SyncMaster 153V/173V/152V/172V/193V/192V/153S/173S/153B/173B Main Page Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Setup Connecting the Monitor Installing the Monitor Driver Automatic Manual Installing VESA compliant mounting On-Screen Display Troubleshooting Check List Q&A Self-Test Feature Check Specifications General Specifications PowerSaver Preset Timing Modes Information Service Terms Regulatory Natural Color For Better Display Authority English > Main > Safety Instructions > Notational Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock English > Main > Safety Instructions > Power When not used for extended periods of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. Notational Power Installation Clean Other Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. This may cause an electric shock or fire. Do not connect too many extension cords or plugs to an outlet. This may cause a fire. English > Main > Safety Instructions > Installation Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor. Notational Power Installation Clean Other Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause injury by falling. Set down the monitor carefully. It could be damaged or broken. Do not place the monitor face down. The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. Leave a space for ventilation between the product and the wall. Poor ventilation may cause the interior temperature to rise and lead to a fire. English > Main > Safety Instructions > Clean When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric. Notational Power Installation Do not spray detergent directly on the monitor. Clean Other Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire. Do not set a glass of water, chemicals or any small metal objects on the monitor. This may cause damage, electric shock or a fire. If a foreign substance gets into the monitor, disconnect the plug and then contact a service center. Contact a Service Center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or a fire. English > Main > Safety Instructions > Other Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. Notational Power Installation Clean Other If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or fire. Be careful not to let water drip into the monitor or expose the monitor to moisture. This may cause malfunction, an electric shock or a fire. Especially avoid operating the monitor near water or outdoors where it could be exposed to snow or rain. If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. The monitor may malfunction, causing an electric shock or a fire. Then contact the Service Center. Keep the power off when there is thunder and lightening outside, or let the monitor remain unused for an extended period of time. The monitor may malfunction, causing an electric shock or a fire. Do not try to move the monitor by pulling on the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable. Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Do not use or store inflammable substances near the monitor. This may cause an explosion or fire. Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury. Do not insert metal objects such as utensils, wire or drill bits, or things that catch fire easily, such as pieces of paper or matches, into the vents or the headphone or A/V ports on the monitor. This may cause malfunction, an electric shock or a fire. Always contact the Service Center if foreign substances/objects enter into the monitor. If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time. Be careful when adjusting the stand angle. Applying too much force may cause the monitor topple over or fall, resulting in injury. Your hand or finger(s) may get caught between the monitor and the stand, causing injury. Adjust the resolution and frequency to the levels appropriate for the model. Inappropriate levels of resolution and frequency may damage your eyesight. 15 inch - 1024 x 768 17,19 inch - 1280 x 1024 Be careful that adapter should not be in contact with water and therefore not be wet. This may cause malfunction, an electric shock or a fire. Do not use adaptor by the waterside or outside particularly when it rains or snows. Be careful that adaptor should not be wet while cleaning floor with water. Keep all power adaptors apart. Possible fire hazard. Keep power adaptor away from any other heat source. Possible fire hazard. Remove and discard vinyl bag from power adaptor before use. Possible fire hazard. Always keep power adaptor in well-ventilated area. Keep the volume at a proper level when you use the headphones. Excessively loud volume levels may damage hearing. Keep a proper distance between your eyes and the monitor screen. Sitting too close to the monitor on a continuous basis may damage eyesight. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not use the monitor where it can be exposed to strong vibrations. Exposure to strong vibrations can be a fire hazard and shorten the life of the monitor. When moving the monitor, turn the power switch off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connecting to other devices, are disconnected before moving the monitor. Failure to disconnect a cable may damage it and lead to a fire or an electric shock. SyncMaster 153V/173V/152V/172V/193V/192V Monitor and Stand Power Cord Unpacking Front Rear Signal Cable Quick Setup Guide Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Warranty Card (Not available in all locations) User's Guide and Monitor Driver, Natural Color software SyncMaster 153S/173S Monitor and Pivot Stand Power Cord Unpacking Front Rear DC-Adapter Signal Cable Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Quick Setup Guide Warranty Card (Not available in all locations) User's Guide and Monitor Driver, Natural Color software Pivot S/W CD(Option) SyncMaster 153B/173B Monitor and Stand Power Cord Unpacking Front Rear DC-Adapter Signal Cable Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Audio Cable Quick Setup Guide Warranty Card (Not available in all locations) User's Guide and Monitor Driver, Natural Color software Pivot S/W CD(Option) SyncMaster 153V/173V/152V/172V/193V/192V Unpacking Front Rear 1. Auto button / Exit button 2. Menu button 3. Power button 4. Adjust buttons a. Power indicator Use this button to auto adjustment direct access. / Use this button to Exit the active menu or the OSD. These buttons allow you to highlight and adjust items in the menu. Use this button to turn the monitor on and off. These buttons allow you to highlight and adjust items in the menu. This light glows green during normal operation, and blinks green once as the monitor saves your adjustments. Note: See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. SyncMaster 153S/173S Unpacking Front Rear 1. Auto button / Exit button 2. Menu button 3. Power button 4. Adjust buttons a. Power indicator Use this button to auto adjustment direct access. / Use this button to Exit the active menu or the OSD. These buttons allow you to highlight and adjust items in the menu. Use this button to turn the monitor on and off. These buttons allow you to highlight and adjust items in the menu. This light glows green during normal operation, and blinks green once as the monitor saves your adjustments. Note: See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. SyncMaster 153B/173B Unpacking Front Rear Use this button to auto adjustment direct access. / Use this button to Exit the active menu or the OSD. These buttons allow you to highlight and adjust items in the menu. Use this button to turn the monitor on and off. These buttons allow you to highlight and adjust items in the menu. When OSD is not on the screen, push the - or + button to adjust volume. This light glows green during normal operation, and blinks green once as a. Power indicator the monitor saves your adjustments. b. PC sound connection Connect the audio cable for your monitor to the audio port on the back of your computer. terminal c. Headphone connection terminal Note: See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. 1. Auto button / Exit button 2. Menu button 3. Power button 4. Adjust buttons SyncMaster 153V/173V/152V/172V/193V/192V Unpacking Front Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. Signal port Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. Note: See Connecting the Monitor for further information regarding cable connections. SyncMaster 153S/173S Unpacking Front Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. Signal port 3. Pin Connect the DC Adapter for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. Press the button on the bottom rear of the stand in order to lock down the stand. Note : Always have your monitor faced front side down on a level surface (not resting on the stand) before locking it down. Pressing the button while the monitor stand is resting on a flat surface may cause your monitor to topple or fall and cause personal injury and/or damage to the unit. Note: See Connecting the Monitor for further information regarding cable connections. SyncMaster 153B/173B Unpacking Front Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. Signal port 3. Pin Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. Press the button on the bottom rear of the stand in order to lock down the stand. Note : Always have your monitor faced front side down on a level surface (not resting on the stand) before locking it down. Pressing the button while the monitor s ...