VMAA18 (6901-100016 <04>) Thank you for choosing the Sanus VMAA18 wall mount. The Sanus VMAA18 wall mount is designed to support a monitor sized up to 50 in. (127cm) and weighing up to 59 kg (130 lbs). The mount is adjustable; it will tilt +5° to -15°, swivel to ±90°, and roll ±6.° WARNING This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children! CAUTION This product is designed for use in wood stud walls only! The wall must be capable of supporting up to five times the weight of the monitor and mount combined. If you have any doubts about the ability of the wall to support the monitor, contact Sanus Customer Service, or a qualified contractor. CAUTION Do not use this product for any purpose not explicitly specified by Sanus Systems. Improper installation or use may cause personal injury and/or property damage. If you do not understand these instructions, or if you have doubts about the safety of the installation, contact Sanus Customer Service. Sanus is not liable for injury or damage caused by incorrect installation or use. Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA US Customer Service: 1-800-359-5520 · info@sanus.com · www.sanus.com ©2008 Milestone AV Technologies 3/16 in. Supplied Parts and Hardware Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the item to your dealer; contact Sanus Customer Service. Never use damaged parts! [03] x 2 [05] x 4 [01] x 1 [02] x 1 [04] x 2 5/16 in. 1/4-20 5/16-18 x 1 in. [06] x 4 [07] x 4 [08] x 2 [09] x 10 [10] x 1 M4 x 12mm M5 x 12mm M6 x 12mm M8 x 16mm 5/16 x 2.5 in. [11] x 4 001435.eps [12] x 4 [13] x 4 [14] x 4 [15] x 4 001426.eps Lag Bolt for Wall Mounts [16] x 2 M4 M5 M6 M8 M4 / M5 M6 / M8 [17] x 4 [18] x 4 [19] x 4 [20] x 4 [21] x 4 [22] x 4 [23] x 4 M4 x 30mm M5 x 30mm M6 x 35mm M8 x 40mm [24] x 4 [25] x 4 [26] x 4 [27] x 4 7/32 in. 1/4-20 x 2.0 in. 3/16 in. M4 / M5 M6 / M8 [28] x 8 [29] x 4 [30] x 4 [31] x 1 [32] x 1 6901-100016 <04> 1: Attach Brackets to Monitor For Monitors with a Flat Back [11], [12], [13], [14] 4x [17], [18], [19], [20] [28], [29] 001429.eps FPM70-Brackets not level 001427.eps FPM70-Flat and Curved Back Brackets [03] For Monitors with a Curved Back or Obstruction [11], [12], [13], [14] 4x OPT [28] [22], [23] OPT [17], [18], [19], [20] [28], [29] [03] OPT Use washer [28] with M4 or M5 hardware only. 6901-100016 <04> OPT 001428.eps FPM70-Curved Back Hardware 001429.eps FPM70-Brackets not level 001427.eps FPM70-Flat and Curved Back Brackets 2: Install Vise Assemblies [05] [30] 4x [03] [07] NOTE FPM70-Vise assemblies Do not overtighten the nut [07]. The vise assembly [05] mustinstalled rotate freely around the carriage bolt [30]. 001430.eps 3: Install Arm Assembly to Monitor 001431.eps [31] FPM70-Detail, vise installation 2x [04] [03] 2x [02] [04] 6x [03] [05] NOTE Do not overtighten the fastener in the vise assemblies [05]. Tighten only enough to prevent the tubes [04] from moving. [04] 00 FP 001438.eps FPM70-Arm Attachment Detail 0.e 142 s 00 ow Arr 6901-100016 <04> 4: Install Wall Plate 3/16 in. NOTE e to Wall This product must only be used with wood studs spaced 30 - 40 cm (12 - 16 in.) on center. [01] NOTE Do not overtighten the lag bolts [15]. Tighten only until the washer [06] is pulled firmly against the wall plate [01]. Periodic maintenance may be required. [15] [06] 6901-100016 <04> 5: Attach Arm to Wall Plate [32] HEAVY! You will need assistance with this step. [02] [01] CAUTION Avoid potential injuries or property damage! Ensure the safety bolts [08] are secure. Periodic maintenance may be required. [08] 6901-100016 <04> 6: Install Preventer [32] OPT Install the preventer [10] on the left side if you want the arm to fold to the left. Install the preventer on the right side if you want the arm to fold to the right. OPT [10] [21] 7: Install Cable Management [16] [09] [16] NOTE Be sure to leave enough slack in the cables to allow the monitor to move freely. Use the cable ties [09] and wire clips [16] to secure the cables to the brackets [03] and arm [02]. [09] [03] 6901-100016 <04> 001454.eps FPM70-Cable 8: Adjust Monitor Position [31] Adjust Level [A] 0. 142 s 00 ow Arr 001449.eps FPM70-Back of Assembly Adjust Left / Right Swivel [B] [C] [B] 0014 2 Arro 0.eps ws CAUTION Avoid potential injuries or property damage! Remove the safety bracket [B] only to adjust the swivel tension nut [C]. Be sure to replace the safety bracket after adjusting the swivel tension nut. The hex hole in the safety bracket must seat over the swivel tension nut. 6901-100016 <04> 001451.eps 001451.eps FPM70-Left / Right Angle Adjust Up / Down Pitch NOTE Adjust the pitch tension by tightening or loosening the tension knobs [D]. [D] [31] 00 Ar 142 ro 0.e ws p Extend or Retract Arm s CAUTION Avoid potential injuries or property damage! Do not remove the adjustment nut [E]; tighten or loosen only as necessary for easy arm adjustment. 001453.eps FPM70-Full 001450.eps FMP70-Up / Down Pitch [E] 6901-100016 <04> [E] 00 Arr 1420 ow .ep s s Milestone AV Technologies, Inc. and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. 6901-100016 <04> ...