User manual SHERWOOD R-772

R-772(A)2007.8.165:21PM 1 R-772(A)2007.8.165:21PM 2 SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should be read before the product is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement, or near a swimming pool; and the like. 8. Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. 9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from PORTABLE CART WARNING overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 11. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Alternate Warnings - This product is equipped with a three-wire grounding-type plug, a plug having a third(grounding) pin. This plug will only fit into a grounding-type power outlet. this is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 13. Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure 1. ENGLISH 15. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 16. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 19. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20. Damage Requiring Service - Unplug this product form the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance - this indicates a need for service. 21. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 24. Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 2 R-772(A)2007.8.165:21PM 3 Introduction READ THIS BEFORE OPERATING YOUR UNIT This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Caution regarding installation Note : For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure. Do not block ventilation openings or stack other equipment on the top. Note to CATV System Installer : This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FOR YOUR SAFETY Units shipped to the U.S.A and CANADA are designed for operation on 120 V AC only. Safety precaution with use of a polarized AC plug. However, some products may be supplied with a nonpolarized plug. U.S.A CANADA 120 V CAUTION : To prevent electric shock, match wide blade of plug to wide slot, fully insert. Pour éviter chocs introduire la la plus ATTENTION : correspondante deélectriques,pousser jusqu'lamefond. large de la fiche dans la borne la prise et au CAUTION · Leave a space around the unit for sufficient ventilation. · Avoid installation in extremely hot or cold locations, or in an area that is exposed to direct sunlight or heating equipment. · Keep the unit free from moisture, water, and dust. · Do not let foreign objects in the unit. · The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. · No naked flame sources, such as lighted candles, should be placed on the unit. · Please be care the environmental aspects of battery disposal. · The unit shall not be exposed to dripping or splashing for use. · No objects filled with liquids, such as vases, shall be placed on the unit. · Do not let insecticides, benzene, and thinner come in contact with the set. · Never disassemble or modify the unit in any way. Notes on the AC power cord and the wall outlet. · The unit is not disconnected from the AC power source(mains) as long as it is connected to the wall outlet, even if the unit has been turned off. · When disconnecting the power cord from the wall outlet, always pull the plug, not the power cord. · Disconnect the plug from the wall outlet when not using the unit for long periods of time. · The wall outlet shall be installed near the unit and shall be easily accessible. 3 ENGLISH R-772(A)2007.8.165:21PM 4 CONTENTS ENGLISH · SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 · Introduction READ THIS BEFORE OPERATING YOUR UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 · System Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 · Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 · Universal Remote Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 OPERATING COMPONENTS WITH REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . 19 REMOTE CONTROL OPERATION RANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 LOADING BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 USING FUNCTIONS OF REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 · ROOM 2 Remote Controls REMOTE CONTROL OPERATION RANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 LOADING BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 · Operations LISTENING TO A PROGRAM SOURCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 SURROUND SOUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 ENJOYING SURROUND SOUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 LISTENING TO RADIO BROADCASTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 LISTENING TO XM SATELLITE RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 (XM Satellite Radio (only for North America)) OTHER FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 ROOM 2 SOURCE PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 DIGITAL AUDIO RECORDING WITH MD RECORDER . . . . . . . . . . . . . . . . . . . . . . . . . 46 · OSD Menu Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 SETTING THE SYSTEM SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 SETTING THE INPUT SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 SETTING THE SPEAKER / ROOM EQ SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 SETTING THE CH LEVEL SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 SETTING THE SOUND PARAMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 SETTING THE MULTI ROOM SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 · Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 · Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 · Setup Code Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 4 R-772(A)2007.8.165:21PM 5 System Connections ENGLISH · Pleas be certain that this unit is unplugged from the AC outlet before making any connections. · Since different components often have different terminal names, carefully read the operating instructions of the component connected. · Be sure to observe the color coding when connecting audio, video and speaker cords. · Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver. 1. CONNECTING ANTENNAS · Change the position of the FM indoor antenna until you get the best reception of your favorite FM stations. · A 75 outdoor FM antenna may be used to further improve the reception. Disconnect the indoor antenna before replacing it with the outdoor one. · Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC input cord and set it to a direction for the best reception. · If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of the AM loop antenna. 5 R-772(A)2007.8.165:21PM 6 2. CONNECTING VIDEO COMPONENTS · The jacks of VIDEO 1 may also be connected to a DVD recorder or other digital video recording component. For details, refer to the operating instructions of the component to be connected. · The jacks of VIDEO 2/VIDEO 3 can also be connected to an additional video component such as a cable TV tuner or satellite system. · Connect the jacks of VIDEO 3 to the video component in the same way. ENGLISH · There are three types of video jacks (COMPONENT, SVIDEO, (composite) VIDEO) for analog video connections and the HDMI connectors for digital video and audio connections. Connect them to the corresponding video jacks according to their capability. · For your reference, the excellence in picture quality is as follows : "HDMI" > "COMPONENT" > "S-VIDEO" > "(composite) VIDEO" . · When making COMPONENT VIDEO connections, connect "Y" to "Y", "PB/CB" to "CB"(or "B-Y", "PB") and "PR/CR" to "CR"(or "R-Y", "PR"). · When recording video program sources through VIDEO 1 OUT jacks or viewing ROOM 2 source through ROOM 2 OUT jacks, you must use the same type of video jacks that you did connect to video playback components such as DVD player, cable TV tuner, etc. · This unit is equipped with a function that up-converts composite video or S-Video signals to component video signals or down-converts S-Video signals to composite video signals and outputs them from the MONITOR OUTs. Because of this, you need not connect all the types of the MONITOR OUT jacks to the MONITOR TV. · After connecting the video components, you should set the video mode correctly, referring to the following table on page 7. (For details, refer to "When selecting the VIDEO MODE" on page 54.) 6 R-772(A)2007.8.165:21PM 7 Continued Relationship between the video input signal and the video output signal Video input signals COMPONENT × × × × × × × S-VIDEO × × × × × × × (COMPOSITE) VIDEO × × × Video Mode Setting Auto Component *1 S-Video*2 Composite*2 Auto Auto Auto Auto Auto Auto COMPONENT Component Component S-Video Composite video Component Component Component*4 S-Video S-Video Composite video MONITOR OUTs S-VIDEO S-Video × (COMPOSITE) VIDEO Composite video*3 S-Video Composite video S-Video Composite video × × S-Video Composite video S-Video Composite video × S-Video S-Video Composite video Composite video*3 S-Video Composite video *1 : Component video signal can be output from the COMPONENT MONITOR OUT jacks only. In this case, the OSD menu and the momentary OSD cannot be displayed. *2 : The video signal set in the VIDEO MODE menu can be output from all the types of MONITOR OUT jacks. *3 : The OSD menu and the momentary OSD cannot be displayed via (COMPOSITE) VIDEO MONITOR OUT jack. *4 : If the OSD menu operation is performed, the picture is automatically turned off and only the OSD menu is displayed via COMPONENT MONITOR OUT jacks. Note : · When outputting the component video signal from the COMPONENT MONITOR OUT jacks as it was input, the momentary OSD cannot be displayed. HDMI (High Definition Multimedia Interface) connection : (*1) · You can connect the source component (DVD player, etc.) to the display component (TV, projector, etc.) through this receiver with using a commercially available HDMI cord. · The HDMI connection can carry uncompressed digital video signals and digital audio signals. · The HDMI video stream signals (video signals) are theoretically compatible with DVI-D. When connecting to a TV monitor, etc., equipped with DVI-D connector, it is possible to connect using a commercially available HDMI-DVI converter cord. Since the HDMI-to-DVI connection cannot carry any audio signals, you should make audio connections to play the audio signals on the component equipped with DVI-D connector. (For details, refer to the operating instructions of its.) · If you connect the HDMI INs to your video components, it is easier to do so following the default settings. · If your HDMI connection is different from the default setting, you should assign the HDMI INs you used with the "When selecting the HDMI ASSIGN" procedure on page 54. · The default settings are as follows : HDMI 1 : VIDEO 1, HDMI 2 : VIDEO 2 Copyright protection system · This unit supports HDCP (High-bandwidth Digital Contents Protection), technology to protect copyright of digital video signals against illegal duplication. HDCP must also be supported on the components connected to this unit. · This unit is HDMI Ver. 1.3 compatible. · HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC. Notes : · For stable signal transfer, we recommend using HDMI cords that are a maximum of 5 meters in length. · Among the components that support HDMI, some components can control other components via the HDMI connector. However, this unit cannot be controlled by another component via the HDMI connector. · The audio signals from the HDMI connector (including the sampling frequency and bit length) may be limited by the component that is connected. · The video signals will not be output properly if a component incompatible with HDCP is connected. · If the resolutions of the video signals which are output from the HDMI MONITOR OUT and your monitor TV are not matched, the picture is not clear, natural or displayed. In this case, change the setting of the resolution on the source component (DVD player, etc.) to one which the monitor TV can handle. (For details, refer to the operating instructions of the source component.) · When you want to enjoy only the picture on your TV, not the sound, you should set the HDMI AUDIO OUT to OFF not to output the digital audio signal from the HDMI MONITOR OUT of this receiver. (For details, refer to "When selecting the HDMI AUDIO OUT" on page 50.) Component video input default settings: (*2) · If you connect the COMPONENT VIDEO INs to your video components, it is easier to do so following the default settings. · If your component video connections are different from the default setting, you should assign the COMPONENT VIDEO INs you used with the "When selecting the VIDEO ASSIGN" procedure on page 54. · The default settings are as follows: COMPONENT IN 1 : VIDEO 1, COMPONENT IN 2 : VIDEO 2. 7 ENGLISH R-772(A)2007.8.165:21PM 8 3. CONNECTING AUDIO COMPONENTS · For analog audio recording, the ROOM 2 OUT jacks can be connected to audio recording equipment such as a tape deck, an MD recorder, etc. as shown beside. ENGLISH 4. CONNECTING EXTERNAL INS · Use these jacks to connect the corresponding outputs of a DVD player or external decorder, etc. that has 6, 7 or 8 channel analog audio outputs. · In case of 6 or 7 channel outputs, do not connect both of the SURROUND BACK L and R inputs or the SURROUND BACK R input of this unit. (For details, refer to the operating instructions of the component to be connected.) 5. CONNECTING XM (only for North America) · Connect the XM terminal to the XM Mini-Tuner system (sold separately). · Position the XM Mini-Tuner system near a south-facing window to receive the best signal. When making connections, also refer to the operating instructions of the XM Mini-Tuner system. · For the best reception, check the signal strength of the XM radio signal with using signal strength display mode, then adjust the position of the XM Mini-Tuner system until "GOOD" is displayed. (For details, refer to "Displaying XM information" on page 42.) · To listen to XM Satellite Radio, refer to "XM Satellite Radio (only for North America)" on page 40. 8 R-772(A)2007.8.165:21PM 9 6. CONNECTING DIGITAL INS AND OUT · The OPTICAL and the COAXIAL DIGITAL OUTs of the components that are connected to this unit can be connected to these DIGITAL INs. · A digital input should be connected to the components such as a CD player, DVD player, etc. capable of outputting DTS Digital Surround, Dolby Digital or PCM format digital signals, etc. · If the component with OPTICAL IN jack is connected to the OPTICAL OUT jack of this unit, you can record the high quality sound of CDs, etc. without degradation. · For details, refer to the operating instructions of the component connected. · When making the COAXIAL DIGITAL connection, be sure to use a 75 COAXIAL cord, not a conventional AUDIO cord. · All of the commercially available optical fiber cords cannot be used for the equipment. If there is an optical fiber cord which cannot be connected to your equipment, consult your dealer or nearest service organization. Notes: · Be sure to make either a OPTICAL or a COAXIAL DIGITAL connection on each component. (You don't need to do both.) · Depending on the digital audio signal format input into HDMI IN connector, some digital signals cannot be output from the OPTICAL OUT jack. Digital input default settings · If you connect the DIGITAL INs to your components, it is easier to do so following the default settings. · If your DIGITAL connections are different from default settings, you should assign the DIGITAL INs you used with the "When selecting the AUDIO ASSIGN" procedure on page 54. · The default settings are as follows : OPTICAL IN 1 : VIDEO 1, OPTICAL IN 2 : VIDEO 2, COAXIAL IN 1 : CD, COAXIAL IN 2 : AUX. 7. CONNECTING DC TRIGGER OUT · Connect a component to DC TRIGGER OUT jack that allows DC 12V to turn on when a specific input source is selected. · For details, refer to the operating instructions of the components to be connected. · To link DC TRIGGER OUT with a specific input source, refer to "When selecting the DC TRIGGER" on page 55. Notes: · This output voltage (12V d.c., 100mA) is for (status) control only, it is not sufficient for drive capability. · When making DC TRIGGER connection, you should use the stereo mini cord, not a mono mini cord. 8. CONNECTING SUBWOOFER PREOUT · To emphasize the deep bass sounds, connect a powered subwoofer. 9 ENGLISH R-772(A)2007.8.165:21PM 10 9. CONNECTING SPEAKERS · Be sure to connect speakers firmly and correctly according to the channel(left and right) and the polarity (+ and -). If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connection is incorrect, the sound will be unnatural and lack bass. · For installing the speakers, refer to "Speaker placement" on page 11. · After installing the speakers, first adjust the speaker settings according to your environment and speaker layout. (For details, refer to "SETTING THE SPEAKER/ROOM EQ SETUP" on page 57.) Surround back speakers · When using only one surround back speaker, you should connect it to SURROUND BACK/MULTI LEFT channel. · Because this receiver cannot drive the surround back speakers and the ROOM 2 speakers simultaneously, you should assign their power amplifier correctly depending on how to use them. (For details, refer to "CONNECTING ROOM 2 OUTS" on page 12 and "When selecting the AMP ASSIGN" on page 49.) Front Bi-Amp Connections. · Some speakers are equipped with two sets of input terminals, for bi-amplification. · If no other surround back speakers are used, you can connect the FRONT and the SURROUND BACK/MULTI channels to the bi-amp-capable speakers. (For details, refer to the operating instructions of your bi-amp-capable speakers.) · To drive the bi-amp-capable speakers, you should assign the power amplifier to "BI-AMP". Note : · Before making bi-amp connections, remove the short-circuiting bars from the terminals of your speakers. Caution : · Be sure to use the speakers with the impedance of 6 ohms or above. · Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers. ENGLISH 10 R-772(A)2007.8.165:21PM 11 Speaker placement Ideal speaker placement varies depending on the size of your room and the wall coverings, etc. The typical example of speaker placement and recommendations are as follows : Front left and right speakers and center speaker · Place the front speakers with their front surfaces as flush with TV or monitor screen as possible. · Place the center speaker between the front left and right speakers and no further from the listening position than the front speakers. · Place each speaker so that sound is aimed at the location of the listener's ears when at the main listening position. Surround left and right speakers · Place the surround speakers approximately 1 meter (40 inches) above the ear level of a seated listener on the direct left and right of them or slightly behind. Surround back left and right speakers · Place the surround back speakers at the back facing the front at a narrower distance than front speakers. · When using a single surround back speaker, place it at the rear center facing the front at a slightly higher position (0 to 20 cm ) than the surround speakers. · We recommend installing the surround back speaker(s) at a slightly downward facing angle. This effectively prevents the surround back channel signals from reflecting off the TV or screen at the front center, resulting in interference and making the sense of movement from the front to the back less sharp. Subwoofer · The subwoofer reproduces powerful deep bass sounds. Place a subwoofer anywhere in the front as desired. Notes : When using a conventional TV, to avoid interference with the TV picture, use only magnetically shielded front 1. TV or Screen 2. Front left speaker 3. Subwoofer 4. Center speaker 5. Front right speaker 6. Surround left speaker 7. Surround right speaker 8. Surround back left speaker 9. Surround back right speaker 10. Surround center speaker 11. Listening position left and right and center speakers. To obtain the best surround effects, the speakers except the subwoofer should be full range speakers. 11 ENGLISH R-772(A)2007.8.165:21PM 12 10. CONNECTING ROOM 2 OUTS · ROOM 2 playback feature allows you to play a different program source in another room as well as one source in the main room at the same time. · For ROOM 2 playback, connect the ROOM 2 OUT jacks to the amplifier, TV, etc. installed in another room, or connect the ROOM 2 speaker terminals to the speakers. · Because this receiver cannot drive the surround back speakers and the ROOM 2 speakers simultaneously, you should assign their power amplifier correctly depending on how to use them. (For details, refer to "When selecting the AMP ASSIGN" on page 49.) · When the ROOM 2 (AUDIO) OUT jacks are not connected to the ROOM 2 amplifier, you can connect these jacks to audio recording equipment such as a tape deck, an MD recorder, etc. for analog audio recording. (For details, refer to "CONNECTING AUDIO COMPONENTS" on page 8.) Notes : · To minimize hum or noise, use high quality connection cords. · You cannot use the digital audio signal for ROOM 2 playback. ENGLISH 11. CONNECTING RF REMOTE ANTENNA · Connect the supplied antenna to receive the RF (Radio Frequency) beams from the universal remote control. · If the antenna is connected to this receiver, even though there are obstacles such as walls, furniture, etc. in the way, you can control this receiver with the universal remote control. Therefore, you can control this receiver from another room with the universal remote control without connecting the multi-room system kit. (For details, refer to "CONNECTING MULTI-ROOM SYSTEM KIT" on page 13.) Note: · If the walls are too thick or the distance exceeds the operation range, you cannot control this receiver with the universal remote control. In such a case, connect the multi-room system kit to this receiver and set the transmission signal mode to "IR"(Infrared). (For details, refer to "Changing the transmission signal" on page 28.) 12 R-772(A)2007.8.165:21PM 13 12. CONNECTING MULTI-ROOM SYSTEM KIT · The multi-room system kit(sold separately ) is essential for operation from a remote location . For information on the multi-room system kit, contact the Xantech corporation at 1-800-843-5465 or www.xantech.com. · IR IN jack allows you to control this receiver from another room with the remote control unit. · To control this receiver from another room with the remote control unit, connect the IR IN jack to the output of the connecting block. · If this receiver is located inside a cabinet or other enclosure where the signals from the remote control unit cannot enter, then operation with the remote control unit will not be possible. In such a case, connect the IR IN jack to the output of the connecting block. Notes: · Remote operation may become unreliable if the IR receiver is exposed to strong light such as direct sunlight or inverted fluorescent. · When the transmission signal mode is set to "RF", the IR receiver cannot accept the RF beams from the universal remote control and remote operation will become unreliable. 13. CONNECTING PC FOR UPGRADES · This receiver incorporates USB as well as RS-232C terminal that may be used in the future to update the operating software so that it will be able to support new digital audio formats, external control by using an external device and the like. · Connect either USB or RS-232C terminal to your PC (you don't need to do both). Notes: · Programming for upgrades and external control requires specialized programming knowledge and for that reason we recommend that it only be done by qualified installers. For more information on future upgrades and external control, visit the Sherwood web site at www.sherwoodamerica.com or contact your dealer. · Do not disconnect the connection cable while updating the operating software, etc. Should this happen, it may be result in malfunction or cause damage to the unit. 13 ENGLISH R-772(A)2007.8.165:21PM 14 14. SWITCHED AC OUTLETS · These outlets are switched on (power-on mode) and off (standby mode) according to power control as follows (Maximum total capacity is 120 W (1A)). Standby mode - Switched AC outlet off Power - on mode - Switched AC outet on ENGLISH 15. AC INPUT CORD · Plug this cord into a wall AC outlet. 14 R-772(A)2007.8.165:21PM 15 Front Panel Controls 1. POWER switch 2. POWER ON/STANDBY button/indicator 3. VIDEO INPUT SELECTOR button 4. AUDIO INPUT SELECTOR button 5. EXTERNAL IN button 6. TUNER button 7. MASTER VOLUME CONTROL knob 8. HEADPHONE jack 9. SPEAKER button/indicator 10. SURROUND MODE button 11. STEREO button 12. SETUP button 13. CHANNEL LEVEL button 14. CONTROL UP/DOWN (/) buttons 15. ROOM 2 button 16. MEMORY/ENTER button 17. TUNING UP/DOWN(+/-) buttons 18. PRESET UP/DOWN(+/-) buttons 19. AUDIO ASSIGN button 20. MULTI CONTROL knob 21. REMOTE SENSOR 22. FLUORESCENT DISPLAY For details, see below. 23. SETUP MIC jack For details, see next page. 24. AUX IN jack For details, see next page. 25. VIDEO 4 IN jacks For details, see next page. FLUORESCENT DISPLAY 1. Input, frequency, volume level, operating information, etc. 2. Surround mode indicators 3. AUTO indicator 4. DIGITAL INPUT indicator 5. DIRECT indicator 6. Preset number, sleep time display 7. MEMORY indicator 8. PRESET indicator 9. SLEEP indicator 10. ROOM 2 indicator 11. TUNED indicator 12. STEREO indicator 15 ENGLISH R-772(A)2007.8.165:21PM 16 SETUP MIC JACK · To use Auto Setup function, connect the supplied microphone to the SETUP MIC jack.(For details, refer to "When selecting the AUTO SETUP" on page 57.) ENGLISH Notes: · Because the microphone for Auto Setup is designed for use with this receiver, do not use a microphone other than the one supplied with this receiver. · After you have completed the auto setup procedure, disconnect the microphone. AUX IN JACK · The AUX IN jack can be connected to an additional audio component such as an MP3 player, etc. Note : · When connecting this jack to an MP3 player, etc., you should use the stereo mini cord, not a mono mini cord. VIDEO 4 IN JACKS · The VIDEO 4 IN jacks may be also connected to an additional video component such as a camcorder, a video game player, etc. 16 R-772(A)2007.8.165:21PM 17 Universal Remote Controls This universal remote control can operate not only this receiver but also most popular brands of audio and video components such as CD players, tape decks, TVs, cable boxes, VCRs, DVD players, satellite receivers, etc. · To operate 7 components other than this receiver , you should enter the setup code for each component. (For details, refer to "USING FUNCTIONS OF REMOTE CONTROL" on page 20.) · The numbered buttons on the remote control have different functions in different device modes. For details, refer to "FUNCTION TABLE of the NUMBERED BUTTONS" on the next page. About the transmission signal This remote control can emit not only the infrared beams which the conventional remote control(inculding the ROOM 2 remote control) uses but also the RF(Radio Frequency) beams which are stronger than those. To operate this receiver and other components, this remote control should emit the infrared beams. To operate this receiver only from longer distance even if there are obstacles such as walls, furniture, etc. in the way, this remote control should emit the RF beams. Therefore, depending on how to use this remote control, you should set the tansmission signal mode to "IR"(default value) or "RF". (For details, refer to "Changing the transmission signal" on page 28.) Notes : · To receive the RF beams, you should connect the RF remote antenna to this receiver. (For details, refer to "CONNECTING RF REMOTE ANTENNA" on page 12.) · If the transmission signal mode is set to "RF", this remote control cannot control other audio and video components. 17 ENGLISH R-772(A)2007.8.165:21PM 18 FUNCTION TABLE of the NUMBERED BUTTONS. ENGLISH Notes : · Some functions for each component may not be available or may work differently. · Depending on other kinds of components that are available for each DEVICE button, some functions may not be available or may work differently, too. · For details about functions, refer to the operating instructions of each component. 18 R-772(A)2007.8.165:21PM 19 OPERATING COMPONENTS WITH REMOTE CONTROL REMOTE CONTROL OPERATION RANGE In case that this remote control emits the infrared beams · Use the remote control within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor. 1. Enter the setup code for each component other 2. Turn on the component you want to operate. 3. Press the DEVICE button on the remote control corresponding to the component you wish to operate. 4. Aim the remote control at the REMOTE SENSOR of the component you wish to control and press the button corresponding to the operation you want. Note : · When you cannot operate any component, check if the transmission signal mode is set to "RF". (For details, refer to "Changing the transmission signal" on page 28.) In case that this remote control emits the RF beams · Use the remote control within a disatance of about 10 meters (33 feet) toward this receiver. LOADING BATTERIES When the remote control does not operate, the old batteries should be replaced. In this case, load new batteries within several minutes after removing old batteries. If the betteries are removed or have been exhausted for a longer period of time, memorized contents will be cleared. Should this happen, you should memorize them again. 1. Remove the cover. 2. Load four alkaline batteries ("AAA" size, 1.5V) matching the polarity. + + + · Remove the batteries when they are not used for a long time. · Do not use the rechargeable batteries (Ni-Cd type). · Be sure to use alkaline batteries. 19 ENGLISH than this receiver. For detalis, refer to "Entering a setup code" on page 20. R-772(A)2007.8.165:21PM 20 USING FUNCTIONS OF REMOTE CONTROL · This remote control can control up to 8 different components. · Before operating audio and video components other than this receiver with using this remote control, the setup code for each component should be entered. · For system remote control operation, "000" was stored previously in the memory of the device button "CD" for Sherwood CD player, "DVD" for Sherwood DVD player, "AUX" for Sherwood tape deck and "TV" for Sherwood TV respectively as its factory setup code. So, you don't need to enter its code for each Sherwood component except in such a case that its code does not work. Note : · If the transmission signal which this remote control emits is changed into "RF"(Radio Frequency), this remote contol cannot control other audio and video components. (For details, refer to "Changing the transmission signal" on page 28.) ENGLISH Entering a setup code · Setup code entry is the easiest way to program this remote control for operating audio and video components. 4. While "LEARN" is displayed, press the CURSOR UP()/DOWN() buttons to select the setup code mode ("CODE"), then press the ENTER button. 1. Turn on the component you want to operate. 2. Find the setup codes according to the type and the brand name of your component, referring to "Setup Code Table" on page 73. · Each time the CURSOR UP()/DOWN() buttons are pressed, the mode changes as follows : LEARN RF-IR DELETE MACRO CODE PUNCH · Then "PRESET" and 3 digit number are displayed. · If "PRESET", etc. go off, start again from the above step 3. 3. Press and hold down both the ENTER button and the desired one of the DEVICE buttons for more than 2 seconds. 5. While "PRESET", etc. are displayed, enter a 3 digit code and press the ENTER button, aiming the remote sensor on the component. Example: When entering "001". · Then "LEARN" is displayed on the LCD screen for several seconds. Notes : · The AUDIO button is unavailable for the audio components other than this receiver. · During setting operation, to exit from the setting mode, press any of the DEVICE buttons. · Then "OK" is displayed on the LCD screen. · To be sure that the setup code is correct, press the POWER ON (or STANDBY) button. · If the setup code is correct, your component will be turned off. · When your component is not turned off, repeat the above steps 2 to 5, trying entering each code for your component until you find one that works. · If "NG" is displayed, retry entering the correct setup code while "PRESET" and 3 digit number are displayed. 20 R-772(A)2007.8.165:21PM 21 6. Operate the component using the corresponding function buttons. · If any of buttons fails to operate as they should, start from the step 1 again to enter the correct setup code. Note : · Manufacturers may use different setup codes for the same product category. For that reason, it is important that you check to see if the code you have entered operates as many controls as possible. If only a few functions operate, check to see if another code will work with more buttons. 3. While "PRESET" is displayed, search a setup code, aiming the remote control at the remote sensor on the component. 7. Repeat the above steps 1 to 6 for each of your other components. · Each time the CURSOR UP()/DOWN() buttons are pressed, the setup code is selected one by one. · If the selected code is correct, your component will be turned off. · When your component is not turned off, repeat this step until you find one that works. Searching a setup code · In addition to enter a setup code using "Setup Code Table" on page 73, it is also possible to search through all the codes that are stored in the library of this remote control. 4. While "PRESET" is displayed, press the ENTER button to store the setup code. 1. Turn on the component you want to operate. 2. Perform the steps 3 and 4 in "Entering a setup code" procedure on page 20 to select the setup code mode ("CODE"). · Then "OK" is displayed on the LCD screen. 5. Operate the component using the corresponding function buttons. · If any of buttons fails to operate as they should, start from the step 1 again to find the correct setup code. 6. Repeat the above steps 1 to 5 for each of your other components. 21 ENGLISH R-772(A)2007.8.165:21PM 22 Programing the commands from other remote controls (LEARNING mode) · If the setup codes are not available for your component or you want to program a missing or special function into one button of a device, the learning function enables this remote control to learn the commands from other remote controls. 4. While "SEL" is flickering, on this remote control, press the button corresponding to the function to be learned. Example: If the function to be learned is playback, press the PLAY() button. ENGLISH 1. Place this remote control and other remote control facing each other at a distance of 5 to 15 cm (2 to 6 inches ) apart. 2. Press and hold down the ENTER button and the desired one of the DEVICE buttons for more than 2 seconds. · Then "READY" is displayed. Note: · You cannot program a function into some buttons such as DEVICE, MACRO and LIGHT buttons. 5. While "READY" is displayed, on the other remote control, press the button of the function to be learned. · If the command has been learned successfully, "OK" is displayed and then "SEL" is flickering. · If "ERROR" is displayed and then "SEL" is flickering, it means that for some reason the command was not learned. In this case, repeat the above steps 4 and 5. Notes : · If an incorrect signal has been sent or, in some cases, the command from other remote control simply cannot be learned. · In some "ERROR" cases, the remote controls just need to be moved closer together or farther apart. · Then "LEARN" is displayed on the LCD screen for several seconds Note : · During setting operation, to exit from the setting mode, press any of the DIVICE buttons. 3. While "LEARN" is displayed, press the ENTER button. 6. While "SEL" is flickering, repeat the above steps 4 and 5 to program all the commands you want to the buttons on this remote control under the same device mode. To exit from the setting mode, press any of the DEVICE buttons. 7. Repeat the above steps 1 to 6 to program the commands from a different remote control. · Then "SEL" is flickering. · If "SEL" goes off, start again from the above step 2. 8. Operate the newly programmed buttons to make sure the learning function was performed properly. 22 R-772(A)2007.8.165:21PM 23 Erasing the programmed command from one button Erasing all the commands programmed under a device mode code" procedure on page 20 to select the delecting mode ("DELETE"). · Then "BTTN" is displayed on the LCD screen for several seconds. code" procedure on page 20 to select the deleting mode ("DELETE"). · Then "BTTN" is displayed on the LCD screen for several seconds. 2. While "BTTN" is displayed, press the CURSOR UP()/DOWN() buttons to select the one command deleting mode (BTTN), then press the ENTER button. 2. While "BTTN" is displayed, press the CURSOR UP()/DOWN() buttons to select the all command deleting mode ("LEARN"), then press the ENTER button. · Each time the CURSOR UP()/DOWN() buttons are pressed, "BTTN" or "LEARN"(all command deleting mode) is selected. · Then "SEL" is flickering. · If "SEL" goes off, start again from the above step 1. · Then "SURE?" is displayed . · If "SURE?" goes off, start again from the above step 1. 3. While "SURE?" is displayed, press the ENTER button. 3. While "SEL" is flickering, press the button for the command you want to erase. Example: When the button for the command to be erased is PLAY button. · Then all the commands programmed are erased. 4. To erase all the commands programmed under · "OK" is displayed and then "SEL" is flickering. other device mode, repeat the above steps 1 to 3. 4. While "SEL" is flickering, repeat the above step 3 to erase other commands. 23 ENGLISH 1. Perform the steps 3 and 4 in "Entering a setup 1. Perform the steps 3 and 4 in "Entering a setup R-772(A)2007.8.165:21PM 24 Programming a macro function · The macro function enables you to program a series of button operations(up to 15) on this remote control into a single button. · You can store up to three separate macro command sequences into "M1", "M2" and "M3" buttons. 3. While "SEL" is flickering, press the operation buttons you want to program in order. Example: When playing a DVD on the DVD player connected to VIDEO 2 jacks of this receiver. . Press "AUDIO" button to control this receiver. . Press "POWER ON" button to turn this receiver on. . Press "VIDEO 2(7)" button to select the desired input source. . Press "DVD" button to control the DVD player. . Press "POWER ON" button to turn the DVD player on. . Press "PLAY ()" button to start playback. ENGLISH 1. Perform the steps 3 and 4 in "Entering a setup code" procedure on page 20 to select the macro mode ("MACRO"). · Then "M1" is displayed on the LCD screen for several seconds. · During macro setting operation, pressing any of the DEVICE buttons cannot exit from the macro mode. 2. While "M1" is displayed, press the CURSOR UP()/DOWN() buttons to select the MACRO button to be programmed into, then press the ENTER button. · Each time the operation buttons are pressed, the programmed order is displayed. 4. Press any of the MACRO buttons (M1~M3) to complete the programming. · Each time the CURSOR UP()/DOWN() buttons are pressed, "M1", "M2" or "M3" is selected. · Then "SEL" is flickering. · If "SEL" goes off, start again from the above step 1. · Then "OK" is displayed. To erase a macro program · When erasing a macro program, perform the above steps 1, 2 and 4, but ignore the step 3. To change a macro program · When a new macro program is stored into a MACRO button with performing the above steps 1 to 4, the previous macro program is erased from the memory of the MACRO button. 24 R-772(A)2007.8.165:21PM 25 Operating a macro function · Aim the remote control at the REMOTE SENSORs of the components to be controlled and press the MACRO button you want. Example : When pressing "M1" button. 2. While "VOL" is displayed, press the CURSOR ENGLISH UP()/DOWN() buttons to select the desired punch-through mode, then press the ENTER button. Notes: · The codes programmed into a MACRO button will be transmitted at an interval of 0.5 seconds. However, some components may not be able to complete one operation in 0.5 seconds and may miss the next code. In this case, the macro function cannot control the corresponding components correctly. · Be sure to use the remote control within the remote control operation range of the components. · Depending on the operation status of the components, etc., the macro function cannot control the corresponding components correctly. · Each time the CURSOR UP()/DOWN() buttons are pressed, the mode changes as follows: VOL : The volume punch -through mode allows the "VOLUME /" and "MUTE" buttons to operate a different device. DELETE : All punch-through deleting mode. PLAY : The transport punch-through mode ", ", ", allows the " "", " " "", " " , "/" and "" buttons to operate a different device. CH : The channel punch-through mode allows the "CHANNEL /" and "CH. Programing a punch-through function · The punch-through function allows the volume controls, channel controls or transport controls to link to a different device while a device is controlled with this remote control as a master device. · For example, since this receiver will likely be used as the sound system while watching TV, you may want to use volume controls to operate this receiver although this remote control is set to control the TV. LEVEL" buttons to operate a different device. · Then the device to which you can link the selected punch-through mode is displayed. 1. Perform the steps 3 and 4 in "Entering a setup code" procedure on page 20 to select a master device and the punch-through mode ("PUNCH"). · Then "VOL" is displayed on the LCD screen for several seconds. 25 R-772(A)2007.8.165:21PM 26 Continued 3. While the device is displayed, press the ENGLISH CURSOR UP()/DOWN() buttons to select the desired punch-through device, then press the ENTER button. Operating a punch-through function · While this remote control is set to control a master device, aim the remote control at the REMOTE SENSOR of the punch-through device and press the desired button of the programmed punch-through controls. Example: When pressing "PLAY ()" button. · Each time the CURSOR UP()/DOWN() buttons are pressed, depending on the selected punch-through mode, punch-through devices and the one punch-through deleting mode ("DELETE") are selected as follows : · In case of the volume punch-through, AUDIO DELETE TV · In case of the transport punch-through, CD DELETE DVD VCR AUX · In case of the channel punch-through, TV DELETE SAT CABLE VCR · Then "OK" is displayed and the current punchthrough mode is displayed. · Then the punch-through device is displayed on the LCD screen. Erasing the programmed puch-through function 1. Perform the steps 3 and 4 in "Entering a setup code" procedure on page 20 to select a master device and the punch-through mode ("PUNCH"). · Then "VOL" is displayed on the LCD screen for several seconds. 4. While the punch-through mode is displayed, repeat the above steps 2 and 3 to program other punch-through function under the same master device mode. 2. While "VOL" is displayed, press the CURSOR UP()/DOWN() buttons to select the punchthrough mode to be erased, then press the ENTER button. 5. To program punch-through functions under other master device mode, repeat the above steps 1 to 4. · Each time the CURSOR UP()/DOWN() buttons are pressed, the mode changes as follows: VOL DELETE PLAY CH · Then the device is displayed . 26 R-772(A)2007.8.165:21PM 27 Continued 3. While the device is displayed, press the CURSOR UP()/DOWN() buttons to select the one punch-through deleting mode ("DELETE"), then press the ENTER button. Erasing all the punch-through functions programmed under a master device mode code" procedure on page 20 to select a master device and the punch-through mode ("PUNCH"). · Then "VOL" is displayed on the LCD screen for several seconds. 2. While "VOL" is displayed, press the CURSOR UP()/DOWN() buttons to select the all punch-through deleting mode ("DELETE"). · Each time the CURSOR UP()/DOWN() buttons are pressed, depending on the selected punch-through mode, the punchthrough devices and the deleting mode ("DELETE") are selected. · Then "OK" is displayed and the current punchthrough mode is displayed . 4. While the punch-through mode is displayed, repeat the above steps 2 and 3 to erase other punch-through function under the same master device mode. · Each time the CURSOR UP()/DOWN() buttons are pressed, the mode changes as follows: VOL DELETE PLAY CH · Then "DELETE" is displayed . 5. To erase punch-through functions under other master device mode, repeat the above steps 1 to 4. 3. While "DELETE" is displayed, to erase all the punch-through functions programmed under the master device mode, press ENTER button. · Then "OK" is displayed and "DELETE" is displayed. · To exit from the deleting mode, press any of the DEVICE buttons. 4. To erase all the punch-through functions programmed under other master device mode, repeat the above steps 1 to 3. 27 ENGLISH 1. Perform the steps 3 and 4 in "Entering a setup R-772(A)2007.8.165:21PM 28 Changing the transmission signal · This remote control can emit not only the infrared beams which the conventional remote control uses but also the RF(Radio Frequency) beams which are stronger than those. · When you want to control this receiver from longer distance even if there are obstacles such as walls, furniture, etc. in the way, change the transmission signal into "RF"(Radio Frequency). Notes: · When the RF remote antenna is not connected, remote operation will become unreliable. (For details, refer to "CONNECTING RF REMOTE ANTENNA" on page 12.) · If the transmission signal mode is set to "RF" (Radio Frequency), this remote control cannot control other audio and video components. 3. While "RF" (or "IR") is displayed, press the CURSOR UP()/DOWN() buttons to select the desired transmission signal, then press the ENTER button. ENGLISH 1. Press and hold down the ENTER button and any of the DEVICE buttons for more than 2 seconds. · Each time the CURSOR UP()/DOWN() buttons are pressed, the mode changes as follows : "RF" : This remote control emits the RF(Radio Frequency) beams which stronger than the infrared beams. "IR" : This remote control emits the infrared beams which the conventional remote control uses. · Then "OK" is displayed. When "RF" is set to. 4. To pair up this remote control and the receiver, press the CONTROL DOWN() button and the MEMORY/ENTER button simultaneously on the receiver. · Then "LEARN" is displayed on the LCD screen for several seconds. Note: · During setting operation, to exit from the setting mode, press any of the DEVICE buttons. 2. While "LEARN" is displayed, press the CURSOR UP()/DOWN() buttons to select the transmission signal mode("RF-IR"), then press the ENTER button. · "RF REMOCON PAIRING MODE" is displayed for several seconds on the display of the receiver. · If "RF REMOCON PAIRING MODE" goes off, press these buttons again. 5. While "RF REMOCON PAIRING MODE" is displayed, press the ENTER button, aiming at the receiver. · Then "RF" (or "IR") is displayed. · If "RF" (or "IR") goes off, start again from the above step 1. · Then "PAIRING SUCCESS" is displayed. 28 R-772(A)2007.8.165:21PM 29 ROOM 2 Remote Controls ENGLISH This remote control unit is an additional remote control unit for the ROOM 2 source playback only. · You can use the ROOM 2 functions with this remote control unit more conveniently in another room than with the universal remote control unit. · For details on ROOM 2 operation, refer to "ROOM 2 SOURCE PLAYBACK" on page 44. REMOTE CONTROL OPERATION RANGE · Aim the ROOM 2 remote control at the IR receiver installed in another room.(For details, refer to "CONNECTING MULTI-ROOM SYSTEM KIT" on page 13.) · When you operate the ROOM 2 function in the main room, aim the ROOM 2 remote control at the remote sensor of this receiver. LOADING BATTERY 1. Remove the cover. 2. Load the battery(CR2025) matching the polarity. · Remove the battery when it is not used for a long time. 29 R-772(A)2007.8.165:21PM 30 Operations Notes: ENGLISH · Before operating this receiver with the supplied remote control, refer to "Universal Remote Controls" on page 17 for details about operation. · Before operating this receiver, first set this unit as desired for optimum performance, doing the OSD menu setting procedures. (For details, refer to "OSD Menu Settings" on page 47.) LISTENING TO A PROGRAM SOURCE Before operation · Enter the standby mode. · The POWER ON/STANDBY button lights up amber. This means that the receiver is not disconnected from the AC mains and a small amount of current is retained to support the operation readiness. · To switch the power off, push the POWER switch again. Then the power is cut off and the POWER ON/STANDBY button goes off. 3. Select the desired input source. 1. In the standby mode, turn the power on. · Each time the "AUDIO" button on the front panel is pressed, the input source changes as follows: CD AUX TAPE · Each time the "VIDEO" button on the front panel is pressed, the input source changes as follows: VIDEO 1VIDEO 2VIDEO 3 VIDEO 4 · Each time the "TUNER" button is pressed, the band changes as follows: FM STereo FM MONO AM XM · Each time the POWER ON/STANDBY button on the front panel is pressed, the receiver is turned on to enter the operating mode (the POWER ON/ STANDBY button lights up blue) or off to enter the standby mode(the POWER ON/STANDBY button lights up amber). · On the remote control, press the POWER ON button to enter the operating mode or press the STANDBY button to enter the standby mode. · In the standby mode, if the INPUT SELECTOR button is pressed, the receiver is turned on automatically and the desired input is selected. When selecting the EXTERNAL IN as desired, 2. Switch the speakers on. · Then the SPEAKER indicator lights up and the sound can be heard from the speakers connected to the speaker terminals. · When using the headphones for private listening, press the SPEAKER button again to switch the speakers off. · Depending on the power amplifier setting for the surround back channels and the surround back speaker setting, "EXT. IN" is displayed and 8(/7/6) separate analog signals from the component connected to this input pass through the tone and volume circuits only and can be heard from your speakers. · Select the desired input source to cancel the external in function. · These analog signals can be heard only, not recorded. 30 R-772(A)2007.8.2010:2AM 31 When CD, AUX, VIDEO 1~ 4 is selected as an input source · If the AUDIO MODE is set to the mode other than "DIGITAL" for the corresponding input source on the INPUT SETUP menu, you cannot hear the sound from the selected digital input. (For details, refer to "SETTING THE INPUT SETUP" on page 53.) 6. Operate the selected component for playback. · When playing back the program sources with surround sound, refer to "ENJOYING SURROUND SOUND" on page 34. 7. Adjust the (overall) volume. 4. Press the AUDIO ASSIGN button. Muting the sound · "AUD ~ " is displayed for several seconds. · "AUD ~ " disappears, press the AUDIO ASSIGN button again. 5. Select the desired of the digital inputs connected while displaying "AUD ~ ". · "MUTE" flickers. · To resume the previous sound level, press it again. Listening with headphones · Each time the MULTI CONTOL knob is rotated or the CURSOR LEFT()/RIGHT() buttons are pressed, the corresponding input is selected as follows : Notes: · When the selected digital input is not connected or assigned, "o1", "c1", etc (, meaning no digital signal input from it) or "d"(, meaning no audio assignment) flickers and no sound will be heard. · The selected digital input is automatically assigned to the corresponding input source on the INPUT SETUP menu. (For details, refer to "SETTING THE INPUT SETUP" on page 53.) · The sound from the component connected to the selected digital input can be heard regardless of the selected input source. · Ensure that the SPEAKER button is set to off. · Depending on the signal format which is being input, you can listen in Dolby Headphone mode, stereo mode, etc. (For details, refer to "Listening in Dolby Headphone mode" on page 35). · When the EXTERNAL IN is selected as an input source, only front left and front right channel signals can be reproduced through the headphones. Note: · Be careful not to set the volume too high when using headphones. 31 ENGLISH R-772(A)2007.8.165:21PM 32 SURROUND SOUND · This receiver incorporates a sophisticated Digital Signal Processor that allows you to create optimum sound quality and sound atmosphere in your personal Home Theater. ENGLISH Surround modes DTS Digital Surround DTS Digital Surround(also called simply DTS) is a multi-channel digital signal format which can handle higher data rates. Discs bearing the " " include the recording of up to 5.1 channels of digital signals, which can be generally thought to provide better sound quality due to the lower audio compression required. It also provides wide dynamic range and separation, resulting in magnificent sound. · DTS Neo : 6 Cinema This mode is optimum for playing movies. Decoding is performed with emphasis on separation performance to achieve the same atmosphere with 2-channel sources as with 6.1-channel sources. · DTS Neo : 6 Music This mode is suited mainly for playing music. The front left and front right signals bypass the decoder and are played directly so there is no loss of sound quality, and the effect of the surround signals from the center, surround left, surround right and surround back channels adds a natural sense of expansion to the sound field. DTS - ES Extended SurroundTM ( ) This is a new multi channel digital signal format which greatly improves the 360- degree surround impression and space expression thanks to further expanded surround signals, offering high compatibility with the conventional DTS format. In addition to the 5.1 channels, DTS-ES Extended Surround also offers the surround back (sometimes also referred to as "surround center") channel for surround playback with a total of 6.1 channels. DTS-ES Extended Surround includes two signal formats with different surround signal recording methods as follows: · DTS-ESTM Discrete 6.1 Because the signals for 6.1 channels (including the surround back channel) are fully independent, it is possible to achieve a sense that the acoustic image are moving about freely among the background sounds surrounding the listener from 360 degrees. Though maximum performance is achieved when sound tracks recorded with this system are played using a DTS -ES decoder, when played with a conventional DTS decoder, the surround back channel signals are automatically downmixed to the surround left and surround right channels so that none of the signal components are lost. · DTS - ESTM Matrix 6.1 With this format, the additional surround back channel signals undergo matrix encoding and are input to the surround left and surround right channels beforehand. During playback, they are decoded to the surround left, surround right and surround back channels. Because the bit stream format is 100% compatible with conventional DTS signals, the effect of the DTS-ES Matrix 6.1 format can be achieved even with DTS 5.1- channel signal sources. Of course, it is possible to play DTS-ES Matrix 6.1 channel signal sources with a DTS 5.1 - channel decoder. When DTS-ES Discrete 6.1 or Matrix 6.1 sources are decoded with a DTS - ES decoder, the format is automatically detected upon decoding and the optimum surround mode is selected. However, some DTS - ES Matrix 6.1 sources may be detected as DTS sources. In this case, the DTS - ES Matrix mode should be selected manually to play these sources. DTS 96/24 Conventional surround formats used sampling frequencies of 48 or 44.1 kHz, so 20 kHz was about the maximum playback signal frequency. With DTS 96/24, the sampling frequency is increased to 96 or 88.2 kHz to achieve a wide frequency range of over 40 kHz. In addition, this format has a resolution of 24 bits, resulting in the same frequency band and dynamic range as 96kHz / 24 bit PCM signals. As with conventional DTS surround, DTS 96/24 is compatible with a maximum of 5.1 channels. DTS 96/24 is fully compatible with the conventional DTS surround format, so DTS 96/24 sources can be played using a conventional DTS 5.1 channel decoder. "DTS" and "DTS-ES I Neo:6" are registered trademarks of DTS, Inc. "96/24" is a trademarks of DTS, Inc. Dolby Digital Dolby Digital is the multi- channel digital signal format developed by Dolby Laboratories. Discs bearing the " " includes the recording of up to 5.1 channels of digital signals, which can reproduce much better sound quality, spatial expansion and dynamic range characteristics than the previous Dolby Surround effect. Dolby Digital EX This mode creates the back (sometimes also referred to as "surround center") signals from the surround left and right signals in Dolby Digital 5.1 channel source using a matrix decoder and provides 6.1 channel surround playback. For the best results, this mode should be selected during playback of sources(bearing the " ") recorded in Dolby Digital EX. With this additional channel, you can experience more dynamic and realistic moving sound especially. When Dolby Digital EX sources are decoded with a Dolby Digital EX decoder, the format is automatically detected upon decoding and the Dolby Digital EX mode is selected. However, some Dolby Digital EX sources may be detected as Dolby Digital sources. In this case, the Dolby Digital EX mode should be selected manually to play these sources. DTS Neo : 6TM surround This mode applies conventional 2-channel signals such as digital PCM or analog stereo signals to the high precision digital matrix decoder used for DTS-ES Matrix 6.1 to achieve 6.1channel surround playback. DTS Neo : 6 surround includes two modes for selecting the optimum decoding for the signal source. 32 R-772(A)2007.8.165:21PM 33 Dolby Pro Logic IIx surround Dolby Pro Logic IIx decodes all stereo (2 channel ) and 5.1 channel sources and extends to 7.1channel surround playback. It delivers the most natural, full range and immersing 7.1 channel listening experience. Dolby Pro Logic IIx surround includes three modes as follows : · Dolby Pro Logic IIx Movie When enjoying movies, this mode allows you to further enhance the cinematic quality by adding processing that emphasizes the sounds of the action special effects. · Dolby Pro Logic IIx Music When listening to music, this mode allows you to further enhance the sound quality by adding processing that emphasizes the musical effects. · Dolby Pro Logic IIx Game When playing games, this mode allows you to further enhance the dynamic surround effects by adding processing that emphasizes the surrounded and exciting sound. Dolby Pro Logic II surround This mode applies conventional 2-channel signals such as digital PCM or analog stereo signals as well as Dolby Surround signals, etc. to surround processing to offer improvements over conventional Dolby Pro Logic circuits. Dolby Pro Logic II surround includes Dolby Pro Logic II Movie, Dolby Pro Logic II Music and Dolby Pro Logic II Game like Dolby Pro Logic IIx surround. Dolby Virtual Speaker This mode creates a virtual surround sound field using as few as two front speakers, allowing you to experience listening from 5.1 channel speakers. This mode is effective not only for 5.1 channel sources but also for stereo(2 channel) sources. Dolby VIrtual Speaker includes two listening mode as follows: · Dolby Virtual Speaker Reference The width of the front sound image is defined by the actual distance between front speakers. · Dolby Virtual Speaker Wide The width of the front sound image seems to extend beyond the front speakers. Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" and the double-D symbol are trademarks of Dolby Laboratories. · The following modes apply conventional 2-channel signals such as digital PCM or analog stereo signals to high performance Digital Signal Processor to recreate sound fields artificially. Select one of the 7 provided surround modes according to the program source you want to play. Theater This mode provides the effect of being in a movie theater when watching a play. Hall This mode provides the ambience of a concert hall for classical music sources such as orchestral, chamber music or an instrumental solo. Stadium This mode provides the expansive sound field to achieve the true stadium effect when watching baseball or soccer games. Room This mode provides the sound field of a house with a low ceiling and hard walls for jazz music. Panorama This mode provides a dynamic and broad sound space to highten the overall impact of the sound track. Classic This mode provides the acoustic effects of a large concert hall for classical music. Multi CH Stereo This mode is designed for playing background music. The front, surround and surround back channels create a stereo image that encompasses the entire area. · When using the EXTERNAL INs to play back the sound from the additional multi-channel decoder for surround sound, you can enjoy the corresponding surround sound, too.( For details, refer to the operating instructions of the component to be connected.) For your reference, the sound from each channel can be reproduced according to the surround modes as follows: Modes DTS, DTS 96/24 DTS ES DISCRETE/MATRIX DTS NEO: 6 CINEMA/MUSIC DOLBY DIGITAL DOLBY DIGITAL EX DOLBY PRO LOGIC IIx MOVIE/MUSIC/GAME DOLBY PRO LOGIC II MOVIE/MUSIC/GAME DOLBY VIRTUAL SPEAKER MULTI PCM Other Surrounds STEREO EXTERNAL IN Channels FRONT L/R CENTER -- SURROUND L/R -- SURROUND BACK L/R -- -- -- -- /-- -- SUBWOOFER --(*) --(*) --(*) --(*) (*): Depending on the subwoofer setting, the sound from the subwoofer channel may be reproduced. · Depending on the speaker settings and the number of the encoded channels, etc., the sound from the corresponding channels cannot be reproduced.(For details, refer to "SETTING THE SPEAKER / ROOM EQ SETUP" on page 57.) 33 ENGLISH Dolby Headphone The Dolby Headphone function simulates 5.1 channel surround sound , which allows you to enjoy 5.1 channel surround sound through 2 channel headphones, just like listening from 5.1 channel speakers. This mode is effective not only for 5.1 channel sources but also for stereo ( 2 channel ) sources. R-772(A)2007.8.165:21PM 34 ENJOYING SURROUND SOUND Notes: · Before surround playback, first perform the speaker setup procedure, etc. on the OSD menu for optimum performance. (For details, refer to "SETTING THE SPEAKER/ROOM EQ SETUP" on page 57.) · When playing digital signals from the Dolby Digital program source or selecting the surround mode such as Dolby Pro Logic II /Dolby Pro Logic IIx Music, Dolby Headphone, Dolby Virtual Speaker modes, you can adjust their parameters for optimum surround effect. (For details, refer to "SETTING THE SOUND PARAMETER" on page 66.) · When the EXTERNAL IN is selected as an input source, the surround modes cannot be selected. ENGLISH Depending on how to select a surround mode, select the auto surround mode or the manual surround mode. · Each time this button is pressed, the mode changes as follows : Auto surround mode : The optimum surround mode will be ("AUTO" lights up.) automatically selected depending on the signal format being input. Manual surround mode : You can select the desired of different ("AUTO" goes off.) surround modes selectable for the signal being input with using the MULTI CONTROL knob or the SURROUND MODE UP/DOWN ( / ) buttons. Notes : · Even when the auto surround mode is selected and the same type of digital signal format is being input, the optimum surround mode may vary depending on whether the speaker type is set to "NO" or not. · When the auto surround mode is selected, the surround modes other than the optimum surround mode cannot be selected. When selecting the manual surround mode with pressing the SURROUND MODE button on the front panel. Select the desired surround mode. · Each time the MULTI CONTROL knob is rotated or the SURROUND MODE UP / DOWN ( >/< ) buttons are pressed, the surround mode changes depending on the input signal format as follows : Signal format being input Dolby Digital EX 6.1 channel sources, Dolby Digital 5.1 channel sources Dolby Digital 2 channel sources DTS ES Discrete/Matrix 6.1 channel sources DTS sources, DTS 96/24 sources PCM (multi-channel) sources* 96 kHz PCM (2 channel) sources PCM (2 channel) sources, Analog stereo sources Selectable surround mode , (DOLBY D + PLIIx MOVIE), DOLBY DIGITAL, DOLBY VS REF, DOLBY VS WIDE , [DOLBY PLII MOVIE, DOLBY PLII MUSIC, DOLBY PLII GAME], DOLBY VS REF, DOLBY VS WIDE , (DTS + PLIIx MOVIE), DTS, DOLBY VS REF, DOLBY VS WIDE correnponding DTS mode, DOLBY VS REF, DOLBY VS WIDE, , (DTS + PLIIx MOVIE) MULTI PCM, , DOLBY VS REF, DOLBY VS WIDE , [DOLBY PLII MOVIE, DOLBY PLII MUSIC, DOLBY PLII GAME], DOLBY VS REF, DOLBY VS WIDE, NEO:6 CINEMA, NEO:6 MUSIC, THEATER, HALL, STADIUM, ROOM, PANORAMA, CLASSIC, MULTI CH STEREO · Depending on surround back speaker setting, some surround modes can be selected or not as follows: < >: Possible only when surround back speaker is not set to "NO". [ ] : Possible only when surround back speaker is set to "NO". ( ): Possible only when surround back speaker is set to " 2CH". * : Depending on the signal format being input, the Dolby Pro Logic IIx modes and the Dolby Virtual Speaker modes may not be selected. 34 R-772(A)2007.8.165:21PM 35 Continued To cancel the surround mode for stereo operation · Depending on the signal format which is being input, either the stereo mode or the 2CH downmix mode is selected. · To cancel either the stereo mode or the 2CH downmix mode, select the surround mode with using the MULTI CONTROL knob on the front panel or the SURROUND MODE UP/DOWN ( >/< ) buttons on the remote control. 2CH downmix mode · This mode allows the multi-channel signals encoded in DTS or Dolby Digital format, etc. to be mixed down into 2 front channels and to be reproduced through only two front speakers or through headphones. · When the SPEAKER button is set to off to listen with headphones, if the STEREO button is pressed while playing the multi-channel digital signals from DTS or Dolby Digital sources, etc., it will enter the 2CH downmix mode automatically. · To cancel the 2CH downmix mode, select the Dolby Headphone mode with using the MULTI CONTROL knob on the front panel or the SURROUND MODE UP/DOWN ( >/< ) buttons on the remote control. Listening in Dolby Headphone mode · The Dolby Headphone function simulates 5.1 channel surround sound, which allows you to enjoy 5.1 channel surround sound through 2 channel headphones, just like listening from 5.1 channel speakers. Note : · Only when the SPEAKER button is set to off, the Dolby Headphone mode can be selected. · Switch the speakers off to listen with headphones. · Then "DOLBY HEADPHONE" (or "DOLBY H ~ ") is displayed and the Dolby Headphone mode is selected. · To cancel the Dolby Headphone mode, press the SPEAKER button again. Adjusting each channel level with test tone · The volume level of each channel can be adjusted easily with the test tone function. Note : When the SPEAKER button is set to off, the test tone function does not work. 2. At each channel, adjust the level as desired until the sound level of each speaker is heard to be equally loud.