MULTIMEDIA PROJECTOR MODEL PG-MB60X SETUP GUIDE Screen Size and Projection Distance ................... 2 Connecting Pin Assignments ................................ 3 RS-232C Specifications and Commands ............. 4 Dimensions ............................................................. 6 Screen Size and Projection Distance The projection screen size varies according to the distance from the lens of the projector to the screen. Install the projector so that projected images are projected onto the screen at the optimum size by referring to the table below. Use the values in the table as a reference when installing the projector. Side View Screen H Lens center L NORMAL Mode (4:3) Diag. [ ] 300" (762 cm) 250" (635 cm) 200" (508 cm) 150" (381 cm) 100" (254 cm) 84" (213 cm) 72" (183 cm) 60" (152 cm) 40" (102 cm) : L: L1: L2: H: Picture (Screen) size Width Height 610 cm (240") 457 cm (180") 508 cm (200") 381 cm (150") 406 cm (160") 305 cm (120") 305 cm (120") 229 cm (90") 203 cm (80") 152 cm (60") 171 cm (67") 128 cm (50") 146 cm (58") 110 cm (43") 122 cm (48") 91 cm (36") 81 cm (32") 61 cm (24") Projection Minimum [L1] 9.1 m (29' 9") 7.6 m (24' 9") 6.0 m (19'10") 4.5 m (14'10") 3.0 m (9'11") 2.5 m (8' 4") 2.2 m (7' 2") 1.8 m (5'11") 1.2 m (4' 0") distance [L] Distance from the bottom of the image to the lens center [H] Maximum [L2] 13.7 m (44' 9") ­10.2 cm (­4 1/64") 11.4 m (37' 4") ­8.5 cm (­3 11/32") 9.1 m (29'10") ­6.8 cm (­2 43/64") 6.8 m (22' 5") ­5.1 cm (­2 1/64") 4.6 m (14'11") ­3.4 cm (­1 11/32") 3.8 m (12' 6") ­2.9 cm (­1 1/8") 3.3 m (10' 9") ­2.4 cm (­31/32") 2.7 m (8'11") ­2.0 cm (­51/64") 1.8 m (6' 0") ­1.4 cm (­17/32") The formula for picture size and projection distance [m/cm] [Feet/inches] L1 (ft) = 0.0302 / 0.3048 L1 (m) = 0.0302 L2 (m) = 0.0455 L2 (ft) = 0.0455 / 0.3048 H (in) = ­0.034 / 2.54 H (cm) = ­0.034 Picture size (diag.) (in/cm) Projection distance(m/ft) Minimum projection distance (m/ft) Maximum projection distance (m/ft) Distance from the bottom of the image to the lens center (cm/in) STRETCH Mode (16:9) Diag. [ ] 250" (635 cm) 225" (572 cm) 200" (508 cm) 150" (381 cm) 133" (338 cm) 106" (269 cm) 100" (254 cm) 92" (234 cm) 84" (213 cm) 72" (183 cm) 60" (152 cm) 40" (102 cm) : L: L1: L2: H: Picture (Screen) size Width Height 553 cm (218") 311 cm (123") 498 cm (196") 280 cm (110") 443 cm (174") 249 cm (98") 332 cm (131") 187 cm (74") 294 cm (116") 166 cm (65") 235 cm (92") 132 cm (52") 221 cm (87") 125 cm (49") 204 cm (80") 115 cm (45") 186 cm (73") 105 cm (41") 159 cm (63") 90 cm (35") 133 cm (52") 75 cm (29") 89 cm (35") 50 cm (20") Projection Minimum [L1] 8.2 m (27' 0") 7.4 m (24' 3") 6.6 m (21' 7") 4.9 m (16' 2") 4.4 m (14' 4") 3.5 m (11' 5") 3.3 m (10'10") 3.0 m (9'11") 2.8 m (9' 1") 2.4 m (7' 9") 2.0 m (6' 6") 1.3 m (4' 4") distance [L] Distance from the bottom of the image to the lens center [H] Maximum [L2] 12.4 m (40' 8") ­61.1 cm (­24 5/64") 11.2 m (36' 7") ­55.0 cm (­21 43/64") 9.9 m (32' 6") ­48.9 cm (­19 17/64") 7.4 m (24' 5") ­36.7 cm (­14 14/32") 6.6 m (21' 8") ­32.5 cm (­12 13/16") 5.3 m (17' 3") ­25.9 cm (­10 13/64") 5.0 m (16' 3") ­24.5 cm (­9 5/8") 4.6 m (15' 0") ­22.5 cm (­8 55/64") 4.2 m (13' 8") ­20.5 cm (­8 3/32") 3.6 m (11' 9") ­17.6 cm (­6 15/16") 3.0 m (9' 9") ­14.7 cm (­5 25/32") 2.0 m (6' 6") ­9.8 cm (­3 55/64") The formula for picture size and projection distance [m/cm] [Feet/inches] L1 (m) = 0.0329 L1 (ft) = 0.0329 / 0.3048 L2 (m) = 0.04957 L2 (ft) = 0.04957 / 0.3048 H (cm) = ­0.24459 H (in) = ­0.24459 / 2.54 Picture size (diag.) (in/cm) Projection distance(m/ft) Minimum projection distance (m/ft) Maximum projection distance (m/ft) Distance from the bottom of the image to the lens center (cm/in) Note · There may be an error of ± 3% in the above values. · Values with a minus (­) sign indicate that the lens center is lower than the bottom of the image. -2 Connecting Pin Assignments INPUT 1/INPUT 2 and OUTPUT RGB Signal Terminal: 15-pin Mini D-sub female connector RGB Input 11 15 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Video input (red) Video input (green/sync on green) Video input (blue) Not connected Not connected Earth (red) Earth (green/sync on green) Earth (blue) Not connected GND Not connected Bi-directional data Horizontal sync signal: TTL level Vertical sync signal: TTL level Data clock Component Input 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. PR (CR) Y PB (CB) Not connected Not connected Earth (PR) Earth (Y) Earth (PB) Not connected Not connected Not connected Not connected Not connected Not connected Not connected 1 6 5 10 RS-232C Terminal: 9-pin Mini DIN female connector 1 4 2 5 Pin No. 1 2 3 4 5 6 7 8 9 Signal RD SD SG RS CS Name Receive Data Send Data Signal Ground I/O Input Output Reference Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to Pin 8 Connected to Pin 7 Not connected 3 6 7 8 9 DIN-D-sub RS-232C adaptor: 9-pin D-sub male connector 1 5 Pin No. 1 2 3 4 5 6 7 8 9 Signal RD SD SG RS CS Name Receive Data Send Data Signal Ground I/O Input Output Reference Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to internal circuit Connected to internal circuit Not connected 6 9 Note · Pin 8 (CS) and Pin 7 (RS) are short circuited inside the projector. RS-232C Cable recommended connection: 9-pin D-sub female connector 5 1 Pin No. 1 2 3 4 5 6 7 8 9 Signal CD RD SD ER SG DR RS CS CI Pin No. 1 2 3 4 5 6 7 8 9 Signal CD RD SD ER SG DR RS CS CI 9 6 Note · Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. computer). Projector Pin No. 4 5 6 Computer Pin No. 4 5 6 USB Terminal: 4-pin B-type USB female connector 43 Pin No. 1 2 3 4 Signal VCC USB­ USB+ SG Name USB power USB data­ USB data+ GND 12 -3 RS-232C Specifications and Commands Computer control A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, commercially available) to the projector. (See page 27 of the projector's operation manual for connection.) Communication conditions Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate*: 9,600 bps / 115,200 bps Stop bit: 1 bit Data length: 8 bits Flow control: None *Set the projector's baud rate to the same rate as used by the computer. Basic format Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer. Command format C1 C2 C3 C4 P1 P2 P3 P4 Return code (0DH) Command 4-digit Response code format Normal response Parameter 4-digit Problem response (communication error or incorrect command) O Info K Return code (0DH) E R R Return code (0DH) · When controlling the projector using RS-232C commands from a computer, wait at least 30 seconds after the power has been turned on, and then transmit the commands. After putting the projector into standby mode, wait at least 90 seconds until the cooling fan stops, and then transmit the commands. · If more than one command will be sent to the projector, wait for projector reply before sending next command. Note · When the projector receives the following commands, the on-screen display will not disappear and these commands will not reset the "Auto Power Off" function timer when no signal is present. POWR????, TABN_ _ _1, TLPS_ _ _1, TLTT_ _ _1, TLTL_ _ _1 Commands Example: When turning on the projector, make the following setting. Computer P Standby Power On Power Status Projector Status O W R _ P P P T O O O A _ W W W B R R R N _ _ _ ? _ _ _ ? _ _ _ ? _ 0 1 ? 1 1 Return Projector O K Control Contents Command Parameter Lamp Status Volume (0-60) AV Mute : Off AV Mute : On Keystone (-127 ~ +127) INPUT 1 (RGB1) INPUT 2 (RGB2) INPUT 3 (Video) INPUT 4 (S-Video) Freeze : Off Freeze : On Auto Sync Start T V I I K I I I I F F A L O M M E R R V V R R D P L B B Y G G E E E E J S A K K S B B D D Z Z S _ _ _ _ * _ _ _ _ _ _ _ _ _ _ _ * _ _ _ _ _ _ _ _ * _ _ * _ _ _ _ _ _ _ 1 * 0 1 * 1 2 1 2 0 1 1 OK or ERR OK or ERR 0 : Standby, 1 : On 0 : Normal, 1 : Temp High, 2 : Fan Err, 8 : Lamp Life 5% or less, 16 : Lamp Burnt-out, 32 : Lamp Ignition Failure, 64 : Temp Abnormally High 0 : Off, 1 : On, 2 : Retry, 3 : Waiting, 4 : Lamp Error OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR -4 RS-232C Specifications and Commands Control Contents INPUT 1 Resize : Normal INPUT 1 Resize : Dot By Dot INPUT 1 Resize : Border INPUT 1 Resize : Stretch INPUT 2 Resize : Normal INPUT 2 Resize : Dot By Dot INPUT 2 Resize : Border INPUT 2 Resize : Stretch INPUT 3 Resize : Normal INPUT 3 Resize : Border INPUT 3 Resize : Stretch INPUT 4 Resize : Normal INPUT 4 Resize : Border INPUT 4 Resize : Stretch INPUT 1 Picture Mode : Standard INPUT 1 Picture Mode : Presentation INPUT 1 Picture Mode : Cinema INPUT 1 Picture Mode : Game INPUT 2 Picture Mode : Standard INPUT 2 Picture Mode : Presentation INPUT 2 Picture Mode : Cinema INPUT 2 Picture Mode : Game INPUT 3 Picture Mode : Standard INPUT 3 Picture Mode : Presentation INPUT 3 Picture Mode : Cinema INPUT 3 Picture Mode : Game INPUT 4 Picture Mode : Standard INPUT 4 Picture Mode : Presentation INPUT 4 Picture Mode : Cinema INPUT 4 Picture Mode : Game INPUT 1 Bright Boost (0 -10) INPUT 2 Bright Boost (0 -10) INPUT 3 Bright Boost (0 -10) INPUT 4 Bright Boost (0 -10) INPUT 1 CLR Temp *1 INPUT 2 CLR Temp *1 INPUT 3 CLR Temp *1 INPUT 4 CLR Temp *1 INPUT 1 sRGB : Off INPUT 1 sRGB : On INPUT 2 sRGB : Off INPUT 2 sRGB : On INPUT 1 Signal Type : Auto INPUT 1 Signal Type : RGB INPUT 1 Signal Type : Component INPUT 2 Signal Type : Auto INPUT 2 Signal Type : RGB INPUT 2 Signal Type : Component INPUT 1 Adjustment Reset INPUT 2 Adjustment Reset INPUT 3 Adjustment Reset INPUT 4 Adjustment Reset Command Parameter R R R R R R R R R R R R R R R R R R R R R R V V V V V V V V R R V V R R V V C C C C I I I I I I R R V V A A A A B B B B A A A B B B A A A A B B B B A A A A B B B B A B A B A B A B S S S S A A A B B B A B A B S S S S S S S S S S S S S S P P P P P P P P P P P P P P P P W W W W C C C C R R R R S S S S S S R R R R R R R R R R R R V V V V V V S S S S S S S S S S S S S S S S E E E E T T T T A A B B I I I I I I E E E E _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 * * * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ 1 3 6 2 1 3 6 2 1 3 2 1 3 2 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 * * * * * * * * 0 1 0 1 0 1 2 0 1 2 1 1 1 1 Return OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR Control Contents Auto Sync : Off Auto Sync : On Lamp Usage Time (hour) Remaining Lamp Life (Percentage) OSD Display : Off OSD Display : On Video System : Auto Video System : PAL Video System : SECAM Video System : NTSC4.43 Video System : NTSC3.58 Video System : PAL-M Video System : PAL-N Video System : PAL-60 Background : Logo Background : Blue Background : None Eco Mode : Standard Eco Mode : Eco Auto Power Off : Disable Auto Power Off : Enable Auto Keystone : Off Auto Keystone : On Speaker : Off Speaker : On Audio Out : FAO Audio Out : VAO PRJ Mode : Reverse Off PRJ Mode : Reverse On PRJ Mode : Invert Off PRJ Mode : Invert On Monitor Out : Disable Monitor Out : Enable All Reset Language : English Language : Deutsch Language : Español Language : Nederlands Language : Français Language : Italiano Language : Svenska Language : Language : Português Language : Language : Model Name Check Model Name Check 2 Command Parameter A A T T I I M M M M M M M M I I I T T A A A A A A A A I I I I M M A M M M M M M M M M M M T M A A L L M M E E E E E E E E M M M H H P P T T S S O O M M M M O O L E E E E E E E E E E E N N D D T T D D S S S S S S S S B B B M M O O K K P P U U R R I I U U R L L L L L L L L L L L A R J J T L I I Y Y Y Y Y Y Y Y G G G D D W W S S K K T T E E N N T T E A A A A A A A A A A A M D _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ...