4-088-512-11 (2) Trinitron Color TV Operating Instructions · Before operating the unit, please read this manual thoroughly and retain it for future reference. GB CT · Panduan Pengendalian · Sebelum mengendalikan unit, sila baca buku panduan ini dengan teliti dan simpan untuk rujukan masa depan. MY KV-DR34 KV-DR29 © 2002 Sony Corporation M69 WARNING · Dangerously high voltages are present inside the TV. · TV operating voltage: 110 ­ 240 V AC. · Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground. · To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immediately wash it away with water. For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms. For children's safety, do not leave children alone with the TV. Do not allow children to climb onto it. To prevent fire or shock hazard, do not expose the TV to rain or moisture. Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only. Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet. Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not attach anything (e.g., adhesive tape, cellophane tape, glue) on the painted cabinet of the TV. Do not scratch the picture tube. Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel. Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations. 2 Do not place any objects on the TV. Do not plug in too many appliances to the same power socket. Do not damage the power cord. Install the TV on a stable TV stand and floor which can support the TV set weight. Ensure that the TV stand surface is flat and its area is larger than the bottom area of the TV. Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Unplug the TV before moving it or if you are not going to use it for several days. 3 x Securing the TV To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV. 20 mm 3.8 mm screws clamps band Screw the band to the TV stand and to the provided hole at the rear of your TV. or (1) Put a cord or chain through the clamps. (2) Screw one clamp to a wall or pillar and the other clamp to the provided hole at the rear of your TV. or (1) Attach each end of a cord or chain to the provided holders at the rear of your TV. (2) Securely fix the attached cord or chain to a wall or pillar using an attachment which can support the TV set weight. Note · Use only the supplied screws. Use of other screws may damage the TV. 4 Table of Contents Installation Getting Started ..................................... 6 Setting up your TV ("INITIAL SETUP") ............................. 7 Menu Adjustment Introducing the menu system .......... 18 Changing the "PICTURE" setting ... 21 Changing the "SOUND" setting ..... 23 Changing the Picture-in-Picture ("PIP") setting .................................... 25 Changing the "SETUP" setting ........ 26 Changing the Channel Preset ("CH PRESET") setting ..................... 28 Overview of Controls TV front and rear panels ..................... 8 Remote control ..................................... 9 Advanced Operations Selecting the picture and sound modes .................................................. 11 Viewing higher quality pictures with DRC-MF ..................................... 12 Viewing the picture in wide mode .. 12 Watching Picture-in-Picture (PIP) ... 13 Selecting a TV program using PIP .. 14 Listening with surround sound ....... 14 Setting the timers ............................... 15 Enjoying stereo or bilingual programs ............................................. 16 Viewing Teletext ................................. 17 Additional Information Connecting optional components ... 31 Troubleshooting ................................. 33 Specifications ...................... Back cover GB 5 Installation x Getting Started 1 Step 1 Insert the batteries (supplied) into the remote. Note · Do not use old or different types of batteries together. I N I T I A L S E T UP L AN GU AGE : ENG L I SH b Step 2 Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV. Tip · You can also connect your TV to other optional components (see page 31). Step 3 Plug in the power cord, then press ! on the TV to turn it on. b Step 4 Set up the TV by following the instructions of the "INITIAL SETUP"menu (see page 7). 6 Installation x Setting up your TV ("INITIAL SETUP") MENU SOUND When you turn on your TV for the first time, the "INITIAL SETUP" menu will appear. This menu allows you to change the menu V/v/ENTER language, adjust the picture position and preset the TV channels automatically. PIP PROGR MENU ENTER DRC-MF Installation PIP PROGR PIC MODE 1 Press V or v to select the desired menu language (e.g.,"ENGLISH"), then press ENTER. The selected menu language appears. I N I T I A L S E T UP L AN GU AGE : ENG L I SH 2 If the "PIC ROTATION" bar is slanted, press V or v to adjust it, then press ENTER. If no adjustment is necessary, then press ENTER. or icon on the screen The flashes while adjusting. Rotate anticlockwise I N I T I A L S E T UP Rotate clockwise PIC ROT A T I ON Refer to this bar when adjusting. I N I T I A L S E T UP START AUTO PROGRAM NOW? Y ES NO 3 Press V or v to select "YES", then press ENTER to preset the channels automatically (see page 28). The screen will indicate automatic presetting is in progress. To skip automatic channel presetting, select "NO", then press ENTER. I N I T I A L S E T UP PR : 0 9 T V S Y S : AUTO V H F L OW 4 Press V or v to select "NO", then press ENTER. The "INITIAL SETUP" menu will not appear again the next time you turn on the TV by pressing !. To allow this menu to appear again, select "YES", then press ENTER. I N I T I A L S E T UP D I S P L A Y T H I S M ENU NE X T T I M E ? Y ES NO Tip · You can immediately go to the end of the "INITIAL SETUP" menu by pressing MENU. · You can also set up your TV using the menu system (see page 18). Installation 7 Overview of Controls x TV front and rear panels TV rear panel qa R 1 L 2 Y PB/CB PR/CR 3 qs 4 AUTO MENU PROGR ENTER SELECT L(MONO) R PROGR qf TV front panel qd 0 9 8 76 ENTER 5 SELECT 4 3 2 1 L(MONO) R 4 AUTO MENU PROGR PROGR Button/Terminal 1! 21 2 2 3 4 PROGR +/­ 5 2 +/­ 6t 7 AUTO PROGR Menu operations 5 SELECT V/v 6 ENTER 8 MENU 9 t4 0i qa qs 8 qd T qf t1, t2, t3 Function Turn off or turn on the TV. Standby indicator. Wake Up indicator. Stereo/bilingual indicator. Remote control sensor. Select program number. Adjust volume. Select TV or video input. Preset channels automatically. Select and adjust items Confirm selected items Display or cancel the menu Video input terminal 4. Headphone jack. Component video input terminal. Antenna input terminal. Monitor output terminal. Video input terminal 1, 2, 3. Page ­ ­ 15 16 ­ ­ ­ ­ ­ 20 20 20 31 ­ 32 31 31 31 8 Overview of Controls x Remote control qf qg qh qj 1 4 7 DVD 1 2 3 2 5 8 0 SOUND Button 1 ?/1 3a 4 0 ­ 9, 5 JUMP Function Turn off temporarily or turn on the TV. Display the TV input. Input numbers. Jump to previous program number. Select surround mode. Select wide-mode (16:9). Select program number. Display on-screen information. Mute the sound. Select component video input. Select TV or video input. Select DRC-MF mode. Select sound mode. Select picture mode. Adjust volume. Set TV to turn off automatically. Set TV to turn on automatically. Display a sub screen. Swap main and sub screens. Display and change programs in the sub screen. Select a video input in the sub screen. Swap sound between main and sub screen. Change sub screen to main screen. Select stereo/bilingual mode. Page ­ ­ Overview of Controls ­ ­ 14 12 ­ ­ ­ 32 31 12 11 11 ­ 15 15 3 6 9 JUMP 4 5 6 7 8 9 0 qa 9 SURROUND 0 WIDE MODE qa PROGR +/­ qf qg % qh DVD qj t wa DRC-MF ws SOUND MODE wd PIC MODE wf 2 +/­ Timer operations qs qd qk ql w; wa ws wd wf PIP PROGR MENU ENTER DRC-MF PIP PROGR SOUND WIDE MODE SURROUND MODE PIC MODE PROGR RESET qs qd TV PIP operations (yellow label) 6 7 8 PIP PROGR +/ PIP PROGR ­ qk ql SOUND w; ENTER 13 13 13,14 13 13 14 Stereo/bilingual operations 2 A/B 16 continue Overview of Controls 9 continued es ed DVD Button Menu operations Function Display or cancel the menu. Confirm selected items. Select and adjust items. Enlarge the Teletext display. Input Teletext page number Display the next or previous page. Show TV screen while waiting for Teletext page. Display Teletext service contents. Reveal concealed information. Display Teletext broadcast. Stop Teletext display from scrolling. Page 20 20 20 17 17 17 17 17 17 17 17 17 33 wg 2 5 8 0 3 6 9 JUMP ef 1 4 7 wj MENU wk ENTER eh V, v, B, b wg wh 0 ­ 9 wl PROGR +/­ wh Teletext operations (green label) SOUND eg PIP PROGR MENU wj wk e; ea es ed ef eh DRC-MF PIC MODE ENTER PIP PROGR SOUND WIDE MODE SURROUND MODE PROGR wl eg RESET (red, green, yellow, blue) Access a FASTEXT menu. Set TV to factory setting. ej TV e; ea ej RESET 10 Overview of Controls Advanced Operations x Selecting the picture and sound modes You can select picture and sound modes and adjust the setting to your preference in the "PERSONAL" option. Selecting the picture mode DVD Press PIC MODE to select the desired picture mode. 2 5 8 0 3 6 9 JUMP 1 4 7 Select "DYNAMIC" "STANDARD" "HI-FINE" "PERSONAL" To view high contrast pictures. view normal pictures. view higher density pictures with mild contrast. receive the last adjusted picture setting from the "ADJUST" option in the "PICTURE" menu (see page 22). SOUND PIP PROGR MENU ENTER DRC-MF PIP PROGR PIC MODE SOUND WIDE MODE SURROUND MODE PIC MODE PROGR SOUND MODE RESET Selecting the sound mode Press SOUND MODE to select the desired sound mode. TV Select " DYNAMIC" To listen to dynamic and clear sound that emphasizes both the low and high tones. listen to sound that emphasizes voice and high tones. listen to soft sound. receive the last adjusted sound setting from the "ADJUST" option in the "SOUND" menu (see page 24). " " " DRAMA" SOFT" PERSONAL" Advanced Operations 11 x Viewing higher quality pictures with DRC-MF The Digital Reality Creation-Multi Function (DRC-MF) feature allows you to enjoy higher quality pictures on your TV. You can use the DRC-MF button to select "DRC1250" or "DRC PROGRESSIVE". SOUND PIP PROGR MENU Select "DRC1250" "DRC PROGRESSIVE" To view super real (higher density) pictures. reduce jitter of any small areas or scanning lines (e.g., letters or the edge of objects) on the screen. ENTER DRC-MF DRC-MF PIP PROGR PIC MODE SOUND WIDE MODE SURROUND MODE PROGR Note · The DRC-MF mode is not selectable when the "GAME MODE" or Picture-in-Picture ("PIP") mode is turned on. The DRC-MF logo ( Corporation. ) and "DRC-MF" are trademarks of Sony x Viewing the picture in wide mode When receiving a wide-mode (16:9) signal, the picture will appear "squeezed" (compressed) on your screen. Use the WIDE MODE button to view the picture with the optimal effect. ENTER DRC-MF PIP PROGR SOUND WIDE MODE SURROUND MODE Select "ON" "OFF" To view the picture in wide-mode (16:9). cancel wide-mode (16:9). WIDE MODE PIC MODE PROGR 12 Advanced Operations x Watching Picture-in-Picture (PIP) With the PIP feature, you can display two different TV programs or video input at the same time by using the button. 0 JUMP /SOUND/ / SOUND To MENU Press . To cancel the sub screen, press the button again. PIP PROGR + or PIP PROGR ­. . . SOUND. PIP PROGR PIP PROGR +/ PIP PROGR ­ Display a sub screen ENTER DTE PIP PROGR PIC MODE Change a program number in the sub screen Select a video input in the sub screen Swap pictures between the main and sub screens Swap sound between the main and sub screens A " " symbol will appear next to the program number or video input display to indicate which screen you are hearing. Notes · The DRC-MF mode is not selectable when PIP is turned on. · The picture and sound from the T (monitor output) terminals will always be from the main screen, even when you select the sub screen sound by pressing SOUND (see page 31 ...