Assembly Instructions for Model: VMUC1 Thank you for choosing a Sanus Systems Vision Mount under cabinet mount. The VMUC1 is designed to hold up to a 17 inch flat panel LCD weighing up to 18 lbs. Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly to you. Never use defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified by Sanus Systems. Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of purchase. Required Tools: Phillips screw driver, drill, 1/4 inch drill bit Supplied Parts and Hardware: Some parts not shown as actual size* (3) T - Nuts - b (1) Mount Assembly - a (3) 10-24 x 5/8 Bolt - c (4) M4 x 10 mm Bolt - d (4) M4 x 20 mm Bolt - e (4) .5 inch Spacer - f (4) Cable Tie - g (1) Allen Key - h Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 1.3.05 Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com Step 1: Remove Cover Using a Phillips screw driver loosen the two flat head bolts from the cover and slide it down and away from the mounting plate. See Diagram 1 for assistance. You will re-install the cover once cable management is complete. Diagram 1 a mounting plate cover flat head bolts Step 2: Prepare Mounting Surface Use the base of the Mount Assembly (a) as a template to mark three holes in the cabinet in the desired location. Drill three 1/4 inch holes at the marked locations. See the dimensional drawing on the right for assistance. See page 9 for a 1:1 scaled version of the dimensional drawing. Dimensional Drawing 3.28 1.89 1.89 Step 3: Secure Mount Assembly to cabinet Using the 10-24 x 5/8 Bolts (c) and the T - Nuts (b) secure the Mount Assembly to the cabinet. See Diagram 3 for assistance. Note: Make sure the spikes on the T - Nuts is facing toward the cabinet. Diagram 3 Detailed View b cabinet c spike Step 4: Attach flat panel display to mounting plate Make sure no power is supplied to the display before mounting the display! Warning: Watch for pinch points. Do not put your fingers or cables between movable parts. Once the Mount Assembly (a) is secured to the cabinet, align the appropriate slots in the mounting plate with the four mounting holes of your LCD display. Use either four M4 x 10 mm Bolts (d) or four M4 x 20 mm Bolts (e) with four .5 inch Spacers (f). Diagram 4a below shows the M4 x 10 mm Bolts being used. Diagram 4b on the next page shows the M4 x 20 mm Bolts with the .5 inch Spacers. Detailed View Diagram 4a LCD panel d mounting plate Step 4 (cont) The .5 inch Spacers (f) should only be used if there is an obstruction or the hole pattern is physically recessed on the back of the LCD panel. See Diagram 4b for assistance. Detailed View Diagram 4b e mounting plate f LCD Panel Step 5: Adjusting the screen height. Using a Phillips screw driver, slightly loosen the Bolts (d,e) that secure the LCD panel to the mounting plate. Adjust the LCD panel to the desired height. Tighten the Bolts (d,e) to secure the LCD panel to the mounting plate. See Diagram 5 for assistance. Diagram 5 d,e mounting plate Step 6: Adjust tension of Mount Assembly The tension of the Mount Assembly (a) can be adjusted by simply tightening or loosening the tension bolt labeled in Diagram 6 with the provided Allen Key (h). Diagram 6 Detailed View tension bolt Step 7: Remove Cable Cover Using a Phillips screw driver, loosen the screw in the center of the cable cover and remove cover. See Diagram 7 for assistance. Note: You will re-install the cable cover once cable management is completed. Diagram 7 Detailed View cable cover screw Step 8: Cable Management (±35° swivel) If ±110° swivel is desired, skip to Step 9. If ±35° swivel is desired, Step 8 will be the final step. Swivel the Mount Assembly (a) 35° either left or right. You will run the cables in the opposite direction. You can attach the Cable Ties (g) in locations marked in Diagram 8 below. Re-install the cable cover and the base cover in the same manner they were removed. Diagram 8 a cable path cable tie holder Step 9: Remove Degree Stop Using provided Allen Wrench (h), remove the 35 degree stop. See Diagram 9 for assistance. Diagram 9 35 degree stop Step 10: Cable management (±110°) Swivel the Mount Assembly (a) 110° either left or right. You will run the cables in the opposite direction. Cables must be wrapped a complete 360° inside the base of the Mount Assembly. You can attach the Cable Ties (g) in locations marked in Diagram 8 below. Reinstall the cable cover and the base cover in the same manner they were removed. Diagram 10 cable tie holder a cable path Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 1.3.05 Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com Dimensional Drawing - Scaled 1:1 Front 3.28 1.89 1.89 Back ...