27 & 28 INSTRUCTIONS FOR USING SINGER* SEWING MACHINE NO. 27 & 28 VIBRATING SHUTTLE, FOR FAMILY USE When requiring Needle, Oil, Parts or Repairs, for your Machine Look for the Red "S" There are Singer Shops in every City THE SINGER MANUFACTURING CO. 27 & 28 The Table of Contents Warning To all whom it may concern Singer Service It's sew easy by electricity The Hand Attachment Stop Motion To Operate the Hand Machine To Ensure Perfect Action of the Machine To Set the Needle To Thread the Needle To Wind the Bobbin To Remove the Shuttle To Thread the Shuttle To Replace the Shuttle To Prepare for Sewing To Commence Sewing To Remove the Work To Regulate the Tension To Alter the Length of Stitch To Change the Pressure on Material To Turn a Corner To Sew Flannel or Bias Seams To Oil Machine Hints Needles Breaking Thread Breaking Skipping Stitches Stitches Looping Material Puckering Instructions for Using Attachments Bias Gauge The Binder - Binding To Bind with Dress Braid To Make French Folds The Adjustment and Operation of the Binder Binding Outside Curves Binding Inside Curves The Quilter The Foot Hemmer - Hemming Hemming and Sewing on Lace in One Operation The Foot Hemmer - Felling The Adjustable Hemmer The Adjsutable Hemmer - Wide Hemming The Under Braider - Braiding 27 & 28 WARNING It is essential that your machine should be kept well oiled, in accordance with the instructions given on pages 13 and 14 of this book. To all whom it may concern: The improper placing or renewal of the trademark "SINGER" or any other of the trademarks of The Singer Manufacturing Company (all of which are duly Registered Trademarks) on any machine that has been repaired, rebuilt, reconditioned, or altered in SINGER Oil, which is specially prepared for any way whatsoever outside a SINGER factosewing machines, is supplied in tins which have the well-known SINGER Red "S" printed ry or an authorised SINGER agency is forbidden. thereon. SINGER Needles are stamped with the Trade Mark SIMANCO* and are sold in green packets which also bear the SINGER Red Letter "S." Needles in Containers marked " For Singer Machines " are not SINGER made needles. Should your machine require overhauling or repair, apply only to a SINGER SEWING CENTRE or SINGER Salesman, otherwise you will risk its being irretrievably damaged. Every description of sewing machine repaired, SINGER SERVICE Now that you have purchased your new SINGER Sewing Machine we do not want you to feel that your relations with us have come to an end. The following instructions are worded so that they may be easily understood by everyone, and we would suggest that you study them carefully in order that you may obtain the fullest use and pleasure from your sewing machine. If, however, you require further assistance we would ask you to call at the local SINGER SEWING CENTRE where advice will always be willingly given in the use of any SINGER Machine and its Attachments. We hope, too, that you will make the SINGER SEWING CENTRE your headquarters for sewing supplies and service. Only there, or through SINGER authorized representatives, can you secure SINGER oil, cotton, needles, etc. all of which are so important in obtaining 3 27 & 28 4 27 & 28 The Hand Attachment FIG. 1 FIG. 2 When the cover is removed from the machine, the hand attachment will be found to be out of working position, as shown in Fig. 1. To operate the machine, pull the small spring stud (2, Fig. 1) and turn the handle back until the lever (1, Fig. 1) enters the socket (3, Fig. 1); also see that the hinged finger (4, Fig. 2) is turned back between the spokes of the wheel. The machine will then be ready for working, as shown in Fig. 2. Before replacing the cover, the lever should be disengaged, and the handle placed in the position shown in Fig. 1. 5 27 & 28 Stop Motion This device a allows the hand wheel to run free, so that bobbins may be wound without operating the mechanism. To loosen the wheel hold it with the left hand and with the right hand turn the stop motion screw over towards you, as shown in Fig. 3. To Operate the Hand Machine Tighten the hand wheel (see Fig. 3) and place a piece of material under the presser foot (7, Fig. 5). Then lower the latter by means of the lifter (3, Fig. 5). Now turn the handle over from you to work the machine, without its being threaded, until you are accustomed to guiding the material with the left hand. FIG. 3 6 27 & 28 To Ensure Perfect Action of the Machine The hand wheel must always turn over towards you. Do not work the machine with the presser foot lowered or with the shuttle and the needle threaded, except when sewing Both slides over the shuttle must be kept closed. To Set the Needle (See Fig. 4) Raise the needle bar to its highest point and loosen the thumb screw. (A). Hold the needle with the left hand and, with its flat side to the right, insert it into the needle clamp (B) as far as it will go. Then retighten the thumb screw. Fig. 4. Positioning Needle in Needle Clamp. 7 27 & 28 To Thread the Needle (See Fig. 5) Turn the hand wheel heel until the lever (2) is at its highest. Place a reel of thread on the spool pin and pass the thread through the notch (13) down, and from right to left under and between the tension discs (12), and up through the eyelet in the take-up spring (4). Then pass the thread from the front through the hole in the lever (2), down through the guard (5), into the guide (6), and from left to right through the eye of the needle. Draw about three inches of thread through the eye of the needle with which to commence sewing. To obtain best results it is absolutely necessary that the needle used be of the size stated for the number of cotton, linen or silk, as shown on inside of back cover. If rough or uneven thread is used, or if it passes with difficulty through the eye of the needle, the machine will not function satisfactorily. The SINGER Needle Threader saves time, trouble and patience, and is invaluable to those having defective sight. FIG. 5 8 27 & 28 To Wind the Bobbin (See Fig. 6) Loosen the hand wheel (see Fig. 3) and push the top of the winder from you until its rubber ring (5) just touches the ledge of the hand wheel. Turn the latter over towards you until the thread guide (2) moves to the extreme right. Place a reel of thread on the spool pin; and pass the end of thread through the notch at top of the face plate (13, Fig. 5); then thread the winder by passing the thread upward through the eyelet (1) and into the notch (2). Draw the knob (3) to the left, and place an empty bobbin between the cup at the right (4) and the centre hole at the left. Now clamp the end of thread between the cup and the end of the bobbin, turn the hand wheel towards you and wind by operating the machine as when sewing. When nearly full remove the bobbin by pulling the knob (3) to the left, then withdraw the winder from the ledge of the hand wheel and tighten the latter by turning the stop motion screw from you. FIG. 6 9 27 & 28 To Remove the Shuttle Open the front slide of the machine and turn the hand wheel towards you until the shuttle comes full under the opening. Press down the point of the shuttle with the thumb and lift out. Turn the open end of the shuttle downward and the bobbin will drop out. NOTE: The shuttle should not be lifted out by the spring. To Thread the Shuttle Hold the shuttle, as in Fig. 7, and insert the bobbin so that the end of the thread draws from the left towards the right, as shown in the illustration. FIG. 7 10 27 & 28 To Thread the Shuttle Continued... Place the forefinger of the left hand on the end of the bobbin, and draw the thread down into the slot of the shuttle, towards the point, as far as it will go (see Fig. 8); then pull the thread tightly upwards and down again, so that it lies across the point in the centre of the spring, as shown in Fig. 9. FIG. 8 FIG. 8 11 27 & 28 To Replace the Shuttle.. After threading, take the shuttle in the right hand with its point towards you, and place it in the shuttle carrier, as shown in Fig. 10, leaving a loose end of thread about three inches long above the slide. Then close the latter. NOTE: Keep the inside of the shuttle and under the tension spring (see Fig. 7) free from accumulation of lint or dust. FIG. 10 12 27 & 28 To Prepare for Sewing With the left hand hold the end of the needle thread, leaving it slack from the hand to the needle. Turn the hand wheel over towards you for the needle to move down and up again to its highest. Pull the thread you are holding, and the under thread will be brought up with it through the hole in the throat plate, as shown in Fig. 11. Place both ends of thread under and to the back of the presser foot. To Commence Sewing Place the material to be sewn beneath the presser foot, lower the latter, and commence to sew by turning the hand wheel over towards you. FIG. 11 To Remove the Work NOTE: Do not try to help the feeding of the work by pulling the material, as Raise the needle bar to its highest, lift the presser foot (7, Fig. 5), at the same time pressing the this may deflect the needle and tension release (10, Fig. 5) with the thumb of the cause it to break. The machine right hand. Move the material back and to the feeds without any assistance. left, and sever the threads by passing them over the thread cutter above the presser foot. Leave a few inches of thread under and at the back of the presser foot. 13 27 & 28 To Regulate the Tensions Correct Stitch. For ordinary stitching, the tension on the upper and under threads should be equal, so as to lock both threads in the centre of the work, as above. If either tension is stronger than the other, imperfect stitching will be the result, thus: Needle Thread Tension too strong. FIG. 12 Needle Thread Tension too weak. Lower the presser foot and turn the thumb nut in the direction illustrated by the arrow to increase the tension or in the opposite direction to lessen it. As all machines are correctly adjusted before leaving the factory, the under tension seldom requires to be altered, but if this becomes necessary tighten the screw near the point of the shuttle (see Fig. 7) to increase the tension, or loosen it slightly to lessen the tension. Always use thread with corresponding size of needle as per Table on page 3 of cover. Fine fabrics require a light tension, while heavy materials want more tension to obtain a perfect stitch. The tension on the needle thread should be regulated only when the presser foot is down. A correct stitch can usually be obtained by varying the tension on the needle thread (see Fig. 12). 14 27 & 28 To Alter the Length of Stitch Turn the thumb screw inwards (see Fig. 13) to lengthen the stitch, or turn outwards to shorten it. To Change the Pressure on Material For ordinary family sewing it is seldom necessary to change the pressure on the material. If sewing fine silk or flimsy material, lighten the pressure by giving the thumb screw (1, Fig. 5) two or three turns upwards. To increase the pressure, give the thumb screw a few turns downwards. To Turn a Corner Stop the machine when the needle is rising, but still in the material. Raise the presser foot and turn the work, using the needle as a pivot. Then lower the presser foot. To Sew Flannel or Bias Seams Use a short stitch and as light a tension as possible on the needle thread, so that the stitching will be loose enough to allow the material to stretch. FIG. 13 15 27 & 28 To Oil the Machine FIG. 14 To ensure easy running the machine requires to be oiled so that all moving parts in contact are covered with a film of oil. These should never be allowed to become dry. If used constantly, the machine should be oiled daily, while with moderate use, an occasional oiling is sufficient. A drop of oil applied at the points indicated by arrows in Figs. 14 and 15 is sufficient. The small plate in front of the machine and the larger plate at the back should both be turned up and oil applied to the parts exposed. It is important that oil be applied to point "A," Fig. 14, when the take-up lever (2, Fig. 5) is at its lowest, and a little oil rubbed over the surface of the shuttle race. There are also two holes in the hand attachment to which oil should be applied occasionally. When oiling, insert the oil can spout well into the holes. 16 27 & 28 To Oil the Machine continued... FIG. 15 After oiling, run the machine rapidly for a few minutes so that the oil may reach the bearings. Neglect to oil the machine will shorten its life and cause you trouble and annoyance. Always use SINGER oil. Inferior oil clogs the bearings, prevents efficient working, and causes rapid wear of the mechanism. 17 27 & 28 HINTS. Needles Breaking. See that the needle is not bent, the upper tension is not too tight, and the presser foot or attachments are securely fastened. Avoid pulling the material and do not sew heavy seams or thick goods with too fine a needle ( ...