HIGH DEFINITION DIGITAL TELEVISION 36" (34" Viewable) 16:9 PERFECTLY FLAT WIDE SCREEN 34" (32" Viewable) 4:3 SUPER FLAT TUBE 29" (27" Viewable) 4:3 SUPER FLAT TUBE USER MANUAL TABLE OF CONTENTS 1.FCC STATEMENT.... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ............... ... ... ... ... ... ... 1 2.IMPORTANT SAFETY INSTRUCTION... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 2-5 3.BACK PANEL AND CONNECTION... ... ... ... ..... ... ... ... ... ... ... ... ... ... ... ........... ... 6-7 4.LOCATION OF BUTTONS ON REMOTE CONTROL.... ... ... ... ... ... ... ... ... ... ..... ... 8 5.USING THE TV'S ADVANCED FEATURES........................................................9-15 6.USING THE MONITOR'S ADVANCED FEATURES.... ... ... ... ... ... ... ... ... ........ 16-17 7.BATTERY IN REMOTE CONTROL... ... ... ... ..... ... ... ... .... ... ... ... ... .......................18 8.FRONT PANEL AND CONNECTIONS... ... ... ... ... ... ... ... ... ... ... ... ........ ... ... ....19-21 9.ON SCREEN DISPLAY MENU SETTINGS... ... ... ... ... ... ... ... ... ... .................... 22-28 10. TROUBLE SHOOTING... ... ... ... ... .... ... ... ... ... ... ... ... ... ... .... ... ... ... ... ... .... ... 29-30 11.FREQUENCY TABLE... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..... 31-33 12.SPECIFICATIONS... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 34-3 -1- FCC CLASS B STATEMENT IMPORTANT: The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in strict accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measure: l l l l Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Shielded interconnected cables and shield power cords must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment and invalidate the warranty. CANADIAN COMPLIANCE STATEMENT: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. -1- CE (EUROPE) STATEMENT 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Umeine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Verletzungen hervorrufen. Verwenden Sie nur sichere Standorte und beachten Sie die Aufstellhinweise des Herstellers. 7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor Überhitzung schützt. Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden. 8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte. 9. Die Netzanschlußsteckdose muß aus Gründen der elektrischen Sicherheit einen Schutzleiterkontakt haben. 10. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden. 11. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten. 12. Wird das Gerät uber einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen.Somit wird im Falle einer Überspannung eine Beschädigung vermieden. 13. Durch die Lüftungsäffnungen dürfen niemals Gegenstände oder Flussigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen. 14. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden. 15. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu überprufen: l Netzkabel oder Netzstecker sind beschädigt. l Flussigkeit ist in das Gerät eingedrungen. l Das Gerät war Feuchtigkeit ausgesetzt. l Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. l Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt. l Wenn das Gerät deutliche Anzeichen eines Defektes aufweist. 16. Bei Reparaturen dürfen nur Orginalersatzteile bzw. Den Orginalteilen entsprechende Teile verwendet werden. Der Einsatz von ungeeigneten Ersatzteilen kann eine weitere Beschädigung hervorrufen. 17. Wenden Sie sich mit allen Fragen die Service und Reparatur betreffen an Ihren Servicepartner. Somit stellen Sie die Betriebssicherheit des Gerätes sicher. -2- IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE TV/MONITOR'S COVER. NO USER SERVICEABLE PARTS ARE INSIDE THE UNIT. PLEASE REFER SERVICING TO QUALIFIED PERSONNEL. WARNING: 1. To prevent fire or shock hazard, do not expose this monitor to rain to rain or moisture. 2. High voltage exists on the cathode-ray tube anode lead of this monitor. Before servicing, determine the presence of high voltage by connecting the H.V. meter between the anode of CRT cap and chassis only. PRECAUTIONS: 1. Keep monitor away from excessive dust, high temperatures, moisture or direct sunlight. 2. Use in a well-ventilated area and do not cover ventilation openings. 3. Unauthorized modification to this equipment or usage of an unshielded connecting cable may cause excessive interference. 4. If the picture displayed is in any way abnorma l, turn off the unit and disconnect it from the electric outlet. Verify your signal wire connections and reconnect the TV to the electric outlet. 5. Read all of these instructions and Save these instructions for later use. 6. Follow all warnings and instructions marked on the product. 7. Disconnect from the mains supply before cleaning. Do not use liquid or aerosol cleaners. Use only a slightly damp cloth for cleaning. 8. Do not use this product near water. 9. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage. 10. The ventilation slots located on the back of the cabinet are for proper heat dissipation. To ensure reliable operation of the unit and to protect it from overheating, do not block or cover the openings. Do not place the unit on a bed, sofa, rug, or other similar surfaces. Never place the unit near or over a radiator or heat source. Do not install unit in an enclosed area unless proper ventilation is provided. 11. The unit should be operated from the type of power source indicated on the label. If the type of available power is unknown, consult your dealer or local power company. -3- IMPORTANT SAFETY INSTRUCTIONS 12. The unit is equipped with a 3-pin grounded plug. The plug will only fit into a grounded power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician. Do not alter the plug; this will defeat the safety feature. 13. Do not rest objects on the power cord. 14. Avoid placing the power cord near high traffic areas. 15. If an extension cord is used, make sure that the total ampere ratings of the products connected to the extension cord do not exceed the extension cord ampere rating. Also make sure that the total amperes of all products connected to the main outlet does not exceed 15 amperes. 16. Never push objects of any kind into the unit through its ventilation slots. This may result in dangerous voltage points or electrical shorting of parts, resulting in fire or electric shock. Never spill liquid of any kind on the unit. 17. Do not attempt to service unit yourself. Opening or removing the cover may result in exposure to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. 18. Disconnect the unit from the main supply and refer servicing to qualified service personnel under the following conditions: l l l l Power cord or plug is damaged or frayed. Liquid has been spilled into the product. Unit has been exposed to water or moisture. Uit does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions, improper adjustment of other controls may result in damage which often requires extensive work by a qualified technician to restore the unit to normal operation. l l Unit has been dropped or the cabinet has been damaged. Unit exhibits a distinct change in performance, indicating a need for service. -4- BACK PANEL CONNECTIONS VTR/LD DVD PLAYER RF µ VIDEO IN AUDIO IN R AV 1 R- AUDIO- L Y CB ´ CR R L COMPONENT ... S-VIDEO 3 AV ² L OUT R L Y PB ^ PR R L ± RGB IN L AUDIO R RGB OUT ¬ AC IN , ,, PC/NOTEBOOK SET TOP BOX OTHER RGB MONITOR · ® ¯ ° ± AC IN: This terminal is for AC power cord. RGB IN: This terminal is for RGB analog signal, use with IBM PC and other compatibles. RGB OUT: Terminal for RGB signal output so that you can attach another display monitor to display the same RGB analog signal that your monitor is currently displaying. RGB AUDIO IN: These terminals are for sound signal when monitor is in RGB mode. AV IN: Terminals are for video and stereo sound signals, used with video equipment with composite video outputs. S-VIDEO 3: Terminals are for S-VIDEO and stereo sound signals, used with video equipment with Composite video outputs. Æ AV OUT: Terminals can output composite video and sound signals that the monitor is using. AV OUT only supplies composite video signals. Y/PB/PR and Y/CB/CR signals are not supported. ³ Y/PB/PR: Terminal is for progressive-scan component input (Y PB PR) video signals and stereo sound signals. This is used with progressive-scan video equipment such as progressive-scan DVD players and high end HDTV decoders. É Y/CB/CR: Terminal is for standard component video input (Y/CB/CR) video signals and stereo sound signals. RF: This terminal is for connect RF antenna or cable TV box. -5- BACK PANEL CONNECTIONS NOTE: l l l Before connecting any cables, refer to the safety instructions at the beginning of this manual and make sure the unit and the video equipment are both switched off. Be sure to lug the AC power cord to a properly grounded outlet. The AV OUT terminal only supplies AV1 or AV2 composite signals and does not supply Y/PB/PR or Y/CB/CR signals. -6- REMOTE CONTROL FUNCTIONS 1 12 10 7 5 8 17 11 2 18 16 14 3 DEGAUSS DISPLAY WIDE 5 4 6 CCD RECALL WOOFER 20 9 21 15 19 3 13 AIRBLUE BACK CH FULL CABLE F SEARCH ON/OF ADD/ERASE 6 4 -7- REMOTE CONTROL FUNCTIONS This television features "Digital Vision", an advanced on-screen digital display and control system to adjust various settings within the television. These functions are accessible using the remote control for the televison's front control panels. POWER 1. Pressing the POWER button turns on the unit. When power is on, the green POWER LED illuminates. When power is off, the unit switches to standby mode illuminating the red STANDBY LED. 2. INPUT SELECT Press button to select the source signal to display. Each time the input button is pressed, the on-screen display will toggle between "TV", "AV1", "AV2", S-VIDEO 3 , "Y/CB/CR", "Y/PB/PR", and "RGB". 3. AIR CABLE Use the AIR/CABLE button to switch the tuner from receiving standard over the air broadcasts or standard cable television broadcasts. If AIR is selected, the TV can receive channels 2 to 69. If CABLE is selected, the TV can receive channels 1 to 125. 4. FULL SEARCH Use the FULL SEARCH button to automatically program the television to receive broadcasts from all available channels. When this button is pushed for 1.5 seconds, the ...