User manual SONY CPD-201VS

3-864-163-13 (1) Trinitron® Multimedia Computer Display Operating Instructions CPD-101VS CPD-201VS © 1998 by Sony Corporation Owner's Record The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your dealer regarding this product. Model No. Serial No. NOTICE This notice is applicable for USA/ Canada only. If shipped to USA/Canada, install only a UL LISTED/CSA LABELLED power supply cord meeting the following specifications: SPECIFICATIONS Plug Type Nema-Plug 5-15p Cord Type SVT or SJT, minimum 3 × 18 AWG Length Maximum 15 feet Rating Minimum 7 A, 125 V WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing to qualified personnel only. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. NOTICE Cette notice s'applique aux Etats-Unis et au Canada uniquement. Si cet appareil est exporté aux EtatsUnis ou au Canada, utiliser le cordon d'alimentation portant la mention UL LISTED/CSA LABELLED et remplissant les conditions suivantes: SPECIFICATIONS Type de fiche Fiche Nema 5-15 broches Cordon Type SVT ou SJT, minimum 3 × 18 AWG Longueur Maximum 15 pieds As an ENERGY STAR Partner, Sony Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency. ENERGY STAR is a U.S. registered mark. 2 Declaration of Conformity Model Number : CPD-101VS CPD-201VS Trade Name : SONY Responsible party : Sony Electronics Inc. Address : 1 Sony Drive, Park Ridge, New Jersey 07656 U.S.A. Telephone number : 201-930-6970 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION This product complies with Swedish National Council for Metrology (MPR) standards issued in December 1990 (MPR II) for very low frequency (VLF) and extremely low frequency (ELF). INFORMATION Ce produit est conforme aux normes du Swedish National Council for Metrology de décembre 1990 (MPR II) en ce qui concerne les fréquences très basses (VLF) et extrêmement basses (ELF). Hinweis Dieses Gerät erfüllt bezüglich tieffrequenter (very low frequency) und tiefstfrequenter (extremely low frequency) Strahlung die Vorschriften des ,,Swedish National Council for Metrology (MPR)" vom Dezember 1990 (MPR II). INFORMACIÓN Este producto cumple las normas del Consejo Nacional Sueco para Metrología (MPR) emitidas en diciembre de 1990 (MPR II) para frecuencias muy bajas (VLF) y frecuencias extremadamente bajas (ELF). Dieses Garät entspricht den folgenden europäischen EMV-Vorschriften für Betrieb in Wohngebieten, gewerblicher Gebleten und Leichtindustriegebieten. EN55022/1994 Klasse B EN50082-1/1992 EN61000-3-2/1995 Hinweise · Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast). · Aus ergonomischen Gründen (flimmern) sollten nur Darstellungen bei Vertikalfrequenzen ab 70 Hz (ohne Zeilensprung) verwendet werden. · Die Konvergenz des Bildes kann sich auf Grund des Magnetfeldes am Ort der Aufstellung aus der korrekten Grundeinstellung verändern. Zur Korrektur empfiehlt es sich deshalb, die Regler an der Frontseite für Konvergenz so einzustellen, daß die getrennt sichtbaren Farblinien für Rot, Grün und Blau bei z.B. der Darstellung eines Buchstabens zur Deckung (Konvergenz) gelangen. Siehe hierzu auch die Erklärungen zu Konvergenz. VCCI B 3 4 Table of Contents Introduction ................................................................................. 6 Plug and play ............................................................................................... 6 Precautions ................................................................................... 7 Functions of Controls .................................................................. 9 Getting Started .......................................................................... 11 Installation ................................................................................................. 12 Using Your Display .................................................................... 14 Preset and user modes.............................................................................. 14 Using the tilt-swivel .................................................................................. 15 Damper wire .............................................................................................. 16 Adjustments ............................................................................... 17 Introducing the On-Screen Display ........................................................ Adjusting the sound volume ................................................................... Adjusting the picture contrast ................................................................. Adjusting the picture brightness ............................................................ Adjusting the picture centering .............................................................. Adjusting the picture size ........................................................................ Adjusting the geometry ........................................................................... Selecting the color temperature .............................................................. Adjusting the convergence (CPD-201VS only) ..................................... Adjusting the screen moiré ...................................................................... Activating screen degauss ....................................................................... Changing the OSD position ..................................................................... Selecting the OSD language .................................................................... Resetting ..................................................................................................... 17 19 21 21 22 23 24 25 26 27 28 29 30 31 Graphic Picture Enhancement (GPE) ......................................... 32 Available GPE modes ............................................................................... 32 Selecting the GPE mode ........................................................................... 33 Power Saving Function ............................................................. 34 Specifications ............................................................................. 35 Troubleshooting ......................................................................... 37 Self-diagnosis function .............................................................. Back cover 5 Introduction Congratulations on your purchase of a Sony Multimedia CPD-101VS/ 201VS display! This display incorporates over 25 years of Sony experience with Trinitron display technology, ensuring excellent performance and outstanding reliability. This display's wide scan range (30 ­ 70 kHz), together with Digital Multiscan Technology, allows it to sync to any video mode from standard VGA through VESA 1024 × 768 at 85 Hz (VESA 1280 × 1024 at 60 Hz). In addition, its four factory-preset color modes give you unprecedented flexibility in matching on-screen colors to hard copy printouts. Furthermore, it features: · Graphic Picture Enhancement function improves monitor performance to match the application that you are running. With the GPE AUTO MODE, you can use "IntelliLight" compatible software which will maximize the color and brightness of a window running a multimedia presentation without affecting the brightness and contrast of text based applications. · Integrated stereo speakers with Bass Boost enables you to enjoy excellent sound reproduction via 3.0 W stereo speakers. All together, CPD-101VS/201VS delivers incredible performance with the quality and support you can expect from Sony. Plug and play This display complies with DDCTM1 and DDC2B which are the Display Data Channel (DDC) standards of VESA. When a DDC1 host system is connected, the display synchronizes with the V. CLK in accordance with the VESA standards and outputs the EDID (Extended Display Identification Data) to the data line. When a DDC2B host system is connected, the display automatically switches to DDC2B communication. DDCTM is a trademark of Video Electronics Standard Association. 6 Introduction Precautions Installation · Prevent internal heat build-up by allowing adequate air circulation. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. · Do not install the unit near heat sources such as radiators or air ducts, nor in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. · Do not place the unit near equipment which generates magnetism, such as a converter or high voltage power lines. Maintenance · Clean the cabinet, glass panel and controls with a soft cloth lightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent, such as alcohol or benzine. · Do not rub, touch, or tap the surface of the screen with sharp or abrasive items, like a ball point pen or a screwdriver, as this type of contact may result in a scratched picture tube. Transportation · Do not discard the carton and packing materials. When transporting the unit, use these packing materials so that the unit is properly packaged. · When carrying the unit, be careful not to get your hands caught between the display and the tilt-swivel. Continued to the next page Precautions 7 Warning on Power Connection · Use the supplied power cord. For the customers in U.S.A. If you do not do this, this display will not conform to mandatory FCC standards. For the customers in UK. If you use the display in the UK, please use the supplied UK cable with the UK plug. for 100 to 120 V AC for 220 to 240 V AC for 240 V AC only · Before disconnecting the power cord, wait at least 30 seconds after turning off the power switch to discharge static electricity from the CRT display surface. · After the power has been turned on, the CRT is demagnetized for approximately 5 seconds. This generates a strong magnetic field around the bezel which may affect the data stored on magnetic tape or disks near the bezel. Place such magnetic recording equipment and tapes/disks at a distance from this unit. The socket-outlet shall be installed near the equipment and shall be easily accessible. 8 Precautions Functions of Controls Front 1 2 3 45 6 789 !º 1 2 3 4 5 6 7 8 9 !º Microphone Screen Stereo speakers ¤ Mute button ? Reset switch GPE button and indicator . Volume +/­ buttons MENU button > +/­ Contrast buttons U Power switch and indicator -- -- -- Mutes sound (page 20). Resets adjustments to factory setting (page 31). Sets GPE mode (page 32). Adjust speaker volume (page 19). Use to select items in an OSD. Displays the OSD menu. Adjust picture contrast (page 21). Use to adjust items in an OSD. Turns the display on and off. Functions of Controls 9 Rear !¡ !TM !£ !¢ !¡ !TM !£ !¢ ! AC IN connector 2 Audio plug (green) h MIC plug (red) ; Video signal cable (blue) 2 Headphones jack ! !§ !¶ Connect the supplied power cord (page 13). Connect to the computer's audio output (page 12). Connect to the computer's microphone input (page 12). Connect to the computer's video output (page 12). Connect standard mini-plug headphones (not supplied). The speakers are turned off when headphones are connected. Adjusts the angle of the display (page 15). Connect to a subwoofer's input (not supplied). !§ !¶ Tilt-Swivel Subwoofer output jack 10 Functions of Controls Getting Started Before using this display, please make sure that the following items are included in your package: · Multimedia computer display (1) · Power cord (1) · Warranty card (1) · Operating instructions manual (1) · Windows Monitor Information Disk and its instruction manual (1) Tip This display will sync with any IBM or compatible system equipped with VGA1) or greater graphics capability. Although this display will sync to other platforms running at horizontal frequencies between 30 and 70 kHz, including Macintosh2) and Power Macintosh systems, a cable adapter is required. Please consult Sony Technical Support for advice on which adapter is suitable for your needs. 1) VGA is a trademark of IBM Corporation. 2) Macintosh is a trademark of Apple Computer Inc. Continued to the next page Getting Started 11 Installation p Step 1: Connect the computer With the computer switched off, connect the video signal cable to the display (VGA) connector on your computer. If your computer supports the DDC plug-and-play standard, this connection will enable DDC communication between the display and the computer. The video signal cable is combined with audio and microphone cables. If your computer is equipped with sound capability, connect the audio (green) and microphone (red) plugs to appropriate jacks located on your computer. 2 PRINTER AL MONITOR LINE OUT LINE IN MIC USB CONTR Blue (to monitor connector) Green (to LINE OUT connector) Red (to microphone connector) Fasten the screw of the blue plug. Computer Note on handling the video signal cable Do not touch the pins of the video signal cable. 12 Getting Started p Step 2: Connect the power cord With the display switched off, connect the power cord to the display and the other end to a power outlet. to a power outlet Power cord (supplied) p Step 3: Turn on the display, and then your computer. For proper Plug and Play recognition, turn on the display before you turn on your computer. Note on Warning Messages If there is something wrong with the input signal, one of the following messages appears. "OUT OF SCAN RANGE" This indicates that the input signal is not supported by the display's specifications. "NO INPUT SIGNAL" This indicates that video signal is missing. To solve these problems, see "Troubleshooting" on page 37. p Step 4: If necessary... Adjust the user controls according to your personal preference. The installation of your display is complete. Enjoy your display. Getting Started 13 Using Your Display Preset and user modes The Multimedia CPD-101VS/201VS display has factory preset modes for the 9 most popular industry standards for true "plug and play" capability. For less common modes, its Digital Multiscan Technology will perform all of the complex adjustments necessary to ensure a high quality picture for any timing between 30 and 70 kHz. NO. 1 2 3 4 5 6 7 8 9 Resolution (dots × lines) 640 × 400 640 × 480 640 × 480 800 × 600 800 × 600 1024 × 768 1024 × 768 1152 × 864 1280 × 1024 Horizontal Frequency 31.5 kHz 31.5 kHz 43.3 kHz 37.9 kHz 46.9 kHz 60.0 kHz 68.7 kHz 54.8 kHz 64.0 kHz Vertical Frequency 70 Hz 60 Hz 85 Hz 60 Hz 75 Hz 75 Hz 85 Hz 60 Hz 60 Hz Note for Windows® 95/98 users To maximize the potential of your display, install the new model information file from the supplied Windows® Monitor Information Disk onto your PC. This display complies with the "VESA DDC" Plug & Play standard. If your PC/graphics board complies with DDC, select "Plug & Play Monitor (VESA DDC)" or this display's model name as the monitor type in the "Control Panel" of Windows® 95/98. If your PC/graphics board has difficulty communicating with this display, load the Windows® Monitor Information Disk and select this display's model name as the monitor type. Windows® is a registered trademark of Microsoft Corporation in the United States and other countries. Note on recommended horizontal timing conditions Horizontal sync width should be more than 1.0 µsec. Horizontal blanking width should be more than 3.6 µsec. 14 Using Your Display p To enter new timings When using a video mode that is not one of the 9 factory preset modes, some fine tuning may be required to optimize the display to your preferences. Simply adjust the display according to the adjustment instructions. The adjustments will be stored automatically and recalled whenever that mode is used. A total of 16 user-defined modes can be stored in memory. If a 17th mode is entered, it will replace the first. Using the tilt-swivel With the tilt-swivel, this unit can be adjusted to be viewed at your desired angle within 90° horizontally and 7° vertically. To turn the unit vertically and horizontally, hold it at its bottom with both hands. Be careful not to get your hands caught between the display and the tiltswivel. 45° 7° 45° Using Your Display 15 Damper wire Using a white background, a very thin horizontal line on the screen may be visible as shown below. This line is the damper wire. The Trinitron tube has a vertically striped Aperture Grille inside. The Aperture Grille allows more light to pass through to the screen giving the Trinitron CRT more color and brightness. The damper wire is attached to the Aperture Grille to prevent vibration of the Aperture Grille wire so that the screen image is constantly stable. Approx. 6 cm (2 3/8 inches) (CPD-201VS only) Damper wires Approx. 6 cm (2 3/8 inches) 16 Using Your Display Adjustments When one of the preset-type signals is input, no picture adjustment is necessary. You can, however, adjust the picture to your preference by following the procedure described below. To adjust the display, turn on the display and computer. Introducing the On-Screen Display Beyond sound volume and picture contrast adjustment, most adjustments are made using the OSD menu system. Using the OSD menu 1. Press the MENU button to display the MENU OSD. MENU OK MENU COLOR CENTER SCREEN BRIGHT GEOM EXIT SIZE ZOOM OPTION 2. Use the the four arrow (>/./?//) buttons (. +/­ and > +/­ buttons) to select the item you want to adjust. Change the item from blue to yellow. MENU OK MENU COLOR CENTER SCREEN BRIGHT GEOM EXIT SIZE ZOOM OPTION 3. Press the MENU button again. The item is selected and the item's OSD appears. BRIGHT/CONTRAST 50 BRIGHTNESS Adjustments 17 Summary of each item 1 MENU 2 3 OK MENU 9 8 COLOR CENTER SCREEN BRIGHT GEOM EXIT SIZE ZOOM OPTION 4 7 6 5 1 COLOR Selects the color temperature. 2 CENTER Adjusts the picture centering. 3 SCREEN Reduces the moiré pattern. Adjusts the vertical and horizontal convergence (CPD-201VS only). 4 ZOOM Adjusts the picture size in horizontal and vertical direction proportionally. 5 OPTION Activates bass-boost and screen degauss, changes the OSD position and selects the OSD language. 6 SIZE Adjusts the picture size. You can adjust the size in horizontal or vertical direction individually. 7 GEOM Adjusts the picture rotation, pincushion, etc. 8 BRIGHT Adjusts the picture brightness and contrast. 9 EXIT Closes the OSD menu. 18 Adjustments Adjusting the sound volume 1. Press the . + or ­ button. The VOLUME/CONTRAST OSD appears. The horizontal and vertical frequencies for each input signal received appear. VOLUME/CONTRAST 26 65. 0kHz / 26 76Hz Horizontal frequency Vertical frequency 2. Press the . +/­ buttons to adjust volume. + to increase volume ­ to decrease volume The VOLUME/CONTRAST OSD disappears three seconds after you release the buttons. Tips · Adjust the volume while listening to the sound. · Excessively high volume may cause howling. p To activate Bass Boost for rich bass sound 1. Select OPTION in the MENU OSD and press the MENU button. The OPTION OSD appears. MENU OK MENU OPTION OFF ON COLOR CENTER SCREEN BRIGHT GEOM EXIT SIZE ZOOM BASS BOOST OPTION Continued to the next page Adjustments 19 2. Select BASS BOOST with the >/. buttons. 3. Press the / button to select ON. To cancel bass boost, press the ? button to select OFF. OPTION OFF ON BASS BOOST To exit the OSD Press the MENU button again. Tip If you don't touch any buttons, the OSD automatically disappears after 30 seconds. p To mute the sound Press the ¤ button. The ¤ indicator appears while the sound is muted. Press again to cancel muting. You can cancel muting also by pressing the . + button. Tip ¤ appears instead of . on the VOLUME/CONTRAST OSD while the sound is muted. 20 Adjustments