User manual SIMA UDC-2

Safety and Maintenance DO NOT use charger inside a drawer, closed cabinet, on a carpet or cover with a cloth. The charger will become slightly warm in normal use, but if contained, heat may damage the charger and battery pack. DO NOT atttempt to open the charger, there are no serviceable parts. Doing so will void the warranty. DO NOT allow moisture of any kind to come in contact with the charger. NEVER IMMERSE IN LIQUID! DO NOT store where it may be exposed to extreme temperatures; avoid placing in direct sunlight. High temperatures can shorten the life of electronic devices, damage batteries and warp metal or plastics. DO NOT short circuit the output terminal or contacts. DO NOT drop the unit, a jolt can cause permanent damage and is not covered by the warranty If the charger must be cleaned, be sure it is unplugged. Wipe the unit with a clean cloth, lightly dampened with mild detergent. Use a clean cloth, lightly dampened with rubbing alcohol to clean the metal contacts. If you have trouble installing your battery or if it is not listed on this chart, do not call the store where you purchased the UDC-2. Call Sima customer service at 800-345-7462 Battery Chart Brand Canon Canon Canon Canon Hitachi Hitachi Hitachi JVC JVC JVC Panasonic Panasonic Panasonic RCA RCA Sharp Samsung Samsung SONY SONY SONY SONY SONY Universal Battery Charger for use with Camcorders Model UDC-2 Tray Base A C C Base A C Base Base A A Base A C C C Base A Base C C Base A A A A A Volt 6V 7.2V 7.2V 7.2V 6V 7.2V 7.2V 6V 7.2V 7.2V 6V 7.2V 7.2V 6V 7.2V 6V 7.2V 7.2V 6V 7.2V 7.2V 7.2V 7.2V Batt. type NiCad/NiMH Lithium Ion Lithium Ion Lithium Ion NiCad/NiMH Lithium Ion Lithium Ion NiCad/NiMH Lithium Ion Lithium Ion NiCad/NiMH Lithium Ion Lithium Ion NiCad/NiMH Lithium Ion NiCad/NiMH Lithium Ion Lithium Ion NiCad/NiMH Lithium Ion Lithium Ion Lithium Ion Lithium Ion Model Number BP-E77/711/714/718/722/729 BP-80/85 BP-608/617 BP-911/914/915/924/927/930/941/945 VM-BP82/82A/83/84/84A VM-BPL13A/27A/30A/60A DZ-BP16/28 BN-V11U/12U/14U/140U/22U/50U/60U BN-V20U/25U BN-V607/615U BN-V812/814U PV-BP15/17/18/ VW-VBS1E/S2E VW-VBD1/PV-BP5/AG-BP25 CGR-D120/220/320/S602/ PV-BP8A/VW-VBD20 CGA_DU07/14/21 BB-45/75L/060/120/FB120/1260 BB-55L/65L/85L BT-80 SB-L110/220 SB-L160/320/480 NP-55/66/67/68/77/78/98 NP-FF50/70 NP-F100/200/300 NP-F330/530/550/730/730H/750/750 SP/930/950/960 NP-FM30/50/70/90/91/QM50/70/90 Works with these camcorders: Sony JVC RCA Canon Sharp Hitachi & more! www.simacorp.com 800-345-7462 Trouble Shooting Problem Possible Cause/Solution Confirm the AC or cigarette adapter is firmly No Indicator connected at both ends. Confirm that wall outlet is Lightswith battery mounted working. Check fuse in car cord (un-screw tip of cigarette lighter adapter). · Battery is already fully charged. · Battery mounted incorrectly; remove and re-mount battery. Clean battery/charger contacts. Hissing noise in Normal operation due to advanced switching Charging Mode circuitry. Includes 3 adapter trays to charge Lithium - ion, Ni-Cad and NIMH batteries Includes AC & DC adapters Warranty Statement Sima Products Corporation ("Company") warrants that if this product proves to be defective to the original purchaser in material or workmanship within 90 days from the date of original retail purchase, the company will, at the company's option, either repair or replace same without charge (but no cash refund will be made). To enforce this warranty, ship your unit, freight pre-paid, including reasonable proof of date and place of purchase and description of problem to: Attn: Customer Service c/o Sima Products Corporation 140 Pennsylvania Ave. Bldg #5 Oakmont, PA 15139 Exclusions: This Limited Warranty covers all defects in material and workmanship in the product, except damage resulting from accident, misuse, abuse, attempted repair by anyone other than the Company, neglect or from their normal and ordinary use of the product. The Company accepts no liabilities or obligations for consequential or incidental damage arising out of or in connection with the use or performance of the product. The Limited Warranty provides you with specific legal rights, you may have additional legal rights provided to you under the laws of your state or federal laws. ©2004 Sima Products Corporation 140 Pennsylvania Ave. Bldg #5 Oakmont, PA 15139 800-345-7462 Fax 412-828-9338 www.simacorp.com PN217001 Introduction Congratulations on buying the Sima UDC-2, a universal battery charger for use with digital camera batteries. Using the AC or DC adapters included, you can quickly and easily charge your Nicad, NiMH or lithium ion camcorder batteries at home or in the car. This package includes: UDC base unit, TrayA, Tray C & Tray 2, 120V AC adapter, 12V DC car adapter and this instruction manual. How to Connect 120V AC Power Supply Connect the AC adapter plug to To 120V AC outlet the Power Input jack on the rear of the UDC base. Plug the AC adapter into any standard 120V AC household outlet. ( See Power Input jack diagram at right.) The green Full indicator light will blink once. Mounting the Batteries To install the battery - Typically, you can install the battery onto the charger plate the same way you install the battery onto your camcorder. Align the contacts on your battery with the appropriate contacts on the charger. Follow the guides on the battery and the charger. The battery should slide easily into place. If it does not, do not force the battery into place. Realign the guides and try again.The UDC-2 will automatically detect the battery type and voltage from the tray. Features j Precision end-of-charge detection assures a full charge j "Top-off" function trickle charges to maintain a full charge. j LED indicator displays charger mode. j Defective battery dectection. j Overcharge protection. Technical Specs Input: Standby Current: Charge Current: Charge Termination: Size & Weight 12V DC 30mA 800mA @ constant current mode Fixed voltage Lithium (4.2V for 3.6V, 8.4V for 7.2V) NiCad/NiMH (delta V) 5.25" x 2.75" 3.1 oz. How to Connect 12V DC Car Power Supply Connect the 12V DC car cord plug Power Input jack to the power input jack on the rear of the UDC base. Plug the cigarette To car cigarette lighter lighter adapter into the cigarette lighter socket of the vehicle. (See diagram at right.) The green Full indicator light will blink once. Mounting the Adapter Plates Some battery models will require the use of an adapter plate (AA/AAA, 1 or 2). Consult the battery chart in this manual to determine which adapter plate your camera or camcorder battery requires. Charging the Battery As soon as the battery is properly mounted, charging begins as indicated by the steady red light on the Charge Status indicator.(Fig. 1 below) When charging is complete, the green Full Status indicator will turn on (fig. 2). At this point, the battery can be removed for use. Removing the battery at this point will not harm it. It is recommended that you leave the battery connected tot he charger for another 30 minutes to ensure a full or "topped off" charge SLIDE INSERT TO LOCK Base Unit and Trays MODEL : UDC UNIVERSAL DIGITAL CHARGER For Hitachi 6 volt To install the adapter trays Step 1. Place the adapter tray onto the base unit. For Canon 6 volt 1 Step 2. Align the arrow on the tray to the INSERT dot on the base unit. + + Charge Full Discharge Charge Full Discharge Charge Full Discharge 2 Plate C Plate A 1 2 3 4 5 Plate 2 INSERT SLIDE TO LOCK 3 Fig. 1 Fig. 2 Fig. 3 Press to discharge Discharging the Battery Step 3. Slide the tray to the right. It will snap firmly in place. To remove the tray, slide it to the left. To maximize the full power of your NiCad and NiMH batteries, we recommend discharging before recharging. To discharge, mount the battery on the tray and press the Discharge button. (Fig. 3 above). The yellow Discharge Status indicator will turn on. When discharging is complete, the battery will automatically begin to recharge and the red Charge Status indicator will turn on (Fig. 1). Depending on the amount of charge left in the battery, this may take several hours. Note: Lith-ion batteries do not require discharging. 1. Base Unit 4. Full Indicator 2. Charge Status indicator 5. Discharge status light 3. Discharge button