User manual SHERWOOD RD-7106

OPERATINGINSTRUCTIONS TDAS TOTALLY DISCRETE AMPLIFIER STAGE MASTER VOLUME ST TUNED TAPE M PRESET MEM MAIN POWER REMOTE SENSOR dB kHz MHz DTS DIGITAL Pro Logic LOCK ms SLEEP ON/ OFF STANDBY INPUT SELECTOR AUDIO VIDEO TAPE MON. 6CH DIRECT AUTO SURROUND MODE DSP MODE STEREO DIGITAL INPUTS CHECK ON/STANDBY PHONES SPEAKER CHANNEL SELECTOR ADJUST TONE MODE SPEAKER MODE DYNAMIC RANGE VIDEO 4 CINEMA EQ MEMO/ENTER TUNING/PRESET T/P MODE FM MODE BAND ON/OFF S-VIDEO VIDEO L - AUDIO - R RD-7106 AUDIO/VIDEO RECEIVER Introduction UNPACKING AND INSTALLATION ENGLISH Your new high fidelity receiver is designed to deliver maximum enjoyment and years of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help ensure a trouble free installation. Please unpack your unit carefully. We recommend that you save the carton and packing material. They will be helpful if you ever need to move your unit and may be required if you ever need to return it for service. Your unit is designed to be placed in a horizontal position and it is important to allow at least two inches of space behind your unit for adequate ventilation and cabling convenience. To avoid damage, never place the unit near radiators, in front of heating vents, in direct sunlight, or in excessively humid or dusty locations. Connect your complementary components as illustrated in the following section. FOR U.S.A. Note to CATV System Installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING CAUTION : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Caution regarding placement (Except for U.S.A. and Canada) To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below. Left and right panels: 5 cm Rear panel: 10 cm Top panel: 20 cm To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Caution : Do not block ventilation openings or stack other equipment on the top. 2 READ THIS BEFORE OPERATING YOUR UNIT FOR U.S.A. AND CANADA ................................. 120 V FOR OTHER COUNTRIES ........................ 115 V/230 V FOR YOUR SAFETY Units shipped to the U.S.A. and Canada are designed for operation on 120 volts AC only. Observe all, safety precaution for use of a polarized AC plug. However, some products may be supplied with a non polarized plug. FOR YOUR SAFETY Units shipped to countries other than the above countries are equipped with an AC voltage selector switch on the rear panel. Refer to the following paragraph for the proper setting of this switch. AC VOLTAGE SELECTION This unit operates on 115/230 V AC. The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction. AC voltage selector switch CAUTION : To prevent electric shock, match wide blade of plug to wide slot, insert fully. FOR EUROPE AND AUSTRALIA ......... 230 V/240 V FOR YOUR SAFETY Units shipped to Australia are designed for operation on 240 V AC only. To ensure safe operation, the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Improper extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician. PAN-EUROPEAN UNIFIED VOLTAGE All units are suitable for use on supplies 230-240 V AC. AC 230 V AC 115 V Move switch lever to match your line voltage with a small screwdriver or other pointed tool. 3 ENGLISH CONTENTS ENGLISH Introduction UNPACKING AND INSTALLATION ....................................................................................................... 2 READ THIS BEFORE OPERATING YOUR UNIT................................................................................... 3 System Connections........................................................................................................................................ 5 Front Panel Controls ...................................................................................................................................... 8 DIGI LINK III System Remote Controls.................................................................................................. 9 REMOTE CONTROL OPERATION RANGE.......................................................................................... 10 LOADING BATTERIES............................................................................................................................ 10 Operations LISTENING TO A PROGRAM SOURCE................................................................................................ 11 SURROUND SOUND................................................................................................................................ 14 ENJOYING SURROUND SOUND........................................................................................................... 16 LISTENING TO RADIO BROADCASTS ................................................................................................ 20 RECORDING ............................................................................................................................................ 22 OTHER FUNCTIONS................................................................................................................................ 24 Using the OSD CURRENT STATUS DISPLAY................................................................................................................ 25 MENU SCREEN ........................................................................................................................................ 25 Troubleshooting Guide ................................................................................................................................ 27 Specifications.................................................................................................................................................. 28 4 System Connections When making system connections, please be certain the AC cord is not plugged into an AC outlet. When making system connections, please be sure to connect the white RCA pin cords to the L(left) and the red RCA pin cords to the R(right) jacks. Change the position of the FM indoor antenna until you get the best reception of your favorite FM stations. A 75 outdoor FM antenna may be used to further improve the reception. Disconnect the indoor antenna before replacing it with the outdoor one. Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC input cord and set it to a direction for the best reception. If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of the AM loop antenna. Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver. If the electricity fails or the AC input cord is left unplugged for about 2 weeks, the memorized contents will be cleared. Should this happen, you must enter them, again. s CONNECTING AUDIO COMPONENTS CD player MULTIPLE COMPACT DISC PLAYER CDC-5080R OPEN/CLOSE s CONNECTING VIDEO COMPONENTS S-VIDEO OUT VIDEO OUT IN CD V-CD PBC REVERT PROG PEAK DELETE AUTO EDIT A B POWER ON/OFF GRAPHICS SCENE TRACK RANDOM REPEAT ALL 1 DISC S A< >B MPX INTRO INDEX STEP 1 2 3 4 5 1 23 4 56 7 89 10 11 12 13 14 15 PHONES LEVEL REMOTE SENSOR PROGRAM/REVIEW RANDOM REPEAT MIN MAX PHONES AUDIO PLAY(OUT) AUDIO REC(IN) Video deck 1 POWER ON/OFF MULTIPLE COMPACT DISC PLAYER CDC-5080R V-CD PBC REVERT PEAK PROG AUTO EDIT A B RANDOM SCENE TRACK INDEX GRAPHICS DELETE REPEA T ALL 1 DISC S A< >B MPX INTRO STEP OPEN/CLOSE 1 2 3 4 5 1 4 7 10 13 2 3 5 6 8 9 11 12 14 15 PLAY(LINE OUT) Tape deck or additional audio component AUX DIGI-LINK STEREO DOUBLE CASSETTE DECK DD-5080C RESET BC HIGH NORM CD SYN REC L PHONES LEVEL PHONES MIN MAX COUNTER A/B MODE M MIN SEC RELAY P MPX T SIZE MEMORY B/C/OFF REC R PLAY -00 -20 -10 -6 -3 0 +3 +6 REVERSE dB R AUTO REVERSE EJECT DUBBING NORMAL HIGH O/O CD SUN REC AUTO REVERSE PLAY/AUTO TAPE SELECTOR B POWER AMS AMS A MIC MIX MIC HX-PRO RECORD & PLAY/AUTO TAPE SELECTOR PLAY TAPE MON. REC PLAY(LINE OUT) PHONES REC LEVEL REC BALAMCE Monitor TV 0 10 L R SOURCE MIC *Tape deck or graphic equalizer DIGI-LINK STEREO DOUBLE CASSETTE DECK DD-5080C RESET BC HIGH NORM CD SYN REC L COUNTER A/B MODE M MIN SEC RELAY P MPX T SIZE MEMORY B/C/OFF REC R PLAY -00 -20 -10 -6 -3 0 +3 +6 REVERSE dB R AUTO REVERSE EJECT DUBBING NORMAL HIGH O/O CD SUN REC AUTO REVERSE PLAY/AUTO TAPE SELECTOR B POWER AMS AMS A MIC MIX MIC HX-PRO RECORD & PLAY/AUTO TAPE SELECTOR REC(LINE IN) PHONES REC LEVEL REC BALAMCE 0 10 L R SOURCE MIC q The TAPE MONITOR PLAY/REC jacks may also be connected to the LINE OUT/IN jacks of an optional graphic equalizer. VIDEO OUT S-VIDEO OUT MONITOR MONITOR VIDEO 1 VIDEO 1 IN Manufactured under license from Dolby Laboratories. Dolby , Pro Logic , and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. 1992-1997 Dolby Laboratories. All rights reserved. Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issues and pending. DTS and DTS Digital Surround are trademarks of Digital Theater Systems, Inc. 1996 Digital Theater Systems, Inc. All rights reserved. L R FRONT VIDEO CD OUT S-VIDEO OUT AC INPUT 120V~60Hz 3.5A FRONT SPEAKERS (8) MODEL NO. RD-7106 AUDIO/VIDEO RECEIVER MADE IN KOREA DESIGNED IN USA AUX MONITOR MONITOR REC VIDEO 1 DIGITAL IN PLAY TAPE MON. COAX 1 VIDEO 1 VIDEO 1 SER. NO VIDEO IN VIDEO 1 S-VIDEO IN VIDEO 1 PRE OUT REAR REC R L This device complies with Par t 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. AM LOOP PLAY SUB WOOFER CENTER COAX 2 REC VIDEO 1 VIDEO IN VIDEO 1 S-VIDEO IN VIDEO 1 REAR SPEAKERS (8) AC OUTLETS FRONT OPTICAL 1 PLAY R R FM 75 6-CH DIRECT INPUT REAR OPTICAL 2 VIDEO 2 VIDEO 2 VIDEO 2 29Z3 RISK OF ELECTRIC SHOCK LISTED DO NOT OPEN AUDIO EQUIPMENT CAUTION E85649 VIDEO 2 VIDEO 2 VIDEO 2 SUB WOOFER CENTER VIDEO 3 L R VIDEO 3 VIDEO 3 CENTER SPEAKER(8) SWITCHED 120V~60Hz TOTAL 100W 1A MAX WARNING:"SHOCK HAZARD-DO NOT OPEN" C AVIS;"RISQUE DE CHOC-ELECTRQUE-NE PAS OUVRIR" ANTENNA L R DIGI-LINK " is a trademark of SRS Labs, Inc." VIDEO 3 L R VIDEO 3 VIDEO 3 s CONNECTING ANTENNAS FM (OUTDOOR ANTENNA) AUDIO PLAY (OUT) Video deck 2 POWER ON/OFF MULTIPLE COMPACT DISC PLAYER CDC-5080R V-CD PBC REVERT PEAK PROG AUTO EDIT A B RANDOM SCENE TRACK INDEX GRAPHICS DELETE REPEA T ALL 1 DISC S A< >B MPX INTRO STEP OPEN/CLOSE 1 2 3 4 5 1 4 7 10 13 2 3 5 6 8 9 11 12 14 15 PHONES LEVEL PHONES MIN MAX DVD player MULTIPLE COMPACT DISC PLAYER CDC-5080R POWER ON/OFF S-VIDEO OUT VIDEO OUT AUDIO OUT FM (INDOOR ANTENNA) AM loop antenna 300 ohm feeder AM LOOP SUPPLIED ADAPTOR · The VIDEO 2(or VIDEO 3) jacks may also be connected to an additional video component such as a video deck, a cable TV tuner, an LD player or satellite system. · Use the S-VIDEO jacks to make connections to video components with S-VIDEO IN/OUT jack. · Normal (Composite) Video input signals will generate Composite Video output signals, only. However, S-Video input signals generate both S-Video and Monitor Composite Video outputs. Note : When Sherwood DVD player such as V-756, etc. is connected to the DIGI LINK jack for system control, you should connect the DVD player to the "VIDEO 2" jacks of this unit. Because, if the PLAY button, etc. is pressed on the DVD player, the "VIDEO 2" is automatically selected as an input source on this unit and the playback, etc. starts. 5 ENGLISH VIDEO IN S-VIDEO IN S-VIDEO IN VIDEO IN VIDEO OUT S-VIDEO OUT s CONNECTING SPEAKERS ENGLISH Front right Front left FRONT SPEAKERS (8) R L Rear right REAR SPEAKERS (8) Rear left CENTER SPEAKER(8) IN Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" , and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. 1992-1997 Dolby Laboratories. All rights reserved. Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issues and pending. "DTS" and "DTS Digital Surround" are trademarks of Digital Theater Systems, Inc. 1996 Digital Theater Systems, Inc. All rights reserved. L R FRONT VIDEO CD OUT S-VIDEO OUT AC INPUT 120V~60Hz 3.5A FRONT SPEAKERS (8) MODEL NO. RD-7106 AUDIO/VIDEO RECEIVER MADE IN KOREA DESIGNED IN USA AUX MONITOR MONITOR DIGITAL IN PLAY TAPE MON. COAX 1 VIDEO 1 VIDEO 1 SER. NO PRE OUT REAR REC R L This device complies with Par t 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. AM LOOP SUB WOOFER CENTER COAX 2 REC VIDEO 1 VIDEO IN VIDEO 1 S-VIDEO IN VIDEO 1 REAR SPEAKERS (8) AC OUTLETS E85649 29Z3 LISTED AUDIO EQUIPMENT R FRONT OPTICAL 1 PLAY FM 75 6-CH DIRECT INPUT REAR OPTICAL 2 C CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN R Center VIDEO 2 VIDEO 2 VIDEO 2 SUB WOOFER CENTER VIDEO 3 L R VIDEO 3 VIDEO 3 CENTER SPEAKER(8) SWITCHED 120V~60Hz TOTAL 100W 1A MAX WARNING:"SHOCK HAZARD-DO NOT OPEN" AVIS;"RISQUE DE CHOC-ELECTRQUE-NE PAS OUVRIR" ANTENNA L R DIGI-LINK " is a trademark of SRS Labs, Inc." s CONNECTING DIGITAL INPUTS DIGITAL IN · The speaker terminal are designed to accept either bare wire or banana plugs. · If using bare wire, take care to not allow the + and - wires to touch or short. · Connect the speaker wires firmly and correctly according to the channel and position. Observe the proper polarity (+ and -). · To use two rear center speakers, wire them in series. For more details on series hook-up, consult your dealer or a qualified service organization. · This receiver is designed for use with speakers rated at 8 ohms impedance or above. COAX 1 Component with COAXIAL DIGITAL OUT Component with COAXIAL DIGITAL OUT Component with OPTICAL DIGITAL OUT Component with OPTICAL DIGITAL OUT COAX 2 s CONNECTING SYSTEM CONTROL Sherwood component with DIGI LINK II or III OPTICAL 1 OPTICAL 2 CD player Tape deck DIGI-LINK · The COAXIAL or the OPTICAL DIGITAL OUTs of the components that are connected to CD, VIDEO 1 ~ VIDEO 4 of this unit can be connected to these DIGITAL INPUTS. · A digital input should be connected to the components such as an LD player, CD player, DVD player, etc. capable of outputting DTS Digital Surround, Dolby Digital or PCM format digital signals. · For details, refer to the operating instructions of the component connected. · When making the COAXIAL DIGITAL connection, be sure to use a 75 COAXIAL cable, not a conventional AUDIO patch cord. · Not all of the commercially available Fiber Opticables are suitable for use with this receiver. If you have a questions about the suitability of any cable, please consult your dealer or a qualified service organization. · Remove the protective cap before making OPTICAL connections. Reinsert the protective cap when the OPTICAL input is not being used. System control cord Graphic equalizer DVD player · Interconnect the green system control jacks on compatible Sherwood components that use the DIGI LINK II or III system using standard RCA to RCA cables. 6 s PRE OUT connections L R Power amplifier FRONT PRE OUT Front speakers REAR SUB WOOFER CENTER Power amplifier Rear speakers Power amplifier Center speaker Powered subwoofer · Use these jacks when adding additional amplifiers or powered speakers. · Connect the Pre Out jacks to the corresponding amplifier channels or to the powered speakers as appropriate. · For enhanced deep bass performance, connect a powered subwoofer to the subwoofer output jack. s AC INPUT CORD Plug this cord into a suitable AC outlet. s CONNECTING 6 CH DIRECT INPUTS IN FRONT CH OUT Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" , and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. 1992-1997 Dolby Laboratories. All rights reserved. Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issues and pending. "DTS" and "DTS Digital Surround" are trademarks of Digital Theater Systems, Inc. 1996 Digital Theater Systems, Inc. All rights reserved. L R FRONT VIDEO CD OUT S-VIDEO OUT AC INPUT 120V~60Hz 3.5A FRONT SPEAKERS (8) MODEL NO. RD-7106 AUDIO/VIDEO RECEIVER MADE IN KOREA DESIGNED IN USA AUX MONITOR MONITOR DIGITAL IN PLAY TAPE MON. COAX 1