User manual SANUS COMPONENT FURNITURE VIDEO LOWBOY - CFV69CB

Assembly instructions for Model: CFV69 Thank you for choosing Sanus Systems Component Furniture. Please check carefully to make sure there are no missing or defective parts. Never use defective parts. Improper assembly may cause damage or serious injury. If you have any questions regarding this product, contact Sanus at 800.359.5520 or visit www.sanus.com. Our customer service representatives can quickly assist you with missing or damaged parts. Replacement parts for Sanus products purchased through authorized dealers can be shipped directly to you. Please call Sanus Systems before returning products to the point of purchase. Required Tools: Phillips screw driver NOTE: Check to make sure all of the parts and hardware are accounted for. Hardware: Shown at actual size. Cam Pin - B Qty. 8 Carpet Spike & Nut - A Qty. 4 Back Panel Spacer - C Qty. 12 Back Panel Bolt - D Qty. 12 Mounting Block Screw - E Qty. 8 Glass Shelf Pin - F Qty. 4 Shelf Pin - G Qty. 8 Dowel - H Qty. 6 Threaded Cam Pin - I Qty. 4 Barrel Nut - J Qty. 4 Barrel Nut Bolt - K Qty. 4 Isolation Pad - L Qty. 8 Bottom Shelf Pin - M Qty. 4 Wood Screw - N Qty. 4 Knob Bolt - O Qty. 2 Knob - P Qty. 2 Hinge Screw - Q Qty. 8 Hinge Plate Screw - R Qty. 8 Allen Key - S Qty. 1 Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02.16.06 (000022) Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com Parts: Foot - T Qty. 4 Cntr. Panel Mtg. Block - U Qty. 4 Bottom Shelf Retainer - V Qty. 2 Hinge - W Qty. 4 Hinge Plate - X Qty. 4 Top - Y Qty. 1 Bottom Shelf - Z Qty. 1 Front Rail - AA Qty. 2 Back Rail - BB Qty. 2 Outer Back Panel - CC Qty. 2 Center Back Panel - DD Qty. 1 Isolation Shelf - EE Qty. 2 Glass Shelf - FF Qty. 2 Side Panel - GG Qty. 2 Left Center Divider - HH Qty. 1 Right Center Divider - II Qty. 1 Center Panel - JJ Qty. 1 Side Door - KK Qty. 2 Step 1: Add feet WARNING: The ends of the Carpet Spikes are very sharp and may scratch floors or furniture. All sharp objects can be hazardous to children. For this reason Sanus Systems provides the carpet spikes as an option. Sanus Systems will not be liable for damage or injury. Add a Foot (T) to the Pillar of each Side Panel (GG) as shown in Diagram 1. If you wish to install the Carpet Spikes (A), thread each Carpet Spike into the Foot as seen in Diagram 1. To adjust the height of the Carpet Spike, simply thread it in or out; then, snug the Nut against the base of the Foot to lock the Carpet spike in place. Diagram 1 Pillar GG T A Nut Spike Step 2: Attach the lower Front and Back Rails to the first Side Panel NOTE: Make sure the flange on the Front Rail (AA) faces the back of the unit. AA Flange Attach the Front Rail (AA) to the Side Panel (GG) by sliding the Clamp down the groove in the Side Panel Pillar as shown in Top View A. Once the Front Rail is positioned at the bottom of the groove and resting on the Foot (T), tighten the Allen Bolt on the back side of the Front Rail so the clamp widens to hold the Front Rail firmly in place. NOTE: Make sure the arrow on each Cam is facing the hole in the outside of the Back Rail (BB). Insert two Cam Pins (B) into each end of the Back Rail (BB) as shown in the Detail View of Diagram 2. Insert the Cam Pins until there is a small space between the head of the Cam Pin and the Back Rail. Attach the Back Rail (BB) by sliding the Cam Pins (B) down the groove on the Side Panel (GG) Pillar as shown in Top View B. Once the Back Rail is resting on the Foot, tighten the Cams labeled in the Detail View of Diagram 2 to hold them in place. Make sure the Back Rail is oriented so the threaded holes near the ends are on the top, and the Cams face inside the cabinet, as shown in Diagram 2. Top View A (Front Left Corner) Diagram 2 AA Allen Bolt Detail View B AA Cam Clamp T GG BB GG Cam Pin (B) BB Top View B (Back Left Corner) GG BB Step 3: Add second Side Panel Assembly Attach the second Side Panel Assembly (GG) by sliding the clamp in the Front Rail (AA) and the Cam Pins (B) in the Back Rail (BB) down the grooves in the Pillars on the Side Panel until they are at the bottom of the Pillar and resting on the Foot (T). Use the Allen Key (S) to tighten the Allen Bolt in the back of the Front Rail to widen the clamp and secure it to the Pillar. Tighten the two Cams in the Back Rail (BB) to secure it to the Pillar. Top View (Front Right Corner) Top View (Back Right Corner) Diagram 3 Allen Bolt GG Allen Bolt GG BB BB Cam Pin (B) GG AA Clamp T AA T Step 4: Add Bottom Shelf Thread a Bottom Shelf Pin (M) into the Side Panel (GG) as shown in Diagram 4. Repeat this process until all four Bottom Shelf Pins have been inserted into both Side Panels. Press fit the Bottom Shelf (Z) until it is locked into the Bottom Shelf Pins (M). Diagram 4 GG Z Z GG GG M Step 5: Add Center Dividers Insert a Barrel Nut (J) into the top and bottom of the Left and Right Center Dividers (HH,II) as in Detail A, Diagram 5. NOTE: Make sure the threaded hole in the Barrel Nut (J) lines up with the hole in the back of the Center Dividers (HH,II), and the arrow on the Cam is pointing toward the hole in the bottom as in Detail B, Diagram 5. Insert four Threaded Cam Pins (I) into the Bottom Shelf (Z) as in Detail C, Diagram 5. Tighten each Threaded Cam Pin (I). Attach the Center Dividers (HH,II) to the Bottom Shelf (Z); then, tighten each Cam with a phillips screw driver, turning the Cam clockwise. Diagram 5 HH II Z HH or II Cam I J Z Detail A Detail B Detail C Step 6: Add Top Rails AA NOTE: Make sure the Flange on the Front Rail (AA) faces the back of the unit. Flange Attach the Front Rail (AA) to the Side Panel Assemblies (GG) by sliding the clamp down the groove in each Side Panel Pillar as done in Step 2. When Front Rail (AA) is level with the tops of the Center Dividers (HH,II), tighten the Allen Bolt on the back side of the Front Rail to expand the clamp, thus holding the Front Rail firmly in place. NOTE: Make sure the arrow on each Cam is facing the hole in the outside of the Back Rail (BB). Insert two Cam Pins (B) into each end of the Back Rail (BB) until there is a small space between the head of the Cam Pin and the Back Rail as shown in Diagram 6. Attach the Back Rail (BB) by sliding the Cam Pin (B) down the groove on the Side Panel Pillar. Once the top of the Back Rail is level with the top of the Center Dividers (HH,II), tighten each Cam with a phillips screw driver, turning the Cam clockwise. Diagram 6 BB Cam BB GG AA B GG HH II Step 7: Add Barrel Nut Bolts NOTE: You may need to loosen Cams tightened in Step 6 to Line up the holes. If you do, make sure to tighten them when finished with this Step. Thread the Barrel Nut Bolts (K) through the Back Rail (BB) and into the Center Divider Panels (HH,II); then,tighten the Barrel Nut Bolts (K) until the Back Rail (BB) is secured to the Center Divider Panels (HH,II). Diagram 7 HH II BB BB K Step 8: Add Bottom Shelf Retainer Gently rotate the cabinet so it is resting on its back; then, using the Wood Screws (N) secure the Bottom Shelf Retainers (V) to the Bottom Shelf (Z). Diagram 8 N V Z N V Step 9: Add the Back Panels Insert a Back Panel Bolt (D) through the Outer Back Panels (CC), Center Back Panel (DD), and a Spacer (C); then, thread it into the Back Rail (BB). Repeat the process until all 12 Back Panel Bolts are attached to the Back Rails. Tighten the Back Panel Bolts. Diagram 9 BB C D BB CC CC DD CC Step 10: Add Top Insert a Dowel (H) into each hole in the bottom of the Top (Y). Align the Dowels (H) in the bottom of the Top (Y) with the holes in the Center Dividers (HH,II) and the pillars on the Side Panels (GG); then, press fit the Top onto the Side Panels, and Center Dividers. Diagram 10 Y H H GG GG HH II Step 11: Add Isolation Pads to Isolation Shelf NOTE: Make sure the soft side of the Isolation Pad is facing toward the shelf when inserting it into the Isolation Shelf. Pull the adhesive backing from the soft side of the Isolation Pads (L) and press them into the holes in the Isolation Shelf (EE). Diagram 11 EE L Step 12: Add Isolation Shelves Insert two Shelf Pins (G) per Side Panel Assembly (GG) and two Shelf Pins per Center Divider (HH, II) at the desired height. Align the holes on the bottom side of the Isolation Shelves (EE) with the Shelf Pins (G), and place the Isolation Shelf on the Shelf Pins. Repeat the process for the second Isolation Shelf. You can level the Isolation Shelves by adjusting the Screw in the Shelf Pin with an Allen Key; then, locking it with the Nut. Diagram 12 GG EE Screw G GG G Nut EE HH II EE GG Step 13: Add Glass Shelf Insert four Glass Shelf Pins (F) at the desired height into the Center Dividers (HH,II). Place the Glass Shelf (FF) on the Glass Shelf Pins. Diagram 13 FF HH F FF II F Step 14: Add Center Panel Mounting Blocks Attach the Center Panel Mounting Blocks (U) to the Center Dividers (HH,II) by threading the Mounting Block Screws (E) through the Mounting Blocks and into the Center Dividers. Tighten each Mounting Block Screw with a phillips screw driver. Repeat until all four Mounting Blocks are in place. Diagram 14 U U E HH U II Step 15: Attach Center Panel Press the Center Panel (JJ) onto the Mounting Blocks (U). Diagram 15 U U JJ Step 16: Prepare the Doors Insert a Knob Bolt (O) through the backside of the Side Door (KK) and thread it into the Knob (P). Tighten the Knob until it is flush with the front side of the Side Door. Perform this procedure for both Side Doors. Diagram 16 O KK P Step 17: Attach Hinge to Side Door Attach the Hinges (W) to the Side Doors (KK) by threading a Hinge Screw (Q) through each hole in the Hinge and into the Side Door. Tighten each Hinge screw until the Hinge is secure to the Side Door. Perform this procedure for both Doors. Diagram 17 Q W KK Step 18: Add Side Doors Attach the Hinge Plates (X) by threading a Hinge Plate Screw (R) through each hole in the Hinge Plate and into the Side Panel (GG). Repeat this process until all four Hinge Plates are attached; then, tighten the Hinge Plate Screws with a phillips screw driver. NOTE: To attach each Hinge (W) to its Hinge Plate (X), the bolt along the back center of the Hinge Plate must be loose during installation. This bolt must be loose. The slot on the end of the Hinge (W) will fit around the bolt on the Hinge Plate (X). The top and bottom Hinges should engage at the same time. Once the two parts of the Hinge are mated, tighten the bolt on the Hinge Plate. Perform this procedure for both Doors. Diagram 18 GG X R W Step 19: Hinge Adjustment Each hinge Assembly is adjustable in multiple directions. Diagram 19 Side Adjustment Depth Adjustment Height Adjustment m m .5 m + 0.5 m -3 +0 - 2 .5 m .5 m m m +/- 1.5 m m Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02.16.06 (000022) Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com