUNCTIONS 1 10 11 5 6 4 3 2 9 7 8 -7- REMOTE CONTROL FUNCTIONS The plasma display panel features advanced on-screen adjustments for optimal viewing. You can access these features by using the controls located on the plasma display panel. 1. POWER Pressing the POWER button turns on the unit. When power is on, the green POWER LED illuminates. When power is off, the unit switches to standby mode illuminating the red STANDBY LED. 2. - VOL + Use the VOL -/+ buttons adjusts the volume of the plasma display panel. 3. MUTE Use MUTE button to quickly turn off the sound through the plasma display panel' s internal speakers. Once pushed, the on-screen display will indicate that the mute function is enabled. To disable the mute function, press the button again. The on-screen display will disappear and sound will be restored from the speakers. Press this button to set the display to the factory pre-set default value. 4. RECALL 5. INPUT Press button to select the video signal source to display. Each time the input button is pressed, the on-screen display will cycle between: ¡÷ RGB¡÷DVI¡÷AV¡÷S-VIDEO¡÷YPBPR(YCBCR)¡÷BNC RGB Note: When YPBPR mode is selected, the plasma display panel will automatically detect whether the input signal is standard definition component video (YCBCR) or high-definition progressive component video (YPBPR). 6. DISPLAY Press this button to turn-on or off the On-Screen Display menu. 7. AV S-VIDEO YPBPR Press these buttons to directly select the video signal source to display. BNC-RGB RGB DVI -8- REMOTE CONTROL FUNCTIONS 8. ON OFF Press these buttons to directly turn the power on or power off. POWER 9. ¡ÐMENU¡Ï To display the monitor' on-screen display, press MENU +/- button. s 10.¡ÐADJ¡Ï Use the ADJ +/- button for setting plasma display panel settings. 11. WIDE This button toggles between the various Display modes available. When the plasma display panel is in RGB, DVI, BNC RGB mode, the following choices are available: ¡÷16:9¡÷ 4:3 When the plasma display panel is in AV, S-VIDEO, or YCBCR, YPBPR modes, the following choices are available: ¡÷16:9¡÷ZOOM1 4:3¡öZOOM2 When plasma display panel is RGB, DVI, or BNC RGB modes running at 31K/60HZ, the following choices are available: ¡÷16:9¡÷W 4:3¡÷W 16:9¡÷4:3 When PC resolution is set to 640¡Ñ480 at 60Hz you can choose either 16:9 or 4:3 by pressing the "WIDE" button on the remote. When PC resolution is set to 852¡Ñ480 at 60Hz, you can choose either w4:3 or w16:9 by pressing the "WIDE" button on the remote. -9- BATTERY IN REMOTE CONTROL Open the cover on the back of the remote and insert two R03/AAA/SUM-4 batteries. Be sure the polarity is correct. Replace the cover NOTES: To avoid damage from possible battery leakage, remove the batteries for extended unused periods. Be sure that there are no obstructions between the Remote Control and the Monitor. Operating range is specified for normal use. The shorter the distance between the Remote Control and the Monitor, the narrower the angle within which the Remote Control can operate the Monitor. -10- FRONT PANEL AND CONNECTIONS Front View VOL- (ADJ -) VOL+ (ADJ +) MENU - POWER Button POWER LED INPUT MENU + 1. POWER Pressing the POWER button turns on the unit. When power is on, the green POWER LED illuminates. When power is off, the unit switches to standby mode illuminating the red STANDBY LED. 2. ¡ÐMENU¡Ï To display the monitor' on-screen display, press MENU +/- button. s 3. ADJ ¡Ð ¡Ï VOL Use the VOL -/+ buttons to adjust the volume of the plasma display panel. These buttons also function as the ADJ -/+ buttons for setting plasma display panel settings. 4. INPUT SELECT Press button to select the video signal source to display. Each time the input button is pressed, the on-screen display will cycle between: ¡÷ RGB¡÷DVI¡÷AV¡÷S-VIDEO¡÷YPBPR(YCBCR)¡÷BNC RGB Note: When YPBPR mode is selected, the plasma display panel will automatically detect whether the input signal is standard definition component video (YCBCR) or high-definition progressive component video (YPBPR). -11- ON SCREEN DISPLAY MENU SETTINGS The plasma display panel features advanced on-screen adjustments for optimal viewing. You can access these features by using the MENU +/- buttons located on the plasma display panel (accessible by pressing the center of the door) or by using the remote control. When the MENU +/- buttons are pressed, various On-Screen Display menus are displayed depending on the input source selected. RGB/BNC RGB/DVI On Screen Display Menu RGB BRIGHTNESS M:01 FH:31KHz FV: 60Hz AV/S-VIDEO/YCBCR On Screen Display Menu RGB BRIGHTNESS M:AV FH:15KHz FV:60Hz YPBPR On Screen Display Menu RGB BRIGHTNESS M:YP FH:31KHz FV:60Hz -12- ON SCREEN DISPLAY MENU SETTINGS BRIGHTNESS: Select icon to adjust the overall picture brightness (image black level). Set the brightness so that the dark areas of the monitor remain black. Press the ADJ - button to decrease brightness. Press the ADJ + button to increase brightness. This setting is available to all video signal inputs CONTRAST: Select icon to adjust the contrast (image white level). Contrast is the difference in brightness between the dark and light parts of the displayed image. Press the ADJ- button to decrease contrast. Press the ADJ + button to increase contrast. This setting is available to all video signal inputs. V-SIZE (Vertical Size): Select icon to adjust the vertical size of the displayed image. Press the ADJ - button to decrease V-Size. Press the ADJ + button to increase V-Size. V-CENTER (Vertical Position): Select icon to adjust the vertical position of the displayed image. Press the ADJ- button to decrease V-Position. Press the ADJ+ button to increase V-Position. H-WIDTH (Horizontal Size): Select icon to adjust the horizontal size of the displayed image. Press the ADJ- button to decrease H-Width. Press the ADJ + button to increase H-Width. H-PHASE (Horizontal Position):. Select icon to adjust the horizontal position of the displayed image. Press the ADJ- button to decrease H-Phase. Press the ADJ + button to increase H-Phase. CLOCK PHASE: Select this icon to adjust the sampling clock of the displayed image. Press the ADJ- button to decrease phase clock. Press ADJ+ button to increase phase clock. ¡° In DVI mode, clock phase is not available. DPMS: Select this icon to change the timing of auto power off. DPMS uses monitor power management signal to automatically reduce monitor power consumption. While power is on, if there is no signal input at the pre-set time, the power management function will come on automatically, and the screen of display will automatically shut-own and enter stand-by status. The waiting timing of the signal can be set from 1 min. to 5 min. The power saving function can also be switched off. (Power saver is off in factory setting). Please press ADJ key to move selection to next item as shown below ; OFF 1 2 3 4 5 -13- ON SCREEN DISPLAY MENU SETTINGS COLOR: Select icon to adjust the color of the displayed image. Press the ADJ ­ button to decrease color. Press the ADJ + button to increase color. TINT: Select icon to adjust the tint of the displayed image. Press the ADJ + button to increase the level of green in the image. Press the ADJ button to increase the level of red in the image. ¡° IN YCBCR mode, TINT is not available. SHARPNESS: Select icon to adjust the sharpness of the displayed image. Press the ADJ - button to decrease sharpness. Press the ADJ + button to increase sharpness. WHITE BALANCE: Select this icon to adjust color temperature setting between: Cool, Warm, or Hot select 1,2 or 3 as below. 1: Cool: Tend to blue tone. 2: Warm: Standard. 3: Hot : Tend to red. RGB -14- POWER MANAGEMENT FUNCTION The following is a description of the power states and the power consumed in each state: MODE on power saving power saving power saving NOTE: l l The power management function requires TTL horizontal and vertical sync. Power saving is invalid if display is in AV, YCBCR, YPBPR mode. LED green yellow yellow yellow H-SYNC pulse no pulse Pulse no pulse V-SYNC Pulse Pulse no pulse no pulse VIDEO active blanked blanked blanked POWER CONSUMPTION normal <5W <5W <5W As an ENERGY STAR ® partner, Sampo Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. -15- TROUBLE SHOOTING The following list represents possible anomalies you may encounter and the methods for remedying them Please refer to this checklist prior to contacting a service representative. Trouble condition No picture Cause 1.Power cord disconnected? 2.Power switch on? 3.Signal cable properly connected? 4. Monitor in power save mode? 1.Signal cable properly connected? 1.Signal cable properly connected? 2.Input signal outside of the required frequency range? Remedy 1.Connect power cord. 2.Turn the power switch on. 3.Connect the signal properly. 4.Press any key on your computer. 1.Connect signal cable properly. 1.Connect signal cable properly. 2.Input signals, which are within the frequency, range. Adjust brightness and contrast. 1.Adjust to desired size. 2.Adjust to desired size. 1.Verify the direction of input source. 2.Verify whether the cable was connected properly. Color is abnormal Picture runs Display image is too Brightness and contrast at minimum? dark Display image is too 1.Horizontal control needs adjusting? large or small 2.Vertical control needs adjusting? Has sound picture but no 1.Input source direction changed? 2. Input source properly connected? Note: Audio I/P has 2 sources, One is for AV/S-VIDEO/YCBCR mode. The other is for YPBPR/BNC RGB/RGB/DVI mode. Has picture sound but no 1.Problem with input source? 2.Volume adjusted to min? 3.Audio cable not connected? 4.Non-integrate signal pronounced? Note: Audio I/P has 2 sources, One is for AV/S-VIDEO/YCBCR mode. The other is for YPBPR/BNC RGB/RGB/DVI mode. 1.Verify the direction of input source. 2.Adjust the volume properly. 3.Connect the audio cable properly. 4.Try other channels. Remote control is not 1.Battery is OK? functioning. 2.Is it because of outside interference? 1.Change the battery. 2.Pull the AC Cord out for 10 seconds. Then plug it in again and turn the power on. -16- SPECIFICATIONS (Preliminary) 1. Display panel a. b. c. d. e. 2. Screen size Aspect ratio Number of pixels Pixel pitch Luminance 16:9 wide 852(Horizontal, RGB Trio ) X 480(Vertical)pixels 1.08mm X 1.08mm 350cd/m2,at APL13% Power a. b. c. d. Input voltage Input current Inrush current Power consumption 100 ~ 240 Vac , 50 / 60 Hz 3.3A 60 A p-p/20ms max 340¡Ó10% Watt ( at 110Vac/color bar pattern) 5 watt Max (at 110Vac) 15 pin dual D-SUB and RCA JACK and S-terminal 24 pin DVI connector 9 pin D-SUB BNC for RGB or YPBPR or YCBCR e. Stand-by & DPMS 3. Connector type 4. AV/S-VIDEO signal a. b. c. d. Type Polarity Amplitude Frequency Analog Positive AV: 1Vp-p S-VIDEO: =1Vp-p H: 15.734KHz V: 60Hz(NTSC) H: 15.625KHz V: 50Hz(PAL) 75 ohm C=0.286Vp-p e. Input impedance 5. YCBCR or YPBPR signal a. Type b. Polarity c. Amplitude d. Frequency YCBCR YPBPR: HDTV Analog Positive AV: 1vp-p (with sync) Priorites: Y: 1Vp-p c: 0.286Vp-p H: 15.734KHz V: 60Hz (NTSC) H: 15.625KHz V: 50Hz (PAL) 1. 31KHz/60Hz (480P) 2. 45KHz/60Hz (720P) 3. 33KHz/60Hz(1080I) 6. BNC RGB/RGB signal a. Type b. Polarity c. Amplitude d. Frequency TTL Positive or negative RGB: 0.7Vp-p H: support to 31K~91KHz V: support to 50~85Hz -17- SPECIFICATIONS (Preliminary) 7. DVI signal a. Type b. Polarity c. Frequency Digital Positive or negative H: support to 31~63KHz V: support to 50~85Hz 8. Audio signal a. input level b. practical max Horizontal size (Standard) Vertical size (Standard) Dimensions Width Height Depth Analog 500mV rms/more then 22Kohm 5W+5W max (at 10% THD max) 920¡Ó8 mm (for mode 1¡ã23) 518¡Ó8 mm (for mode 1¡ã23) Without / Stand 1050mm 661 mm 127.5mm With / Stand 1050mm 719mm 275 mm 9. 10. 11. Package dimensions Width Height Depth 1145 mm 790 mm 370 mm 12. Weight Net weight 79.4lbs/36 kgs 13. User controls Brightness, Contrast, Color, Tint, Sharpness, Vertical position, Vertical width, Horizontal position, Horizontal width, Color temperature clock phase, DPMS. 14. Operating Temperature Temperature 0~40¢J(32~105¢K) 15. Pin assignments for D-SUB connector (in / loop out) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 : : : : : RED GREEN BLUE GND GND Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 : : : : : RED GND GREEN GND BLUE GND NC GND Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 : : : : : GND SDA H-SYNC V-SYNC SCL -18- SPECIFICATIONS (Preliminary) 16. Pin assignments for 24 pin DVI connector Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 : : : : : : : : : : TMDS Data 2TMDS Data 2+ TMDS Data 2/4 Shield TMDS Data 4TMDS Data 4+ DDC Clock DDC Data Analog Vertical Sync TMDS Data 1TMDS Data 1+ Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Pin 16 Pin 17 Pin 18 Pin 19 Pin 20 : : : : : : : : : : TMDS Data 1/3 Shield TMDS Data 3TMDS Data 3+ +5V Power Ground (+5, Analog H/V Sync) Hot Plug Detect TMDS Data 0TMDS Data 0+ TMDS Data 0/5 Shield TMDS Data 5Pin 21 Pin 22 Pin 23 Pin 24 : : : : : TMDS Data 5+ TMDS Clock Shield TMDS Clock + TMDS Clock - 17. RGB / DVI for VESA standard. Mode No Resolution Refresh Rate (Hz) 60 72 75 85 56 60 72 75 85 60 70 75 85 60 75 85 50 60 60(I) 70 70 60 Horizontal Vertical Frequency Frequency (K Hz) 31.5 37.9 37.5 43.3 35.1 37.9 48.1 46.9 53.7 48.4 56.5 60.0 68.7 63.98 79.98 91.15 31.5 45.15 33.78 31.50 31.46 31.72 (Hz) 59.94 72.81 75 85.01 56.25 60.317 72.19 75 85.06 60.01 70.07 75.03 84.99 60.02 75.03 85.02 50 60 70 70 70.08 60.41 Vertical Sync Polarity (TTL) + + + + + + + + + + + Horizontal Sync Polarity (TTL) + + + + + + + + + + Dot rate 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15¡· 16¡· 19 20¡· 21¡· 22 22 23 640(VGA)¡Ñ480 640(VGA)¡Ñ480 640(VGA)¡Ñ480 640(VGA)¡Ñ480 800(SVGA)¡Ñ600 800(SVGA)¡Ñ600 800(SVGA)¡Ñ600 800(SVGA)¡Ñ600 800(SVGA)¡Ñ600 1024(XGA)¡Ñ768 1024(XGA)¡Ñ768 1024(XGA)¡Ñ768 1024(XGA)¡Ñ768 1280(SXGA)¡Ñ1024 1280(SXGA)¡Ñ1024 1280(SXGA)¡Ñ1024 640(VGA)¡Ñ480 1280(HDTV)¡Ñ720P 1920(HDTV)¡Ñ1080I 640(VGA)¡Ñ350 720(DOS)¡Ñ400 852(WGA)¡Ñ480 (MHz) 25.175 31.500 31.500 36.000 36.000 40.000 50.000 49.500 56.250 65.000 75.000 78.750 94.500 108.00 135.00 157.50 25.175 74.250 74.250 25.175 28.320 30.00 Attention ¡·: DVI is not supported. YPBPR for component Mode No 1 2 3 Resolution 640¡Ñ480P 1920¡Ñ1080I 1280¡Ñ720P Refresh Rate 60 60 60 -19- INSTALLATION METHOD FOR WALL MOUNTING Set-up steps 1. Set up the roll bars marked 1,2,3,4. 2. Put the two roll bar terminals into the wall-mounting angle. Then fix them in place with M4 size screws. They are marked 5,6,7,8. 3. Use the 3/8" driver head to fix the wall-mounting angle. The wall-mounting angle must be fixed to cement Wall. 4. Set up the wall mounting frame and set. a. Put the fixing screws in the gutter of the wall-mounting frame. b. Fix the frame with 4 M5X10 size screws. Part description A. fix roll bar B. fix roll bar C. left side of wall mounting angle D. right side of wall mounting angle E. fixing screw F. wall mounting frame and fixing screws M5X10 size G. wall mounting frame and roll bar fixing screws M4X16 size 2 PCS 2 PCS 1 PCS 1 PCS 8 PCS 4 PCS 4 PCS Note 1. The force for fixing M4X16 size screws should be 15Kg/cm. 2. The force for fixing M5X10 size screws should be 20Kg/cm. 3. The force for mounting screws should be 30Kg/cm. 4. The set must be mounted on a cement wall. -20- INSTALLATION METHOD FOR WALL MOUNTING -21-