User manual SHERWOOD SL-8000 - OPERATING MANUAL

Home Theater Master Universal Remote Control SL-8000 Operating Manual Table of Contents Page Introduction Battery Installation A. To Open and Close Battery Compartment Cover B. Low Battery Message Using Your Remote Control A. Function Table Reference Function Tables B. Preprogrammed Set Up Three Digit Code Method Auto Search Method Recalling the Set Up Code Number C. Operation Device Buttons Main Device Mode Automatic Audio Mode Backlighting Advanced Features A. Punch Through Controls Volume "Punch Through" Channel "Punch Through" Transport "Punch Through" B. Memory Buttons Programming Memory Buttons Erasing Memory Buttons C. Changing the LCD Display D. Programming a Second TV, VCR, etc. to other Device Buttons Warranty and Specifications Glossary Appendix Assignment of Audio/Video Equipment Set Up Code Tables Audio Satellite TV VCR Cable CD DVD AUX 2 3 3 3 4 4 5 8 8 10 12 13 14 15 15 16 17 17 17 18 20 22 24 25 26 27 29 30 32 32 33 33 36 38 41 44 46 48 49 1 Introduction The Home Theater Master SL-8000 remote control is preprogrammed to operate over 1,000 Audio and Video components so that you can set it up by simply punching in a three digit code number that matches your equipment. The Home Theater Master SL-8000 remote control operates up to eight different audio and video devices in your home entertainment system. They are listed below: 1 2 3 4 5 6 7 8 TVs, Monitors, Video/LCD Projectors VCRs, TV/VCR combination units Cable boxes, Internet set-tops Satellite receivers - DSS, Primestar, Dish, DBS, C-Band Audio receivers, Preamplifiers, Surround processors Compact disc players, Multi-Disc changers DVD, Laser disc players, Cassette decks Cassette Tape Players, DAT, MiniDisc, Switchers, Lighting, Home Control Devices, and Line Doublers Setting up the remote control to work with your equipment is simple. The remote control also has many advanced features that can add ease and enjoyment to the operation of your home entertainment system. Please follow the instructions in this manual, and retain the manual for future reference. For any questions or comments about this remote control, please contact Universal Remote Control, Inc., 271 North Avenue, New Rochelle, NY 10801, or call (914) 235-2610. Service hours are 9:00 AM to 6:00 PM EST, Monday- Friday. 2 Battery Installation This remote control uses four AAA 1.5 V batteries. Please be sure to match the batteries with the (+) and (­) markings inside the battery compartment during installation. A: To Open and Close the Battery Compartment Cover 1 To open the battery cover, push the latch forward toward the top of the remote control, and lift the latch up. 2 To close the battery cover, slide the battery cover straight back in (toward the top of the remote) and push down until it "clicks" into place. B: Low Battery Message When the Liquid Crystal Display (LCD) flashes L__BAT, the batteries should be replaced. Note: Batteries should last about 6 months under normal conditions. The SL-8000 remote control will retain its programmed memory for up to one year after the batteries are removed and up to ten years after the batteries go "dead". 3 Using Your Remote A: Function Table Reference AUD CD DVD AUX 1 5 9 2 6 3 7 12 4 8 14 15 SAT TV VCR CBL POWER VOL MUTE T/ V CH 10 MENU PAUSE 11 13 GUIDE 21 16 22 R E W SEL PLAY F . F 19 20 18 STOP EXIT PRE. CH 23 17 24 1 4 7 2 5 8 0 3 6 9 ENTER SHIFT FAV SLEEP 25 28 31 35 41 42 26 29 32 34 43 27 30 33 36 44 37 38 39 40 45 INFO PRO.L NEXT 3.CH +10 PIP ALT TEST TUNER CD TAPE1 TAPE2 PHONO 46 VCR1 VCR2/SAT LDP AUX TV 47 48 49 50 M1 M2 M3 M4 51 52 55 53 54 LIGHT HOME THEATER MASTER SL-8000 4 Using Your Remote Function Table No. 1-8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25-34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Button Name Device Name Power Mute T/V Input VOL Up VOL Down CH Up CH Down Up/Pause Down/Stop Right/F.F. Left/Rew Sel/Play Guide/I<< Menu/>>I Exit/Rec Pre. Ch./Eject 1--0 10+ Enter/Shift Fav/Sleep Info/Pro. L. Next/3 Ch. Alt/Test Tuner CD Tape 1 Tape 2 Phono VCR1 VCR2/SAT LD/DVD Aux TV M1 M2 M3 M4 Light Audio Functions AUDIO (ON) On/Off (OFF) Mute Band/FM Vol Up Vol Down Preset + Preset Center + Center Rear + Rear Select/Sub.Bass Display Surround Delay Delay+ 1--0 Plus 10 Shift Sleep Pro. Logic 3 Ch. Test Tone Tuner/AM/FM CD Tape 1 Tape 2 Phono VCR1 VCR2 LD/DVD Aux TV SAT Functions SAT (ON) On/Off (OFF) Mute TV/SAT Vol Up Vol Down Ch. Up Ch. Down Up Down Right Left Select Guide Menu Exit/Cancel Prev. Ch. 1--0 Enter Fav Info/Fetch Next Prog. Alt. Audio TV Functions TV (ON) On/Off (OFF) Mute TV/Video Vol Up Vol Down Ch. Up Ch. Down Up Down Right/Picture Left/Audio Select/Enter Display/Recall Menu Exit/Clear Q. View/Last Ch. 1--0 100/Ch. Scan Ch. Scan Sleep Caption Ant Reset PIP On/Auto Ch. PIP Swap, Add PIP Freeze/Delete PIP Off/Position TV/CATV Auto Add Delete Rec. 5 Using Your Remote Function Table No. 1-8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25-34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Button Name Device Name Power Mute T/V Input VOL Up VOL Down CH Up CH Down Up/Pause Down/Stop Right/F.F. Left/Rew Sel/Play Guide/I<< Menu/>>I Exit/Rec Pre. Ch./Eject 1--0 10+ Enter/Shift Fav/Sleep Info/Pro. L. Next/3 Ch. Alt/Test Tuner CD Tape 1 Tape 2 Phono VCR1 VCR2/SAT LD/DVD Aux TV M1 M2 M3 M4 Light VCR Functions VCR (ON) On/Off (OFF) Mute VCR/TV Vol Up Vol Down Ch Up Ch Down Pause Stop Fast Forward Rewind Play F. Adv./Slow< X2/Intro/Slow> Record Eject 1--0 1--100 Enter Program Display C-Counter Reset Auto Ch Add + Delete Tape Speed VCR Plus Tracking + Tracking Auto Tracking Slow Slow + Index QTR On QTR Off Edit Cable Functions CABLE (ON) On/Off (OFF) Mute Switch/A/B Vol Up Vol Down Ch Up Ch Down Up/Fine + Down/Fine Right/Fine R Left/Fine L Select Guide/Recall Menu Exit Prev. Ch 1--0 */Help Enter/Memory Fav Info PPV/Buy P/Delete Page Page + Day -. Day + Record 6 Using Your Remote Function Table No. 1-8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25-34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Button Name Device Name Power Mute T/V Input VOL Up VOL Down CH Up CH Down Up/Pause Down/Stop Right/F.F. Left/Rew Sel/Play Guide/I<< Menu/>>I Exit/Rec Pre. Ch./Eject 1--0 10+ Enter/Shift Fav/Sleep Info/Pro. L. Next/3 Ch. Alt/Test Tuner CD Tape 1 Tape 2 Phono VCR1 VCR2/SAT LD/DVD Aux TV M1 M2 M3 M4 Light CD Functions CD (ON) On/Off (OFF) Mute/Fader Random Vol Up Vol Down Track +/Skip + Track-/Skip Pause Stop FF/Search + REW/Search Play Search Search + Eject/Intro 1--0 Plus 10 Disc Program Display Repeat Clear Disc 1 Disc 2 Disc 3 Disc 4 Disc 5 A-B Time Intro Edit DVD Functions DVD (ON) On/Off (OFF) AUX Functions TAPE (ON) On/Off (OFF) Mute/Rec Mute Skip >>I Skip I<< Pause Stop F.F. REW Play Set Up Menu Clear Open/Close 1--0 10+ Enter Return Display Sub. On/Off Audio Up Down Select Angle Slow Left Right Subtitle Repeat Random A/B Repeat T Title Memory Pause Stop F.F. REW Play Deck A Deck B Record Rev. Play Deck A Deck B REW For. Play F.F. Stop REV. Play Pause Record 7 Using Your Remote B: Preprogrammed Set Up The Home Theater Master universal remote control can operate up to eight separate audio and video devices (equipment). To program the remote control for your devices, please use the following steps: Three Digit Code Method 1 Turn on the device you would like the remote control to operate, either manually or with your original remote control. 2 Find the three digit Set-Up Code number for your device from the tables on pages (33~50). Example: To set up the remote to operate with a ZENITH TV, go to the TV Set-Up Code table found on pages (38 40) and look for ZENITH under the Manufacturer/Brand column. You will find that the Set-Up Code numbers for ZENITH TVs are 072, 073, 095, 103 and 157. 3 Press the corresponding Device Button (TV, VCR, SAT, CBL, AUD, CD, DVD, or AUX) and the MUTE button on the remote control simultaneously. SET will appear in the LCD. AUD CD DVD AUX Device Buttons SAT TV VCR CBL POWER VOL CH Mute Button MUTE T/ V GUIDE GUIDE PAUSE PAUSE MENU MENU Example: To set-up the remote to operate a TV, press the TV Device Button and the Mute button, simultaneously. R R E E W W SEL PLAY PLAY F .F . F F STOP STOP EXIT 8 3 6 9 PRE. CH 1 4 7 2 5 8 0 FAV SLEEP SLEEP INFO PRO.L PRO.L NEXT 3.CH 3.CH +10 PIP PIP ENTER SHIFT SHIFT ALT TEST TEST TUNER CD TAPE1 TAPE2 PHONO Using Your Remote Note: SET appears in the LCD for 20 seconds to indicate that the remote control is ready to be programmed. The following steps must be entered while SET appears in the LCD. 4 Point the remote control toward the device that was turned on in Step 1 and press in the first three-digit SetUp Code number for that device using the number buttons (0-9) on the remote control. SET followed by the number will appear in the LCD. Your device will turn off when the correct Set-Up Code number has been selected. If the device does not turn off, press in the next Set-Up Code number from the listing. Continue to select Set-Up Code numbers until your device turns off, before you proceed to Step 5. Note: If you have tried all of the three digit Set-Up Code numbers listed for your device and it still did not turn off, please proceed to the Auto Search Method on page (10) to program your remote control. 5 Once your device turns off, press the Device Button selected in Step 3 once again to store the Set-Up Code number. PASS will flash in the LCD. 6 Test the remote control for your device. Try the POWER, CHANNEL UP AND DOWN, VOLUME UP AND DOWN buttons, etc. If any of the buttons do not perform as they should, please repeat the set-up from Step 1 using the next Set-Up Code number for your device. Note: Some audio/video devices have separate buttons for POWER ON and POWER OFF. To operate these devices on the remote, press the corresponding DEVICE Button to turn the equipment ON and press the POWER button to turn the equipment OFF. 7 Please repeat the above steps to program the remote control for each of your other devices. 9 Using Your Remote Auto Search Method Please use this method if none of the Set-Up Code numbers worked for your device during the standard set-up procedure or if the manufacturer or brand for your device is not listed in Set-Up Code Tables. 1 Turn on the device you would like the remote control to operate, either manually or with your original remote control. 2 Press the corresponding Device Button (TV, VCR, SAT, CBL, AUD, CD, DVD, or AUX) and the MUTE button, simultaneously. SET will appear in the LCD. AUD AUD CD CD DVD DVD AUX AUX Device Buttons SAT SAT TV TV VCR VCR CBL CBL POWER POWER VOL VOL CH CH Channel Buttons Mute Button MUTE MUTE T/ V T/ V GUIDE GUIDE PAUSE PAUSE MENU MENU Note: SET appears in the LCD for 20 seconds to indicate that the remote control is ready to be programmed. The following steps must be entered while SET appears in the LCD. R R E E W W SEL SEL PLAY PLAY F .F . F F STOP STOP 3 Point the remote control toward the device and press the EXIT EXIT PRE. PRE. CH CH CHANNEL UP button on the remote control. Each but1 2 3 2 3 ton press sends the1 signal for one Set-Up Code number. 4 5 4 6 Keeping the CHANNEL5 UP6 button pressed produces a quick scanning of the Set-Up99 Code numbers. 7 8 7 8 Release the CHANNEL UP button as soon as the device +10 0 +10 0 turns off. Please confirm that you have the correct code by pressing the MUTE button on the remote. You should be able to turn your device on and off with this button. FAV FAV SLEEP SLEEP INFO INFO PRO.L PRO.L NEXT NEXT 3.CH 3.CH ENTER ENTER SHIFT SHIFT ALT ALT PIP PIP TEST TEST TUNER TUNER CD CD TAPE1 TAPE1 TAPE2 PHONO TAPE2 PHONO VCR1 VCR2/SAT LDP VCR1 VCR2/SAT LDP AUX AUX TV TV M1 M1 M2 M2 M3 M3 M4 M4 LIGHT LIGHT HOME THEATER MASTER HOME THEATER MASTER LEARNING REMOTE CONTROL LEARNING REMOTE CONTROL 10 Using Your Remote If you pass the correct Set-Up Code number, you can return to it by pressing the CHANNEL DOWN button, one Set-Up Code number at a time, until your device turns back on. Note: During programming, the signal for POWER ON and POWER OFF is located on the MUTE button. For devices that use separate POWER ON and POWER OFF buttons, pressing the MUTE button on the remote control during programming will only turn the device OFF. 4 Once the correct code is confirmed, press the Device Button to store the Set-Up Code number. PASS will appear in the LCD. 5 Test the remote control for your device. Try the POWER, CHANNEL UP AND DOWN, VOLUME UP AND DOWN buttons, etc. If any of the buttons do not perform as they should, please repeat the set-up from Step 1 using the next Set-Up Code number for your device. Note: Some audio/video devices have separate buttons for POWER ON and POWER OFF. To operate these devices on the remote, press the corresponding DEVICE Button to turn the equipment ON and press the POWER button to turn the equipment OFF. 6 Please repeat the above steps to program the remote control for each of your other devices. 11 Using Your Remote Recalling the Set-Up Code Number To display the three digit Set-Up Code number that was stored for a device. 1 Press the Device Button and the MUTE button, simultaneously. SET will appear in the LCD. 2 Press the T/V button. The LCD will quickly flash the three digit Set-Up Code number that was stored for your device in that mode. 3 Please write your Set-Up Code numbers in the chart below, for future reference. Set-Up Code Numbers: Audio SAT TV VCR Cable CD DVD AUX 12 Using Your Remote C: Operation After you have programmed the remote control for your equipment, use the following procedures to operate your home entertainment system: 1 Press the Device Button that you wish to operate: e.g. to operate a TV, press the TV Device Button; to operate a VCR, press the VCR Device Button, etc. 2 Aim the remote control at the device and press the POWER button to turn on the device. 3 Press the buttons that send out the commands you desire. Note: Some audio/video devices have separate buttons for POWER ON and POWER OFF. To operate these devices on the remote, press the corresponding DEVICE Button to turn the equipment ON and press the POWER button to turn the equipment OFF. Please try all the functions of this remote control with your equipment. The most common functions are labeled on the remote. However, some of the secondary functions might be stored under a button that has a different name from the one on your original remote control. Please refer to the Function Tables on pages (5 - 7) for details. 13 Using Your Remote Device Buttons Any press of a Device button at the top of the remote control can perform the following functions: 1 Changes the Device mode on the SL-8000 remote control. 2 Sends out a preprogrammed POWER ON command for a AUD AUD CD CD DVD DVD AUX AUX SAT SAT TV TV VCR VCR CBL CBL Device, if applicable. 3 Sends out a joined selection. 4 Toggles between the Main Device mode and the Automatic VOL CH MUTE MUTE T/ V T/ V POWER Audio mode if the Automatic Audio Mode is active. GUIDE GUIDE MENU MENU PAUSE PAUSE Joining to Device Buttons R R E E W W SEL SEL PLAY PLAY F F .. F F The 10 preprogrammed Audio input selects and the keypad buttons 0-9 found on the SL-8000 in the AUDIO Device mode can be joined to individual Device buttons. Once joined, any press of 1 the Device button will also emit the 2 3 joined command. STOP STOP EXIT EXIT PRE. PRE. CH CH FAV FAV SLEEP SLEEP 4 AUD 5 CD 6 DVD INFO INFO PRO.L PRO.L AUX 7 SAT 8 TV 9 VCR ENTER ENTER SHIFT SHIFT NEXT NEXT 3.CH 3.CH CBL Device Buttons +10 PIP PIP 0 ALT ALT TEST TEST POWER TUNER TUNER MUTE TAPE1 CD TAPE1 CD T/ V VOL TAPE2 PHONO TAPE2 PHONO CH Audio Input Buttons VCR1 VCR2/SAT LDP AUX VCR1 VCR2/SAT LDP AUX GUIDE M1 M2 M3 M1 M2 M3 PAUSE TV TV MENU M4 M4 Setting Up: 1 Press the AUDIO and ENTER buttons simultaneously on R E W LIGHT LIGHT SEL PLAY F . F the remote control. JOIN will appear in the LCD. LEARNING REMOTE CONTROL LEARNING REMOTE CONTROL STOP HOME THEATER MASTER 2 Press the Device button that you would like to assign a EXIT PRE. CH joined function. CLEAR will flash and INPUT will then 1 2 3 appear in the LCD. FAV SLEEP 3 Select a button to be joined from the remote control, e.g. , PRO.L 4 5 6 INFO 7 VCR1, VCR2, CD, etc. or 81, 1, 9 etc.). The LCD will display 2 IN_XX indicating +10 0Audio input selected (IN_V1, the IN_V2, IN_CD, etc. or IN_0, IN_1, IN_2 etc.) and then JOIN. NEXT 3.CH ENTER SHIFT ALT PIP TEST TUNER CD TAPE1 14 TAPE2 PHONO VCR1 VCR2/SAT LDP AUX TV M1 M2 M3 M4 LIGHT HOME THEATER MASTER LEARNING REMOTE CONTROL Appendix A: Assignment of Audio/Video Equipment Please use the following listing to locate the correct Set-Up Code Tables for your equipment: AUDIO Set-Up Code Table: Audio Receivers, Preamplifiers, Surround Processors Satellite Set-Up Code Table: DSS, Primestar, DBS, Echostar, C Band receivers TV Set-Up Code Table: TVs, Monitors, Video/LCD Projectors VCR Set-Up Code Table: VCRs, TV/VCR combination units CABLE Set-Up Code Table: Cable Boxes, Internet/TV Set-Tops CD Set-Up Code Table: CD Players, CD Changers DVD Set-Up Code Table: DVD Players, Laser Disc AUX Set-Up Code Table: Cassette Tape Players, DAT systems, MiniDisc, Switchers, Lighting, Home Control Devices, and Line Doublers 32 Glossary Punch Through Advanced feature that enables you to operate Volume, Channel or Transport Control functions of one device while in another mode. Example: Audio Volume Control "Punch Through" gives you the ability to raise, lower and mute your Audio receiver volume while operating the remote control in the TV mode. Set-Up Code Number The three-digit number that is used to program the remote control for your particular manufacturer or brand of audio/ video equipment. Set-Up Code numbers are located in tables in the appendix on pages 33 - 50 of the instruction manual. Set-Up Code numbers are categorized by type of device, e.g. TV, VCR, Audio, CD, DVD, Cable, AUX and Satellite. More than one Set-Up Code number may work with your device. You should test the functions for each of the Set-Up Code numbers that work with your device to determine the best Set-Up Code number for your particular device. Note: Some devices, such as CD players and DVD Decks that do not have POWER buttons on their original remote controls, may not shut off during programming. For these devices, it may be necessary to first store the Set-Up Code number and then test functions like PLAY, STOP, etc., to determine if the correct SetUp Code number has been selected. Transport Control Buttons that correspond to the PLAY, STOP, REWIND, FAST FORWARD, PAUSE, SEARCH/SKIP and RECORD functions on your audio/video equipment. 31 Using Your Remote 4 Press the ENTER button. SAVE will flash twice and the LCD will return to AUDIO indicating that the joined function has been stored. Every time that the Device button is pressed it will also emit the joined function. To erase a joined function from a Device button: 1 Press the AUDIO and ENTER buttons simultaneously on the remote control. JOIN will appear in the LCD. 2 Press the Device button that you would like to erase a joined function. CLEAR will flash and INPUT will then appear in the LCD. 3 Press the ENTER button. The LCD will flash SAVE twice and return to AUDIO indicating that the join has been erased. Main Device Mode When the main device is displayed in the LCD, the SL-8000 will perform all of the preprogrammed, joined and punch through features for that device mode. Automatic Audio Mode The remote is defaulted to the Automatic Audio. When the remote control is in this mode, pressing a Device button a second time will display A_XXX in the LCD indicating that the Volume and Mute controls of the device programmed into the Audio mode of the SL-8000 is active, while full function control of all other buttons of the current Device mode is maintained. Main Device Mode Automatic Audio Mode 15 Advanced Features After you set-up the remote control to operate your equipment, you can also program advanced features on the remote control. The advanced features are designed to enhance the use of the remote control with your home entertainment system. A: Punch Throughs Volume Control "Punch Through" You can program the remote control so that either the AUDIO or TV Volume Control (VOLUME UP, DOWN AND MUTE) will also operate in other modes on the remote control. Example: Raise, lower and mute the VOLUME of your Audio receiver while the remote control is in the Satellite mode. Note: When this feature is active, the AUDIO or TV VOLUME and MUTE will override any existing volume controls in that mode. To Set-Up: 1 Select the mode that you wish to program for Volume Control "Punch Through." 2 Press the corresponding Device Button and the MUTE button simultaneously. SET will appear in the LCD. 3 Press the VOLUME UP button. PUNCH will appear in the LCD. 4 Press either the AUDIO Device Button to set-up for Audio Volume Control or the TV Device Button to set-up for TV Volume Control. AUDIO or TV will flash in the LCD, depending on which Device Button was selected. AUDIO or TV Volume Control will now override the original VOLUME and MUTE in this mode. 17 Glossary Cursor Control Buttons that correspond to the UP, DOWN, LEFT, RIGHT, SELECT, GUIDE, MENU and EXIT functions of your audio/video equipment. Device Audio or video equipment, e.g. Television, VCR, Cable box, Audio receiver, Satellite receiver, etc. Device Button Any of the eight buttons located at the top of the remote control labeled AUD, CD, DVD, AUX, SAT, TV, VCR and CBL. Device Buttons are used to select modes of operation and to program the remote control. Joining Transfer of a function from the AUDIO input selects and keypad(0-9) on the SL-8000 to a Device button at the top of the remote control. LCD Liquid crystal display window located at the top of the remote control. During normal operation the LCD indicates the mode. The LCD also indicates the remote's programming status. Memory Buttons Buttons labeled M1, M2, M3, M4, and POWER. These buttons can be programmed to store Favorite Channels, Macro Commands, or to "relocate" functions from one mode to another. Modes Modes correspond to Device Button selections. Modes are displayed in the LCD as AUDIO, CD, DVD, AUX, SAT, TV, VCR and CABLE. Modes indicate the type of device the remote control is currently operating. 30 Warranty The Home Theater Master SL-8000 remote control comes with a one-year warranty from the date of purchase. Specifications Model SL-8000, infrared remote control. Power Four 1.5 V AAA Batteries. Dimensions (h/w/d) 8.88 x 2.5 x 1.25 inches Weight 6.5 oz. (with batteries) 29 Advanced Features To Return to the Original Setting: 1 Select the mode that you want to turn off the Volume Control "Punch Through." 2 Press the corresponding Device Button and the MUTE button simultaneously. SET will appear in the LCD. 3 Press the VOLUME UP button. PUNCH will appear in the LCD. 4 Press the Device Button again. The DEVICE Mode will flash in the LCD. The AUDIO or TV Volume Control "Punch Through" is now turned off. The VOLUME and MUTE of the original device will operate on the remote control. Channel Control "Punch Through" You can program the remote so that either the SAT or Cable Channel Controls (CHANNEL UP and DOWN) will also operate in other modes on the remote control. Example: Change CHANNELS UP and DOWN on your cable box while the remote is in the TV mode. Note: When this feature is active, SAT or Cable CHANNEL UP and DOWN will override any existing channel controls in that mode. To Set-Up: 1 Select the mode that you wish to program for Channel Control "Punch Through." 2 Press the corresponding Device Button and the MUTE button simultaneously. SET will appear in the LCD. 3 Press the VOLUME DOWN button. PUNCH will appear in the LCD. 18 Advanced Features 4 Press either the SAT Device Button to set-up for SAT Channel Control or the CBL Device Button to set-up for Cable Channel Control. Either SAT or CBL will flash in the LCD, depending on the Device Button selected. SAT or Cable Channel Controls will now override the original CHANNEL UP and DOWN in this mode. To Return to the Original Setting: 1 Select the mode that you want to turn off the Channel Control "Punch Through." 2 Press the corresponding Device Button and the MUTE button, simultaneously. SET will appear in the LCD. 3 Press the VOLUME DOWN button. PUNCH will appear in the LCD. 4 Press the same Device Button again. The DEVICE Mode will flash in the LCD. The SAT or Cable Channel Control "Punch Through" is now turned off. The CHANNEL UP and DOWN of the original device will now operate on the remote control. 19 Advanced Features Your device will turn off when the correct Set-Up Code number has been selected. If it does not turn off, select the next Set-Up Code number from the table, and press in that code number. When your device turns off, proceed to Step 6. 6 Press the Device Button that was selected in Step 2. to store the Set-Up Code number. PASS will flash in the LCD to confirm the programming. The second device can now be operated by pressing the assigned Device Button and using the buttons within this mode. 28 Advanced Features LCD Displays in the Automatic Audio Mode A_TV A_DVD A_AM2 A_PRJ A_AV A_VCR A_AUX A_TA1 A_AX2 A_TAP A_CAB A_TV2 A_TA2 A_LD A_DAB A_SAT A_VC2 A_WEB A_A2 AUDIO A_TUN A_SUR A_LIT A_CD A_AM1 A_DAT A_DSS D: Programming a Second TV, VCR, etc. to Other Device Buttons. This feature is used to program the remote control for two or more TVs, VCRs, etc., or to program a device into a mode with a different Device Button name. You can store the three-digit Set-Up Code number for any device into any other unused Device Button. Example: If your home entertainment system contains two VCRs. First, using the VCR Device button, program the remote via standard set-up to operate the first VCR. Then, program your second VCR into a Device Button that is not being used, e.g., AUX using this method. 1 Turn on the device. 2 On the remote control, press the Device Button that you will assign for the device and the MUTE button, simultaneously. SET will appear in the LCD. 3 Press the Device Button that corresponds to the original device. SET will still appear in the LCD. 4 Locate the Set-Up Code number for the device from the tables found on pages (33 - 50).