SH-S202G(TS-H652G)ENG/RUS 2007.4.15 11:28 PM Page 1 Super- DVD Writer SH-S202G(TS-H652G) Safety Precautions The following are basic precautions to ensure user safety and reduce the risk of property damage. Warning/Caution Warning: Caution: To warn the user that failure to comply with the instructions may result in serious injury or death. To caution the user that failure to comply with the instructions may result in damage to property. Introduction · Design and specifications are subject to change without prior notice. Connecting the Cables to the DVD Writer Connecting the Cables Eject Button User Guide - ENGLISH FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Re-orient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. When you install the drive Place the drive on a level surface. · Failure to do so may cause the device to fall onto a hard surface, resulting in damage or malfunction. Disc compartment Do not drop the drive, and protect it fromsevere shocks. · It can damage the drive or cause it to malfunction. · Never allow food particles or foreign substances to enter the drive casing. · Avoid high-humidity environments. Front Power cable EIDE cable Master/slave select terminal Audio cable Disc compartment While operating · If the power cable is not connected · Avoid low- or high-temperature environments. Do not move the drive while in operation and do not attempt to open the disc tray byforce. Make sure to close all working programs before attempting to open the tray and always use the open/close button. Emergency eject hole If the compartment does not open when you press the Eject button, LED CAUTION Change or modifications not expressly approved by the manufacturer responsible for compliance could void the user 's authority to operate the equipment. IEC 60825-1 :1993 +A1 :1997 +A2 :2001 properly, it may cause a fire or damage the drive. Check the direction of the power connector and the drive incline before connection. · To protect against the risk of fire, do ot spill such liquids as alcohol and benzene on the drive. power off the computer, insert a pin or unfolded paper clip in the hole and push firmlhy) 1 2 3 Power terminal Connecting the power cable · The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal the rear of the DVD Writer. LASER STANDARD WEEE Correct Disposal of This Product (Waste Electrical &Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature,indicates that it should not be disposed with other household wastes at the end of its working life.To prevent possible harm to the environment or human health from uncontrolled waste disposal,please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product,or their local government office,for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract.This product should not be mixed with other commercial wastes for disposal. Sound output terminal +5V DC Ground Ground +12V DC Interface terminal Connecting the EIDE cable · Insert the EIDE cable, which is connected to the hard disk to the interface terminal. (Place the red line of the cable close to the Pin 1.) Do not insert a pin into the emergency opening while in operation. Other · Do not place the drive in direct sunlight. Rear Handle with caution to prevent damage from external shock. Do not use cracked, distorted or damaged discs. Do not disassemble, attempt to repair or modify the device without express approval as directed in the manual. Installing a jumper on the master/slave select terminal · Connect a jumper to the rear side of the DVD Writer. If the jumper is connected to MA (Master), it will work in the Master mode. If the jumper is connected to SL (Slave), it will work in the Slave mode. If the jumper is connected to CS (CSEL), you can control the device by using the host interface signal CSEL. (In general, connection to MA is recommended.) CS : Cable Select(CSEL) SL : Slave MA: Master · To reduce the risk of damage, electric shock, and fire. · Samsung Eco-mark The Samsung's own Eco mark helps consumers to easily understand that Samsung develops eco-friendly products. This mark represents Samsung's continuous effort to develop eco-friendly products. In particular, a disc with a crack on the inner tracks may break while in use. Digital output Master/slave select terminal terminal Accessories User Guide, Screw 4ea · RoHS (Restriction of the use of certain hazardous substances in electrical and electronic equipment) The RoHS, the environment regulation announced by European Union, restricts the use of lead, mercury, cadmium, hexavalent chromium, PBB, and PBDE in products put on the market in The European Union after July 1, 2006. BG68-01416A REV.00 · Any change or modification not expressly approved by designated qualified personnel could void your authority to operate this device. Important to read and understand Do not disassemble at all times 1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended that you make a copy immediately and use the copy instead. When a cracked disc is used continuously,the size of the crack is likely to grow and it will eventually result in irreparable damage to the disc. 2. Do not use low quality discs (i.e., illegal products, scratched or damaged discs). Design and specifications are subject to change without prior notice. * To write with the highest speed(20X), you must use 80 pin E-IDE cable. 4 Connecting the EIDE cable from a sound card · Connect the 4-pin audio cable between the sound output terminal on the DVD Writer and the audio input terminal on the sound card. - http://www.samsung-ODD.com - http://www.samsung.com 1 2 3 4 Installing the Drive When using one EIDE cable · Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear of the DVD Writer. Slave Drive (Choose the SL Jumper) Using the Drive/Storing and Cleaning Your Discs Using the DVD Writer Solving Technical Problems · The friction noise generated during SPIN-UP and STOP is caused by the Technical Specifications Category SH-S202G(TS-H652G) DVD Writer DVD : DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-ROM, DVD-Video, DVD+R (Dual), DVD-R (Dual), DVD-RAM, DVD Multi-Border CD : CD-ROM, CD-R, CD-RW, CD-DA, CD+E(G) CD-MIDI, CD-TEXT, CD-ROM XA, Mixed Mode CD CD-I, CD-I Bridge (Photo-CD, Video-CD), Multisession CD (Photo-CD, CD-EXTRA, Portforio), System Requirements Intel Pentium 800MHz(or higher), 256 MB of RAM (or higher)with an EIDE interface,Windows 2000/ XP/ Vista Automatic Ball Balancing System(ABS) and is not a malfunction. The DVD Writer is not detected by the computer. Installing the DVD Writer How to install the DVD Writer on your PC. First, remove the cover; connect the cable to the DVD Writer and then to the PC. Hard Drive MainBoard 1 2 3 4 Push the power button and boot the computer. After booting the computer, open the disc compartment by pressing the Eject button. Insert the disc (CD) with the label on the disc facing upwards and close the disc compartment by pressing the Eject button. The indicator light comes on. Play the disc (CD). · Check that the power, audio and EIDE cables are correctly connected to the computer. · Change the EIDE cable and reconnect it to the computer. Preferably, connect a second EIDE cable to the DVD Writer in master mode. · Check the position of the jumper in the master/slave select terminal. After installing the DVD Writer, the PC gets slower. DISC Usable Discs 1 The DVD Writer is not recognized by MS-DOS. When using two EIDE cable · Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear of the DVD Writer. If necessary, attach a horizontal bracket to both sides of the drive. · You can purchase these accessories separately from your computer dealer. (Screws for use: M3 X 6 X 4) · Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site. - http:// www.samsung-ODD.com - http:// www.samsung.com Disc Diameter Interface Support Access time (Random) 4.72 Inch or 3.15 Inch (120mm or 80mm) ATA/ATAPI (E-IDE) PIO Mode 4: 16.6MB/sec Ultra DMA Mode 4: 66MB/sec 110ms (Random) 130ms (Random) Write CAV 20X (27.0MB/sec) ZCLV 8X (10.8MB/sec) ZCLV 12X(16.2MB/sec) ZCLV 12X(16.2MB/sec) CAV 20X (27.0MB/sec) CLV 6X (8.1MB/sec) PCAV 12X (16.2MB/sec) PCAV 48X (7.2MB/sec) ZCLV32X (4.8MB/sec) CLV 10X (1.5MB/sec) CLV 4X (0.6MB/sec) Read CAV 16X (21.6MB/sec) CAV 12X (16.2MB/sec) CAV 12X (16.2MB/sec) CAV 12X (16.2MB/sec) CAV 16X (21.6MB/sec) CAV 12X (16.2MB/sec) PCAV 12X (16.2MB/sec) CAV 16X (21.6MB/sec) CAV 12X (16.2MB/sec) CAV 48X (7.2MB/sec) CAV 40X (6.0MB/sec) CAV 40X (6.0MB/sec) CAV 40X (6.0MB/sec) CAV 40X (6.0MB/sec) Interface Port PIO mode DMA mode CD-ROM DVD-ROM Media Type DVD+R DVD+RW DVD+R DUAL DVD-R DUAL DVD-R DVD-RW DVD-RAM DVD-ROM(Single) DVD-ROM(Dual) CD-ROM CD-R US-RW HS-RW CD-RW The DVD Writer is not detected by Windows. A CD is not read or is read too slowly. The disc compartment will not open. · This case may occur when there is a Windows installation problem; reinstall Windows. Playing CD-DA/Audio CDs · Run the CD player program supplied with the sound card or play the Windows Media Player. - If there is only one Optical drive: select MA (Master). Master Drive (Choose the MA Jumper) SEC 1 PRI 1 · Check whether the CD is of good quality and clean it, if necessary. Playing Video CDs · Follow the instructions provided with the disc. · · 2 · A video card or MPEG software and a sound card need to be installed to view video CDs. Remove the plate from a free expansion slot and install the DVD Writer, as shown in the illustration. · If you have no free expansion slot, install the drive in place of the diskette drive. · Make sure to use the standardized screws supplied (M3X6). - To use screws other than M3X6 may result in malfunction. · If the drive is vertically installed, you cannot use an 8 cm Mini Disc because the disc is movable. Check that the power cable is correctly connected. Power off and disconnect the PC. Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens. When the MPEG software plays a Video CD, the pictures are not regular and the running speed is too slow. The Disc is not in message is displayed even though a disc has been inserted. Hard Drive MainBoard Storing Your Discs · Do not place a disc in direct sunlight. · Store a disc vertically in a well-ventilated and stable location. · Do not write or attach a label on a disc. · Do not drop a disc or place heavy objects on it. · Adjust the size of the replay screen. · After checking the display resolution, adjust it, if necessary. Data transfer rate(MAX) -If there is two Optical drive, select MA (Master) / SL (Slave). Master Drive (Choose the MA Jumper) Slave Drive (Choose the SL Jumper) SEC 1 PRI 1 · The computer may not recognize the disc if you start playback too quickly after inserting the disc. Open and close the disc compartment and try again. Clean the disc and try again. · (Choose the MA Jumper) (Choose the SL Jumper) Hard Drive MainBoard Plate Cleaning Your Discs DVD Writer Horizontal Bracket The DVD Writer is not detected after it is connected · The interface mode of the sound card is AT-BUS. You must therefore connect the DVD Writer to the EIDE port on the PC mother board, rather than to the sound card, or install an EIDE compatible sound card. · Do not touch the s ...