User manual SEIKO DM50

DIGITAL METRONOME DM50 INSTRUCTION MANUAL NAME AND OPERATION OF PARTS Tempo setting to set " " mark at the bottom of 1. Press the selector button the display to "TEMPO". The tempo setting mode will be shown on the display. or DOWN button to set the desired tempo. 2. Press UP With each press, the tempo is increased or decreased by one, respectively. The digits move quickly by 10 tempos if the button is kept pressed. RE SE T Power button Press it to turn on and off the metronome and to change over the displays. Tempo LED display It visually represents the tempo of the metronome with the flashing of the LED. Selector button Press it to select the setting item from tempo, beat/rhythm and volume. Liquid crystal display It indicates the tempo, beat/rhythm and volume settings you have made and the current time. DOWN button UP button Press the buttons to change the setting of the item selected by . pressing the selector button Clip Use it to attach the metronome to a music stand or musical score. Speaker It gives out the tempo sound of the metronome. Reset switch Push it when the battery is replaced with a new one or when the metronome does not work properly. Beat/rhythm setting 1. Press the selector button to set " " mark at the bottom of the display to "BEAT". The beat/rhythm setting mode will be shown on the display. or DOWN button to set the desired beat/ 2. Press UP rhythm. With each press, the beat/rhythm changes one by one in the following order. 01234567 Volume setting 1. Press the selector button to set " " mark at the bottom of the display to "VOLUME". The volume setting mode will be shown on the display. or DOWN button to set the volume to the 2. Press UP desired level. With each press, the volume level changes one by one in the following order. High No sound Low Mid Time setting pressed when the power is turned off Keep the power button or when the metronome display is shown. The time display will be shown. Follow the procedure below to set the current time. pressed 1. While in the time mode, keep the selector button to show the time setting display. to select the digits to be adjusted 2. Press the selector button from hours and minutes. Press UP or DOWN button to set the desired time. 3. After the time adjustment is completed, press the power to return to the time display. button * To turn the power off, press the power button again. * If you decide not to use the metronome for a long time, it is recommended that the power is turned off to save battery energy. HOW TO USE The battery included with the metronome is a monitor battery, and its life may be shorter than the specified period. Changeover of displays POWER OFF display Press the power button . Press the power button . Keep the power button pressed. MEMORY BACKUP FUNCTION METRONOME display Keep the power button pressed. Press the power button TIME display Keep the selector button pressed. Even after the metronome is turned off, the settings you have made are stored in memory and will not be erased. is If the battery is replaced with a new one or if the reset switch pushed, the metronome will return to the following initial settings. 1. 2. 3. Tempo Beat/rhythm Volume [120] [0] [High] . TIME SETTING display When the metronome is turned off (when the display is blank), pressing the power button will turn it on. Another press of the button will turn it off again. 30 31 · · · · · 119 120 121 · · · · · 249 250 BATTERY CHANGE When the battery nears its end, the tempo LED display and the liquid crystal display become dim, and the sound becomes weak. In that case, replace the battery with a new one immediately. Otherwise, the metronome may work improperly. How to replace the battery 1. Be sure to press the power button to turn off the metronome. Screws 2. Loosen and remove the three screws fixing the rear cover. 3. Open the rear cover. 4. Remove the battery clamp screw, and take out the old battery. 5. Set the new battery inside the white Reset switch circle, checking that the (+) and (­) terminals are properly set. 6. Set the battery clamp, and tighten the screw to fix it securely. 7. Close the rear cover, and tighten Battery clamp screw the three screws to fix it. Battery clamp 8. Pinch open the clip, and push the reset switch with a tip of a ballpoint pen or something that has a sharpened tip. Be sure to perform this resetting procedure. Otherwise, the metronome may work improperly. In case the metronome does not work properly while in use, also push the reset switch to return it to normal. RE SE T * Be sure to set the (+) an (­) terminals of the battery properly. Otherwise, a malfunction will result. * When the battery is replaced with a new one, tempo, beat/rhythm and volume settings you have made are all erased. Set them as desired before using the metronome. * When disposing of the old battery, observe the regulations of the authorities concerned. * Keep the old battery and the battery hatch beyond the reach of children. If a child swallows either of them, consult the doctor immediately. SPECIFICATIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. Display Speaker Tempo range Beat/rhythm range Volume Accuracy Power supply Overall dimensions Weight : Liquid crystal display : Piezoelectric speaker : 30 ~ 250 times/min. : 0 ~ 7, : : : : : , , 4-level volume control (no sound, low, mid and high) ±3% Lithium battery CR2025, 1 piece 40 (W) x 57 (H) x 35 (D) mm Approx. 30 g (including battery) * The design and specifications are subject to change without prior notice for product improvement.