3-858-485-31 (1) Trinitron® Color Computer Display Multiscan300sf Operating Instructions Mode d'emploi Bedienungsanleitung Manual de instrucciones Istruzioni per l'uso EN F D ES I MODEL: CPD-300SFT5 © 1996 by Sony Corporation Owner's Record The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your dealer regarding this product. Model No. Serial No. Hinweise · Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast). · Aus ergonomischen Gründen flimmern sollten nur Darstellungen bei Vertikalfrequenzen ab 70 Hz (ohne Zeilensprung) benutzt werden. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing to qualified personnel only. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. INFORMATION This product complies with Swedish National Council for Metrology (MPR) standards issued in December 1990 (MPR II) for very low frequency (VLF) and extremely low frequency (ELF). INFORMATION Ce produit est conforme aux normes du Swedish National Council for Metrology de décembre 1990 (MPR II) en ce qui concerne les fréquences très basses (VLF) et extrêmement basses (ELF). Hinweis Dieses Gerät erfüllt bezüglich tieffrequenter (very low frequency) und tiefstfrequenter (extremely low frequency) Strahlung die Vorschriften des ,,Swedish National Council for Metrology (MPR)" vom Dezember 1990 (MPR II). INFORMACIÓN Este producto cumple las normas del Consejo Nacional Sueco para Metrología (MPR) emitidas en diciembre de 1990 (MPR II) para frecuencias muy bajas (VLF) y frecuencias extremadamente bajas (ELF). Dieses Gerät entspricht den folgenden europäischen EMVVorschriften für Betrieb in Wohngebieten, gewerblichen Gebieten und Leichtindustriegebieten. EN55022/1987 Klasse B EN50082-1/1992 EN60555-2/1987 NOTICE This notice is applicable for USA/Canada only. If shipped to USA/Canada, install only a UL LISTED/CSA LABELLED power supply cord meeting the following specifications: SPECIFICATIONS Plug Type Nema-Plug 5-15p Cord Type SVT or SJT, minimum 3 × 18 AWG Length Maximum 15 feet Rating Minimum 7 A, 125 V NOTICE Cette notice s'applique aux Etats-Unis et au Canada uniquement. Si cet appareil est exporté aux Etats-Unis ou au Canada, utiliser le cordon d'alimentation portant la mention UL LISTED/CSA LABELLED et remplissant les conditions suivantes: SPECIFICATIONS Type de fiche Fiche Nema 5-15 broches Cordon Type SVT ou SJT, minimum 3 × 18 AWG Longueur Maximum 15 pieds Tension Minimum 7 A, 125 V This monitor complies with the TCO'95 guidelines . This monitor is ENERGY STAR Compliant when used with a computer equipped with VESA Display Power Management Signaling (DPMS). As an International ENERGY STAR Partner, Sony Corporation has determined that this product meets the International ENERGY STAR Program for efficiency. 2 Table of Contents Introduction .............................................................................. 3 Precautions ...............................................................................3 Getting Started .........................................................................4 Using Your Monitor ................................................................ 5 Adjustments .............................................................................. 6 Entering New Timings .......................................................... 10 Power Saving Function ......................................................... 10 Plug and Play ......................................................................... 10 Use of the Tilt-Swivel ............................................................ 10 Damper Wire .......................................................................... 10 Specifications .......................................................................... 11 Troubleshooting ..................................................................... 11 Introduction Congratulations on your purchase of a Sony Multiscan SF series monitor! This monitor incorporates over 25 years of Sony experience with Trinitron display technology, ensuring excellent performance and outstanding reliability. The advanced design of the SF series together with Digital Multiscan Technology allows it to sync to any video mode within its wide scan range. In addition, its three factory preset color modes and one user adjustable color mode give you unprecedented flexibility in matching on-screen colors to hard copy print outs. Furthermore, this monitor features digital controls with OSD (On Screen Display). It delivers easier adjustment by visualizing your control statement. All together, it delivers incredible performance with the quality and support you can expect from Sony. Precautions Installation · Prevent internal heat build-up by allowing adequate air circulation. Do not place the unit on surfaces (rugs, blankets, etc.) nor near materials (curtains, draperies) that may block the ventilation holes. · Do not install the unit near heat sources such as radiators or air ducts, nor in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. · Do not place the unit near equipment which generates magnetism, such as a converter or high voltage power lines. Maintenance · Clean the cabinet, panel and controls with a soft cloth lightly moistened with a mild detergent solution. Do not use any type of abrasive pad, alkaline cleaner, scouring powder or solvent, such as alcohol or benzine. · Do not rub, touch, or tap the surface of the screen with sharp or abrasive items, like a ball point pen or a screw driver. Otherwise, this type of contact may result in a scratched picture tube. EN Warning on Power Connection · Use a proper power cord for your local power supply. For the customers in U.S.A. If you do not do this, this monitor will not conform to mandatory FCC standards. For the customers in UK If you use the monitor in UK, please use the supplied UK cable with UK plug. Examples of plug shape: · Before disconnecting the power cord, wait for at least 30 seconds after turning off the power switch to allow for the discharging of static electricity on the CRT display surface. · After the power has been turned on, the CRT is demagnetized for approximately 5 seconds. This generates a strong magnetic field around the bezel, which may affect the data stored on magnetic tapes or disks near the bezel. Place such magnetic recording equipment and tapes/disks apart from this unit. The socket-outlet should be installed near the equipment and be easily accessible. for 100 to 120 V AC for 220 V to 240 V AC for 240 V AC only 3 Getting Started This monitor will sync with any IBM or compatible system equipped with VGA or greater graphics capability. Although this monitor will sync to other platforms running at horizontal frequencies between 30 and 86 kHz, including Macintosh and Power Macintosh system, a cable adapter is required. Please consult your dealer for advice on which adapter is suitable for your needs. Step 1: With the computer switched off, attach the video signal cable to the monitor (HD15/5 BNC's) and attach the other end to the video card. Step 3: Turn on the monitor and computer. Step 4: Switch the input connector according to the adjustment procedure on page 9. Step 5: If necessary, adjust the user controls according to your personal preference. to HD15 IBM or Compatible Computer to video output Video signal cable (supplied) HD15 - HD15 adapter (supplied) may be required Apple Computer to video output Step 2: With the monitor switched off, attach the power cord to the monitor and the other end to the power outlet. Power cord (supplied) to a wall outlet For the customers using the Windows®4) 95 Even if you select SONY for the maker on the device select screen, the model name (CPD-300SFT5) may not appear. In this case, select the DDC standard monitor. The installation of your monitor is complete. Enjoy your monitor. Notice To comply with the limits of FCC Class B and IC Class B for digital device, please attach the supplied video signal cable for HD15 input or SMF-400 (sold separately) for BNC input. Furthermore, each cable has ferrite cores on it. Macintosh adapter (not supplied) IBM or Compatible to video output Computer to VIDEO IN R/G/B SYNC IN HD/VD HD15 - HD15 adapter (supplied) may be required Apple Computer to video output Video signal cable SMF-400 (sold separately) Macintosh adapter (not supplied) For the customers using IBM PC or IBM compatible system which is not compatible with DDC2AB and DDC2B+ This monitor uses a No.9 pin in the video signal connector for DDC2AB and DDC2B+ compatibility. Some PC systems which are not compatible with either DDC2AB or DDC2B+ may not accept the No.9 pin. If you are not sure whether your PC system accepts the No.9 pin or not, use the HD15 (Female) - HD15 (Male without the No.9 pin) adapter (supplied). Make sure that the male side (without the No.9 pin) is connected to the computer. 4 Using Your Monitor Preset and User Modes The Multiscan 300sf has factory preset modes for the 10 most popular industry standards for true "plug and play" capability. For less common modes, the Multiscan 300sf's Digital Multiscan Technology will perform all of the complex adjustments necessary to ensure a high quality picture for any timing between 30 and 86 kHz. However, due to the wide variety of video boards on the market, it may be necessary for the user to fine tune the vertical/horizontal size and centering. Note: For Windows users, check your video board manual or the utility program which comes with your graphic board and select the highest available refresh rate to maximize monitor performance. Recommended horizontal timing conditions Horizontal sync width should be: >4.8% of total horizontal time. Horizontal blanking width should be: >3.0 µsec. No. Resolution (dots × lines) 1 2 3 4 5 6 7 8 9 640 × 480 720 × 400 640 × 480 832 × 624 800 × 600 1024 × 768 1280 × 1024 1024 × 768 1152 × 870 Horizontal Vertical Graphics Mode Frequency Frequency 31.5 kHz 31.5 kHz 43.3 kHz 49.7 kHz 53.7 kHz 60.0 kHz 64.0 kHz 68.7 kHz 68.7 kHz 80.0 kHz 60 Hz 70 Hz 85 Hz 75 Hz 85 Hz 75 Hz 60 Hz 85 Hz 75 Hz 75 Hz VGA Graphic 1) VGA Text 1) VESA 2) Macintosh 16" Color 3) VESA 2) Macintosh 19" Color 3) VESA 2) VESA 2) Macintosh 21" Color 3) VESA 2) 10 1280 × 1024 1) VGA is a trademark of IBM Corporation. 2) VESA is a trademark of Video Electronics Standard Association. 3) Macintosh is a trademark of Apple Computer Inc. 4) Windows ® is a registered trademark of Microsoft. Corporation in the United States and other countries. EN 5 Adjustments When one of the preset-type signals is input, no picture adjustment is necessary. You can, however, adjust the picture to your preferences by the following procedure described below. You can adjust the all items on the OSD (On Screen Display). The item to be adjusted is indicated in white on the OSD. Control Panel POWER SAVING p p Before adjusting the items, turn on the unit and feed the video signal from the connected computer/work station. Adjustments will be stored automatically. RESET COLOR CONV GEOM SIZE CENTER Adjusting the Picture Brightness The adjustment data becomes the common setting for all input signals. Adjusting the Picture Centering The adjustment data becomes the individual setting for each input signal received. 1 Press the ¨ ?// button. The "BRIGHTNESS/CONTRAST" OSD (On Screen Display) appears. BRIGHTNESS/CONTRA ...