s mobile s mobile Issued by Information and Communication mobile Haidenauplatz 1 D-81667 Munich © Siemens AG 2004 All rights reserved. Subject to availability. Rights of modification reserved. Siemens Aktiengesellschaft www.siemens-mobile.com/cx70emoty Designed for life CX70 Emoty Overview (en) 3 Overview (en) 1 1 Emoty device. The Emoty device is fitted like a CLIPItTM cover, p. 7. p. 8. 2 Studs for opening the Emoty cover, 3 Emoty start screen. This appears when the Emoty application has started, p. 10. Emoty 2 3 4 4 Emoty sensors. You can control the Info ì Options 5 6 7 intensity and expression of the animated figure with the three built-in sensors. The stroking and pressing sensors are on the sides. The shaking sensor is built into in the CLIPItTM cover, p. 10. 5 Display buttons 6 Joystick. You can use the joystick I to select a figure (p. 10). 7 Emotion keys 0 - 9. Use these buttons to select the emotions that you would like to send (p. 12). The emotion keys only become active after you have started the Emoty application. This user handbook uses the same symbols and menu guidance as those shown in the user handbook of your mobile telephone. 4 Table of Contents Table of Contents Overview (en) ............................ 3 Table of Contents ....................... 4 Introduction ............................... 5 Welcome ................................. 5 Safety precautions ................... 5 Getting started ........................... 7 Installing Emoty on your telephone ................................ 7 Disassembling your telephone ............................ 7 Install Emoty ........................ 7 Uninstalling the Emoty ......... 8 Software installation ................ 9 Download ............................ 9 Upload from a PC ................. 9 Using Emoty ............................. 10 Start Emoty ............................ 10 Ending Emoty ........................ 10 Creating emotions ................. 10 Select a figure with the joystick ......................... 10 Assigning an emotion ......... 11 Changing the emotion ........ 11 The fun button ................... 12 Sending emotions by MMS ..... 12 Sending emotions ............... 13 Send display ....................... 13 Adding text ......................... 14 Saving text ......................... 14 Resetting the emotion ........ 15 Changing the resolution of the animation ................. 15 Setup ........................................ 16 Downloading new figures ....... 16 Downloading new emotions ... 16 Deleting a figure/emotion ....... 16 Adjusting and testing sensor settings .................................. 17 Dynamic Light .................... 17 Appendix .................................. 18 Self help for problems ............ 18 Customer Care ....................... 18 Care and maintenance ............ 19 Battery quality declaration ...... 19 Display quality declaration ...... 19 Technical data .................... 20 Operating times .................. 20 Guarantee certificate (UK) ...... 20 Guarantee certificate (IRL) ...... 21 SAR ­ European Union (RTTE) . 22 SAR ­ International (ICNIRP) ... 23 Introduction 5 Introduction Welcome Your Emoty lets you express your emotions in a completely new way and send them immediately by MMS to your friends and acquaintances. · Choose one of three figures, p. 10. · Choose one of 10 different emotions, p. 11. · Show your feelings to the figure by pressing, stroking or shaking your telephone, p. 11. · Add a text and send the emotion immediately by MMS, p. 12. · Download new figures from the Internet, p. 16. Remember to comply with legal requirements and local restrictions when using the phone. For example in aeroplanes, petrol stations, hospitals or while driving. Mobile phones can interfere with the functioning of medical devices such as hearing aids or pacemakers. Keep at least 20 cm/ 9 inches between phone and pacemaker. When using the mobile phone hold it to the ear which is further away from the pacemaker. For more information consult your doctor. Message tones are reproduced through the loudspeaker. Do not hold the telephone to your ear when it rings. Otherwise you risk serious permanent damage to your hearing. Safety precautions Information for parents Please read the operating instructions and safety precautions carefully before use. Explain the content to your children and the hazards associated with using the phone. 6 Introduction Only use original Siemens batteries (100% mercury-free) and charging devices. Otherwise you risk serious damage to health and property: the battery could explode, for instance. You may only open the phone to replace the battery, faceplate, keypad or SIM card. You must not open the battery under any circumstances. Any other changes to this device are strictly prohibited and will invalidate the operating licence. Important Dispose of used batteries and phones according to the legal regulations. Mobile phones can interfere with the operation of nearby TVs, radios or PCs. Use only Siemens original accessories. This will avoid potential risks to health or property and ensure compliance with all relevant regulations. Improper use will invalidate the guarantee! These safety instructions also apply to Siemens original accessories. Getting started 7 Getting started Installing Emoty on your telephone If you have a CX70 Emoty, you only need to insert the SIM card and fit the Emoty cover before you can "get going" (p. 10)! If you have a separate CX70 Emoty cover, you need to install the Emoty application and Emoty animations on your telephone as well, p. 9. Before fitting the Emoty cover, switch your telephone off! Install Emoty Insert the telephone in the lower shell Disassembling your telephone · If necessary, disassemble your telephone according to the instructions in the user handbook of your telephone. · Remove the old keypad. 1 Hold the telephone with the display facing upwards. Insert the lower edge of the telephone at an angle into the lower shell of the Emoty cover. Make sure that the telephone is inserted under the contact pin of the Emoty! 2 Carefully press on the upper shell of the telephone until it clicks into place in the lower shell. Place the new keypad on the telephone. Make sure that it is seated correctly. Emoty keyboard The new keyboard lets you select Emotions by pressing the symbols (p. 11). If the Emoty application is switched off, the keyboard functions like your normal telephone keyboard. 8 Getting started Fitting the upper shell Uninstalling the Emoty Remove the upper shell of the Emoty cover 1 Insert the stud on the bottom of the upper shell into the corresponding recess of the Emoty lower shell. it clicks into place. 2 Carefully press on the upper shell until Note Please check that all sides of the upper shell have clicked correctly into place. 1 Press on the side studs (p. 3) until the upper shell springs open. angle and remove it. 2 Pull the upper shell forwards at an Removing the telephone Tilt the lower shell forwards and take out the telephone. You can carefully tap the lower shell against your hand so that the telephone comes out gently. Getting started 9 Software installation If you upgrade one of the telephones of the CX70 series to Emoty, you must first install the Emoty application with the animations on your telephone. Requirement: Your telephone must have an Emoty hardware interface. Please ask your dealer for details. Requirements · The telephone is switched on. · You have connected your telephone to your PC via the data cable or via the IrDA interface. Installation · Insert the CD in the CD drive of your PC. · Start the Mobile Phone Manager (Requirement: The program is installed). · Copy the Emoty folder and all its contents from the CD onto the telephone. Further information is available on the CD or on the Internet under www.siemens.com/ cx70emoty. You must then disconnect the telephone from your PC. Now you can start the Emoty application on the telephone. Requirement: You have already fitted the Emoty cover (p. 7) Note If you have any questions or problems about the software installation, please contact our customer service, p. 18. Download C¢O¢Applications I C Or Select Emoty. Start the browser. §Options§ Go to... C¢O¢Internet Open menu. Select and enter wap.siemensmobile.com/emoty. Start the download. C Upload from a PC You can load the software from a PC to the telephone. The software necessary for this is available on the enclosed CD. You can install it on the telephone from your PC. Further information about the installation is available on the Internet under www.siemens.com/ cx70emoty. 10 Using Emoty Using Emoty The user handbook uses the same symbols and menu guidance as those shown in the user handbook of your mobile telephone. Ending Emoty §Options§ Exit §Yes§ §No§ Open menu. Select this function. Emoty is ended. Process is stopped. Start Emoty If you have fitted the Emoty cover on your telephone, there are two ways of starting Emoty. Either: §Emoty§ Press this display button. If this display button is not yet assigned to the Emoty application, you must change the assignment first. For details of how to do this, read the user handbook of your telephone. Or: Start the Emoty application via the Surf & Fun menu of your telephone. Creating emotions Select a figure with the joystick After you have started Emoty, the start display appears. A figure is already selected. If you like it, you can assign it your emotions (p. 11). If you want to select another figure: I Select a figure. Emoty C¢O¢Applications Emoty is started. ¢Emoty Note The Emoty application must be installed (p. 9). Info í Options Under each figure, the emotions which can be selected are highlighted. You can, however, also download new figures and/or emotions (p. 16). Using Emoty Note The last figure you selected is automatically loaded when the Emoty application is restarted. 11 Press one of the buttons 0 to 9 to assign this emotion to your figure. After selecting an emotion the selected figure displays this emotion and can only be changed by you. Assigning an emotion You can now assign an emotion to the selected figure. You can choose between the following emotions: Icon/button Emotion Love Happy Curious Surprise Apology Naughty Boredom Sad Anger Fun Changing the emotion Your Emoty cover has three sensors which can be used to change the emotion of your figure: · Pressing. Press on the left or right sensor (p. 3). · Stroking. Stroke the left or right sensor (p. 3). · Shaking the telephone. Note You can adjust the sensitivity of the sensors, p. 17. Effects of positive emotions If you have selected one of the positive emotions 1 to 5, this means: · Stroking a sensor strengthens the emotion · Pressing a sensor weakens the emotion 1 2 3 4 5 6 7 8 9 0 12 Using Emoty Effects of negative emotions If you have selected one of the negative emotions 6 to 9, stroking or pressing causes exactly the opposite effect, i.e. · Stroking a sensor weakens the emotion · Pressing a sensor strengthens the emotion As soon as you operate the sensor, you see the figure react. Strength of the reaction The sensors react at three levels: The stronger you stroke or press a sensor, the more intensive the figure displays the emotion. In both cases if you shake your telephone, the expression of your figure changes, while the intensity of its emotion remains the same. Resetting the emotion Press the B button to reset your figure to the original animation. If the figure is already in the initial state, it is reset to the start display. The fun button The fun button 0 is an exception. It is not used to express a specific emotion, but rather to send birthday greetings or invitations to your friends for example. Shaking several times lets you choose different templates. Just like the positive emotions, stroking strengthens and pressing weakens the chosen template. Sending emotions by MMS You can send the emotion you created by MMS to the MMS-capable telephone of your friends or acquaintances and add a text. Requirement Your service provider offers the MMS service. You may have to register specially to use this service. Using Emoty 13 Sending emotions First assign an emotion and change it as you want. Then: §Options§ Send Open menu. Select this function. The send display appears. Select the input fields you want. Fill out input fields. The size of the MMS appears in the last line Size:. A lower resolution results in a smaller MMS. Preview §Options§ Preview Open menu. Select this function. I J To: A preview of the MMS appears. Briefly press the B button to return to the menu. Sending to a number of recipients §Options§ Open menu. Cc: Select this function. Select the address line and enter the telephone number. You can also choose an entry from the address book or from the telephone ...