SyncMaster 192B/192T User's Manual Index Main Page On-Screen Display Safety Instructions Notational Power Installation Cleaning Other Troubleshooting Check List Q&A Self-Test Feature Check Introduction Unpacking Front Rear Specifications General Specifications PowerSaver Preset Display Modes Setup Connecting Your Monitor Installing the Monitor Driver -- Automatic -- Manual Information Service Terms Regulatory Natural Color For Better Display Authority User's Manual Safety Instructions Notational Warning/Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Notation Conventions Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock User's Manual Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. · Do not use a damaged or loose plug. · This may cause an electric shock or fire. · Do not pull the plug out by the wire nor touch the plug with wet hands. · This may cause an electric shock or fire. · Use only a properly grounded plug and recepticle. · An improper ground may cause electric shock or equipment damage · Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. · Failure to do so may cause an electric shock or fire. User's Manual Safety Instructions Power · Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. · Failure to do so may cause an electric shock or fire. · Do not connect too many extension cords or plugs to an outlet. · This may cause a fire. User's Manual Safety Instructions Installation · Do not cover the vents on the monitor cabinet. · Bad ventilation may cause a breakdown or fire. · Put your monitor in a location with low humidity and a minimum of dust. · An electric shock or fire could result inside the monitor. · Do not drop the monitor when moving it. · This may cause damage to the product or human body. · Place the monitor on a flat and stable surface. · The monitor can cause injury by falling. · Set down the monitor carefully. · It could be damaged or broken. User's Manual Safety Instructions Installation · Do not place the monitor face down. · The TFT-LCD surface may be damaged. User's Manual Safety Instructions Clean When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric. · Do not spray detergent directly on the monitor. · Use the recommended detergent with a smooth cloth. · If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. · A dirty connector can cause an electric shock or fire · Do not set a glass of water, chemicals or any small metal objects on the monitor. · · This may cause damage, electric shock or a fire. If a foreign substance gets into the monitor, disconnect the plug and then contact a service center. User's Manual Safety Instructions Other · Do not remove cover(or back). No user serviceable parts inside. · · This may cause an electric shock or a fire. Refer servicing to qualified service personnel. · If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. · This may cause an electric shock or a fire. · Do not place any heavy objects on the monitor. · This may cause an electric shock or a fire. · For each hour of looking at the monitor, you should let your eyes rest for 5 minutes. · This will reduce eye fatigue. · Do not use or store inflammable substances near the monitor. · This may cause an explosion or fire. User's Manual Safety Instructions Other · Do not try to move the monitor by pulling on the wire or · This may cause a breakdown, electric shock or a fire due to damage to the cable. · Do not move the monitor right or left by pulling only the wire or the signal cable. · This may cause a breakdown, electric shock or a fire due to damage to the cable. · Never insert anything metallic into the monitor openings. · This may cause an electric shock, fire or injury. User's Manual Introduction Unpacking (SyncMaster 192B) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking D-Sub Cable Quick Setup Guide Power Cord Warranty Card (Not available in all locations) Monitor User's Guide and Driver Installation CD DC-Adapter VESA Mounting Bracket For Multimedia model (Option) Multimedia Speaker Stand Sound Cable User's Manual Introduction (SyncMaster 192T) Unpacking Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking D-Sub Cable Quick Setup Guide DVI Cable (Option) Warranty Card (Not available in all locations) Power Cord Monitor User's Guide and Driver Installation CD DC-Adapter VESA Mounting Bracket For Multimedia model (Option) Multimedia Speaker Stand Sound Cable User's Manual Introduction (SyncMaster 192B) Front 1. 2. 3. 4. 5. Auto button Exit button Adjust buttons Menu button Power button 6. Power indicator a. MagicBright button Use this button to auto adjustment direct access. Use this button to Exit the active menu or the OSD. These buttons allow you to highlight and adjust items in the menu. Use this button to open the OSD and activate a highlighted menu item. Use this button to turn the monitor on and off.(When the power is turned on, a message appears in the center of the screen displaying the current mode -analog or digital input signal.) This light glows green during normal operation, and blinks green once as the monitor saves your adjustments. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently three different modes are available: Text, Internet, and Entertain. Each mode has its own pre-configured brightness value. You can easily select one of three settings by simply pressing MagicBright control buttons. Note: See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. User's Manual Introduction (SyncMaster 192T) Front 1. Auto button 2. Exit button Source button 3. Adjust buttons 4. Menu button 5. Power button 6. Power indicator a. MagicBright button Use this button to auto adjustment direct access. Use this button to Exit the active menu or the OSD. When push the 'Source' button, then Selects the Video signal while the OSD is off. (When the Source button is pressed to change the input mode, a message appears in the center of the screen displaying the current mode -analog or digital input signal.) Note:If you select the Digital mode, you must connect your monitor to the graphic card with a digital port using the DVI cable. These buttons allow you to highlight and adjust items in the menu. Use this button to open the OSD and activate a highlighted menu item. Use this button to turn the monitor on and off.(When the power is turned on, a message appears in the center of the screen displaying the current mode -analog or digital input signal.) This light glows green during normal operation, and blinks green once as the monitor saves your adjustments. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently three different modes are available: Text, Internet, and Entertain. Each mode has its own pre-configured brightness value. You can easily select one of three settings by simply pressing MagicBright control buttons. Note: See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. User's Manual Introduction (SyncMaster 192B) Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. Signal port Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. Note: See Connecting Your Monitor for further information regarding cable connections. User's Manual Introduction (SyncMaster 192T) Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. D-Sub port 3. DVI port Connect the DC Adapter for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. Connect the DVI Cable to the DVI Port on the back of your Monitor. Note: See Connecting Your Monitor for further information regarding cable connections. User's Manual Setup (SyncMaster 192B) 192T) Connecting Your Monitor Setup-General 1. Connect the DC Adapter for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 3. Connect the monitor to the Macintosh computer using the D-SUB connection cable. 4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adaptor. 5. Turn on your computer and monitor. If your monitor displays an image, installation is complete. User's Manual Setup Connecting Your Monitor Setup-For Multimedia model (Option) 1. 2. 3. 4. 5. PC sound connection terminal (Input) Headphone connection terminal (Output) Volume To listen in privacy,connect headphones here. Connect a sound cable from the input source (sound card,computer,CD-ROM drive). User's Manual Setup (SyncMaster 192T) Connecting Your Monitor Setup-General 1. 2-1. Connect the DC Adapter for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Using the D-sub (Analogue) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back of your Monitor. Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-SUB connection cable. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adaptor. Turn on your computer and monitor. If your monitor displays an image, installation is complete. 2-2. 3. 4. 5. You may get a blank screen depending on the type of video card you are using, if you connect simultaneously both the D-sub and DVI cables to one computer. If you connect properly your monitor using the DVI connector but get a blank or fuzzy screen, check to see if the monitor status is set to analogue. Press Source button to have the monitor double-check the input signal source. User's Manual Setup (SyncMaster 192T) Connecting Your Monitor Setup-For Multimedia model (Option) 1. 2. 3. 4. 5. PC sound connection terminal (Input) Headphone connection terminal (Output) Volume To listen in privacy,connect headphones here. Connect a sound cable from the input source (sound card,computer,CD-ROM drive). User's Manual Setup Attaching a base (Option) Wall Mounting the Monitor As shown in the figure above, you first fold the stand. You attach the VESA mounting brackets on the wall. You hang the monitor aligning its bottom grove with the bracket. Note: Fold the stand and then fix it using the fixing pin attached to the bottom side of the stand. User's Manual Setup Attaching a base (Option) Attaching a base NOTE: This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad. Squeeze the folded monitor stand into the VESA mounting bracket. Then fasten it using the four supplied nuts with the monitor, mounting pad and VESA mounting bracket aligned. 1. ESA Mounting Brkt 2. Mounting interface User's Manual Setup When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ (Worldwide) http://www.samsungusa.com/monitor (USA) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China) Windows ME 1. Insert CD into the CD ...