CD-ROM DRIVE SC-152 Safety Precautions The following diagrams illustrate the precautions to be taken when using your CD-ROM drive. Front View of the CD-ROM Drive * The design of this product can be more or less changed according to its characteristics. Rear View of the CD-ROM Drive User's Guide - ENGLISH 1 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment 2 3 4 56 1 2 123 Digital output terminal 4 5 1 2 Headphone Connector The sound output terminal enables you to plug stereo headphones into the drive. It requires a 3.6 mm stereo mini-jack. You must not use the drive in any manner other than that specified in this guide. FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Re-orient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. BG68-00326A Ver : 03 You can connect a sound card or MPEG card which support Digital output terminal to your drive using this two-pin terminal. CAUTION Do not attempt to repair the CD-ROM drive yourself. Contact your dealer or local SAMSUNG representative for all repairs. If you make any adjustments or perform any operations other than those specified in this guide, you run the risk of exposure to hazardous radiation. Avoid exposing your eyes or skin to direct or scattered radiation. Headphone volume control This headphone volume control adjusts the volume for your headphones. You can only use the headphone jack and volume control when you have installed the required software utilities. For example, the Microsoft Windows Media player can be used. Sound output terminal You can connect a sound card to your drive using this four-pin terminal. This function is not covered in detail in this guide. Refer to the documentation supplied with your sound card. 3 4 5 6 LED Disc compartment The compartment opens and closes automatically when you press the Eject button. WARRANTY Please refer to the Samsung limited warranty statements. Precautions 1. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. 2. Always check each disc for cracks before using it. If there are cracks on the surfaces, especially around the border of the center hole, we recommend that you make a copy of the disc immediately and then stop using it. If you continue using the disc, it will probably develop more cracks and eventually cause irreparable damage. 3. Do not use poor quality discs: q From unknown sources q Without any copyright q Scratched or damaged in any way 3 Master/slave select terminal Usually, this is a pre-set configuration as illustrated below. Emergency eject hole If the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfolded paper clip in the hole and push firmlhy) Verify that the setting is as illustrated. If it is not, simply remove the jumper and place it in the correct position. 4 Eject Button Interface terminal This input/output interface terminal is used to connect the 40-pin flat cable from the IDE interface to the CD-ROM drive. 5 2 Power terminal The power terminal is a four-conductor male plug. 1 3 System Requirements Before you install the CD-ROM drive, we strongly recommend that you make certain that your set-up meets the system requirements listed below. Setting Up the Device Driver It is not necessary to set up additional device driver for Window 95/98/2000/NT because it uses the device driver provided by the Window. Solving Technical Problems Frictional sound detected during the operation of Spin-Up and Stop is made ABS (Auto Balance System), not by malfunction. Technical Specifications SAMSUNG continually strives to improve its products. Both the design specifications and these user instructions are thus subject to change without notice. Item Type of computer Free expansion unit Disk space MS-DOS version Windows version Description IBM 486SX 20MHz (or higher) with an IDE interface(or a 100% IBM-compatible computer) 5.25 inch 100KB minimum 5.0(or higher) Windows 95/98/2000/ME/XP Windows NT 4.0(or higher) x Automatic Setup Problem The CD-ROM drive is not detected by the computer. After installing the CD-ROM drive, the PC gets slower. Meaning / Solution x Check that the power, audio and IDE cables are correctly connected to the computer. x Change the IDE cable and reconnect it to the computer. Preferably, connect a second IDE cable to the CD-ROM drive in master mode; see page 7 for further details. x Check the position of the jumper in the master/slave select terminal. x Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site. x This case may occur when there is a Windows installation problem; reinstall Windows. x Check whether the audio cable is correctly connected to the sound output terminal on the CD-ROM drive and the sound card CD-IN terminal. x Check that the sound card is operational. x Adjust the volume control. x Install the latest version of the device driver. x Check whether the CD is of good quality and clean it, if necessary. x Check that the power cable is correctly connected. x Power off and disconnect the PC. Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens. DISC SECTIONS Disc types supported Disc diameter Data transfer rate Access time (1/3 stroke) Data buffer capacity Laser Slide mechanism Spindle motor Load mechanism Button FRONT PANEL Indicator(LED) Headphone output Volume control Required power REAR PANEL Interface connector Audio output Jumper block Work area OPERATING ENVIRONMENT Storage area Dimensions (W x H x D) GENERAL RELIABILITY Net weight MTBF SC-152N CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1, Form-2, CD-Plus, CD-Extra, Photo-CD(Single, Multi-session), Video CD ready, Enhanced CD, CD-I/Fmv, CD-R/RW 1 Insert the setup diskette in the diskette drive and change the directory to A:, where A: is the diskette drive. To do so, type A: after the C:\ prompt and press [Enter]. 2 Type CDSETUP and press [Enter]. 3 Reboot the computer. x 120mm or 80mm Max. 7800KB/s PIO Mode - 4. DMA MW2, Ultra DMA(option) 75ms(typical) 128KB Semiconductor Laser Gear motor Brushless motor Tray, DC motor(Soft Eject) Mode-1 : 1block / 10 bits, Mode-2 : 1 block/10 bits Eject(Open/Close) Busy Stereo Mini - jack (Ø 3,6 mm) 0.60 ± 20% (Vrms) 33 Dial type +5V DC 1.3A, +12V DC 1.5A ATAPI Line out 0.70 ± 20%(Vrms), 47k Device configuration jumper Temperature : 5~45 °C, Humidity : 8~80% Temperature : -40~60 °C, Humidity : 5~90% 146mm(W) x 44.5mm(H) x 202(D)mm 900g (set only) 125,000 POH(Duty 20%) 12 9 The CD-ROM drive is not recognized by MS-DOS. The CD-ROM drive is not detected by Windows. DRIVE PER FORMANCE Installing the CD-ROM Drive Install the CD-ROM drive in your computer horizontally, making sure that the Open/Close button is on the right. Manual Setup No sound is heard from an audio CD. To install the drive, proceed as follows. 1 Make the C:\SAMSUNG directory. 2 Copy the files from the diskette to the C:\SAMSUNG directory. To do so, type COPY A:*.* C:\SAMSUNG after the C:\ prompt and press [Enter]. A CD is not read or is read too slowly. The disc compartment will not open. ERROR RATE 1 2 3 4 5 Turn OFF your computer. Remember to verify the configuration jumper on the rear of the CD-ROM drive. Remove the cover of your PC(main unit of the computer) Remove the blank cover panel of the 5.25 inch unit in which the CD-ROM drive is to be installed. Connect the CD-ROM drive to the IDE interface and power cables Iocated inside your computer. Connectors are keyed so it is impossible to put them in an incorrect position. Do not force the connectors, if they do not seem to fit. Install the CD-ROM drive into the unit and secure it with mounting screws (recommended standard M3x6x4) x Depending on your PC model, you may need to attach guide rails to the drive, so that the drive is held firmly in place. x If you use screws that are longer than the recommended standard, you may damage the drive. Put the cover back on your PC. 3 Edit the CONFIG.SYS file. Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry. LAST DRIVE = Z ----------------------------------------------------------------------DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V x Adjust the size of the replay screen. When the MPEG software plays a Video CD, the pictures are not regular x After checking the display resolution, adjust it, if and the running speed is too slow. necessary. The Disc is not in message is displayed even though a disc has been inserted. The CD-ROM drive is not detected after it is connected to a sound card. x The computer may not recognize the disc if you start playback too quickly after inserting the disc. Open and close the disc compartment and try again. x Clean the disc and try again. x The interface mode of the sound card is AT-BUS. You must therefore connect the CD-ROM drive to the IDE port on the PC mother board, rather than to the sound card, or install an IDE-compatible sound card. 4 Edit the AUTOEXEC.BAT file. Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry. ----------------------------------------------------------------------C :\SAMSUNG\MSCDEX /D:SSCD000 6 5 Reboot the computer. 5 4 6 7 CD-ROM LAUFWERK SC-152 Sicherheitshinweise Die folgenden Abbildungen veranschaulichen die Vorsichtsmaßnahmen, die bei der Benutzung des CD-ROM-Laufwerks getroffen werden müsen. Vorderseite des CD-ROM-Laufwerks Rückseite des CD-ROM-Laufwerks 1 2 3 4 56 1 2 123 Digitaler Audio-Anschluß 4 5 Bedienungsanleitung Bei Aenderungen oder Modifikationen, die der Anwender ohne Bestaetigung vorgenommen hat, verliert der Anwender das Recht den Produkt zu benutzen. Das Laufwerk darf auf keine andere Weise benutzt werden als in diesem Handbuch beschrieben. 1 2 3 4 Kopfhöreranschluß An diese Buchse können Sie einen Stereo-Kopfhörer mit 3,6 mm-Klinkenstecker anschließen. über diesen 2 poligen Steckverbinder können Sie eine Sound-Karte oder eine MPEG-Karte mit digitalem Audio-Signal an das Laufwerk anschließen. Audio Ausgangsanschluß ACHTUNG Versuchen Sie nicht, das CD-ROM-Laufwerk selbst zu reparieren. Wenden Sie sich bei allen eventuellen Reparaturen an Ihren Händler oder Ihre SAMSUNG-Vertretung vor Ort. Lautstärkeregler Mit diesem Regler wird die Lautstärke des Kopfhörers eingestellt. Der Kopfhörer-anschluß und die Lautstärkeregler sind nur funktionsfähig, wenn die erforderlichen Software-Utilities installiert werden. Sie können zum Beispiel den Microsoft Windows Media Player benutzen. über diesen 4poligen Steckverbinder kann das Laufwerk mit einer Sound-Karte verbunden werden. Diese Funktion wird in der vorliegenden Anleitung nicht aüsfuhrlich beschrieben. Sehen Sie in der Dokumentation für das Audio-Zubehörnach. Wasser und Feuchtigkeit vom Gerät fernhalten, da sonst Gefahr durch elektrische Schläge besteht bzw. Geräteschäden auftreten können. LED Disc-Schublade Die Disc-Schublade öffnet und schließt sich automatisch, wenn eine CD eingelegt oder entnommen wird die Taste Open/Close gedrückt wird. Beim Einlegen der CD in die Schublade ist darauf zu achten, daß die beschriftete Seite der CD immer oben ist. Wenn keine CD eingelegt oder entnommen wird, sollte die Schublade immer geschlossen bleiben. GARANTIE Garantie-Reparaturen müssen von Samsung-Fachhändlern oder Samsung-Vertragswerkstätten ausgeführt werden. 3 Jumper für Geräte-Konfiguration Normalerweise sieht die vorgegebene Konfiguration wie folgt aus : Vorsichtsmaßnahme 1. Vor dem Gebrauch sollte man auf den Diskettenriß achten.Wenn ein Diskettenriß doch vorhanden ist(besonders am Rande des Zentralloches), empfehlen wir dringend, eine Kopie aus der Disketten zu machen. Wenn man trotz des Rißes weiterhin diese Diskette benutzt, wird der Riß noch größer, und zum Schulß wird sie total beschädigt. 2. Bei der Benutzung der Disk ...