SyncMaster 192MP Index Main Page Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Remote Control Setup Connecting Your Monitor Connecting to a Computer Connecting to Other Devices Installing the Monitor Driver Automatic Manual Installing a VESA Base Folding the base / Removing the base Installing a VESA Base Adjusting Your LCD Monitor User Controls User control buttons Direct-Access Features On-Screen Display OSD Functions Screen Adjustment Animation Clips Troubleshooting Check before Calling for Service Problems and Solutions Q&A Specifications General Specifications PowerSaver Preset Timing Modes Information Service Center Terms Regulatory Natural Color For Better Display Authority Safety Instructions - Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Safety Instructions - Power When not used for extended periods of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. This may cause an electric shock or fire. Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. Failure to do so may cause an electric shock or fire. Do not connect too many extension cords or plugs to an outlet. This may cause a fire. Safety Instructions - Installation Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause injury by falling. Set down the monitor carefully. It could be damaged or broken. Do not place the monitor face down. The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. Leave a space for ventilation between the product and the wall. Poor ventilation may cause the interior temperature to rise and lead to a fire. Safety Instructions - Installation To prevent rainwater from running along the outdoor antenna cable and entering the house, be sure the outdoor portion of the cable hangs down below the point of entry. If rainwater enters the product, it may cause an electric shock or fire. If you are using an outdoor antenna, be sure to put sufficient distance between your antenna and the electrical wires nearby so that they would not come in contact with each other in case the antenna is knocked over by strong wind. A knocked-over antenna may cause injury or an electric shock. Safety Instructions - Cleaning When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric. Do not spray water or detergent directly on the monitor. This may cause damage, electric shock or a fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire. When you remove batteries from the remote, be careful that they are not swallowed by children. Keep batteries out of the reach of children. If swallowed, see a doctor immediately. When replacing batteries, place the batteries in the correct +/- polarity position as indicated on battery holder. Incorrect polarity may cause a battery to break or leak and could lead to a fire, injury, or contamination (damage). Use only specified standard batteries. Do not use new and used batteries together. may cause a battery to break or leak and could lead to a fire, injury, or contamination (damage). Do not set a glass of water, chemicals or any small metal objects on the monitor. This may cause damage, electric shock or a fire. If a foreign substance gets into the monitor, disconnect the plug and then contact a service center. Contact a Service Center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or a fire. Safety Instructions - Other Do not remove cover (or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or fire. Be careful not to let water drip into the monitor or expose the monitor to moisture. This may cause malfunction, an electric shock or a fire. Especially avoid operating the monitor near water or outdoors where it could be exposed to snow or rain. If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. The monitor may malfunction, causing an electric shock or a fire. Then contact the Service Center. Keep the power off when there is thunder and lightening outside, or let the monitor remain unused for an extended period of time. The monitor may malfunction, causing an electric shock or a fire. Do not try to move the monitor by pulling on the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable. Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Do not place any heavy objects on the monitor. This may cause malfunction, an electric shock or a fire. Do not place water containers, chemical products or small metal objects on the monitor. This may cause malfunction, an electric shock or a fire. If a foreign substance enters the monitor, unplug the power cord and contact the Service Center. Do not use or store inflammable substances near the monitor. This may cause an explosion or fire. Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury. Do not insert metal objects such as utensils, wire or drill bits, or things that catch fire easily, such as pieces of paper or matches, into the vents or the headphone or A/V ports on the monitor. This may cause malfunction, an electric shock or a fire. Always contact the Service Center if foreign substances/objects enter into the monitor. If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time. Be careful when adjusting the stand angle. Applying too much force may cause the monitor topple over or fall, resulting in injury. Your hand or finger(s) may get caught between the monitor and the stand, causing injury. Adjust the resolution and frequency to the levels appropriate for the model. Inappropriate resolution may cause undesirable picture quality. 19 inch - 1280 X 1024 Be careful that adapter should not be in contact with water and therefore not be wet. This may cause malfunction, an electric shock or a fire. Do not use adaptor by the waterside or outside particularly when it rains or snows. Be careful that adaptor should not be wet while cleaning floor with water. Keep all power adaptors apart. Possible fire hazard. Keep power adaptor away from any other heat source. Possible fire hazard. Remove and discard vinyl bag from power adaptor before use. Possible fire hazard. Always keep power adaptor in well-ventilated area. Keep the volume at a proper level when you use the headphones. Excessively loud volume levels may damage hearing. Keep a proper distance between your eyes and the monitor screen. Sitting too close to the monitor on a continuous basis may damage eyesight. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not use the monitor where it can be exposed to strong vibrations. Exposure to strong vibrations can be a fire hazard and shorten the life of the monitor. When moving the monitor, turn the power switch off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connecting to other devices, are disconnected before moving the monitor. Failure to disconnect a cable may damage it and lead to a fire or an electric shock. Introduction - Unpacking Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide and Natural Color/ Driver Installation CD Power Cord Monitor Quick Setup Guide Signal Cable(15 pin D-Sub) Warranty Card (Not available in all locations) DC Adapter Audio Cable Remote Control Batteries (AAA X 2) Option DVI cable Contact a local dealer or Samsung call center to buy optional items. Introduction - Front For detailed information concerning the monitor functions, refer to User Controls under Adjusting Your Monitor. The monitor's front configuration may vary slightly depending on the monitor model. 1. Menu 2. Exit / Auto 3. Enter 4. Source 5. PIP 6. MagicBrightTM 7. Up-Down / Channel 8. Left-Right / Volume 9. Power / Power indicator 10. Remote Control Sensor PIP(Picture in Picture)? Feature allowing one program to be viewed on the entire screen while one or more programs play in small windows superimposed over the base program. Introduction - Rear For detailed information concerning cable connections, refer to Connecting Cables under Setup. The monitor's rear configuration may vary slightly depending on the monitor model. A. Power Connection Terminal (14V DC) This product may be used with 90 ~ 264. (Voltage is automatically adjusted by the power adaptor.) Connect the power source plug when all Connecting Your Montior. B. PC Connection Terminal 1. Computer Connection Terminal (DVI) 2. Computer Connection Terminal (15 Pin D-SUB) 3. Audio Connection Terminal (Audio (ST)) B. DVD/DTV Connection Terminal 1. DVD/DTV component(Y, Pb, Pr) terminal 2. DVD/DTV left / right audio connection terminal (L/R) 3. TV Connection Terminal D. AV Connection Terminal 1. Headphone connection terminal 2. Audio L / R, Video connection terminal 3. S-Video connection terminal Introduction - Remote Control For detailed information of the Remote Control Unit functions, refer to Adjusting Your Monitor > User Controls > User Control Buttons > Remote Control buttons. The remote control's configuration may vary slightly depending on the monitor model. The Remote control may function within a range of 0.23 to 33 feet (7cm to 10m) and 30 degrees to the left and right of the monitor's Remote Control Reception sensor. Button Names | Replacing Batteries | Usage 1. Button Names 1. POWER 2. Channel 3. +100 4. VOL 5. MUTE 6. AUTO 7. MENU 8. ENTER 9. PRE-CH 10. CH 11. SOURCE 12. INFO 13. EXIT 14. Up-Down Left-Right Buttons 15. P.MODE, M/B (MagicBrightTM) 16. STILL 17. S.MODE 18. MTS 19. PIP 20. SOURCE 21. SIZE 22. POSITION 2. Replacing Batteries 1. Slide out the cover pressing part marked . 2. Insert the batteries matching their polarities (+, -). 3. Slide in the cover. Setup - Connecting Your Monitor Connecting to a Computer Connecting to other devices Turn on your computer and monitor. If your monitor displays an image, installation is complete. The configuration at the back of the monitor may vary from product to product. 1. Connecting to a Computer 1. Connect the power cord to the DC adapter and connect the adapter jack to the DC POWER port on the back of your monitor. Connect the signal cable to the PC Connecting Terminal on your computer. There are 2 ways to connect the signal cable to your monitor. Choose one of the followings : 2-1. Using the D-sub (Analog) connector on the Video card. Connect the signal cable to the 15 pin D-sub Port on the back of your monitor. 2. 2-2. Using the DVI (Digital) connector on the Video card. Connect the DVI Cable(DVI-D + DVI-D) to the DVI Port on the back of your Monitor. 3. Connect the audio cable for your monitor to the audio port on the back of your computer. 4. Connect the power cord insert a plug in a ...