RTX 55H User and Installation Manual Look Forward cod.46.0360.200 BACK LIGHT Turns on the back light LIGHT STAND-BY Switches off to stand-by. 0-9 Keys Switch on from stand-by and allow direct source selection. ESCAPE Deactivates the On Screen Display. SOURCE Displays the Source Selection menu. Not active in this model. Up/Down/Left/Right Arrow keys Navigate through and make adjustments to the On Screen menus. Arrow Up/Down activate Quick menus. MENU + Activates the On Screen Display menus. Navigates menu pages. MEMORIES Activates Memories menu ZOOM MENU Activates the On Screen Display menus. Navigates menu pages. FREEZE Freezes a moving picture. F1 F1 Multifunction key F2 FOCUS INFO Displays the selected source information and the projector status. F2 Multifunction key VCR AUTO Selects Auto Adjust (automatic optimisation of the displayed image). Improves the video recorder signals quality. ASPECT Selects image Aspect ratio. 1 INTRODUCTION Congratulations on your choice of the SIM2 Grand Cinema RTX 55H system! P ROSSECOR EGAMI TM C ITPOIGID NO FFO 1 The RTX system combines the signal processing capabilities of the DigiOpticTM Image Processor with the high fidelity reproduction of the DLPTM technology Display by linking the two units via a fibre optic cable. The DigiOpticTM Image Processor, which should be ideally located close to the signal sources, supports and processes a wide range of video signals, transmitting them to the display by means of a fibre optic link cable. The large number of inputs available (2 Composite Video inputs, 2 S-Video inputs, up to 4 Component or RGB inputs, 2 graphic RGB inputs and 1 DVI-D input,1HDMITM) ensures the system supports a wide variety of analogue and digital sources: DVD players, VCRs, satellite and terrestrial receivers, computers, game consoles, video cameras, etc. The signal processing capabilities of the Image Processor ensure optimum reproduction of a broad range of input signals, from interlaced video to high definition and graphics. Conversion of interlaced video signals to progressive signals by means of prestigious DCDiTM technology produces fluid, natural, images free of flicker and stairstepping artefacts. Faithful reproduction of signals at higher resolutions (such as high definition video and graphics) occurs without loss of information or reduction of image sharpness thanks to the processor's high pixel rate signal acquisition capabilities. Adaptation of the input signal resolution to the Display resolution occurs without alterations of image quality, in accordance with an ample choice of aspect ratios, including several definable by the user. All image adjustments can be performed with the remote control with the aid Ôf the On Screen Display; alternatively, the unit can be controlled by from a home automation system through the serial port. The Display, with its elegant and original design, produces an image using the very latest Texas Instruments DLPTM technology (1280x720 pixel DMDTM panel with 12° technology), a proprietary dust-sealed optical system, a new six-segment colour wheel and a new type of Fresnel lens. All these features combine to provide a top quality image, with definition, sharpness, colorimetry and contrast on a par with the famous frontal Displays in SIM2's Grand Cinema line. The two units are connected via a three-core fibre optic cable for transmission of the digital signal from the DigiOpticTM Image Processor to the Display and control signals in both directions. Transmission occurs without interference or attenuation over distances of up to 500 m. Moreover, the flexibility and small size of the cable allow the maximum freedom when installing the system in your home. SIM2 carries out comprehensive functional testing in order to guarantee the maximum product quality. For this reason, when you start using the product lamp operating hours may already be at between 30 and 60. In addition to the regular tests, the Quality Control department performs additional statistical tests at the time of shipment. In this case the packing may show signs of having been opened, and the accumulated lamp operating hours may be slightly higher than the hours associated with the standard tests. DLP and DMD are registered trademarks of Texas Instruments. DCDi is a registered trademark of Faroudja, a division of Genesis Microchip, Inc. DigiOptic is a registered trademark of SIM 2 HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC 2 2 IMPORTANT SAFETY INSTRUCTIONS ATTENTION: To reduce the risk of electric shock, disconnect the power supply cable on the rear panel before removing the top cover of the Display. Refer to trained, authorised personnel for technical assistance. This symbol indicates the possible electric shock hazard associated with uninsulated live components in the interior of the unit. CAUTION RISK OF ELECTRIC SHOCK! DO NOT REMOVE THE TOP COVER ! This symbol indicates the presence of important instructions regarding use and maintenance of the product. The RTX system consists of two parts connected by a fibre optic cable: the DigiOpticTM Image Processor and the Display. In this manual references to the "unit" refer to one of the two units that make up the system. Prior to switching on the Display please read each chapter of this manual carefully as this manual provides basic instructions for using the Display. The installation of the lamp assembly, preliminary adjustments and procedures that necessitate the removal of the top cover, must be carried out by authorised, trained technicians. There are no user serviceable parts inside. To ensure safe and long term reliability please use power cables supplied with the Display. Observe all warnings and cautions. CLASS 1 LASER PRODUCT This product complies with fda radiation performance standards, 21 cfr chapter 1 subchapter j. This product complies with european standard en 60825. This product is classified as a class 1 laser product and there is no hazardous radiation with the safety protection. Danger! Invisible laser radiation when open. avoid direct exposure to beam. Do not open the covers of the product and never touch the internal parts in order to avoid exposure to visible or invisible laser radiation. · Federal Communication Commission (FCC Statement) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is used in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determinated by turning the equipment off and on, the user is encuraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/Tv technician for help. · For customers in Canada This Class B digital apparatus complies with Canadian ICES-003. · For customers in the United Kingdom ATTENTION: This apparatus must be earthed The wires in this mains lead are coloured in accordance with the following code: Green-and-Yellow: Earth Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. 3 · Read this manual carefully and keep it in a safe place for future consultation. This manual contains important information on how to install and use this equipment correctly. Before using the equipment, read the safety prescriptions and instructions carefully. Keep the manual for future consultation. · Do not touch internal parts of the units. The units contain electrical parts carrying high voltages and operating at high temperatures. Do not remove the cover from the units, refer to qualified service personnel for all repair and maintenance requirements. The warranty will be automatically invalidated if the cover is removed from the units. · Power supply disconnect device. The device for disconnecting the units from the mains power supply is constituted by the power cable plug. Ensure that the power cable plugs and the electrical mains socket outlets are easily accessible during installation operations. To disconnect the units from the electric power supply, pull the plug to remove it from the socket outlet. Do not pull the power cable. · Use only the specified type of mains power supply. Connect the units to a mains electrical supply with rated voltage of between 100-240 VAC, 50/60 Hz and equipped with a protective earth connection. If you are unsure of the type of mains power supply in your home, consult a qualified electrician. Ensure that the power draw of the units is commensurate with the rating of the electrical socket outlets and any extension cables that are used. For the DigiOpticTM Image Processor use exclusively the power supply unit provided or an alternative power supply unit expressly approved by SIM2. · Beware of power supply cables. Position the power supply cables so that they do not constitute an obstruction. Position the power supply cables where they cannot be reached by children. Install the units as close as possible to the wall electrical socket outlet. Do not tread on the power cables, make sure that they are not tangled or pulled; do not expose the power cables to heat sources; make sure that the power cables do not become knotted or kinked. If the power cables become damaged, stop using the system and request the assistance of an authorised technician. · Disconnect the apparatus from the mains power supply in the event of electrical storms and when not in use. To avoid damage that could be caused by lightning striking in the vicinity of your home, disconnect the units in the event of electrical storms or when the system will remain unused for prolonged periods. · Avoid contact with liquids and exposure to humidity. Do not use the units near water (sinks, tanks, etc.); do not place objects containing liquids on top of or near the units and do not expose them to rain, humidity, dripping water or spray; do not use water or liquid detergents to clean the units. · Prevent the units from overheating. Do not obstruct ventilation openings. Do not place the units near heat sources such as heaters, radiators or other devices that generate heat (including amplifiers). Do not position the units in confined, poorly ventilated places (bookcase, shelves, etc.). · Do not expose the eyes to the intense light emitted by the lamp. Never look directly at the lamp through the ventilation opening when the unit is switched on. Risk of eyesight impairment. Ensure also that children do not look directly at the lamp. · Position the unit on a stable surface. To avoid serious injury to persons and damage to property, make sure the units are placed on a level, flat and stable surface from which they cannot fall, tip over or slide. Pay special attention if the units are placed on a trolley so that they can be moved around. Ensure that the units are not subjected to impact. · Do not insert objects through the units' openings. Make sure that no objects are inserted inside the units. If this should occur, disconnect the unit from the power supply immediately and call an authorised technician. 4 3 INSTALLATION CONNECTING THE TWO UNITS SIM2's RTX system is made up of the following components (Fig.1): · Display · DigiOpticTM Image Processor · remote control · DigiOpticTM Image Processor power supply unit · three power cables for the Display · three power cables for the DigiOpticTM Image Processor · triple fibre optic cable for linking the DigiOpticTM Image Processor and the Display · one cable HDMITM-HDMITM · one cable HDMITM-DVI · two brackets for mounting the DigiOpticTM Image Processor to the rack. · four 1.5 V AAA-type batteries for the remote control · User and installation manual If any acce ...