User manual SMC SMC2635W

EZ Connect 2.4GHz 11 Mbps Wireless Cardbus Adapter User Guide The easy way to make all your network connections 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 February 2004 Revision number: E022004 R01. F1.0 Copyright Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2004 by SMC Networks, Inc. 38 Tesla Irvine, CA 92618 All rights reserved. Trademarks: SMC is a registered trademark; and EZ Connect is a trademark of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders. COMPLIANCES Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: · Reorient or relocate the receiving antenna · Increase the separation between the equipment and receiver · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected · Consult the dealer or an experienced radio/TV technician for help FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. i Industry Canada - Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled "Digital Apparatus," ICES-003 of Industry Canada. Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matérial brouilleur: "Appareils Numériques," NMB-003 édictée par l'Industrie. EC Conformance Declaration - Class B SMC contact for these products in Europe is: SMC Networks Europe, Edificio Conata II, Calle Fructuós Gelabert 6-8, 2o, 4a, 08970 - Sant Joan Despí, Barcelona, Spain. This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/ EEC. For the evaluation of the compliance with these Directives, the following standards were applied: RFI Emission: · Limit class B according to EN 55022:1998, IEC 60601-1-2 (EMC, medical) · Limit class B for harmonic current emission according to EN 61000-3-2/1995 · Limitation of voltage fluctuation and flicker in low-voltage supply system according to EN 61000-3-3/1995 Immunity: · Product family standard according to EN 55024:1998 · Electrostatic Discharge according to EN 61000-4-2:1995 (Contact Discharge: ±4 kV, Air Discharge: ±8 kV) · Radio-frequency electromagnetic field according to EN 61000-4-3:1996 (80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m) · Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC power supply: ±1 kV, Data/Signal lines: ±0.5 kV) · Surge immunity test according to EN 61000-4-5:1995 (AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV) ii · Immunity to conducted disturbances, Induced by radio-frequency fields: EN 61000-4-6:1996 (0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3 V/m) · Power frequency magnetic field immunity test according to EN 61000-4-8:1993 (1 A/m at frequency 50 Hz) · Voltage dips, short interruptions and voltage variations immunity test according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30% Reduction @500 ms, >95% Reduction @5000 ms) LVD: MDD: · EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997) · IEC 60601-1 iii iv TABLE OF CONTENTS EZ ConnectTM Wireless Cardbus Adapter . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Driver and Utility Installation . . . . . . . . . . . . . . . . . . . . . 6 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Utility Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 The Wireless Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Link information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 IP Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Site Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Version Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Network Configuration and Planning . . . . . . . . . . . . . 21 Network Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ad Hoc Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Infrastructure Wireless LAN . . . . . . . . . . . . . . . . . . . . . . 22 Setting the Communication Domain . . . . . . . . . . . . . . . . . . . . . 23 Stationary Wireless PCs . . . . . . . . . . . . . . . . . . . . . . . . . 23 Roaming Wireless PCs . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Adapter Installation Problems . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Network Connection Problems . . . . . . . . . . . . . . . . . . . . . . . . . 25 SMC Networks 802.11b Wireless Product Max. Distance Table . . 26 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Software Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 v TABLE OF CONTENTS vi EZ CONNECTTM WIRELESS CARDBUS ADAPTER SMC's EZ Connect Wireless Cardbus Adapter (SMC2635W) is an 11 Mbps wireless network adapter that seamlessly integrates with existing Ethernet networks to support applications such as mobile users or temporary conferences. This solution offers a high data rate and reliable wireless connectivity with considerable cost savings over wired LANs (which include long-term maintenance overhead for cabling). Just install enough wireless access points to cover your network area, plug wireless cards into your notebooks, and start networking. Using this card in conjunction with SMC 11b/11g wireless access points, you can create an instant network that integrates seamlessly with Ethernet LANs. Moreover, moving or expanding your network is as easy as moving or installing additional access points ­ no wires! Features · · · · Up to 11 Mbps data rate Wireless connection without the hassles and cost of cabling Greater flexibility to locate or move networked PCs Integrates with or replaces wired LANs at dramatically lower cost than wired alternatives 1 APPLICATIONS · · · · · Seamless connectivity to wired Ethernet LANs augments existing networks quickly and easily Direct Sequence Spread-Spectrum (DSSS) technology provides robust wireless connection Supports a wide range of systems User-friendly configuration interface Enhances your network security with 64/128-bit WEP encryption Applications EZ Connect wireless products offer fast, reliable, cost-effective network access for wireless clients in applications such as: · Remote access to corporate network information Email, file transfer, and terminal emulation Difficult-to-wire environments Historic or old buildings, asbestos installations, and open areas where wiring is difficult to employ Access to databases for mobile workers Doctors, nurses, retailers, office workers who need access to databases while being mobile in a hospital, retail store, office, campus etc. Temporary LANs for special projects or peak times Trade shows, exhibitions, and construction sites that need to set up for a short time period. Retailers, airline, and shipping companies who need additional workstations for peak periods. Auditors who require workgroups at customer sites · · · 2 SYSTEM REQUIREMENTS · Frequently changing environments Retailers, manufacturers, and banks who frequently rearrange the workplace and change location SOHO users SOHO (Small Office Home Office) users who need quick and easy installation of a small computer network · System Requirements Before you install the EZ Connect Wireless Cardbus Adapter, check your system for the following requirements: · · · A laptop with a CardBus slot A minimum of 1.5 Mbytes of free disk space for installing the driver and utility program Another IEEE 802.11b compliant device installed in your network, such as a Barricade SMC7004VWBR Wireless Broadband Router, or another PC with an SMC2662W Wireless USB Adapter 3 PACKAGE CHECKLIST Package Checklist The EZ Connect Wireless Cardbus Adapter package includes: · · · One SMC2635W Wireless Cardbus Adapter One EZ Installation Wizard & Documentation CD One Quick installation guide Please register this product and upgrade the product warranty at www.smc.com Please inform your dealer if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use them again to repack the product if there is a need to return the product. 4 HARDWARE DESCRIPTION The EZ Connect Wireless Cardbus Adapter provides 11 Mbps connections. It is fully compliant with the specifications of the IEEE 802.11b standard. The adapter can be installed in any notebook with a CardBus type II or type III slot. LED Indicator The EZ Connect Wireless Cardbus Adapter includes one status LED indicator, as described in the following figure and table. Link/Act LED Link/Act Status On Green Flashing Description The adapter is associated to the Wireless LAN. The adapter is transmitting/receiving data. 5 DRIVER AND UTILITY INSTALLATION DRIVER AND UTILITY INSTALLATION The installation CD that comes with the package contains all the software available for the EZ Connect Wireless Cardbus Adapter. Any new or updated drivers can be downloaded from SMC's web site at: http://www.smc.com You may find that the instructions here do not exactly match your version of Windows. This is because these steps and screen shots were created from Windows XP. Windows 98, Windows Millennium Edition, and Windows 2000 are similar, but not identical, to Windows XP. Notes: 1.For Windows 98 users, installation processes may require the use of your original copy of Windows OS. Please prepare the Windows OS CD before proceeding with the installation. 2. It is recommended that you install the utility and driver software first, before inserting the adapter into your laptop. 6 DRIVER AND UTILITY INSTALLATION 1. Insert the CD into the CD-ROM drive and the program will auto-run. The InstallShield Wizard window will appear. 7 DRIVER AND UTILITY INSTALLATION 2. There are three options to install the software. Select Easy for hassle-free installation. For users who wish to use WindowsXP Wireless Zero Configuration to manage the adapter, select the "Use the WindowsXP Wireless Network Connection Utility" option. 3. The system will start installing files, and this process may take a few minutes. This message will then appear prompting you to insert the adapter into your laptop. 8 DRIVER AND UTILITY INSTALLATION 4. When you insert the adapter into the laptop, the system will detect the card automatically. Then the Found New Hardware window will appear. Select Install the software automatically, and click Next. 5. For users who are using this adapter outside of the United States and Canada, the Country Select window will appear. Please select the country at which you are using the adapter. Note: This domain configuration applies only to users outside of the FCC regulatory domain. If you are using this adapter in the United States and Canada, please skip this step. 9 DRIVER AND UTILITY INSTALLATION 6. This window will then appear indicating the driver has been installed into your system. Click Finish to complete the installation. Your adapter is now ready for use. 10 HARDWARE INSTALLATION Network cards are sensitive to static electricity. To protect the card, avoid touching the connctor, and always touch the ground often to equalize the static charges before handling the card. To plug the card: 1. Find an available Type II CardBus slot in your computer. 2. With the CardBus's 68-pin connector facing the Cardbus slot and the "EZ Connect Wireless Cardbus Adapter" label facing up, slide the card completely into the slot as shown below. Note: Install the driver and utility software first before inserting the adapter into your laptop. 11 UTILITY CONFIGURATION UTILITY CONFIGURATION The Wireless Utility To communicate with other 802.11b or 802.11g devices, you need to configure the SMC2635W adapter first. Double-click the icon on the desktop to launch the configuration utility, or you can access it from the Start menu. Note that the screen shots were taken from Windows XP and will not look exactly the same in all operating systems. The functions, however, are the same. The configuration utility includes the following 5 tabs: Configuration ­ Allows you to set parameters for the adapter. Link Information ­ Allows you to view network status. IP Information ­ Displays TCP/IP data. Site Survey ­ Scans/Shows all wireless devices within the adapter's signal range. Version Information ­ Shows the driver and utility version information. At the bottom of each screen, there are two boxes that can be selected: · · Radio On/Radio Off ­ This allows you to turn on/off the transmission/reception of the Cardbus. Help ­ Click here to display the help file. 12 THE WIRELESS UTILITY Configuration Go to the Configuration tab to set parameters for the SMC2635W adapter. Select Profile ­ You can specify a profile name for a specific configuration of parameters. New ­ To set up a new profile, click New. Save ­ To save a new profile after configuring the settings, click Save. Delete ­ To delete a profile, select the profile from the drop-down menu in the Select Profile field, then click Delete. SSID ­ Input an SSID for the wireless network to which you want to connect. To roam among multiple access points, set the SSID to ANY to allow connection to any access point within the signal range. (Default setting: ANY) 13 THE WIRELESS UTILITY Channel ­ If you are setting up an ad hoc wireless network, set the channel number to the same radio channel as that used by the other wireless clients in your group. However, if you are connecting to a network via an access point, then the channel is automatically set by the access point to the channel that it uses. (See" Network Topologies" on page 20.) You only need to manually set the channel when the Operating Mode is 802.11 AdHoc. Note: The available channel settings are limited by local regulations which determine the number of channels that are available. Transmit Rate ­ Indicates the data transmission rate. Select an appropriate transmission speed. Lower speeds will give better range. (Default: Auto) Operating Mode ­ Set the adapter's operating mode to 802.11 AdHoc for a network environment that does not have an access point, or to Infrastructure for connections with an access point. Tx Power ­ Move the slider up and down in the Tx Power field to increase or reduce the transmission power. Encryption ­ To enable the Wired Equivalent Privacy (WEP) function, set this to 128-bit or 64-bit. The WEP implemented in SMC's EZ Connect Wireless Cardbus Adapter is based on the RC4 encryption algorithm. The encryption keys are provided to ensure data confidentiality. WEP security protects your wireless LAN against eavesdropping and unauthorized access by intruders. If WEP is in use, all clients on the same network must use the same WEP key settings in order to communicate with each other. 14 THE WIRELESS UTILITY Key Type ­ Select Hex or ASCII. Default Key ­ Choose one Key for encryption. Passphrase ­ Check this box to auto-generate keys for encryption. First, check this box, then enter a string of characters into the space. Encryption keys will be generated automatically. When encryption is set to 128-bit, only Key 1 will be generated. If encryption is set to 64-bit, 4 Keys will be generated. Note that you must use the same Passphrase and Default Key on all the other clients in your network. Note: A passphrase string can consist of up to 32 alphanumeric characters. How to set up WEP To set up the WEP function, take the following steps: 1. Select 128-bit or 64-bit in the Encryption field. 2. To automatically generate keys, check the Passphrase box, and type in a string of characters in this field. 3. In the Default Key field, select one key as the default key that you want to use for encryption. 4. Click Apply changes to allow the settings to take effect. 15 THE WIRELESS UTILITY Or 1. Select 128-bit or 64-bit in the Encryption field. 2. In the Key Type field, select ASCII or Hex. 3. In the Default Key field, select one key as the default key that you want to use for encryption. 4. Manually type in a string of characters in the corresponding Key number field that you selected in step 3. 5. Click Apply changes to allow the settings to take effect. Note: When setting up WEP without using the Passphrase function, if the Key Type is set to Hex, only hexadecimal characters (range: 0~9 and A~F) can be used. When Encryption is set to 64-bit, a maximum of 10 Hex characters can be entered in the Key field. When Encryption is set to 128-bit, a maximum of 26 Hex characters can be used. If the Key Type is set to ASCII, and Encryption is set to 64-bit, then 5 ASCII digits can be used in the Key field. For 128-bit Encryption, 13 ASCII characters can be used. 16 THE WIRELESS UTILITY Link information The Link information screen displays information on the current wireless network to which you are connected. Associated BSS ID ­ The MAC address of the access point to which the Cardbus is connected in an infrastructure network. In an ad hoc network, the BSS ID is a random number generated by the first station that communicates with other stations in the network. The BSS ID of the other stations will then be set to the same value. Channel ­ The channel used to connect with the wireless device. Current Tx Rate ­ The data transmission rate. SSID ­ The service set identification for the wireless network that the Cardbus is connected to. Rx Fragments ­ The number of received fragments. 17 THE WIRELESS UTILITY Tx Fragments ­ The number of transmitted fragments. Link Quality ­ Shows the link quality of the wireless connection. Signal Strength ­ Shows the strength of the connection between the adapter and the access point. IP Information This screen displays IP information for your laptop. Now that you have configured your Wireless Cardbus Adapter to connect to wireless networks, your adapter needs to obtain new network settings. By releasing old IP settings and renewing them with settings from the access point, you will also verify that you have configured your adapter correctly. To release current IP settings click on Release, then click on Renew to renew the settings. 18 THE WIRELESS UTILITY IP Address ­ Internet address of the notebook. IP Netmask ­ A mask used to determine what subnet an IP address belongs to. Host Name ­ The computer's name on the network. Gateway ­ The IP address of the network gateway. Site Survey Site Survey scans and displays all wireless devices within range. You can choose one of them to connect to by double-clicking on an entry. SSID -- Service Set ID. See "Configuration" on page 13 for details. BSSID -- Basic Service Set ID. See "Link information" on page 16 for details. 19 THE WIRELESS UTILITY Channel -- The radio channel on which the access point operates. See" Link information" on page 16 for details. Encryption -- The key icon indicates that WEP function has been enabled. Signal -- This shows the signal strength from the adapter to the listed wireless devices. Network Type -- This shows the operating mode of the listed wireless devices. Version Information This screen shows information on the current version of the driver and configuration utility. You can download the latest firmware from SMC web site at http://www.smc.com. 20 NETWORK CONFIGURATION AND PLANNING SMC's EZ Connect Wireless Solution supports a stand-alone wireless network configuration, as well as an integrated configuration with wireless LANs. The SMC2635W can be configured as: · · Ad hoc - for small groups that only communicate with each other, without an Access Point Infrastructure - for wireless communication with an Access Point Network Topologies Ad Hoc Wireless LAN An ad hoc wireless LAN Ad Hoc Wireless LAN consists of a group of computers, each equipped Notebook with Wireless USB Adapter with one wireless adapter, connected via radio signals as an independent wireless LAN. Computers in a specific Notebook with Wireless PC Card ad hoc wireless LAN must therefore be configured to PC with Wireless the same radio channel. An PCI Adapter ad hoc wireless LAN can be used in a SOHO or temporary environment. 21 NETWORK TOPOLOGIES Infrastructure Wireless LAN An SMC access point can also provide wireless workstations with access to a wired LAN. An integrated wired and wireless LAN is called an infrastructure configuration. A Basic Service Set (BSS) consists of a group of wireless PC users, and an access point that is directly connected to the wired LAN. Each wireless PC in this BSS can talk to any computer in its wireless group via a radio link, or access other computers or network resources in the wired LAN infrastructure via the access point. The infrastructure configuration not only extends the accessibility of wireless PCs to the wired LAN, but also extends the effective wireless transmission range for wireless PCs by passing their signal through one or more access points. A wireless infrastructure can be used for access to a central database, or for connection between mobile workers, as shown in the following figure. Wired LAN Extension to Wireless Adapters File Server Desktop PC Switch Notebook with Wireless PC Card Adapter Access Point PC with Wireless PC I Adapter 22 SETTING THE COMMUNICATION DOMAIN Setting the Communication Domain Stationary Wireless PCs The Basic Service Set (BSS) is the communication domain for each access point. For wireless PCs that do not need to support roaming, set the domain identifier (SSID) for the wireless card to the SSID of the access point to which you want to connect. Check with your administrator for the SSID of the access point to which you should connect. Roaming Wireless PCs A wireless infrastructure can also support roaming for mobile workers. More than one access point can be configured to create an Extended Service Set (ESS). By placing the access points so that a continuous coverage area is created, wireless users within this ESS can roam freely. All wireless adapters and access points within a specific ESS must be configured with the same SS ID and to the same radio channel. File Server Desktop PC Wireless Cell Coverage Area Switch Notebook with Wireless PC Card Adapter PC with Wireless PCI Adapter Access Point Access Point PC with Wireless PC I Adapter Notebooks with Wireless PC Card Adapters Seamless Roaming Before setting up an ESS for roaming, you need to choose a clear radio channel and ideal location for the access points to maximize performance. (Refer to" Troubleshooting" on page 23 for detailed information on installation and usage.) 23 TROUBLESHOOTING TROUBLESHOOTING Check the following troubleshooting items before contacting SMC Technical Support. Adapter Installation Problems If your computer cannot find the EZ Connect Wireless Cardbus Adapter or the network driver does not install correctly, check the following: · Make sure the adapter is securely seated in the PCMCIA slot. When you insert the wireless adapter into the notebook's slot, a beep should be heard if the adapter is properly inserted. Check for any hardware problems, such as physical damage to the card's connector. Try the card in another PCMCIA slot. If this also fails, test your computer with another SMC2635W Wireless Cardbus Adapter that is known to operate correctly. Make sure your computer is using the latest BIOS. If there are other network adapters in the computer, they may be causing conflicts. Remove all other adapters from the computer and test the wireless adapter separately. If it still does not work, take out the wireless adapter. Delete the driver and utility programs. Then go to" Control Panel" and delete the adapter from your network configuration menu. Restart your notebook and reinstall the card. · · · · 24 NETWORK CONNECTION PROBLEMS Network Connection Problems If the Link LED on the Card does not light, or if you cannot access any network resources from the computer, check the following: · · · · Make sure the correct software driver is installed for your operating system. If necessary, try reinstalling the driver. Make sure the computer and other network devices are receiving power. The access point you want to attach to may be defective. Try using another access point. If you cannot access a Windows or NetWare service on the network, check that you have enabled and configured the service correctly. If you cannot connect to a particular server, be sure that you have access rights and a valid ID and password. If you cannot access the Internet, be sure you have configured your system for TCP/IP. · If your wireless station cannot communicate with a computer in the Ethernet LAN when configured for Infrastructure mode, check the following: · · · Make sure the access point that the station is associated with is powered on. If you still cannot connect, change the access point and all the stations within the BSS to another radio channel. For a station with roaming disabled, make sure the SSID is the same as that used by the access point, or the same as that used by the access points in the extended service set (ESS). 25 NETWORK CONNECTION PROBLEMS SMC Networks 802.11b Wireless Product Max. Distance Table Important Notice Maximum distances posted below are actual tested distance thresholds. However, there are many variables such as barrier composition and construction, as well as local environmental interference that may impact your actual distances and cause you to experience distance thresholds far lower than those posted below. If you have any questions or comments regarding the features or performance of this product, or if you would like information regarding our full line of wireless products, you can visit us at www.smc.com, or you can call us toll-free at 800.SMC.4YOU. SMC Networks stands behind every product sold with a 30-day satisfaction guarantee and a limited-lifetime warranty. 802.11b Wireless Cardbus Adapter Maximum Distance Table Environmental Condition Speed and Distance Ranges 11 Mbps Outdoors: A line-of-sight environment with no interference or obstruction between the Access Point and users. Indoors: A typical office or home environment with floor to ceiling obstructions between the Access Point and users. 5.5 Mbps 2 Mbps 1 Mbps 160 m (528ft) 195 m (640 ft) 255 m (837 ft) 350 m (1155 ft) 72 m (236 ft) 73 m (240 ft) 73 m (240 ft) 75 m (246 ft) 26 SPECIFICATIONS General Specifications Functional Criteria Data Rate Network Connection Operating Range Radio Signal Signal Type 1, 2, 5.5, 11 Mbps IEEE 802.11b Up to 350 m (1155 ft) at 1 Mbps Up to 160 m (528 ft) at 11 Mbps Direct Sequence Spread-Spectrum (DSSS) Operating Channel and Frequency USA - FCC: 11 channels, 2412~2462 MHz Canada - IC: 11 channels, 2412~2462 MHz Europe - ETSI: 13 channels, 2412~2472 MHz France: 4 channels, 2457~2472 MHz Japan: 14 channels, 2412~2484 MHz Sensitivity Modulation Output Power -80 dBm (typical) CCK, BPSK, QPSK >16 dBm 27 SOFTWARE DRIVERS Physical Characteristics Power Consumption 3.3 V, TX: 240 mA, RX: 160 mA Dimensions 12.8 x 5.3 cm (5.04 x 2.09 in.) Antenna Built-in antenna LED Indicator Link/Act Host Interface 32-bit Cardbus Standards Conformance Wireless Standard IEEE 802.11b Environmental Temperature Humidity Vibration/Shock/Drop Certification CE Mark Operating: 0 to 55 °C (32 to 122 °F) Storage: 0 to 70 °C (32 to 158 °F) 5 to 40% (noncondensing) IEC 68-2-34, IEC 68-2-27, IEC68-2-32 EN50081-1, EN55022 Class B EN50082-1, IEC 61000-4-2/3/4/6/11, IEC 60601-1-2 FCC Part 15 Class B, ETS 300-328, VCCI EN60950 UL1950/CSA22.2 No.950 IEC 60601-1 Emissions Safety Software Drivers NDIS Drivers Windows 98SE Windows Me Windows 2000 Windows XP 28 FOR TECHNICAL SUPPORT, CALL: From U.S.A. and Canada (24 hours a day, 7 days a week) (800) SMC-4-YOU; Phn: (949) 679-8000; Fax: (949) 679-1481 From Europe : Contact details can be found on www.smc-europe.com or www.smc.com INTERNET E-mail addresses: techsupport@smc.com european.techsupport@smc-europe.com Driver updates: http://www.smc.com/index.cfm?action=tech_support_drivers_downloads World Wide Web: http://www.smc.com http://www.smc-europe.com FOR LITERATURE OR ADVERTISING RESPONSE, CALL: U.S.A. and Canada: (800) SMC-4-YOU; Fax (949) 679-1481 Spain: 34-91-352-00-40; Fax 34-93-477-3774 UK: 44 (0) 1932 866553; Fax 44 (0) 118 974 8701 France: 33 (0) 41 38 32 32; Fax 33 (0) 41 38 01 58 Italy: 39 (0) 335 5708602; Fax 39 02 739 14 17 Benelux: 31 33 455 72 88; Fax 31 33 455 73 30 Central Europe: 49 (0) 89 92861-0; Fax 49 (0) 89 92861-230 Nordic: 46 (0) 868 70700; Fax 46 (0) 887 62 62 Eastern Europe: 34 -93-477-4920; Fax 34 93 477 3774 Sub Saharian Africa: 216-712-36616; Fax 216-71751415 North West Africa: 34 93 477 4920; Fax 34 93 477 3774 CIS: 7 (095) 7893573; Fax 7 (095) 789 35 73 PRC: 86-10-6235-4958; Fax 86-10-6235-4962 Taiwan: 886-2-8797-8006; Fax 886-2-8797-6288 Asia Pacific: (65) 238 6556; Fax (65) 238 6466 Korea: 82-2-553-0860; Fax 82-2-553-7202 Japan: 81-45-224-2332 ; Fax 81-45-224-2331 Australia: 61-2-8875-7887; Fax 61-2-8875-7777 India: 91-22-8204437 ; Fax 91-22-8204443 If you are looking for further contact information, please visit www.smc.com, www.smc-europe.com, or www.smc-asia.com. 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 Model Number: SMC2635W V.2 Revision number: E022004-R01 F1.0