User manual SHERWOOD NEWCASTLE P-965

P-965 A/V Tuner Pre Amplifier Introduction READ THIS BEFORE OPERATING YOUR UNIT ENGLISH This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Note to CATV System Installer : This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as pracitcal. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FOR YOUR SAFETY Units shipped to the U.S.A and Canada are designed for operation on 120 V AC only. Safety precaution with use of a polarized AC plug. However, some products may be supplied with a nonpolarized plug. U.S.A CANADA 120 V CAUTION : To prevent electric shock, match wide blade of plug to wide slot, fully insert. : Pour éviter chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu' au fond. ATTENTION · · · · · · · · Avoid high temperatures. Allow for sufficient heat dispersion when installed on a rack. Keep the set free from moisture, water, and dust. Do not let foreign objects in the set. Handle the power cord carefully. Hold the plug when unplugging the cord. Unplug the power cord when not using the set for long periods of time. Do not obstruct the ventilation holes. Do not let insecticides, benzene, and thinner come in contact with the set. Never disassemble or modify the set in any way. 2 SAFETY INSTRUCTION 1. Read Instructions - All the safety and operating instructions should be read before the product is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement, or near a swimming pool; and the like. 8. Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. 9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and PORTABLE CART WARNING to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 11. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Alternate Warnings - This product is equipped with a three-wire grounding-type plug, a plug having a third(grounding) pin. This plug will only fit into a grounding-type power outlet. this is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 13. Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure 1. Figure 1 Example of antenna grounding as per National Electrical Code, ANSI/NFPA 70 ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) NEC - NATIONAL ELECTRICAL CODE 15. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 16. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 19. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20. Damage Requiring Service - Unplug this product form the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance - this indicates a need for service. 21. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 24. Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 3 ENGLISH CONTENTS ENGLISH · Introduction READ THIS BEFORE OPERATING YOUR UNIT SAFETY INSTRUCTION | 3 |2 · System Connections · Front Panel Controls |5 | 14 · Universal Remote Controls | 16 OPERATING COMPONENTS WITH REMOTE CONTROL REMOTE CONTROL OPERATION RANGE | 19 LOADING BATTERIES | 19 ENTERING A SETUP CODE | 20 | 19 · ROOM 2 Remote Controls REMOTE CONTROL OPERATION RANGE LOADING BATTERIES | 22 | 22 · Operations LISTENING TO A PROGRAM SOURCE | 23 SURROUND SOUND | 26 ENJOYING SURROUND SOUND | 29 LISTENING TO RADIO BROADCASTS | 34 RECORDING | 37 DIGITAL AUDIO RECORDING WITH MD RECORDER OTHER FUNCTIONS | 39 ROOM 2 SOURCE PLAYBACK | 41 | 38 · Using the OSD CURRENT STATUS DISPLAY | 42 · OSD Menu Settings | 42 SETTING THE SPEAKER SETUP | 44 SETTING THE SYSTEM SETUP | 51 SETTING THE SURROUND SETUP | 58 SETTING THE CH LEVEL SETUP | 61 SETTING THE ROOM2 FEED SETUP | 64 | 66 · Troubleshooting Guide · Specifications | 67 4 System Connections ENGLISH · Pleas be certain that this unit is unplugged from the AC outlet before making any connections. · Since different components often have different terminal names, carefully read the operating instructions of the component connected. · Be sure to observe the color coding when connecting audio and video cords. · Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the unit. 3 11 7 1 13 8 9 10 4,11 6 5 4 2 3 5 12 1. CONNECTING ANTENNAS FM Indoor Antenna FM Outdoor Antenna · Change the position of the FM indoor antenna until you get the best reception of your favorite FM stations. · A 75 outdoor FM antenna may be used to further improve the reception. Disconnect the indoor antenna before replacing it with the outdoor one. AM Outdoor Antenna AM Loop Antenna AM Loop Antenna · Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC input cord and set it to a direction for the best reception. · If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of the AM loop antenna. 5 2. CONNECTING AUDIO COMPONENTS Note: · Do not connect the turntable with MC type cartridge directly. If you have it, use a separate head amplifier or set-up transformer. ENGLISH AUX CD recorder, MD recorder, etc. TAPE MONITOR Tape deck, MD recorder, etc. AUDIO L IN R AUDIO L OUT R L AUDIO R IN L AUDIO R OUT CD CD player, etc. PHONO Turntable with MM type cartridge GND AUDIO L OUT R L AUDIO R OUT · The TAPE MONITOR IN/OUT jacks may also be connected to the LINE OUT/IN jacks of an optional graphic equalizer. 3. CONNECTING VIDEO COMPONENTS · There are three types of video jacks (COMPONENT, S-VIDEO, COMPOSITE) for connecting video components. Connect them to the corresponding video jacks according to their capability. · For your reference, the excellence in picture quality is as follows : "COMPONENT" >"S-VIDEO">"COMPOSITE" . · When making COMPONENT VIDEO connections, connect "Y" to "Y", "CB" to "CB"(or "B-Y", "PB") and "CR" to "CR"(or "R-Y", "PR" ). · When connecting to video recording component such as video deck, DVD recorder, etc . or TV for ROOM 2, you must use the same type of video jacks that you did connect to video playback components such as DVD player, LD player, etc. · This unit is equipped with a function that up-converts composite video or S-Video signals to component video signals or downconverts S-Video signals to composite video signals and outputs them from the MONITOR OUTs. Because of this, one of three types of MONITOR OUT jacks can be connected to the monitor TV regardless of how the video components are connected to VIDEO IN jacks of this unit. · Connect the video components, referring to the following table. Relationship between the video input signal and video output signal Video input signals COMPONENT S-VIDEO COMPOSITE MONITOR OUTs COMPONENT Composite S-Video S-Video Component Component Component Component Composite S-Video S-Video Composite S-Video Composite S-VIDEO Composite S-Video S-Video COMPOSITE Composite S-Video Composite VIDEO 2 / ROOM 2 OUTs S-VIDEO S-Video S-Video Composite Composite S-Video S-Video Composite COMPOSITE Composite Notes : · In such a case of making only COMPONENT VIDEO connections between this unit and video component, while viewing a movie via MONITOR COMPONENT OUTs, if the OSD menu operation is performed with the OSD, CURSOR control( , , , ), ENTER buttons, etc., the picture is automatically turned off and only the OSD menu is displayed. · When S-Video signals and composite video signals are input into this unit, even though the OSD menu operation is performed, the OSD menu cannot be displayed via MONITOR COMPOSITE OUT. · When Sherwood DVD player such as V-768, etc. is connected to the DIGI-LINK jack for system control, you should connect the DVD player to the " VIDEO 2" jacks of this unit. Because, if the PLAY button, etc. is pressed on the DVD player, the VIDEO 2 is automatically selected as an input source on this unit. Then playback, etc. starts. 6 VIDEO 1 Video deck, DVD recorder, etc. Y CB CR COMPONENT OUT AUDIO OUT RL AUDIO IN RL (COMPOSITE) VIDEO OUT IN S-VIDEO OUT IN VIDEO 2 DVD player, DVD recorder, etc. Y CB CR COMPONENT OUT AUDIO OUT RL AUDIO IN RL (COMPOSITE) VIDEO OUT IN S-VIDEO OUT IN · The jacks of VIDEO 1 / VIDEO 2 may also be connected to a DVD recorder or other digital video recording component. For details , refer to the operating instructions of the component to be connected. · For ROOM 2 playback, the VIDEO 2 / ROOM 2 OUT jacks can be connected to the amplifier, TV , etc. installed in another room. (For details , refer to "ROOM 2 connections" on page 11.) VIDEO 3 DVD player, LD player, Video deck, etc. Y CB CR COMPONENT OUT AUDIO OUT RL (COMPOSITE) VIDEO OUT S-VIDEO OUT MONITOR TV, Projector, etc. Y CB CR COMPONENT IN (COMPOSITE) VIDEO IN S-VIDEO IN · The jacks of VIDEO 3 / VIDEO 4 / VIDEO 5 can also be connected to an additional video component such as a cable TV tuner, an LD player or satellite system . · Connect the jacks of VIDEO 4 / VIDEO 5 to the video components in the same way. Component video input default settings : (*) · If you connect the COMPONENT VIDEO INs to your video components, it is easier to do so following the default settings. · If your component video connections are different from the default setting , you should assign the COMPONENT VIDEO INs you used with the "When selecting the COMPONENT VIDEO SETUP" procedure on page 54. · The default settings are as follows : COMPONENT IN 1 : VIDEO 1, COMPONENT IN 2 : VIDEO 2, COMPONENT IN 3 : VIDEO 3 7 ENGLISH 4. CONNECTING DIGITAL INs and OUTs · The OPTICAL and the COAXIAL DIGITAL OUTs of the components that are connected to CD, AUX and VIDEO 1~ VIDEO 6 of this unit can be connected to these DIGITAL INs. · A digital input should be connected to the components such as a CD player, LD player, DVD player, etc. capable of outputting DTS Digital Surround, Dolby Digital or PCM format digital signals, etc. · If the component with OPTICAL or COAXIAL IN jack is connected to the OPTICAL or COAXIAL OUT jack of this unit, you can record the high quality sound of CDs , etc. without degradation. · For ROOM 2 playback, the COAXIAL DIGITAL OUT can be connected to the amplifier, etc. installed in another room.(For details, refer to "ROOM 2 connections" on page 11.) · For details, refer to the operating instructions of the component connected. · When making the COAXIAL DIGITAL connection, be sure to use a 75 COAXIAL cord, not a conventional AUDIO cord. · All of the commercially available optical fiber cords cannot be used for the equipment. If there is an optical fiber cord which cannot be connected to your equipment, consult your dealer or nearest service organization. Note : · Be sure to make either a OPTICAL or a COAXIAL DIGITAL connection on each component. (You don't need to do both.) ENGLISH PC with USB port Component with OPTICAL DIGITAL OUT Component with OPTICAL DIGITAL OUT Component with OPTICAL DIGITAL OUT Component with OPTICAL DIGITAL OUT Component such as an MD recorder, CD recorder with OPTICAL DIGITAL IN Component such as an MD recorder, CD recorder with COAXIAL DIGITAL IN Component with COAXIAL DIGITAL OUT Component with COAXIAL DIGITAL OUT USB audio connection · The USB audio connection feature allows you connect a PC to this unit to hear soundtracks from your PC. USB device controls on the computer(such as volume) may or may not work. In either case, we recommend leaving all volume controls on the computer max and controlling volume from this unit. · You may update the operating software through this USB connection in the future.(For details, refer to "CONNECTING PC FOR UPGRADES" on page 13.) Notes: · This USB terminal only supports 2 channel PCM signals. In case of other digital signals, loud noise or no sound may be heard from the speakers, and it may be harmful to your ears and damages the speakers. · The digital signals being input into this USB terminal will not be output from the COAXIAL OUT jack. · Some operating systems(OSs) may or may not work with this USB terminal. · The sound may be interrupted, degraded or played back incorrectly due to your PC settings and PC specifications. Refer to the operating instructions of your PC concerning USB devices, etc. · Don't use other applifications on your PC when playing back through this USB connection. · Sherwood cannot be held responsible for damage to your computer system, software crashes or failures or any other possible computer problems due to this configuration. · Do not disconnect the USB cable while playing a soundtrack or updating the operating software, etc. Should this happen, it may be result in malfunction or cause damage to the unit. Digital input default settings · If you connect the DIGITAL INs to your components, it is easier to do so following the default settings. · If your DIGITAL connections are different from default settings, you should assign the DIGITAL INs you used with the "When selecting the DIGITAL INPUT SETUP" procedure on page 51. · The default settings are as follows : OPTICAL IN 1 : VIDEO 1 , OPTICAL IN 2 : VIDEO 2 , OPTICAL IN 3 : VIDEO 3 , OPTICAL IN 4 : VIDEO 5 ,COAXIAL IN 1 : CD , COAXIAL IN 2 : VIDEO 4, (Front) OPTICAL IN 5 : VIDEO 6, USB : AUX 8 5. CONNECTING 8CH DIRECT INs · Use these jacks to connect the corresponding analog audio and video outputs of a DVD player or a external decoder , etc. that has 6 , 7 or 8 channel audio and video outputs. · In case of 6 or 7 channel outputs , do not connect both of the SURROUND BACK L and R inputs or the SURROUND BACK R input of this unit . (For details, refer to the operating instructions of the component to be connected. ) Decoder with 6, 7 or 8 channel outputs 8 CH DIRECT OUTs CENTER SUBWOOFER FRONT RL SURROUND SURR.BACK RL RL S-VIDEO OUT (COMPOSITE) VIDEO OUT 6. CONNECTING PREOUTs Additional powered subwoofer powered subwoofer Sherwood A-965 Power amplifiers CENTER L FRONT R L SURROUND R L SURROUND BACK R Center speaker Front speakers Surround speakers Surround back speakers · Connect the PREOUT jacks to the powered speakers or the power amplifiers connected to speakers respectively. · We recommend that you use Sherwood power amplifier A-965 for 7 channels(front L/R, center, surround L/R, surround back L/R) for easy operation and installation. · When using only one surround back speaker, connect the SURROUND BACK LEFT jack to the power amplifier. · If this is the case, you can connect the subwoofer without built-in amplifier to SURROUND BACK RIGHT terminals of the power amplifier.(For details, refer to "When selecting the SUBWOOFER" on page 47.) · To emphasize the deep bass sounds, connect a powered subwoofer. · To enjoy deeper bass sounds, connect an additional powered subwoofer to the SUBWOOFER 2 jack. Notes : · After installing the speakers , first adjust the speaker settings according to your environment and speaker layout. (For details, refer to "SETTING THE SPEAKER SETUP" on page 44.) · According to speaker settings, you cannot use either SURROUND BACK RIGHT jack or both of SURROUND BACK jacks. · For installing the speakers, refer to "Speaker placement" on page 10. 9 ENGLISH Speaker placement Ideal speaker placement varies depending on the size of your room and the wall coverings, etc. The typical example of speaker placement and recommendations are as follows : ENGLISH Front left and right speakers and center speaker · Place the front speakers with their front surfaces as flush with TV or monitor screen as possible. · Place the center speaker between the front left and right speakers and no further from the listening position than the front speakers. · Place each speaker so that sound is aimed at the location of the listener's ears when at the main listening position. Surround left and right speakers · Place the surround speakers approximately 1 meter(40 inches) above the ear level of a seated listener on the direct left and right of them or slightly behind. Surround back left and right speakers · Place the surround back speakers at the back facing the front at a narrower distance than front speakers. · When using a single surround back speaker, place it at the rear center facing the front at a slightly higher position(0 to 10 inches ) than the surround speakers. · We recommend installing the surround back speaker at a slightly downward facing angle. This effectively prevents the surround back channel signals from reflecting off the TV or screen at the front center, resulting in interference and making the sense of movement from the front to the back less sharp. 1. TV or screen 2. Front left speaker 3. Subwoofer 4. Center speaker 5. Front right speaker 6. Surround left speaker 7. Surround right speaker 8. Surround back left speaker 9. Surround back right speaker 10. Surround back center speaker 11. Listeing position Surround speaker Surround back speaker Point slightly downward Subwoofer · The subwoofer reproduces powerful deep bass sounds. Place a subwoofer anywhere in the front as desired. Notes : · When using a conventional TV, to avoid interference with the TV picture, use only magnetically shielded front left and right and center speakers. · To obtain the best surround effects, the speakers except the subwoofer should be full range speakers. Front speaker 60 to 90 cm 10 7. CONNECTING SYSTEM CONTROL · Connect this jack to the DIGI LINK jack of the external Sherwood component that uses the DIGI LINK II or III remote control system. Sherwood component with DIGI LINK II or III Tape deck System control cord DVD player 8. CONNECTING DC TRIGGER OUTs · Connect components that need to be triggered by DC under certain conditions as follows : · Connect a component to DC TRIGGER OUT 1 jack that Component to be triggered allows DC 12 V to turn on or off when this unit's power is by DC when this unit's power is turned on turned on or off. In case that this unit is connected to Sherwood power Component to be triggered amplifier A-965, connect DC TRIGGER IN jack of A-965 by DC when a specific input source is selected to DC TRIGGER OUT 1 jack for system power control. · Connect a component to DC TRIGGER OUT 2 jack that allows DC 12 V to turn on or off when a specific input source is selected or not. · For details, refer to the operating instructions of the components to be connected . · To link DC TRIGGER OUT 2 with a specific input source, refer to "When selecting the DC TRIGGER 2 SETUP" on page 55. Notes : · This output voltage (12 V d.c., 100mA ) is for (status) control only, it is not sufficient for drive capability. · When making DC TRIGGER connection, you should use the stereo mini cord, not a mono mini cord. ROOM 2 connections · ROOM 2 playback feature allows you to play a different program source in another room as well as one source in the main room at the same time. · For ROOM 2 playback, connect the VIDEO 2 / ROOM 2 OUT jacks and the COAXIAL DIGITAL OUT to the amplifier, TV. etc. installed in another room. Note : · To minimize hum or noise, use high quality connection cords. Main room This unit Another room(Room 2) IN S-VIDEO IN VIDEO TV or projector L AUDIO IN COAXIAL DIGITAL IN R Amplifier Speakers 11 ENGLISH CD player 9. CONNECTING MULTI-ROOM SYSTEM KIT · The multi-room system kit(sold separately ) is essential for operation from a remote location . For information on the multi-room system kit, contact the Xantech corporation at 1-800-843-5465 or www.xantech.com. · IR IN jack allow you to control this unit from another room with the remote control unit. · To control this unit from another room with the remote control unit, connect the IR IN jack to the output of the connecting block. · If this unit is located inside a cabinet or other enclosure where the infrared beams from the remote control unit cannot enter, then operation with the remote control unit will not be possible. In such a case, connect the IR IN jack to the output of the connecting block. · To control other compatible component from another room with the universal remote control unit, connect the IR OUT jack to the IR emitter. Note: · Remote operation may become unreliable if the IR receiver is exposed to strong light such as direct sunlight or inverted fluorescent. Main room Connecting block (Multi-room system kit) AUDIO VIDEO 2 VIDEO 5 ENGLISH Another room(Room 2) ROOM2 VIDEO 1 IR receiver (Multi-room system kit) This unit MULTI MULTI CONTROL MASTER VOLUME DVD player POWER STANDBY DECODING STEREO DIGITAL/ANALOG PURE AUDIO VIDEO INPUT SELECTOR AUDIO T.MON 8CH DIRECT ON/ OFF IR emitter (Multi-room system kit) · When this unit is located inside a cabinet. In the cabinet RNC-500 output Connecting block (Multi-room system kit) IR receiver (Multi-room system kit) This unit MULTI MULTI CONTROL MASTER VOLUME POWER STANDBY DECODING STEREO DIGITAL/ANALOG PURE AUDIO VIDEO INPUT SELECTOR AUDIO T.MON 8CH DIRECT ON/ OFF 10. CONNECTING MICROPHONE · To use Auto Speaker Setup function, connect the supplied microphone to the SETUP MIC jack.(For details, refer to "When selecting the AUTO SPEAKER SETUP" on page 49.) Notes: · Because the microphone for Auto Speaker Setup is designed for use with this receiver, do not use a microphone other than the one supplied with this unit. · After you have completed the auto speaker setup procedure, disconnect the microphone. VIDEO 4 PHONO AUX MUTE output CD VIDEO VOLUME VIDEO 3 VIDEO 6 TUNER Microphone 12 11. CONNECTING PC FOR UPGRADES · This unit incorporates USB as well as RS-232C terminal that may be used in the future to update the operating software so that it will be able to support new digital audio formats, external control by using an external device and the like. · Connect either USB or RS-232C terminal to your PC(You don't need to do both). UPGRADE switch PC with USB or RS-232C port Notes : · Be sure to set the UPGRADE switch to "SVC"(service) before updating. · This switch should be set to "OPR"(operation) during normal operation except for upgrades. If not, this unit will not operate normally. · Programming for upgrades and external control requires specialized programming knowledge and for that reason we recommend that it only be done by qualified installers. For more information on future upgrades and external control, visit the Sherwood web site at www.sherwoodamerica.com or contact your dealer. · Do not disconnect the connection cable while updating the operating software, etc. Should this happen, it may be result in malfunction or cause damage to the unit. 12. SWITCHED AC OUTLETs · These outlets are switched on(power-on mode) and off(standby mode) according to power control as follows(Maximum total capacity is 100 W, 1A). Standby mode - Switched AC outlet off Power-on mode - Switched AC outlet on 13. AC INLET · Plug the supplied AC input cord into this AC INLET and then into the wall AC outlet. Note: · Do not use an AC input cord other than the one supplied with this unit. The AC input cord supplied is designed for use with this unit and should not be used with any other device. To a wall AC outlet. 13 ENGLISH Front Panel Controls 13 14 ENGLISH 12 1 11 15 2 3 4 5 6 7 8 9 10 · To open the panel door, push gently on the lower third of the panel door. 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 1. POWER switch 2. STANDBY button/indicator 3. DECODING MODE button 4. STEREO button 5. DIGITAL/ANALOG button 6. PURE AUDIO button 7. VIDEO SELECTOR button 8. AUDIO SELECTOR button 9. TAPE MONITOR button 10. 8 CH DIRECT button 11. MASTER VOLUME CONTROL knob 12. MULTI CONTROL knob 13. REMOTE SENSOR 14. FLUORESCENT DISPLAY For details, see next page. 15. PANEL DOOR 16. DOLBY HEADPHONE button 17. DOLBY VIRTUAL SPEAKER button 18. DOLBY PL IIx button 19. DYNAMIC RANGE button 20. LABEL button 21. ENTER/MEMORY button 22. BAND button 23. TUNING UP(+)/DOWN( ) buttons 24. HEADPHONE jack 25. HEADPHONE SELECTOR button 26. CHANNEL SELECTOR button 27. DOLBY PL II MUSIC PARAMETER button 28. CINEMA EQ button 29. TONE MODE button 30. ROOM 2 button 31. FM MODE button 32. PRESET UP(+)/DOWN(-) buttons 33. VIDEO 6 INPUT jacks For details, see next page. 14 FLUORESCENT DISPLAY 1 2 3 4 5 67 3 8 DOLBY H DIGITAL EX VIRTUAL DIRECT AUTO L C R PCM PRO LOGIC MPEG PURE SL SW SR LFE SB ANALOG SOUND TAPE MON STEREO DIGITAL RE-MASTERING DTS ES 96/24 NEO:6 Z VIDEO SET 123456 R2 MUTE CINE-EQ MEMORY 9 19 20 21 22 23 TUNED PRESET AP-SW 10 11 12 13 14 15 16 17 18 1. CHANNEL indicators 2. PCM SIGNAL indicator 3. SURROUND MODE indicators 4. TAPE MONITOR indicator 5. DIRECT indicator 6. STEREO indicator 7. AUTO indicator 8. SLEEP indicator 9. VIDEO INPUT indicators 10. MPEG SIGNAL indicator 11. PURE AUDIO indicator 12. ANALOG INPUT indicator 13. DIGITAL INPUT indicator 14. Input, frequency, volume level, operating information, etc. 15. RE-MASTERING indicator 16. TUNED indicator 17. PRESET indicator 18. ROOM 2 indicator 19. MUTE indicator 20. CINEMA EQ indicator 21. MEMORY indicator 22. SPEAKER indicator 23. SUBWOOFER indicators VIDEO 6 INPUT JACKS VIDEO 6 OPTICAL IN5 S-VIDEO VIDEO L - AUDIO - R · The VIDEO 6 input jacks may be also connected to an additional video component such as a camcorder, a video game player, etc. · If the OPTICAL IN 5 is connected to the component connected to VIDEO 6, it is easier to do so following the default settings.(For details, refer to "Digital input default settings" on page 8.) · If the OPTICAL IN 5 connection is different from the default settings, you should assign the DIGITAL INs you used with the "When selecting the DIGITAL INPUT SETUP" procedure on page 51. OPTICAL S-VIDEO DIGITAL OUT OUT VIDEO OUT LR AUDIO OUT VIDEO 6 Camcorder, video game player, etc. 15 ENGLISH Universal Remote Controls ENGLISH This universal remote control can operate not only this unit but also most popular brands of audio and video components such as CD players, DVD players, tape decks, TVs, VCRs, satellite receivers, cable boxes, etc. · To operate 8 components other than this unit, you should enter the setup code for each component. (For details, refer to "ENTERING A SETUP CODE" on page 20) · The numbered buttons on the remote control have different functions in different device modes. For details, refer to "FUNCTION TABLE of the NUMBERED BUTTONS" on the next page. Note : · This section explains the basic operations to control this unit and other Sherwood components with this remote control. For various and convenient functions of this remote control, refer to the operating manual inclosed with this remote control. DIGI LINK system remote controls This remote control can also operate Sherwood compatible components bearing the DIGI LINK(II or III) logo. · For DIGI LINK system remote control operation, first make the DIGI LINK connections between Sherwood components. · In the DIGI LINK III remote control system, if pressing PLAY, etc. on CD player or tape deck, CD or TAPE MONITOR is selected automatically on the unit without selecting the input source. Then PLAY, etc. starts. STANDBY POWER ON LCD SCREEN POWER ON button LIGHT button Activates the backlighting of the remote control for a specified time(up to 99 sec.) If any other button is pressed while the backlighting is on, the remote control will remain backlit for an additional period. STANDBY button LCD(FUNCTION) buttons MAIN AUD1 AUD2 CD DVD TAPE TV VCR SAT CABLE AUD1 MAIN button Enters the MAIN menu mode. AUX PAGE button While displaying the page menu of the selected device or the favorite channel menu, each time this button is pressed, its page changes. PA GE LCD(FUNCTION) buttons FAV FAVORITE button Enters the favorite channel mode. Each time this button is pressed, its page changes. MAIN CH. SEL VOLUME UP/DOWN( / ) buttons VOL MUTE CH/ ADJUST DECODE DSP DSP CHANNEL LEVEL / ADJUST UP/DOWN( / ) buttons CURSOR CONTROL( ENTER( ) buttons RETURN STEREO ), NUMERIC(1~0) buttons 1 4 7 DISP 2 5 8 0 M2 3 6 9 OSD/MENU ENT MACRO buttons To operate a macro function, press the corresponding MACRO button. MI M3 RNC-510 16 FUNCTION TABLE of the NUMBERED BUTTONS. Device to be controlled Button symbol POWER ON AUDIO 1("AUD1") (for receiver, "001") POWER ON AUDIO 2("AUD2") (for receiver, "001") POWER ON STANDBY CHANNEL SELECTOR ) CH LEVEL/ADJUST UP( ) CD (for CD player, "001") )> TV (for TV, "001") STANDBY STANDBY CH. SEL STANDBY PREVIOUS CHANNEL CHANNEL UP( CHANNEL DOWN( VOLUME UP( ) VOLUME DOWN( ) MUTE SURROUND MODE LANGUAGE CURSOR CONTROL ENTER 0~9 MENU SLEEP CAPTION AUTO SET ADD/ERASE PIP SWAP SOURCE STILL ) ) CHANNEL SELECTOR CH LEVEL/ADJUST UP( CH/ ADJUST CH LEVEL/ADJUST DOWN( ) CH LEVEL/ADJUST DOWN( ) VOLUME UP( ) VOL VOLUME UP( ) VOLUME DOWN( ) MUTE DECODING MODE DSP MODE UP( ) DSP MODE DOWN( ) RETURN STEREO CURSOR CONTROL ENTER 0~9 DISPLAY OSD SLEEP DIMMER ROOM 2 TEST TONE OSD DIGITAL/ANALOG SURROUND A/B SURROUND BACK PURE AUDIO PL II MUSIC PARAMETER SEARCH MODE PTY SELECT MEMORY TUNING UP(+) TUNING DOWN(-) EON TA EON PTY PRESET SCAN PRESET UP(+) PRESET DOWN(-) PLAY FORWARD SKIP REVERSE SKIP PAUSE STOP 0~9 PLAY REVERSE SKIP STOP REPEAT A< >B PAUSE FORWARD SKIP INTRO SCAN FORWARD PLAY FAST FORWARD REWIND PAUSE RECORD STOP <0~9> DECK SELECTOR A REVERSE PLAY RECORD REWIND STOP DECK SELECTOR B FORWARD PLAY PAUSE FAST FORWARD VOLUME DOWN( ) MUTE MUTE DECODING MODE DSP MODE UP( ) DECODE DSP DSP DSP MODE DOWN( ) RETURN RETURN STEREO STEREO CURSOR CONTROL ENTER 0 DISP 9 0~9 DISPLAY OSD TUNER CD TAPE MONITOR AUX PHONO VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 DTS DOLBY DIGITAL PCM MPEG 8 CH DIRECT("7.1 IN") PL II MOVIE PL II MUSIC NEO 6 CINEMA NEO 6 MUSIC OSD/MENU ENT (Left 1) (Left 2) (Left 3) P (Left 4) A (Left 5) G (Right 1) E (Right 2) 1 (Right 3) (Right 4) (Right 5) (Left 1) (Left 2) (Left 3) P A G E 2 (Left 4) (Left 5) (Right 1) (Right 2) (Right 3) (Right 4) (Right 5) Notes : · To control this unit completely with this remote control, you should use "AUD 1" and "AUD 2" both and "001" should be entered respectively as their setup codes. · The functions in < > work for this unit, not for the CD player or tape deck. 17 ENGLISH POWER ON Continued Device to be controlled Button symbol POWER ON DVD(for DVD player) V-768, etc.("001") POWER ON VD-4106, etc.("091") POWER PLAY FORWARD SKIP REVERSE SKIP FORWARD SEARCH REVERSE SEARCH PAUSE RETURN STOP CURSOR CONTROL ENTER/SELECT 0~9 DISPLAY SETUP TITLE AUDIO SUBTITLE SOUND OPEN/CLOSE ZOOM SEARCH REPEAT A< >B REPEAT MARKER RESUME RANDOM ANGLE PROGRAM CLEAR REVERS SLOW FORWARD SLOW VD-8300, etc.("116") POWER DIGEST VOLUME UP( VOLUME DOWN( PLAY/PAUSE FORWARD SKIP REVERSE SKIP FORWARD SEARCH REVERSE SEARCH STEP STOP/RETURN CURSOR CONTROL ENTER/SELECT 0~9 DISPLAY SETUP TITLE AUDIO SUBTITLE 3D SOUND OPEN/CLOSE ZOOM PBC REPEAT A< >B REPEAT MARKER SHUFFLE ANGLE PROGRAM CLEAR ) ) ENGLISH STANDBY STANDBY CH. SEL - CH/ ADJUST VOL MUTE PLAY FORWARD SKIP DECODE DSP DSP REVERSE SKIP FORWARD SEARCH REVERSE SEARCH PAUSE RETURN RETURN STOP STEREO CURSOR CONTROL ENTER 0 DISP 9 0~9 DISPLAY MENU SETUP TITLE AUDIO SUBTITLE DISC SKIP OPEN/CLOSE ZOOM SEARCH REPEAT A< >B REPEAT MODE MARKER INTRO SCAN RANDOM SUBTITLE ANGLE PROGRAM CLEAR TIME SLOW PAL/NTSC OSD/MENU ENT (Left 1) (Left 2) (Left 3) P (Left 4) A (Left 5) G (Right 1) E (Right 2) 1 (Right 3) (Right 4) (Right 5) (Left 1) (Left 2) (Left 3) P A G E 2 (Left 4) (Left 5) (Right 1) (Right 2) (Right 3) (Right 4) (Right 5) Notes : · Some functions for each component may not be available or may work differently . · For details about functions , refer to the operating instructions of each component . 18