SyncMaster 173T/193T/170N/171N/172N/173N/174T 191N/192N/193N/191T plus/153T/150N/151N/152N Main Page Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Setup Connecting Your Monitor Installing the Monitor Driver Automatic Manual Installing VESA compliant mounting On-Screen Display Troubleshooting Check List Q&A Self-Test Feature Check Specifications General Specifications PowerSaver Preset Display Modes Information Service Terms Regulatory Natural Color For Better Display Authority Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Notational Power Installation Clean Other Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and reoeptacle. An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. Failure to do so may cause an electric shock or fire. Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. Failure to do so may cause an electric shock or fire. Do not connect too many extension cords or plugs to an outlet. This may cause a fire. Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Notational Power Installation Clean Other Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause injury by falling. Set down the monitor carefully. It could be damaged or broken. Do not place the monitor face down. The CDT surface may be damaged. When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric. Notational Power Installation Do not spray detergent directly on the monitor. Clean Other Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire. Do not set a glass of water, chemicals or any small metal objects on the monitor. This may cause damage, electric shock or a fire. If a foreign substance gets into the monitor, disconnect the plug and then contact a service center. Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. Notational Power Installation Clean Other If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or a fire. Do not place any heavy objects on the monitor. This may cause an electric shock or a fire. For each hour of looking at the monitor, you should let your eyes rest for 5 minutes. This will reduce eye fatigue. Do not use or store inflammable substances near the monitor. This may cause an explosion or fire. Do not try to move the monitor by pulling on the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable. Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury. Keep all power adaptors apart. Possible fire hazard. Keep power adaptor away from any other heat source. Possible fire hazard. Remove and discard vinyl bag from power adaptor before use. Possible fire hazard. Always keep power adaptor in well-ventilated area. If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time. SyncMaster 173T/193T/191T plus/153T/174T Monitor andt Stand Power Cord Unpacking Front Rear Signal Cable DVI Cable(Option) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Quick Setup Guide Warranty Card (Not available in all locations) User's Guide and Driver Installation CD Pivot S/W CD(Option) For Multimedia model (Option) Multimedia Speaker Stand Sound Cable SyncMaster 170N/171N/172N/173N/191N/192N/193N/150N/151N/152N Monitor and Stand Power Cord Unpacking Front Rear Signal Cable Quick Setup Guide Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Warranty Card (Not available in all locations) User's Guide and Driver Installation CD Pivot S/W CD(Option) For Multimedia model (Option) Multimedia Speaker Stand Sound Cable SyncMaster 173T/193T/191T plus/153T/174T Unpacking Front Rear Use this button to auto adjustment direct access. Use this button to Exit the active menu or the OSD. When push the 'Source' button, then Selects the Video signal while the OSD is off. (When the Source button is pressed to change the input mode, a message appears in the center of the screen displaying the current mode -- analog or digital input signal.) Note:If you select the Digital mode, you must connect your monitor to the graphic card with a digital port using the DVI cable. 3. MagicBright button MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently three different modes are available: Text, Internet, and Entertain. Each mode has its own preconfigured brightness value. You can easily select one of three settings by simply pressing MagicBright control buttons. These buttons allow you to highlight and adjust items in the menu. 4. Adjust buttons Use this button to open the OSD and activate a highlighted menu item. 5. Menu button Use this button to turn the monitor on and off. 6. Power button This light glows green during normal operation, and blinks green once as the 7. Power indicator monitor saves your adjustments. 1. Auto button 2. Exit button Source button Note: See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. SyncMaster 170N/171N/172N/173N/191N/192N/193N/150N/151N/152N Unpacking Front Rear Use this button to auto adjustment direct access. 1. Auto button Use this button to Exit the active menu or the OSD. 2. Exit button 3. MagicBright button MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently three different modes are available: Text, Internet, and Entertain. Each mode has its own preconfigured brightness value. You can easily select one of three settings by simply pressing MagicBright control buttons. These buttons allow you to highlight and adjust items in the menu. 4. Adjust buttons Use this button to open the OSD and activate a highlighted menu item. 5. Menu button Use this button to turn the monitor on and off. 6. Power button This light glows green during normal operation, and blinks green once as the 7. Power indicator monitor saves your adjustments. Note: See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. SyncMaster 173T/193T/191T plus/153T/174T Unpacking Front Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 2. AudioPower - Out (Option) Connect the DVI Cable to the DVI Port on the back of your Monitor. 3. DVI port Connect the signal cable to the 15-pin, D-sub connector on the back of 4. Signal port your monitor. Press the button on the bottom rear of the stand in order to lock down 5. Pin the stand. Note : Always have your monitor faced front side down on a level surface (not resting on the stand) before locking it down. Pressing the button while the monitor stand is resting on a flat surface may cause your monitor to topple or fall and cause personal injury and/or damage to the unit. a. Power on/off Switch Note: See Connecting Your Monitor for further information regarding cable connections. SyncMaster 170N/171N/172N/173N/191N/192N/193N/150N/151N/152N Unpacking Front Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. AudioPower - Out (Option) 3. Signal port 4. Pin Connect the DC Adapter for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. Press the button on the bottom rear of the stand in order to lock down the stand. Note : Always have your monitor faced front side down on a level surface (not resting on the stand) before locking it down. Pressing the button while the monitor stand is resting on a flat surface may cause your monitor to topple or fall and cause personal injury and/or damage to the unit. a. Power on/off Switch Note: See Connecting Your Monitor for further information regarding cable connections. SyncMaster 173T/193T/191T plus/153T/174T Connecting Your Monitor Installing the Monitor Driver Installing VESA compliant mounting Setup-General 1. 2-1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Using the D-sub (Analogue) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back of your Monitor. Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-SUB connection cable. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adaptor. Turn on your computer and monitor. If your monitor displays an image, installation is complete. 2-2. 3. 4. 5. You may get a blank screen depending on the type of video card you are using, if you connect simultaneously both the D-sub and DVI cables to one computer. If you connect properly your monitor using the DVI connector but get a blank or fuzzy screen, check to see if the monitor status is set to analogue. Press Source button to have the monitor double-check the input signal source. Setup-For Multimedia model (Option) 1. Connect the power cord of the multimedia stand to the multimedia stand power port on the back of the monitor. 2. Connect a sound cable from the input source (sound card,computer,CD-ROM drive). 3. To listen in privacy,connect headphones here. Multimedia Speaker Stand 1. 2. 3. 4. 5. 6. Speaker Power Cord On/Off Volume Bass Control Treble Control Stereo Input Jack Headphone Jack SyncMaster 170N/171N/172N/173N/191N/192N/193N/150N/151N/152N Connecting Your Monitor Installing the Monitor Driver Installing VESA compliant mounting Setup-General 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 3. Connect the monitor to the Macintosh computer using the D-SUB connection cable. 4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adaptor. 5. Turn on your computer and monitor. If your monitor displays an image, installation is complete. Setup-For Multimedia model (Option) 1. Connect the power cord of the multimedia stand to the multimedia stand power port on the back of the monitor. 2. Connect a sound cable from the input source (sound card,computer,CD-ROM drive). 3. To listen in privacy,connect headphones here. Multimedia Speaker Stand 1. 2. 3. 4. 5. 6. Speaker Power Cord On/Off Volume Bass Control Treble Control Stereo Input Jack Headphone Jack Connecting Your Monitor Installing the Monitor Driver Installing VESA compliant mounting When prompted by ...