3-858-024-12 (1) Trinitron® Color Computer Display Multiscan100sf Multiscan200sf Operating Instructions Mode d'emploi Manual de instrucciones EN F D ES C MODEL: CPD-100SF CPD-200SF © 1996 by Sony Corporation Owner's Record The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your dealer regarding this product. Model No. Serial No. Hinweise · Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast). · Aus ergonomischen Gründen flimmern sollten nur Darstellungen bei Vertikalfrequenzen ab 70 Hz (ohne Zeilensprung) benutzt werden. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing to qualified personnel only. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. INFORMATION This product complies with Swedish National Council for Metrology (MPR) standards issued in December 1990 (MPR II) for very low frequency (VLF) and extremely low frequency (ELF). INFORMATION Ce produit est conforme aux normes du Swedish National Council for Metrology de décembre 1990 (MPR II) en ce qui concerne les fréquences très basses (VLF) et extrêmement basses (ELF). Hinweis Dieses Gerät erfüllt bezüglich tieffrequenter (very low frequency) und tiefstfrequenter (extremely low frequency) Strahlung die Vorschriften des ,,Swedish National Council for Metrology (MPR)" vom Dezember 1990 (MPR II). INFORMACIÓN Este producto cumple las normas del Consejo Nacional Sueco para Metrología (MPR) emitidas en diciembre de 1990 (MPR II) para frecuencias muy bajas (VLF) y frecuencias extremadamente bajas (ELF). NOTICE This notice is applicable for USA/Canada only. If shipped to USA/Canada, install only a UL LISTED/CSA LABELLED power supply cord meeting the following specifications: SPECIFICATIONS Plug Type Nema-Plug 5-15p Cord Type SVT or SJT, minimum 3 × 18 AWG Length Maximum 15 feet Rating Minimum 7 A, 125 V NOTICE Cette notice s'applique aux Etats-Unis et au Canada uniquement. Si cet appareil est exporté aux Etats-Unis ou au Canada, utiliser le cordon d'alimentation portant la mention UL LISTED/CSA LABELLED et remplissant les conditions suivantes: SPECIFICATIONS Type de fiche Fiche Nema 5-15 broches Cordon Type SVT ou SJT, minimum 3 × 18 AWG Longueur Maximum 15 pieds Tension Minimum 7 A, 125 V This monitor is ENERGY STAR Compliant when used with a computer equipped with VESA Display Power Management Signaling (DPMS). As an International ENERGY STAR Partner, Sony Corporation has determined that this product meets the International ENERGY STAR Program for efficiency. Dieses Gerät entspricht den folgenden europäischen EMVVorschriften für Betrieb in Wohngebieten, gewerblichen Gebieten und Leichtindustriegebieten. EN55022/1994 Klasse B EN50082-1/1992 EN60555-2/1987 2 Table of Contents Introduction .............................................................................. 3 Precautions ...............................................................................3 Getting Started .........................................................................4 Using Your Monitor ................................................................ 4 Adjustments .............................................................................. 5 Entering New Timings ............................................................ 8 Power Saving Function ........................................................... 8 Plug and Play ........................................................................... 8 Use of the Tilt-Swivel .............................................................. 8 Damper Wire ............................................................................ 8 Specifications ............................................................................ 9 Troubleshooting ..................................................................... 10 Introduction Congratulations on your purchase of a Sony Multiscan 100sf/200sf! This monitor incorporates over 25 years of Sony experience with Trinitron display technology, ensuring excellent performance and outstanding reliability. The Multiscan 100sf/200sf's wide scan range (Multiscan 100sf: 30 ­ 70 kHz, Multiscan 200sf: 30 ­ 80 kHz), together with Digital Multiscan Technology, allows it to sync to any video mode from standard VGA through VESA 1024 × 768 at 85 Hz, VESA 1280 × 1024 at 75 Hz (Multiscan 200sf only). In addition, its two factory preset color modes and one user adjustable color mode give you unprecedented flexibility in matching on-screen colors to hard copy printouts. Furthermore, the Multiscan 100sf/200sf feature digital controls, raster rotation, power saving, low emissions, and much more. All together, it delivers incredible performance with the quality and support you can expect from Sony. Precautions Installation · Prevent internal heat build-up by allowing adequate air circulation. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. · Do not install the unit near heat sources such as radiators or air ducts, nor in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. · Do not place the unit near equipment which generates magnetism, such as a converter or high voltage power lines. Warning on Power Connection · Use the supplied power cord. For the customers in U.S.A. If you do not do this, this monitor will not conform to mandatory FCC standards. EN for 100 to 120 V AC for 220 to 240 V AC Maintenance · Clean the cabinet, glass panel and controls with a soft cloth lightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent, such as alcohol or benzine. · Do not rub, touch, or tap the surface of the screen with sharp or abrasive items, like a ball point pen or a screw driver. Otherwise, this type of contact may result in a scratched picture tube. · Before disconnecting the power cord, wait for at least 30 seconds after turning off the power switch to allow for the discharging of static electricity on the CRT display surface. · After the power has been turned on, the CRT is demagnetized for approximately 5 seconds. This generates a strong magnetic field around the bezel which may affect the data stored on magnetic tape or disks near the bezel. Place such magnetic recording equipment and tapes/disks at a distance from this unit. The socket-outlet shall be installed near the equipment and shall be easily accessible. Transportation When you transport this monitor for repairing or shipping, use the original carton box and packing materials. 3 Getting Started Before using this monitor, please make sure that the following items are included in your package: Multiscan 100sf/200sf monitor (1), power cord (1), Macintosh adapter (1), warranty card (1) and this operating instruction manual (1). This monitor will sync with any IBM or compatible system equipped with VGA or greater graphics capability. Although this monitor will sync to other platforms running at horizontal frequencies between 30 and 70 kHz (Multiscan 100sf), 30 and 80kHz (Multiscan 200sf), including Macintosh and Power Macintosh system, a cable adapter is required. Please consult your dealer for advice on which adapter is suitable for your needs. Step 1: With the computer switched off, attach the video signal cable to the video output. Using Your Monitor Preset and User Modes The Multiscan 100sf/200sf has factory preset modes for the 7 most popular industry standards for true "plug and play" capability. For less common modes, the Multiscan 100sf/200sf 's Digital Multiscan Technology will perform all of the complex adjustments necessary to ensure a high quality picture for any timing between 30 and 70 kHz (Multiscan 100sf ), 30 and 80 kHz (Multiscan 200sf ). CPD-100SF No. Resolution Horizontal Vertical Graphics (dots × lines) Frequency Frequency Mode 1 2 3 4 640 × 480 800 × 600 800 × 600 832 × 624 1024 × 768 1024 × 768 31.5 kHz 46.9 kHz 53.7 kHz 49.7 kHz 60.0 kHz 68.7 kHz 60 Hz 75 Hz 85 Hz 75 Hz 75 Hz 85 Hz 60 Hz VGA Graphic 1) VESA 2) VESA 2) IBM or compatible computer Macintosh 16" Color 3) VESA 2) VESA 2) VESA 2) to video output 5 6 7 1280 × 1024 64.0kHz Apple computer HD15 - HD15 adapter (not supplied) may be required to video output Macintosh adapter (supplied) CPD-200SF No. Resolution Horizontal Vertical Graphics (dots × lines) Frequency Frequency Mode 1 2 3 4 5 6 7 8 9 640 × 480 800 × 600 800 × 600 832 × 624 1024 × 768 1024 × 768 1024 × 768 1152 × 870 31.5 kHz 46.9 kHz 53.7 kHz 49.7 kHz 60.0 kHz 60.2 kHz 68.7 kHz 68.7 kHz 60 Hz 75 Hz 85 Hz 75 Hz 75 Hz 75 Hz 85 Hz 75 Hz 75 Hz VGA Graphic 1) VESA 2) VESA 2) Notes : · Use a HD15 (Female) - HD15 (Male without the No.9 pin) adapter (not supplied) for any current DOS computer which is not compatible with DDC 2 AB and its No.9 pin is disconnected. · Supplied Macintosh adapter is compatible with Macintosh LC, Performa, Quadra and Power Macintosh series computers. Macintosh II series and some older version of PowerBook models may need an adapter with micro switches. Step 2: Attach the power cord to the monitor and the other end to a power outlet. Macintosh 16" Color 3) VESA 2) Macintosh 19" Color 3) VESA 2) Macintosh 21" Color 3) VESA 2) 1280 × 1024 80.0 kHz For the customers using the Windows®4)95 Install the new model information of the Sony computer display Power cord (supplied) to a power outlet This monitor complies with "VESA DDC," the standards of Plug&Play. If your PC/graphic board complies with DDC, select "Plug and Play Monitor (VESA DDC)" or this monitor's model name (CPD-100SF or CPD-200SF) as "Monitor type" from "Control Panel" on Windows95. Some PC/graphic boards do not comply with DDC. Even if they comply with DDC, they may have some problems on connecting this monitor. In this case, select this monitor's model name (CPD-100SF or CPD-200SF) as "Monitor type" on Windows95. from "Windows95 Monitor Information Disk" into your PC. (To install the file, refer to the attached "About the Windows95 Monitor Information Disk/File"). Step 3: Step 4: Turn on the monitor and computer. If necessary, adjust the user controls according to your personal preference. The installation of your Multiscan 100sf/200sf is complete. Enjoy your monitor. 1) VGA is a trademark of IBM Corporation. 2) VESA is a trademark of the non-profit organization, Video Electronics Standard Association. 3) Macintosh is a trademark of Apple Computer Inc. 4) Windows® is a registered trademark of Microsoft Corporation in the United States and other countries. Recommended horizontal timing conditions Horizontal sync width should be: >1.0 µsec. Horizontal blanking width should be: >3.6 µsec. (Multiscan 100sf)/ >3.0 µsec. (Multiscan 200sf) Vertical sync width should be: < 560 µsec. Note CPD-100SF does not apply to Macintosh 21" color mode. 4 Adjustments When one of the preset-type signals is input, no picture adjustment is necessary. You can, however, adjust the picture to your preferences by following the procedure described below. You can adjust the all items on the OSD (On Screen Display). Control Panel POWER SAVING p p Before adjusting the items, turn on the unit and feed the video signal from the connected computer/work station. Adjustments will be stored automatically. RESET COLOR GEOM SIZE CENTER POWER Adjusting the Picture Brightness The adjustment data becomes the common setting for all input si ...