1.pdf 2006-8-9 18:42:10 USER'S MANUAL AW0503B AW0505B AW0509B AW0603B AW0605B AW0609B AW0803B AW0805B AW0809B AW1003B AW14NCB7 AW1005B AW1009B AW089CB AW109CB AW1203B AW1205B AW1209B AW1403B AW1409B AW1803B AW18NCB7 AW1805B AW1809B AW2402B AW2404B AW2406B AW129CB AW140CB AW189CB AW10NCB7 AW12NCB7 Window-type Room Air Conditioner (Cooling) E S DB98-15114B(5) Register your product at www.samsung.com/global/register Safety Precautions The following safety precautions must be taken when using your air conditioner. WARNING Risk of electric shock. · Can cause injury or death. · Disconnect all remote electric power supplies before servicing, installing or cleaning. · This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Users of this product are cautioned not to attempt repair of this product at their own discretion. Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased. Never spill any kind of liquid into the unit. Should this happen, unplug or main switch off the unit and contact an authorized service center. Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. Keep children away from the unit. Do not place any obstacles in front of the unit. Do not spray liquid of any kind into the indoor unit. Should this happen, switch off the breaker used for your air conditioner and contact your installation specialist. Make sure that the unit is correctly ventilated at all times: Do not place clothing or other materials over it. If the wireless remote control will not be used for a long time, remove the batteries. (If applicable) When using a wireless remote control, the distance should not be more than 7 meters from the air conditioner. (If applicable) The air conditioner must be plugged into its own specific power source, which must be installed in compliance with national wiring,earthing and safety regulations. DURING OPERATION If the power cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. This device must be installed according to the national electrical rules. The appliance must be installation that the plug should be easily accessible after installation. If the fuse on PC board is broken please change it with the type of T 3.15A 250V. The breaker of the air conditioner should be all-pole switch; and the distance between its two contacts should be no less than 3.5mm. Such means for disconnection must be incorporation in the fixed wiring. DISPOSING OF THE UNIT Before throwing out the device, it is necessary to pull back the battery cells and get rid of them safely for recycling reasons. When you need to dispose of the unit, consult your dealer. If pipes are removed incorrectly, refrigerant may blow out and come into contact with your skin,causing injury. Releasing refrigerant into the atmosphere also damages the environments. Please recycle or dispose of the packaging material for this product in an environmentally responsible manner. OTHERS Never store or ship the air conditioner upside down or sideways to avoid damage to the compressor. The appliance is not intended for use by young children or infirm persons without supervision: Young children should be supervised to ensure that they do not play with the appliance. Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency. E-2 Contents PREPARING YOUR AIR CONDITIONER Safety Precautions ......................................................................................... Description of Each Component .................................................................... Remote Control - Buttons .............................................................................. Getting Started ............................................................................................... Inserting the Remote Control Batteries .......................................................... 2 4 5 6 7 OPERATING YOUR AIR CONDITIONER Cooling Your Room ........................................................................................ 8 Airing Your Room ........................................................................................... 9 Removing Excess Humidity ............................................................................ 10 Adjusting the Air Flow Direction Horizontally .................................................. 11 Adjusting the Air Flow Direction Vertically ...................................................... 11 PROGRAMMING YOUR AIR CONDITIONER Setting the On Timer ...................................................................................... Setting the Off Timer ...................................................................................... Setting the Sleep Mode .................................................................................. Selecting Energy Saving mode ...................................................................... 12 13 14 15 RECOMMENDATIONS FOR USE Temperature and Humidity Ranges ................................................................ Cleaning Your Air Conditioner ........................................................................ Solving Common Problems ............................................................................ Technical Specifications ................................................................................. 16 17 18 19 E-3 Description of Each Component The design and shape are subject to change. Air outlet Outer air flow blades (up/down orientation) Air outlet Ventilation lever Inner air flow blades (right/left orientation) - Except AW0503B / AW0505B / AW0603B / AW0605B Air inlet (Inside) - Except AW0503B / AW0505B / AW0603B / AW0605B Air inlet (Outside) Air filter (Inside) Power plug (The type of power plug may differ, depending on the local power supply.) Temperature/Timer settings Mode selection button (Cool,Fan, Dry) Energy Saver button Sleep timer setting button Timer setting button Mode Cool/Dry/Fan Temp. E.Saver Sleep Timer Fan Speed Power Temperature adjustment buttons On/Off button Fan speed adjustment button Remote control E-4 Remote Control - Buttons Timer setting button Sleep timer setting button Temperature adjustment buttons Mode selection buttons Fan speed adjustment buttons Energy Saver button On/Off button E-5 Inserting the Remote Control Batteries You must insert or replace the remote control batteries when : You purchase the air conditioner The remote control does not work correctly Use two AAA, LR03 1.5V batteries. Do not use old batteries or different kinds of batteries together. Batteries may be completely discharged after 12 months, even if they have not actually been used. Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it. Insert the two batteries, taking care to respect the polarities : + on the battery with + on the remote control. - on the battery with - on the remote control. Close the cover by sliding it back until it clicks into place. 1 2 3 E-7 Cooling Your Room You must select the Cool mode if you wish to lower the temperature in your room. You can also set the Fan speed. Remote Control Control Panel 1 Press the (On/Off) button. Result: The air conditioner starts up in the Cool mode. The unit beeps twice. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped It will start up normally after three minutes. 2 If the temperature is not displayed on the control panel: Press the button on the remote control or Press the button on the unit one or more times until the temperature is displayed. / button. Result: The unit beeps each time you press the The air conditioner starts up in the Cool mode. You can change modes at any time. 3 To adjust the temperature, press the or buttons on the remote control or unit one or more times until the desired temperature is displayed. The temperature can be set between 64°F and 86°F. Result: Each time you press the or buttons: ­ The temperature is adjusted by 1°F and displayed on the control panel ­ The unit beeps The air conditioner starts cooling, if the room temperature is higher than the selected temperature. If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. 4 To set the fan speed: Press the , or button on the remote control as desired. or Press the button on the unit one or more times until the desired Fan speed(F1, F2 or F3) is displayed. Fan Speed 5 To control the direction of the air flow, refer to page 11. E-8 Airing Your Room If you want to provide air circulation without cooling, you can use the Fan mode. 1 If necessary, press the Result: (On/Off) button. Remote Control Control Panel The air conditioner starts up in the Cool mode. The unit beeps twice. 2 If the fan speed(F1, F2 or F3) is not displayed on the control panel: Press the button on the remote control or Press the button on the unit one or more times until the fan speed (F1, F2 or F3) is displayed. / button. Result: The unit beeps each time you press the The air conditioner starts up in Fan mode. Mode Cool/Dry/Fan Mode Cool/Dry/Fan You can change modes at any time. When the air conditioner is in the Fan mode, the temperature cannot be set or displayed. 3 To set the fan speed: Press the , or button on the remote control as desired. or Press the button on the unit one or more times until the desired fan speed(F1, F2 or F3) is displayed. Fan Speed 4 To control the direction of the air flow, refer to page 11. E-9 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. Remote Control Control Panel 1 If necessary, press the Result: (On/Off) button. The air conditioner starts up in the Cool mode. The unit beeps. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped It will start up normally after three minutes. 2 If the temperature is not displayed on the control panel: Press the button on the remote control or Press the button on the unit one or more times until the temperature is displayed. / button. Result: The unit beeps each time you press the The air conditioner starts up in the Cool mode. You can change modes at any time. 3 To adjust the temperature, press the or buttons one or more times until the required temperature is displayed. Possible temperatures are between 64°F and 86°F inclusive. Result: Each time you press the or buttons: - The temperature is adjusted by 1°F - The unit beeps The air conditioner starts removing the excess humidity; the quantity of air is adjusted automatically. 4 To control the direction of the air flow, refer to page 11. E-10 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the unit. Adjust the air flow blades to the desired position by sliding them side to side. Adjusting the Air Flow Direction Vertically The outer air flow blades can be adjusted to control the vertical air flow direction. (Except AW0503B / AW0505B /AW0509B/ AW0603B/AW0605B/AW0609B) RECOMMENDATION When... Cooling Adjust the blades to face... Upwards. Adjust the air flow blades to the desired position, by pushing them upwards or downwards. If you orient the air flow blades downwards and the unit operates in Cool mode for long periods of time, dew may: - Form on the surface of the blades - Drip from the blades E-11 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given time. You can select the On timer only when the air conditioner is off. You can select the On timer when the air conditioner operates in the Cool or Dry mode. Remote Control Control Panel 1 Check that the air conditioner has been switched off; if necessary, press the (On/Off) button. 2 Set the operating time by pressing the button on the remote control or Timer button on the unit one or more times until the desired time is displayed. The operating time can be set between 1 and 24 hours. Result: Each time you press the Timer button: ­ The time is adjusted by 1 hour and displayed on the control panel ­ The unit beeps The operating time is displayed and decreases automatically to indicate the remaining time. The air conditioner starts u ...