GB DIGITAL VIDEO RECORDER SHR-1010 User's Manual Class A (Industrial) - This device is for industrial use and qualified for electromagnetic waves restriction - For the safety use of this device, please read and heed all "Safety Warnings and Cautions" DIGITAL VIDEO RECORDER GB GB CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plus. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a used, caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product. To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and 2) This device must accept any interference that may cause undesired operation. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. ii iii GB Contents iii GB Important Safety Instructions Contents I. Summary 1. Introduction 2. Characteristics 3. Name and Function of Each Part 4. Unpacking 5. Attaching/Deta ching HDD 4 4-1 4-3 4-4 IV. Record 1. Basic Record 2. Recording Alarm 3. Reservation Record iv ~ v 1 1-1 1-2 1-3 1-7 1-9 5 5-1 5-3 5-4 5-5 V. Retrieval and Playback 1. Retrieval Menu View 2. Date and Time Search 3. Alarm Record Retrieval 4. Basic Playback 2 2-1 2-2 2-3 2-4 II. Connection with Other Devices 1. Connection to External Devices 2. Connection with Multiplexer 3. System Connection for Alarm Recording 4. Connection with PC for Use 6 6-1 6-2 7 7-1 7-3 VI. Others 1. Product Standards 2. Appearance Drawing Appendices Chech Points before Call Service Center Q&A 3 3-1 3-3 3-6 3-11 3-12 3-15 3-16 3-17 3-19 3-23 3-24 iv III. Basic Method to Use 1. Booting the System 2. The Basic Screen View 3. Menu View 4. Setting of Date, Time and Screen 5. Record Setup 6. Alarm Record Setup 7. Reservation Record Setup 8. System Setup 9. Image Copy&Play Setup 10. Communication Setup 11. System Information v GB I. Summary 1 DIGITAL VIDEO RECORDER GB 1I ntroduction The DIGITAL VIDEO RECORDER SHR-1010 is a Digital Time Lapse Recorder that uses HDD as recording media. How to use it is simple and therefore existing users of Time Lapse VCR can also access to it. You can also perform continuous recording on the HDD and directly view image recorded without turning videotapes as in the existing Time Lapse VCR. The SHR1010 can record video and audio at the same time. 2Char s s s s s s s s GB acteristics Upon booting the system, it recognizes automatically whether the incoming signal is NTSC or PAL signal. Adjusting screen quality in 4-steps q Very High, High, Standrad, Low NTSC: MAX 30 ~ 0.5FPS PAL: MAX 25 ~ 0.5FPS Variously changing numbers of recording fields per second. q q Reservation recording by using timers Recording by alarm Multiplexer link Convenient retrieval function q Date & Time Search, Alarm Event Search, SYSTEM LOG Automatic booting of system in power failure recovery during recording mode, and starting of recording 1-1 1-2 DIGITAL VIDEO RECORDER GB 3Name No 1 GB and Function of Each Part Front View ! @# $% ^ & * ( ) 1 23 Name Hard Rack Function To install and uninstall of hard disk is available and you could change the hard disk easily. LED is an indicator of Hard disk status. It verifies power supply connection and normal hard disk access status. You can lock the Hard disk of Hard Rack. You can back up the data stored in the system to MEMORY STICK easily. 10 2 HDD LED Hard Rack STICK MEMORY STICK STATUS DISPLAY LED No 9 Name UP Function Moves up the cursor in a menu or increases the detailed setting value for the menu. Shows still cuts in the forward direction. Rewinds recorded images during play. Edits or modifies the left value of a menu for setting up the menu. Moves down the cursor in a menu or decreases the detailed setting value for the menu. Shows still cuts one by one in the backward direction. Forwards recorded images fast during play or modifies the right value of a menu for setting up the menu. To use 'STOP/ENTER' to stop Playing or Recording, it can be used as ENTER when setting MENU. 3 4 5 MEMORY STICK LEFT POWER ALARAM MEMORY STICK Displays system status. q POWER : Checks power On. q ALARM : Checks Alarm turns operates. q MEMORY STICK : It verifies data copies to MEMORY STICK. Records current live images. Plays recorded data. Pauses screen or shows still screen during play. Displays the system setup menu or turns menu by stages. 11 DOWN 6 7 REC PB/STILL MENU 12 RIGHT STOP/ENTER 8 13 1-3 1-4 DIGITAL VIDEO RECORDER GB GB Rear View ! @ #$ % ^ & *( No Name External In/Out Port q Function The system gives an alarm when the High(5V) signal incomes for more than 0.5 seconds in the N.C.(Normally Closed) mode and when the Low(0V) signal incomes for more than 0.5 sec onds in the N.O.(Normally Open) mode. GND ALARM OUT: The High(5V) signal comes out during alarm recording. ALARM RESET IN : The system cancels the alarm when the Low(0V) signal incomes for more than 0.5 seconds. 1 SHOOT REC IN REC START IN: The system starts recording when the Low(0V) signal incomes for more than 0.5 seconds. REC END: The Low(0V) signal comes out for about 1 second when you set the DISK END MODE in the RECORD MODE SETUP menu to SETUP and the HDD consumes all of its free space. TRIGGER OUT: This signal converts the Multiplexer record ing output screen. Caution If suffocated, the air inlet or outlet may harm the product performance. Please install the product where you can secure free ventilation. Never allow goods around the air inlet or outlet if they are big enough to suffocate it. If you want to run DVRs on cabinets or Reck, be sure to secure air ventilation. 7 q q q No 1 Name Image Input Port THROUGH Terminal Image Output Port S-VHS PORT Voice In/Out Port RS-232 Port Function It is the composite image signal input port(BNC Style Connector). You can use THROUGH Terminal to send VCR signal to another VCR. q q q 2 3 4 5 6 q It is a composite image signal input port (BNC Style Connector). It is the S-VHS image signal in/out port. It is a voice signal in/out port(RCA Jack). 9 8 FACTORY RESET POWER Initializes the system. Supports the DC power socket. You can plug in the 100-250 VAC power cord. It is a serial port for remote control. 1-5 1-6 DIGITAL VIDEO RECORDER GB 4Unpac GB king Caution Be sure to use the adapter for SHR-1010 only. Be sure to pay attention to the following when you use the adapter. 1. Use it only in the room. 2. Prevent water or liquid from entering the connector or product. 3. Avoid excessive impact or force. 4. Don't pull the output plug unreasonably. 5. Don't disassemble the product on your own. 6. Abide by the rated input and output range. 7. Use KS power cords only. 8. For the product with an input ground, be sure to use the power cord with a ground. When purchasing product, first remove packing and put it on a flat floor or at a place to use it. Then, ensure all following contents are included: Main body User's Manual 1 power cord 1 Adapter 2 Hard Rack Locking Keys 010 R-1 SH Caution The above contents can be changed without notice in order to improve the performance or function of the product. 1-7 1-8 DIGITAL VIDEO RECORDER GB 5At GB taching/Deta ching HDD H.D.D. Mounting HDD POWER ALARAM REC PB H.D.D. Lift up 5. Erect the front handle of the internal 6. Lock the hardrack with the key and turn the power on. MEMORY STICK POWER rack to push it toward the external rack. REC ALARAM MEMORY STICK Lift up 2. Take the hard rack out of the inter nal rack. Erect the front handle and pull it down. After the handle reaches to the end, pull it down to the bottom for firm fixing. 1. At first, open the Hard Rack cover in front of Main Deck and then open Hard Rack using Hard Rack key. Caution To operate system, you have to lock the key of Hard Rack. When changing HDD or uninstalling Hard Rack, please make sure that power indicating LED of HDD is turned off. Otherwise, the HDD may fall in trouble. Be sure to format all HDDs before use if they have been used in the other PC. Otherwise, the system may not operate properly. We recommended SEC Spinpoint V40 SV4002H or SV8004H for this product. Please be sure to call the store where you bought the HDD before you want another one. H.D.D. H.D.D. 3. Connect the internal rack data cable and power cord with the HDD. 4. Put the HDD in the internal rack and fix it with a screw. 1-9 1-10 GB II. Connection with Other Devices 2 DIGITAL VIDEO RECORDER GB 1Connec tion to External Devices 2 LIGHT Connection with Multiplexer (e.g. connection to SDM-160) CAMERA 1 2 3 . . . 16 MONITOR OUT GB CAMERA TRIGGER OUT ALARM IN GND SHR-1010 VIDEO RECORDER VIDEO IN VIDEO OUT VIDEO OUT (NTSC/PAL MONITOR) SDM-160 DIGITAL MULTIPLEXER AUDIO OUT s SIREN s s MICROPHONE s PC s SDM-160 is a Multiplexer for NTSC, and SDM-160P is a Multiplexer for PAL. For details on the functions of SDM-160, please refer to the user's guide of SDM-160. Connect this unit's video signal input jack to the video signal output jack of SDM-160 and connect this unit's video signal output jack to the video signal input jack of SDM-160. Connect the alarm output jack (ALARM OUT) of SDM-160 to this unit's alarm input jack (ALARM IN), and connect the VTI jack of SDM-160 to this unit's trigger output jack (TRIGGER OUT). Connect both GND terminals together. Caution s This device can be applied to external devices such as image signal input camera, voice signal input microphone, NTSC for the output of both signals, or PAL monitor. It can be also applied to external devices at user request. It can be applied to PC for serial communication. s s - Be sure to connect the trigger output terminal (TRIGGER OUT) of this unit to the Multiplexer. Otherwise, a normal recording cannot be made. (For the connection method, please refer to the user's guide for the Multiplexer you want to use.) - If the systemís recording field rate is set to 0.50 ~ 15 FPS (Fields Per Second) for the input NTSC video signal and to 0.50 ~ 12.5 FPS for the input PAL video signal, be sure to set the Multiplexer in such a way that the recording output screen is switched by the Trigger Pulse. (For settings related to the recording field rate, please refer to "(2) PICTURE RATE"on p. 3-12.) - If the system's recording filed rate is set to 30 FPS for the input NTSC video signal and to 25 FPS for the input PAL video signal, a half of the input video channels may not be recorded depending on the type of Multiplexer. In this case, set the recording field rate to 60 FPS for NTSC and to 50 FPS for PAL. Caution A CRT monitor capable of displaying an NTSC or PAL video signal must be use ...